EPILUX 800
Epoxy Anti-Corrosive Primer
PRODUCT A two pack zinc-free anti-corrosive epoxy that has been formulated specially for application to
DESCRIPTION stainless steel and pigmented to avoid galvanic corrosion. It contains:
• Zinc-free anti-corrosive pigments.
• Epoxy-polyamide resins giving a tough adherent film
DESIGNED USE • As a blast primer for stainless steel in aggressive environments.
• As a tie coat over two pack epoxies or zinc silicates or aged polyurethanes to improve
intercoat adhesion
• Suitable as a primer for upto C5 Environment as per ISO12944 Part 2 along with suitable
intermediate and topcoats
PHYSICAL DATA VOLUME SOLIDS
40 % + 2 %
(Based on ASTM D2697)
TYPICAL DRY FILM THICKNESS 25 microns
WET FILM THICKNESS 62 microns
THEORETICAL COVERAGE 16.0 m2/litre @ 25 microns DFT
VOC “As Supplied”
525 gms/ltr
(Based on ASTM D3960)
COLOUR Red Oxide
FINISH Matt
APPLICATION METHOD OF APPLICATION :
DETAILS This is the recommended method of application:
Maximum 5% Thinner may be added.
AIRLESS SPRAY
Tip Size: 0.38 - 0.48 mm (0.015 - 0.019 in)
Pressure: 110 - 160 kg/cm2 (1600 – 2300 psi)
This is also a suitable method of application.
CONVENTIONAL SPRAY Maximum 20% Thinner may be added
Tip Size: 1.80 - 2.20 mm (0.071 - 0.087 in)
Pressure: 2.75 - 3.45 kg/cm2 (40 - 50 psi)
May be used for difficult shapes or touch-up.
BRUSH OR ROLLER However, additional coats may be required to achieve
the recommended film thickness.
DRYING TIME:
Surface Over coating Interval
Touch Dry Hard Dry Pot Life
Temperature Minimum Maximum
15°C 2 Hrs 8 Hrs 16 Hrs 45 Days 12 Hrs
25°C 1 Hr 4 Hrs 8 Hrs 30 Days 6 Hrs
35°C ½ Hr 2 Hrs 6 Hrs 15 Days 3 Hrs
45°C 15 mins 1 Hr 4 Hrs 8 Days 2 Hrs
NO. OF COMPONENTS Two
Mixing Ratio 3 parts Base to 1 part Hardener (by volume)
Do not apply this product if the Relative Humidity
Application Conditions exceeds 85% or if the substrate temperature is within
3°C of the dew point
ADDITIONAL Thinner / Cleaning solvent Solvalux 7-45
Storage Instruction Store in a cool shaded dry area
INFORMATION Flash Point Mixed 20°C
Packaging 5 liters & 20 liters
Shelf Life 12 months from the date of manufacture.
March 2014 Version 0 Protective Coatings Sales & Service Dubai Tel 04- 3391000 Fax 04-3391322 Abu Dhabi Tel 02-6798202 Fax 02-6713774
EPILUX 800
Epoxy Anti-Corrosive Primer
SURFACE This product should be applied to a surface that has been blast cleaned. For blast cleaning of
PREPARATION stainless steel use aluminium oxide grit or any suitable abrasive.
• Remove all wax, oil and grease by solvent cleaning in accordance with the guide lines given
by SSPC-SPI.
• Where necessary remove weld spatter and round off all rough weld seams and sharp edges to a
smooth surface.
• Abrasive blast clean to a minimum standard of Sa 2½ Swedish Standard SIS 05 59 00 or ISO
8501-1 : 1988.
• Any surface defects revealed by blast cleaning should be ground, filled or treated in a suitable
manner.
• An average surface profile of 40 microns is acceptable, but this average should not exceed 50
microns.
• After blasting, remove dust from the surface.
• The surface to be coated must also be clean and dry.
• If the product is used as a tie coat over zinc primers - all surface contaminants (including zinc
salts) must be removed by lightly abrading and washing with clean fresh water.
PRODUCT USE • This product cannot be applied to a non-blasted substrate.
RESTRICTIONS • As common with all Epoxy products, this product also will tend to discolour and chalk on
exposure to direct sunlight.
• May also be applied between 25 and 40 microns DFT
• Contact Berger Representative for suggesting suitable paint system
SAFETY • Avoid contact with the skin and eyes. Wear suitable protective clothing such as overalls,
PRECAUTIONS goggles, dust masks and gloves. Use a barrier cream.
• Ensure that there is adequate ventilation in the area where the product is being applied. Do not
breathe vapor or spray.
• This product is flammable. Keep away from sources of ignition. Do not smoke. Take
precautionary measures against static discharge. In case of fire – blanket flames with foam,
carbon dioxide or dry chemicals
• Refer to MSDS for further information.
FIRST AID • Eyes: In the event of accidental splashes, flush eyes with water immediately and obtain medical advice
• Skin: Wash skin thoroughly with soap and water or approved industrial cleaner.
• DO NOT USE solvent or thinners.
• Inhalation: Remove to fresh air, loosen collar and keep patient rested.
• Ingestion: In case of accidental ingestion, DO NOT INDUCE VOMITING.
Obtain immediate medical attention
The information provided on this data sheet is not intended to be complete and is provided as general advice only. It is the responsibility
DISCLAIMER of the user to ensure that the product is suitable for the purpose for which he wishes to use it. As we have no control over the treatment of
the product, the standard of surface preparation of the substrate, or other factors affecting the use of this product, we are not responsible
for its performance nor would we accept any liability whatsoever or howsoever arising from the use of this product unless specifically
agreed to in writing by us. The information contained in this data sheet may be modified by us from time to time, and without notice, in
the light of our experience and continuous product development.
March 2014 Version 0 Protective Coatings Sales & Service Dubai Tel 04- 3391000 Fax 04-3391322 Abu Dhabi Tel 02-6798202 Fax 02-6713774
