November 5, 1999 B-310
SGL-2000
Fire Alarm Control Panel
Section: Conventional Fire Alarm Control Panels
GENERAL California
State Fire
The NOTIFIER SGL-2000 is a cost-effective two-zone fire Marshal
alarm control panel. It is designed in accordance with
National Fire Protection Association (NFPA) Standards for 7165-0028:143
Protective Signaling Systems: 72 (Local), 72 (Remote S635 CS68
Station). The compact SGL-2000 control panel was tested
as a fire protective signaling system control unit under
Underwriters Laboratories Inc., Standard for Safety UL 864.
FEATURES
• Discrete component solid state design.
• Two-zone non-expandable construction.
• Class B (Style B) initiating circuits.
• Built-in surge suppression.
• Built-in brown-out circuitry.
• Single audible Style Y (Class B) circuit rated at 0.75 A.
• Low current drain of panel minimizes battery Amp/Hour
requirements.
• Supervision of battery.
• Float charger network.
• Two-wire smoke detector compatible.
• DC power tap rated at 100 milliamps.
• Dead-front construction.
• Trouble silence with resound.
• Ground fault circuit.
• Disable switch.
• Power-limited for use with limited-energy cable.
• In-panel signaling provides:
— Short pulse = Trouble.
— Long pulse = Resound.
— Steady signal = Alarm. 0380cov.wmf
• Trouble circuit monitors the following fault conditions:
— Open detector loop(s).
• Detection loop:
— Low battery voltage.
— Missing or disconnected battery. — Compatible with many types of two-wire detectors.
— Ground fault. — Power-limited for limited-energy cable.
— Low AC voltage (brown out). — Supervised Style B (Class B) operation.
— Loss of AC power. • Supervised Class B (Style Y) audible/visual signaling cir-
— “Off Normal” switch position. cuit.
— Open or shorted signaling (bell) circuit. • Compact solid state design.
• Control switches: • Automatic float charger.
— “Reset” for control and detectors. • Piezoelectric transducer for audible trouble signal.
— “Trouble Silence” with resound. • Panel will accept one of the following optional modules:
— “Disable” switch. — Supplementary alarm contacts, two Form-C.
• LED indicating lamps: — Supplementary alarm and trouble contacts,
— “Alarm 1” and “Alarm 2”. Form-C alarm, Form-C trouble (one each).
— “System Trouble”. — Remote station output, alarm only.
— “A.C. Power”. — Remote station output, alarm and trouble.
This document is not intended to be used for installation purposes. We try to keep our
product information up-to-date and accurate. We cannot cover all specific applications or ISO-9001
anticipate all requirements. All specifications are subject to change without notice. For Engineering and Manufacturing
more information, contact NOTIFIER. Phone: (203) 484-7161 FAX: (203) 484-7118 Quality System Certified to
International Standard ISO-9001 Made in the U.S.A.
One Fire-Lite Place, Northford, Connecticut 06472
DN-380 — Page 1 of 2
APPLICATIONS
The SGL-2000 fire alarm control panel is intended for use Always use two-wire detectors which have been listed
in small or medium sized commercial, industrial, and insti- by Underwriters Laboratories Inc. for use with this con-
tutional buildings. trol panel. For a list of compatible UL-listed smoke
detectors, please refer to the Installation Manual for
OPERATION this control panel.
Activation of a compatible two-wire detector or any nor-
mally open fire alarm initiating device will sound audible
signaling devices, illu-
minate an indicating 0380bd.wmf
LED at the control
panel, and operate an
optional module. The
optional modules can
be used to notify a re-
mote station, or initiate
a supplementary con-
trol function.
MAJOR
COMPONENT
& TERMINAL
LOCATIONS
OPTIONAL MODULES — Choose only ONE per control panel.
MP-AC24
Auxiliary Module MP-TR24
Transmitter Module
transmits Alarm to
responding authority.
0380mpac.wmf
0380mptr.wmf
MP-AC24 Notes: 1) For wiring, refer to UL power-limited re- MP-TR24 Notes: Connect to compatible UL listed polarity-sensi-
quirements. 2) Both sets of contacts must be connected to ei- tive remote station receiver. Output signal 18 to 28 VDC. 1) For
ther a non-power-limited or a power-limited circuit. DO NOT mix wiring, refer to UL power-limited requirements. 2) This circuit is
sets of contacts. 3) Refer to the Protected Premises Unit label suitable to leave the building. 3) This output is power-limited.
(located on the system door) and mark the dry contacts used as
non-power-limited circuits.
MP-TRT24
MP-AT24 Transmitter Module
transmits both Alarm
Auxiliary Module and Trouble to
responding authority.
0380mtrt.wmf
0380mpat.wmf
MP-AT24 Notes: *1) *Indicates non-trouble state. 2) All con- MP-TRT24 Notes: Connect to compatible UL listed polarity-sen-
tacts rated 3 A, 120 VAC/30 VDC. 3) For wiring, refer to UL sitive remote station receiver. Output signal 18 to 28 VDC. 1)
power-limited requirements. 4) Both sets of contacts must be For wiring, refer to UL power-limited requirements. 2) The MP-
connected to either a non-power-limited or a power-limited cir- TRT24 module DOES NOT comply with the requirement for sepa-
cuit. DO NOT mix sets of contacts. 5) Refer to the Protected rate trouble/alarm signal transmission. 3) This circuit is suitable
Premises Unit label (located on the system door) and mark the to leave the building. 4) This output is power-limited.
dry contacts used as non-power-limited circuits.
Page 2 of 2 — DN-380
