V1.

Creality Nebula Smart Kit Instruction Manual

SHENZHEN CREALITY 3D TECHNOLOGY CO., LTD.

FCC Caution:
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment. This device complies with part 15 of the FCC Rules.

Operation is subjectto the following two conditions:

(1) This device may not cause harmful irnterference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE:
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. Thse limits are designed to provide reasonable protection against harmful interferencein a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accor-
dancewith the instructions, may cause harmful interference to radico communications. However, there is no guarantee that
interference will not occur in a particular insallation. If this equipment does cause harmful interference to radio or teelevision
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the inter-
ference by one or more of the following measures: -Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that tto which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distancce 20cm between the radiator& your body
Precautions for use
1. Please use the product strictly in accordance with this manual to avoid personal injury and property damage.
2. Do not place the machine near any heat source or flammable or explosive objects. We suggest placing it in a well -venti-
lated, low-dust environment.
3. Please use the power adapter that comes with the machine to prevent damage to the machine.
4. Do not place this product in a vibration or unstable environment.
5. Please power off to clean the product regularly.
6. Users should comply with the laws and regulations of the corresponding countries and regions where the equipment is
located (used), abide by professional ethics, pay attention to safety obligations, and strictly prohibit the use of our products or
equipment for any illegal purposes. Creality will not be responsible for any violators' legal liability under any circustance.

Firmware upgrade
1. Wifi firmware upgrade: OTA upgrade through Creality cloud APP;
2. Device firmware upgrade: Go to the official website download center to download the latest firmware
[Link]
1. Product description

Product name: Creality Nebula PadN Model： NC01

Product model: N-Pad 01 Highest Resolution： 1920*1080

Main control chip: dual-core 1.2GHz Field of View： H： 95° D：112°

Storage memory: 8G Night Vision： Supports automatic switching

Screen type: IPS Manual Focus： Supports MF, knob adjustment

Screen size: 4.3inch Connection： USB connection

Screen resolution: 272*480 Rated Voltage： 5V

Touchl mode: resistive touch Product Dimensions： 55*40*35mm

WiFi protocol: 802.11b/g/n Net Weight： 130g

USB interface: USB2.0

Rated voltage: 5V

Vibration sensor: Yes

Resume printing: support 2. Packing list

Filament run-out detection: support

Supported languages: 10 languages 1. Nebula Pad x1

Product size: 133.17*83.3*19.6mm 2. Nebula Camera x1

Net weight: 145g 3. U disk x1

4. Tripod x1
*10 languages x1
5. G-Sensor cable
(Chinese, English, Japanese, German, French, Italian, Spanish, x1
6. G-Sensor
Portuguese, Russian, Turkish)
01
 7. Cross pan head self-tapping screw M3*8 x2

8. Hexagon socket head screw M3*6 x2

9. Hexagon socket head screw M3*8 x2

10. Hexagon socket head screw M5*10 x3

11. M5 T-nut x3

12. Cable tie x5

G-sensor interface Printer cable interface

[Link] view and interface description

G-Sensor cable

Connect to the Connect 5V Connect

Nebula pad power supply G-Sensor
USB 1

USB 2

02
4. Installation steps(take Ender-3 V2 Neo as an example) 4.2 AI Lidar and G-Sensor Installation

M3*8 self-tapping screw

4.1 Nebula pad installation
Obtain and print the bracket stl model in the U disk or
the official website download center;
Place the screen bracket on the side of the profile on
the right, and tighten it with 3 M5X10 screws and T-nuts;
Align the Nebula pad with the bracket and slide down
to lock it tightly
Connect the display cable.

Connection to nebula screen

M5 T-nut M5 X10 Note: Time-lapse photography files can be viewed on the Creality Cloud
03
5. Boot guide and device interface introduction

5.1 Boot guide

1 2 3

04
 4 5 6

05
 Notice：
The current UI is for reference only.
As the firmware is constantly being
upgraded, please refer to the latest
firmware UI on the official website.

7 8

06
5.2 Printer self-test

1 2 3

07
4 5 6

08
 7 8 9

09
 Warm reminder:
If there is an abnormality during the self-inspection, you can first refer to the FAQ
to find the cause of the fault; or scan the QR code to report the fault, and then solve
the fault through after-sales service

Notice：
The current UI is for reference only. As the firmware is constantly being upgraded,
please refer to the latest firmware UI on the official website.

10

10
5.3 Device interface introduction

Heated bed temperature

Nozzle temperature

Notice：
The current UI is for refer-
ence only. As the firmware is
constantly being upgraded,
please refer to the latest
firmware UI on the official
website.

Home page Parameters can be set manually

11
 Preparation

Function settings such as axis movement/temperature/feed and retreat, model fan cooling, etc. can be set through the
preparation interface.

12
Long press the model to select multiple Print file preview
and copy to the USB drive.
*Can copy up to 3 models

Local and USB drive model files can be managed on the print file preview interface

13
 Notice:
The current UI is for refer-
ence only. As the firmware is
constantly being upgraded,
please refer to the latest
firmware UI on the official
website.

Print page Print time The remaining time

Click on the model file to view the file details Model fan on/off
* Tick Print Calibration to improve print quality.

14
 Setting

Function settings such as Nebula pad system, network, and camera can be set through the Setting.

15
 Notice：
The current UI is for
reference only. As the
firmware is constantly being
upgraded, please refer to the
latest firmware UI on the
official website.

Print page

You can view FAQs, manuals, and log management through the customer service page.

16
6. Remote control

6.1Device interface in Creality Print slicing software

Ender 3 Pro Ender 3 Pro

Add device: a. Scan to add → select device

17
Click "Settings" → "Network", select the connected network to view the IP address

Add device: b. Manually enter the IP address to add the device

18
 Ender 3 Pro 文件：立方体_Ender 3 Pro···[Link]

Device list

19
 文件：立方体_Ender 3 Pro_0.4_CR-ABS_1.75_76h29m.gcode

立方体_Ender 3 Pro_0.4_···1.75_76h29m.gcode

Device print information details

Notice
The current UI is for reference only. As the firmware is constantly being upgraded, please refer to the latest firmware UI on the official
website.
20
6.2Creality cloud APP control

After binding the Creality cloud account on the Creality Nebula Pad, you can remotely control it through the app

21
 MADE IN CHINA

Join the Facebook Community

[Link]
+86 755 3396 5666
cs@[Link]