Scribd
Upload
221 views2 pages

SAE Generator Adaptation Dimensions Guide

This document provides specifications for standard SAE single bearing generator adaptions, including dimensions for engine flywheel housings, flex discs, and instructions for measuring existing generators and engines to check if they match SAE standards. Dimensions such as outside diameters, bolt circle sizes, and distances from faces are given. Proper matching of generator and engine dimensions is important for correct positioning and installation.

Uploaded by

Jorge Mario Perdomo Perdomo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
221 views2 pages

SAE Generator Adaptation Dimensions Guide

This document provides specifications for standard SAE single bearing generator adaptions, including dimensions for engine flywheel housings, flex discs, and instructions for measuring existing generators and engines to check if they match SAE standards. Dimensions such as outside diameters, bolt circle sizes, and distances from faces are given. Proper matching of generator and engine dimensions is important for correct positioning and installation.

Uploaded by

Jorge Mario Perdomo Perdomo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd

Standard SAE Single Bearing Generator Adaptions

Engine Flywheel Housing Dimensions Engine Flywheel / Generator Flex Disc Dimensions
SAE XD XB Tapped Holes Twin XE XF XG Tapped Holes
SAE
# (mm) (mm) Qty. Size Disc (mm) (mm) (mm) Qty. Size
31.000 33.50 26.500 25.25 0
00 16 1/2-13 21 B-121 12 5/8-11
(787) (851) (673) (641) (0)
25.500 26.75 22.500 21.38 .62
0 16 1/2-13 18 B-118 6 5/8-11
(678) (678) (572) (543) (16)
23.000 24.38 18.375 17.25 1.00
1/2 12 1/2-13 14 SP-114 8 1/2-13
(584) (619) (467) (438) (25)
20.125 20.88 13.875 13.12 1.56
1 12 7/16-14 11-1/2 SP-111 8 3/8-16
(511) (530) (352) (333) (40)
17.652 18.38 12.375 11.62 2.12
2 12 3/8-16 10 C-110 8 3/8-16
(448) (467) (314) (295) (54)
16.125 16.88 10.375 9.62 2.44
3 12 3/8-16 8 C-108 6 3/8-16
(410) (429) (264) (244) (62)
14.250 15.00 9.500 8.75 1.19
4 12 3/8-16 7-1/2 C-107 8 5/16-18
(362) (381) (241) (222) (30)
12.375 13.12 8.500 7.88 1.19
5 8 3/8-16 6-1/2 C-106 6 5/16-18
(314) (333) (210) (200) (30)

10.500 11.25
6 8 3/8-16 17.755 15.50 .72
(267) (283) Delco 17.750” 8 5/8-11
(451) (394) (18)
15.500 13.88 .72
Delco 15.500” 8 5/8-11
(394) (353) (18)
12.750 11.00 0
Delco 12.750” 4 1/2-13
(324) (279) (0)

100 E. Randolph Street • PO Box 8003


Wausau, WI 54402-8003 USA
[Link] Phone: 715-675-3359
Measuring the SAE Adaption & Flex Discs of an Existing Generator

1. Make sure the surfaces of the main rotor and main stator cores are in the flush. This will
ensure the rotor is properly positioned and give the correct XG dimension.
2. Place a straight edge on the engine side of the drive discs, measure the distance (XG) to
the mating surface of the flwheel-housing adaptor.
3. Compare the generator XG dimension with the engine XG dimension and make sure they
match.
4. Measure the flex disc outside diameter - XE dimension.
5. Measure the size and bolt circles - XF dimension - of the holes in the drive discs. The
number of holes should be noted.
6. Compare the dimensions to the SAE standards on the chart supplied on page 1 and make
sure they match those on the engine.

Measuring the SAE Adaption & Flex Discs of an Existing Engine

1. Place a straight edge of the FACE of the flywheel housing. Measure the distance – XG
dimension - from the surface of the flywheel to the face of the flywheel housing.
2. Measure the inside diameter of the rabbit fit for the generator adaptor – XD dimension.
3. Measure the size, thread and bolt circle – XB dimension – of the holes in the flywheel
housing adaptor. Note the number of holes.
4. Measure the inside diamater of the recess the drive disc seat - XE dimension.
5. Measure the size, thread and bolt circle – XF dimension – of the holes in the flywheel for
drive disc mounting. Note the number of holes.
6. Compare the dimensions to the SAE standards on the chart supplied on page 1 and make
sure they match those on the engine.
G:\Marketing_Generators\TonyS\Common Downloads and Misc. Technical Literature\Adaptions\Standard SAE Adaptions - [Link]

100 E. Randolph Street • PO Box 8003


Wausau, WI 54402-8003 USA
[Link] Phone: 715-675-3359

You might also like