CR-IR346RU Service Manual

Preventive Maintenance (PM)

 0.1

CR-IR346RU Service Manual – Contents

Preventive Maintenance (PM)
1. Preventive Maintenance Program .............................................................................. PM-2
1.1 Preventive Maintenance Program List ............................................................. PM-2
1.2 Notations of Intervals ........................................................................................ PM-3
1.3 Preventive Maintenance Flow ........................................................................... PM-4
2. Details of Maintenance Procedures ........................................................................... PM-6
2.1 Opening the MAINTENANCE UTILITY Window ............................................... PM-6
2.2 Checking the Error Log ..................................................................................... PM-8
2.3 Checking the Erasure Lamp Lighting Time ..................................................... PM-10
3. Checking the Image/Conveyance ............................................................................... PM-11
3.1 Checking Nonuniformity/Sensitivity ................................................................ PM-12
3.2 Checking the Format ......................................................................................... PM-13
3.3 Checking the Output Characters ...................................................................... PM-14
4. Pulling Out the Machine .............................................................................................. PM-15
4.1 Powering OFF..................................................................................................... PM-15
4.2 Unlocking the Retainers .................................................................................... PM-15
4.3 Disconnecting the Cables ................................................................................. PM-18
5. Removing the Covers .................................................................................................. PM-19

6. Cleaning/Replacing the Air Filters .............................................................................. PM-20

7. Turning OFF the High-Voltage Switch ........................................................................ PM-21

8. Cassette Set Unit.......................................................................................................... PM-22

8.1 Removing the Cassette Set Unit....................................................................... PM-22
8.2 Cassette Set Unit (Cleaning the Suction Cups) .............................................. PM-23
8.3 Cassette Set Unit (Cleaning the Rollers) ......................................................... PM-23
8.4 Reinstalling the Cassette Set Unit.................................................................... PM-23
9. Erasure Conveyor ........................................................................................................ PM-24
9.1 Removing the Erasure Conveyor ..................................................................... PM-24
9.2 Erasure Conveyor (Cleaning the Reflection Guide) ....................................... PM-26
9.3 Erasure Conveyor (Cleaning the Guide Roller Assembly)............................. PM-26
9.4 Erasure Conveyor (Cleaning and Replacing the Cleaning Rollers) .............. PM-27
9.5 Erasure Conveyor
(Cleaning and Replacing the Erasure Lamps and Filter) ............................... PM-28
9.6 Erasure Conveyor (Cleaning the Conveyance Rollers).................................. PM-29
9.7 Reinstalling the Erasure Conveyor .................................................................. PM-29

010-051-01 CR-IR346RU Service Manual 0.1

08.30.2001 FM3058 (1)
 0.2

10. Side-Positioning Conveyor .......................................................................................... PM-30

10.1 Removing the Side-Positioning Conveyor ...................................................... PM-30
10.2 Side-Positioning Conveyor (Removing the Shock Absorbers) ..................... PM-31
10.3 Side-Positioning Conveyor
(Cleaning the Guides and Conveyance Rollers) ............................................. PM-32
10.4 Reinstalling the Side-Positioning Conveyor ................................................... PM-35
11. Subscanning Unit......................................................................................................... PM-36
11.1 Subscanning Unit (Cleaning the Cleaning Brushes) ...................................... PM-36
11.2 Subscanning Unit (Cleaning the Driven-Shaft Side Guide/Roller) ................ PM-37
11.3 Subscanning Unit (Cleaning the Kapton® Belt) ............................................... PM-38
11.4 Subscanning Unit (Cleaning the Flywheel/Light-Collecting Mirror/
Lower Rollers/Guides) ....................................................................................... PM-39
11.5 Subscanning Unit (Cleaning the Light-Collecting Guide) .............................. PM-43
11.6 Subscanning Unit (Cleaning the Rubber Belt) ................................................ PM-46
11.7 Subscanning Unit (Cleaning the Driving-Shaft Side Guide/Rollers) ............. PM-47
11.8 Reinstalling the Subscanning Unit................................................................... PM-48
12. Cleaning Inside the Machine ....................................................................................... PM-53

13. Turning ON the High-Voltage Switch .......................................................................... PM-53

14. Reinstalling and Cleaning the Covers ........................................................................ PM-54

15. Securing the Machine .................................................................................................. PM-54

15.1 Connecting the Cables ...................................................................................... PM-54
15.2 Securing the Machine ........................................................................................ PM-54
16. Checking the Image/Conveyance ............................................................................... PM-55

17. Checking the Error Log ............................................................................................... PM-55

18. Resetting the Erasure Lamp Lighting Time ............................................................... PM-56

010-051-01 CR-IR346RU Service Manual 0.2

08.30.2001 FM3058 (1)
Preventive Maintenance (PM) Control Sheet PM - 1

Control Sheet
Issue date Revision number Reason Pages affected
10/10/2000 00 New release (FM2887) All pages
08/30/2001 01 Support for software version A05 (FM3058) PM-1, 2, 5, 8, 10–13, 15–17, 19,
25, 32–36, 44, 49, 50, 56

010-051-01 CR-IR346RU Service Manual PM - 1

08.30.2001 FM3058
 PM - 2

1. Preventive Maintenance Program

1.1 Preventive Maintenance Program List
The interval requirements that presume the standard count processed (100 films per day)
are listed below.
Interval
requirements Periodic
Reference Time
Maintenance program replacement Remarks
section Count requirements
Interval parts
processed

2.2 Checking the error log 1Y

3 Checking the image/conveyance 1Y
4 Pulling out the machine 1Y

5 Removing the covers 1Y

6 Cleaning the air filters 1Y 30,000
Replacing the air filters 2Y 60,000 Air filter

7 Turning OFF the high-voltage switch 1Y

8.2 Cleaning the suction cups 1Y 30,000
8.3 Cleaning the rollers
9.2 Cleaning the reflection guide 1Y

9.3 Cleaning the guide roller assembly 1Y

9.4 Cleaning the cleaning rollers 1Y
Replacing the cleaning rollers 2Y 60,000 Cleaning roller

9.5 Cleaning the erasure lamps/filter 1Y

Replacing the erasure lamps 2Y Erasure lamp 1800 h

9.6 Cleaning the conveyance rollers 1Y
10.2 Removing the shock absorbers 1Y

10.3 Cleaning the guides/conveyance rollers 1Y

11.1 Cleaning the cleaning brushes 1Y

11.2 Cleaning the driven-shaft side guide/roller 1Y

11.3 Cleaning the Kapton® belt 1Y

Cleaning the flywheel/ light-collecting mirror/

11.4 1Y
lower rollers/guides

11.5 Cleaning the light-collecting guide 1Y

11.6 Cleaning the rubber belt 1Y

11.7 Cleaning the driving-shaft side guide/rollers 1Y

12 Cleaning inside the machine 1Y
13 Turning ON the high-voltage switch 1Y

14 Reinstalling and cleaning the covers 1Y

16 Checking the image/conveyance 1Y
17 Checking the error log 1Y
18 Resetting the erasure lamp lighting time 2Y
[Link]

010-051-00
010-051-01 CR-IR346RU Service Manual PM - 2
10.10.2000 FM3058
08.30.2001 FM2887 (1)
 PM - 3

1.2 Notations of Intervals

In this volume, either of the following symbols is indicated for each maintenance program.
Before initiating any maintenance operation, you should become familiar with the following
symbols.

Indicates a program that must be performed at 1Y (1 year) intervals or when the

1Y count processed has reached about 30,000.

Indicates a program that must be performed at 2Y (2 year) intervals or when the

count processed has reached about 60,000.
2Y

010-051-00 CR-IR346RU Service Manual PM - 3

10.10.2000 FM2887 (1)
 PM - 4

1.3 Preventive Maintenance Flow

START

2.1 Opening the MAINTENANCE UTILITY Window

2.2 Checking the Error Log

2.3 Checking the Erasure Lamp Lighting Time

3. Checking the Image/Conveyance

4.1 Powering OFF

4.2 Unlocking the Retainers

4.3 Disconnecting the Cables

5. Removing the Covers

Cleaning Replacement
1Y 2Y

6. Cleaning/Replacing the Air Filters

7. Turning OFF the High-Voltage Switch

8.2 Cassette Set Unit (Cleaning the Suction Cups)

8.3 Cassette Set Unit (Cleaning the Rollers)

9.2 Erasure Conveyor (Cleaning the Reflection Guide)

9.3 Erasure Conveyor (Cleaning the Guide Roller Assembly)

Cleaning Replacement
1Y 2Y

9.4 Erasure Conveyor (Cleaning and Replacing the Cleaning Rollers)

Cleaning Replacement
1Y 2Y

9.5 Erasure Conveyor (Cleaning and Replacing the Erasure Lamps/Filter)

9.6 Erasure Conveyor (Cleaning the Conveyance Rollers)

A
[Link]

010-051-00 CR-IR346RU Service Manual PM - 4

10.10.2000 FM2887 (1)
 PM - 5

A
Removal only
10.2 Side-Positioning Conveyor (Removing the Shock Absorbers) for maintenance
after first year
1Y of operation
10.3 Side-Positioning Conveyor (Cleaning the Guides/Conveyance Rollers)

11.1 Subscanning Unit (Cleaning the Cleaning Brushes)

11.2 Subscanning Unit (Cleaning the Driven-Shaft Side Guide/Roller)

11.3 Subscanning Unit (Cleaning the Kapton® Belt)

11.4 Subscanning Unit (Cleaning the Flywheel/Light-Collecting Mirror/

Lower Rollers/Guides)

11.5 Subscanning Unit (Cleaning the Light-Collecting Guide)

11.6 Subscanning Unit (Cleaning the Rubber Belt)

11.7 Subscanning Unit (Cleaning the Driving Shaft Side Guide/Rollers)

12. Cleaning Inside the Machine

13. Turning ON the High-Voltage Switch

14. Reinstalling and Cleaning the Covers

15.1 Connecting the Cables

15.2 Securing the Machine

16. Checking the Image/Conveyance

17. Checking the Error Log

18. Resetting the erasure lamp lighting time

END
[Link]

010-051-01
010-051-00 CR-IR346RU Service Manual PM - 5
08.30.2001
10.10.2000 FM3058
FM2887 (1)
 PM - 6

2. Details of Maintenance Procedures

2.1 Opening the MAINTENANCE UTILITY Window
(1) Power ON the CL.

(2) Power ON the RU.

(3) Press the [Windows] key to display the Start menu of Windows.

Press

010-051-00 CR-IR346RU Service Manual PM - 6

10.10.2000 FM2887 (1)
 PM - 7
(4) Select [Run...] from the Start menu of Windows, and type
[“C:¥ProgramFiles¥FujiFilm¥FCR¥Tool¥[Link]”] to open the RU MAINTE-
NANCE UTILITY window.

Windows Update

Programs

Favorites

Documents

Settings

Search

Help

Run...
#1
[Click]
Log Off Administrator...
Run ?

Shut Down... Type the name of a program, folder, document, or

Internet resource, and Windows will open it for you.

Open: "C:\ProgramFiles\FujiFilm\FCR\Tool\[Link]" #2 [Type]

#3 [Click] OK Cancel Browse...

RU SERVICE UTILITY window

CR-IR346RU MAINTENANCE UTILITY
EACH RU SETTING
CONNECTION TEST
RU NAME ru0 LIST OF EXISTING RU
NEW
RU NAME IP ADDRESS
RU IP ADDR 172 16 1 10 ru0 [Link]
MUTL PING

INSTALL EDIT HISTORY EDIT CONFIGURATION

BACKUP (RU→HD→FD) RESTORE (FD→HD→RU)

ERROR LOG CONFIGURATION

EXECUTE EXECUTE

ALL RUs SETTING

UNINSTALL PREVIOUS VERSION VERSION UP

[Link]

010-051-00
010-051-00 CR-IR346RU Service Manual PM - 7
10.10.2000
10.10.2000 FM2887
FM2887 (3)
(1)
 PM - 8

2.2 Checking the Error Log

■ Opening the WINNT\System32\[Link] Window

(1) Start the M-Utility.

CR-IR346RU MAINTENANCE UTILITY

EACH RU SETTING
CONNECTION TEST
RU NAME ru0 LIST OF EXISTING RU
NEW
RU NAME IP ADDRESS
RU IP ADDR 172 16 1 10 ru0 [Link]
#1 [Click] MUTL PING

INSTALL EDIT HISTORY EDIT CONFIGURATION

BACKUP (RU→HD→FD) RESTORE (FD→HD→RU)

ERROR LOG CONFIGURATION

EXECUTE EXECUTE

ALL RUs SETTING

UNINSTALL PREVIOUS VERSION VERSION UP

C:WINNT\System32\[Link]
_
[Ru0] login : cr ir346 #2 [Type/ENT]
Password : #3 [Type/ENT]
_
[cr ir346]
#4 [Type/ENT] -> mutl

0. QUIT
1. LOG
2. VERSION
3. TEST
4. ELECTRICAL UTILITY
5. SCANNER UTILITY
6. MECHANICAL UTILITY
7. SOFTWARE UTILITY
8. BACKUP MEMORY
9. HV OFF
>

[Link]

010-051-01
010-051-00 CR-IR346RU Service Manual PM - 8
08.30.2001 FM2887
10.10.2000 FM3058 (1)
 PM - 9

REFERENCE
If no error logs exist, the following message appears.
THE LOG IS EMPTY.
RESULT: OK

(2) Select the log to check the error log.

C:WINNT\System32\[Link]
0. QUIT
1. LOG
2. VERSION
3. TEST
4. ELECTRICAL UTILITY
5. SCANNER UTILITY
6. MECHANICAL UTILITY
7. SOFTWARE UTILITY
8. BACKUP MEMORY
9. HV OFF
> 1 #1 [Type/ENT]

0. QUIT
1. ERROR LOG
2. TRACE LOGS
LOG > 1 #2 [Type/ENT]

0. QUIT
1. DISPLAY
2. SAVE TO FTP-SERV
3. CLEAR
LOG > ELG > 1 #3 [Type/ENT]

0. QUIT
1. ALL
2. SUMMARY
LOG > ELG > DSP > 1 #4 [Type/ENT]

0. QUIT
1. FATAL
2. WARNING
3. BOTH
LOG > ELG > DSP > ALL > 3 #5 [Type/ENT]

***ERROR LOG ALL***

CODE DATE
11311. 2000.01.01. ----------------------------------- #6 [Check]
0. END (DEFAULT=0) :

[Link]

010-051-00 CR-IR346RU Service Manual PM - 9

10.10.2000 FM2887 (1)
 PM - 10

2.3 Checking the Erasure Lamp Lighting Time

(1) Open the MAINTENANCE UTILITY window.

(2) Open the EDIT HISTORY window.

(3) Check the erasure lamp lighting time.

MAINTENANCE UTILITY window

CR-IR346RU MAINTENANCE UTILITY
EACH RU SETTING
CONNECTION TEST
RU NAME LIST OF EXISTING RU NEW
RU NAME IP ADDRESS
RU IP ADDR ru0 [Link] (2) #1 [Select/Click]
MUTL PING (2) #2 [Click]

INSTALL EDIT HISTORY EDIT CONFIGURATION

BACKUP (RU->HD->FD) RESTORE (FD->HD->RU)

ERROR LOG CONFIGURATION

EXECUTE EXECUTE EDIT HISTORY window

CR-IR346RU MAINTENANCE UTILITY
ALL RUs SETTING PROCESSING AND WARNING COUNTER

UNINSTALL RESET
PREVIOUS VERSION VERSION UP SINCE 2000 10 10

TOTAL PROCESSING COUNTER

18*24 cm 0 08*10 inch 12

24*30 cm 0 10*12 inch 1

14*14 inch (35*35 cm) 2

14*17 inch (35*47 cm) 1

All IP SIZES 16

SCN READ PROCESSING COUNTER 5

WARNING COUNTER
IP READ&HANDLING 0

CASSETTE SET OPERATION 0

ERASURE LAMP

RESET SINCE 2000 10 10

TOTAL TIME FOR THE ERASURE LAMP LIGHTING 0 HOURS (3)#1

[Check]
CANCEL RESET ALL SET

(3) #2 [Click]
[Link]

010-051-01
010-051-00 CR-IR346RU Service Manual PM - 10
08.30.2001 FM2887
10.10.2000 FM3058 (1)
 PM - 11

3. Checking the Image/Conveyance

The following checks are made in this section.
• Check for nonuniformity, sensitivity, and conveyance
• Check for format
• Check for output characters

■ Preparation Procedures
◆ NOTES ◆
• Use IPs of all sizes used in the hospital for checking the image/conveyance.
Note, however, that the IP type to be used should be the VI type.
• Make sure that no important data has been exposed on the IP to be used.

(1) Erase the natural radiation and image accumulated on the IP to be used.
“RU Instruction Manual/2.4 When Only Image Erasure is to be Performed
(Primary Erasure)”

(2) Place a steel rule (150-mm) on the cassette and expose it at 1 mR.

Cassette setting direction

Cassette

Steel rule
Exposure face

[Link]

◆ NOTE ◆
If the IP cannot be exposed at 1 mR, it should be exposed at a level equivalent to 1
mR, with reference to the following exposure conditions.
Note, however, that those conditions are for standard IP setup reference.
Distance: 1.8 m
Voltage: 80 kV
Amperage: 50 mA
Time: 0.013 sec

010-051-01
010-051-00 CR-IR346RU Service Manual PM - 11
10.10.2000
08.30.2001 FM2887
FM3058 (1)
 PM - 12

■ Outputting the Film for Image Check

◆ NOTES ◆
• The film to be outputted is used to check nonuniformity/sensitivity, format, and output
characters.
• The trimming function should be disabled.
“CL Service Manual/Function-specific Reference/2. Setup Necessary When
Editing the Film Annotation Character Format“

(1) Output the image exposed at 1 mR.

At this time, check to see that the IP conveyance mechanism of the RU is operating
normally.
“RU Instruction Manual/2. Operating Procedures”
◆ CHECKS ◆
• There should be no offensive noise or odor.
• There should be no IP jam.
• After reading, the IP should be free from any scratch or damage.
If anything abnormal is found, see [Troubleshooting Volume].

3.1 Checking Nonuniformity/Sensitivity

(1) Make sure that there is no unusual nonuniformity found on the output film and on the
image displayed on the image monitor.
◆ CHECKS ◆
There should be no unusual nonuniformity.
If anything abnormal is found, see [Troubleshooting Volume].

010-051-01
010-051-00 CR-IR346RU Service Manual PM - 12
08.30.2001 FM2887
10.10.2000 FM3058 (1)
 PM - 13

3.2 Checking the Format

For this check, the format misalignment is verified.
(1) Using the output film, measure the white blank portion.

Measure
Image frame

White blank portion Measure

[Link]

◆ CHECK ◆
• Make sure that the white blank portion is 2 mm or less.
• When the dimension of the white blank portion of the steel rule is converted to its
actual dimension, the difference between the resulting value and the actual steel rule
should be 2% or less.
If anything abnormal is found, see [Troubleshooting Volume].

010-051-01
010-051-00 CR-IR346RU Service Manual PM - 13
10.10.2000
08.30.2001 FM2887
FM3058 (1)
 PM - 14

3.3 Checking the Output Characters

Make sure that the film character format information that was set in “Outputting the Film for
Image Check” is displayed on the output film. Also verify that none of the characters look
blurred or broken.

(1) Check the output characters.

◆ CHECKS ◆
• Make sure that the character format information that was set is correct.
• Check for anything abnormal, such as blurred or broken characters.
If anything abnormal is found, see [Troubleshooting Volume].

REFERENCE
The details of output characters and the character display locations are as follows.
(1) Hospital name (medical institution name)

FUJI HOSPITAL 04001676 A0000 A020

(12) IP barcode No.
(2) EDR mode and menu code
(3) System ID and image No.

(4) Patient ID
(5) Patient name (10) Film mark
(13) Image processing conditions
(7) Sex
(8) Age or date of birth
G 1.0G#0.7+0.50R5Q0.5 R->L G1.0G#0.7+0.50R5Q1.0
SKULL GENERAL
L 4.0 S200C✼1.2✼1.0AP 0000000001 John Smith [M] 23
1992. 11. 27 [17:43] SCALE: 50% RT-04

(14) Exposure menu (9) Set processing information

(15) Standardization conditions (11) Reduction ratio
(17) Exposure time
and correction item
(6) Date of exposure [Link]
(16) Image reversal mark

010-051-00 CR-IR346RU Service Manual PM - 14

10.10.2000 FM2887 (2)
(1)
 PM - 15

4. Pulling Out the Machine

4.1 Powering OFF
(1) Power OFF the CL.

(2) Power OFF the RU.

4.2 Unlocking the Retainers

The procedures for unlocking the retainers vary depending on how the machine is retained.
Take steps with reference to the relevant procedures.

■ When the Machine is Secured by the Adjustable Feet

Machine

[Loosen]
Na12 (x4)

Caster

Adjustable foot

[Link]

010-051-00
010-051-01 CR-IR346RU Service Manual PM - 15
10.10.2000
08.30.2001 FM2887
FM3058 (1)
 PM - 16

■ When the Machine is Secured by the Retainers

#1
[Remove] Bolt 12x20, W12 (x2)
#3
[Move] Machine

Mashine

#2
[Loosen] Adjustable foot
Caster
4 or 2-Na12

Adjustable foot

[Link]

◆ NOTES ◆
When securing the adjustable feet, pay attention to the following points.
•The four adjustable feet should be evenly loaded.
However, if there is too little space on the right and left sides in the machine installa-
tion place to secure the adjustable feet on the rear side, the two adjustable feet on
the front side should be secured in place. In this case, the two adjustable feet and
two casters should be evenly loaded.
• When the adjustable feet are secured, the casters should be detached from the floor.

010-051-01
010-051-00 CR-IR346RU Service Manual PM - 16
08.30.2001 FM2887
10.10.2000 FM3058 (1)
 PM - 17

■ When the Machine is Secured by the Table

Table

#3
[Move] Machine

#1
[Remove] T6x12 (x2)

Bracket

Machine

#2
[Loosen] Adjustable foot
Caster
4 or 2-Na12

Adjustable foot
[Link]
◆ NOTES ◆
When securing the adjustable feet, pay attention to the following points.
• The four adjustable feet should be evenly loaded.
However, if there is too little space on the right and left sides in the machine installa-
tion place to secure the adjustable feet on the rear side, the two adjustable feet on
the front side should be secured in place. In this case, the two adjustable feet and
two casters should be evenly loaded.
• When the adjustable feet are secured, the casters should be detached from the floor.

010-051-01
010-051-00 CR-IR346RU Service Manual PM - 17
08.30.2001
10.10.2000 FM3058
FM2887 (1)
 PM - 18

4.3 Disconnecting the Cables

(1) Disconnect the power cable and interface cable.

#2
[Disconnect]
Interface cable
#1
[Disconnect] Power cable
[Link]

010-051-00 CR-IR346RU Service Manual PM - 18

10.10.2000 FM2887 (1)
 PM - 19

5. Removing the Covers

#3
[Remove] T4x8 (x4)
Left-hand side cover

Top cover
Upper rear cover

#6
[Loosen] #7
T4x12 (x4) [Remove] DT3x6 (x4)

X
#3
[Remove] T4x6 (x4)
#4
[Remove] T4x6 (x6)
Upper #2
light protect [Remove] T4x12 (x6)
plate

Right-hand side cover

HHS Label
No.2
Lower light protect plate
#5
#1 [Remove] T4x6 (x4)
[Remove] Front cover [Link]

010-051-01
010-051-00 CR-IR346RU Service Manual PM - 19
10.10.2000
08.30.2001 FM2887
FM3058 (1)
 PM - 20

6. Cleaning/Replacing the Air Filters

Clean or replace the air filters.

When one year has passed or when 30,000 IPs have been processed
1Y → The air filters should be cleaned.

When two years have passed or when 60,000 IPs have been processed
2Y → The air filters should be replaced.

Sponge filter
[Clean] [Replace]

1Y 2Y

[Clean/Replace]
Air filter

[Clean]
Air filter

HHS Label
No.2
[Link]

010-051-00 CR-IR346RU Service Manual PM - 20

10.10.2000 FM2887 (1)
 PM - 21

7. Turning OFF the High-Voltage Switch

(1) Turn OFF the high-voltage switch.

SCN12A board LED is lit when in the

ON position.

High-voltage
switch S1
S1
ON OFF

■ S1
[Link]

010-051-00 CR-IR346RU Service Manual PM - 21

10.10.2000 FM2887 (1)
 PM - 22

8. Cassette Set Unit

To gain access to the locations to be cleaned, the suction cup assembly should be removed.

8.1 Removing the Cassette Set Unit

(1) Remove the suction cup assembly.

CAUTION
When installing or removing the suction cup assembly, support the IP removal arm by
hand.
If the procedures are performed without supporting it, the IP removal arm may be bent
or otherwise damaged.

REFERENCE
Move the IP removal arm to the IP suction position before proceeding to the next step.
IP removal arm
Cassette set unit

FRONT

[Link]

#2 [Remove]
DT3x6 (x2)

PUSH Suction cup assembly

IP removal arm

PUSH
#1 [Remove] Lid opening bracket

[Link]

010-051-00 CR-IR346RU Service Manual PM - 22

10.10.2000 FM2887 (1)
 PM - 23

8.2 Cassette Set Unit (Cleaning the Suction Cups)

(1) Clean the suction cups (suction surfaces) with a moistened cloth.

Suction cup assembly

[Clean] Moistened cloth

Suction cup (suction surface)

[Link]

8.3 Cassette Set Unit (Cleaning the Rollers)

(1) Clean the rollers and guide rollers with a moistened cloth.

[Clean] Moistened cloth

Guide roller

Roller

[Clean] Moistened cloth

Guide roller
[Link]

8.4 Reinstalling the Cassette Set Unit

(1) For reinstallation, reverse the procedures described in “8.1 Removing the Cassette Set
Unit.”

010-051-00 CR-IR346RU Service Manual PM - 23

10.10.2000 FM2887 (1)
 PM - 24

9. Erasure Conveyor
To gain access to the locations to be cleaned, each section of the erasure conveyor should
be removed.

9.1 Removing the Erasure Conveyor

(1) Remove the guide roller assembly.

(2) Remove the reflection plate bracket.

(3) Remove the cleaning roller assembly.

(2)
[Remove] DT3x6 (x2)

ONT
FR
Cleaning roller
assembly

Guide roller assembly

Reflection plate bracket

(3)
(1)
[Remove] BR4x8
[Remove] DT3x6 (x2) [Link]

010-051-00 CR-IR346RU Service Manual PM - 24

10.10.2000 FM2887 (1)
 PM - 25
(4) Remove the box.

(5) Remove the light protect plate.

(6) Disconnect the connectors.

(7) Remove the lamp assembly.

INV12B board

CN14

(6) #2
[Disconnect]
Connector

(6) #1
[Release] CN13 CN12 CN11
Clamp

INV12A board
FRONT

T
ON
FR
(7)
[Remove] BR3x6

Light protect
plate
(5)
Yellow filter
[Remove]
T4x6 (x2)
Lamp assembly (4)
[Remove]
BR4x8
Box

[Link]

010-051-00
010-051-01 CR-IR346RU Service Manual PM - 25
10.10.2000
08.30.2001 FM2887
FM3058 (1)
 PM - 26

9.2 Erasure Conveyor (Cleaning the Reflection Guide)

(1) Clean the reflection surface of the reflection guide, as well as the guides attached
thereto, with a moistened cloth.

Reflection guide

#1
[Remove] Guide (x4) #3
#2 [Clean] Moistened cloth
[Clean] Moistened cloth Reflection surface
[Link]

(2) Reinstall the guides.

9.3 Erasure Conveyor (Cleaning the Guide Roller Assembly)

(1) Clean the rollers and guides of the guide roller assembly with a moistened cloth or
ethanol.

Guide roller assembly

[Clean] Moistened cloth or ethanol

Guide (x4)

[Clean] Moistened cloth or ethanol

Roller (x4)
[Link]

010-051-00 CR-IR346RU Service Manual PM - 26

10.10.2000 FM2887 (2)
(1)
 PM - 27

9.4 Erasure Conveyor (Cleaning and Replacing the Cleaning

Rollers)
(1) Clean or replace the cleaning rollers.

When one year has passed or when 30,000 IPs have been processed
1Y → The cleaning rollers should be cleaned.

[Clean] Cleaning roller

[Link]

When two years have passed or when 60,000 IPs have been processed

2Y → The cleaning rollers should be replaced.

#3
[Remove] Spur gear #5
[Replace] Cleaning roller
E6
Bearing
#1
[Remove] DT3x6
Bearing
Antistatic brush

Bracket

Box

#2 Bearing
[Remove] DT3x6
#4
[Remove] E6

[Link]

(2) Reassemble the cleaning roller assembly.

When the cleaning roller is replaced, reverse its removal procedures.

010-051-00
010-051-00 CR-IR346RU Service Manual PM - 27
10.10.2000
10.10.2000 FM2887
FM2887 (2)
(1)
 PM - 28

9.5 Erasure Conveyor (Cleaning and Replacing the Erasure

Lamps and Filter)
(1) Clean the erasure lamps with a moistened cloth.

When one year has passed or when the lamps have been lit for about 900
hours
1Y
→ The erasure lamps should be cleaned.

When two years have passed or when 1,800 hours have been exceeded, the
2Y erasure lamps should be replaced.

If the lamp-on time has exceeded 1,800 hours or if two years have passed since the
start of use, the lamps should be replaced with new ones.

(2) Clean the filter with an ethanol-moistened cloth.

Rib

Holder plate Filter

T
ON
FR

(1) #1
[Remove] DT3x6 (x2)

Yellow filter

(1) #3
(2) [Remove] Lamp
[Clean] Ethanol (1) #2 (1) #4
[Remove] Filter [Clean]
Moistened cloth Holder plate
(1) #1
[Remove] DT3x6 (x2) [Link]

(3) Reassemble the erasure lamp assembly by reversing the procedures of step (2).

010-051-00
010-051-00 CR-IR346RU Service Manual PM - 28
10.10.2000
10.10.2000 FM2887
FM2887 (2)
(1)
 PM - 29

9.6 Erasure Conveyor (Cleaning the Conveyance Rollers)

(1) Remove the antistatic bracket assembly.

#3 Antistatic bracket assembly

[Remove] DT3x6

#2
[Disconnect] Connector
CNBCR

#1
[Remove] DT3x6

[Link]

(2) Clean the conveyance rollers

[Clean] Moistened cloth

Conveyance roller

[Link]

(3) Reinstall the antistatic bracket assembly by reversing the procedures of step (1).

9.7 Reinstalling the Erasure Conveyor

(1) Reverse the procedures described in “9.1 Removing the Erasure Conveyor.”

010-051-00 CR-IR346RU Service Manual PM - 29

10.10.2000 FM2887 (1)
 PM - 30

10. Side-Positioning Conveyor

10.1 Removing the Side-positioning Conveyor

DETAIL A DETAIL B

#2
[Remove]
#2 BR4x8 (x2)
[Remove] BR4x8 (x2)

#1
[Disconnect]
Connector CNC1

#1
[Disconnect] Connector CNMC3
#1
[Disconnect] Connector CNC10

Hold this position.

HHS Label No.2

Side-positioning conveyor [Link]

010-051-00 CR-IR346RU Service Manual PM - 30

(1)
10.10.2000 FM2887 (2)
 PM - 31

10.2 Side-Positioning Conveyor (Removing the Shock

Absorbers)
(1) Remove the shock absorbers.

When one year has passed since installation

1Y → The shock absorbers should be removed.

P
TO

Side-positioning conveyor

[Peel] Shock absorber

[Link]

010-051-00 CR-IR346RU Service Manual PM - 31

10.10.2000 FM2887 (1)
 PM - 32

10.3 Side-Positioning Conveyor (Cleaning the Guides and

Conveyance Rollers)
(1) Remove the movable guide.

Movable guide

#2
[Remove]
BR3x6 (x2)
#1
[Remove]
Extension spring

[Link]

010-051-01
010-051-00 CR-IR346RU Service Manual PM - 32
08.30.2001 FM2887
10.10.2000 FM3058 (1)
 PM - 33
(2) Release the grip of the conveyance rollers.

Grip release cam

[Rotate] Gear

Grip release cam

[Link]

(3) Remove the cloth roller.

#2
[Clean] Moistened cloth
Cloth roller
Anti-static bracket assembly

#1
[Remove]
BR3x6 (x2)
[Link]

010-051-00
010-051-01 CR-IR346RU Service Manual PM - 33
10.10.2000
08.30.2001 FM2887
FM3058 (1)
 PM - 34
(4) Clean the conveyance rollers and guides with a moistened cloth.

[Clean] Moistened cloth [Clean] Moistened cloth

Guide Roller

[Link]

(5) Reinstall the movable guide, antistatic bracket assembly, and cloth roller by reversing
their removal procedures.

010-051-01
010-051-00 CR-IR346RU Service Manual PM - 34
08.30.2001 FM2887
10.10.2000 FM3058 (1)
 PM - 35

10.4 Reinstalling the Side-Positioning Conveyor

(1) Reverse the procedures for removing the movable guide.
◆ NOTE ◆
Make sure that the upper grip roller (short) is fitted in the notch of the arm.

Arm

Upper grip roller (short)

[Link]

(2) Reverse the procedures for removing the cloth roller.

REFERENCE
The side-positioning conveyor should be reinstalled after the preventive maintenance
for the subscanning unit has been completed.

010-051-00
010-051-01 CR-IR346RU Service Manual PM - 35
10.10.2000
08.30.2001 FM2887
FM3058 (1)
 PM - 36

11. Subscanning Unit

11.1 Subscanning Unit (Cleaning the Cleaning Brushes)

■ Procedures on the Driven Shaft Side (Machine Rear Side)

(1) Remove the cleaning brush assembly.

(2) Clean the cleaning brushes.

(1)
[Loosen] DT3x6 (x2) HHS Label No.2

Cleaning brush
assembly

(2)
[Clean] Vacuum cleaner
Cleaning brush (x2)

HHS Label No.2

[Link]

010-051-00
010-051-01 CR-IR346RU Service Manual PM - 36
10.10.2000
08.30.2001 FM2887
FM3058 (1)
 PM - 37

11.2 Subscanning Unit (Cleaning the Driven-Shaft Side Guide/

Roller)
(1) Remove the driven-shaft grip roller (upper).

(2) Clean the driven-shaft grip roller with a moistened cloth.

(2) [Clean]
Moistened cloth HHS Label No.2
Grip roller (upper)

Hook Hook

(1) #2 (1) #2
[Remove] [Remove]
Extension Extension
spring HHS Label No.2 spring
L=50 mm L=39 mm

CHECK

[Link]

010-051-00
010-051-00 CR-IR346RU Service Manual PM - 37
10.10.2000
10.10.2000 FM2887
FM2887 (2)
(1)
 PM - 38

11.3 Subscanning Unit (Cleaning the Kapton® Belt)

(1) Remove the Kapton® belt.
◆ INSTRUCTION ◆
When cleaning the Kapton® belt, ethanol should not be used. If ethanol is used, the
date and other markings on the Kapton® belt will be wiped out.

(2) Clean the Kapton® belt.

HHS Label No.2

#1
[Remove] Extension spring 76 mm

#3
[Clean]
Moistened cloth
Kapton® belt

#2
[Shift] Bracket
[Link]

010-051-00 CR-IR346RU Service Manual PM - 38

10.10.2000 FM2887 (2)
(1)
 PM - 39

11.4 Subscanning Unit (Cleaning the Flywheel/Light-Collecting

Mirror/Lower Rollers/Guides)

■ Removal Procedures
◆ INSTRUCTION ◆
Use care not to damage the surface in contact with the Kapton® belt.

(1) Remove the flywheel.

(2) Clean the flywheel.

Driving shaft

HHS Label
No.2

Allen wrench

#2
[Clean] Ethanol
Flywheel

#1
[Remove] Na20

[Link]

010-051-00
010-051-00 CR-IR346RU Service Manual PM - 39
10.10.2000
10.10.2000 FM2887
FM2887 (2)
(1)
 PM - 40

(2) Remove the spring and gears.

HHS Label
No.2 HHS Label
No.2

Spacer
#1 Gear (large)
[Remove]
Spring

Gear (small)

#2
[Remove] BR3x12

HHS Label
No.2

#3
[Remove]
V3x6 (x2)

Light-collecting mirror

[Link]

010-051-00 CR-IR346RU Service Manual PM - 40

10.10.2000 FM2887 (1)
 PM - 41
(3) Remove the light-collecting mirror.
REFERENCE
When removing the light-collecting mirror, rotate the guide A in the direction of the
arrow as shown below to facilitate access to the screw that retains the light-collecting
mirror.

[Rotate] Guide A

HHS Label No.2

HHS Label No.2

[Link]

CAUTIONS
• Do not wipe the light-collecting mirror with a dry cloth. If so, the light-collecting mirror
may be scratched or otherwise damaged.
• If the lens cleaning paper becomes soiled, replace it with a new one.
• Wipe the light-collecting mirror until the lens cleaning paper becomes no longer
soiled.

(4) Using the lens cleaning paper moistened with ethanol, clean the reflection surface of
the light-collecting mirror.

Light-collecting mirror

[Clean] Ethanol
Reflection surface

[Link]

REFERENCE
To clean the light-collecting mirror, two sheets of lens cleaning paper should be folded
in four and then moistened with ethanol.

010-051-00 CR-IR346RU Service Manual PM - 41

10.10.2000 FM2887 (1)
 PM - 42
(5) Using a moistened cloth, clean the driven-shaft grip roller (lower) and the IP running
surface (guide) on the driven-shaft side.

[Clean] Moistened cloth

HHS Label No.2
IP running surface (guide)

[Clean] Moistened cloth

Driven-shaft grip roller (lower)

[Link]

010-051-00 CR-IR346RU Service Manual PM - 42

(2)
10.10.2000 FM2887 (1)
 PM - 43

11.5 Subscanning Unit (Cleaning the Light-Collecting Guide)

■ Removal Procedures
(1) Remove the after-reading conveyor cover.

Spacer
After-reading HHS Label No.2
conveyor cover

Spacer
#2
[Remove] BR3x6 (x2)
#1
[Remove]
DT3x8 (x2)
[Link]

010-051-00 CR-IR346RU Service Manual PM - 43

10.10.2000 FM2887 (2)
(1)
 PM - 44

◆ INSTRUCTION ◆
The light-collecting guide should be removed along the rails.

(2) Remove the light-collecting guide.

#1 PMT12A board
[Disconnect]
Connector PMT2

Light-collecting section #1
Light-collecting
[Disconnect]
guide assembly
Connector PMT1

#2
[Remove] BR3x6 (x2)

DETAIL A
B
#3 [Remove] BR3x10
HHS Label No.2

DETAIL B #4 [Remove] BR3x10 (x2)

FRONT

[Link]

010-051-01
010-051-00 CR-IR346RU Service Manual PM - 44
08.30.2001 FM2887
10.10.2000 FM3058 (1)
(1)
 PM - 45

CAUTIONS
• Do not wipe the light-collecting guide with a dry cloth. If so, the light-collecting guide
may be scratched or otherwise damaged.
• If the lens cleaning paper becomes soiled, replace it with a new one.
• Wipe the light-collecting surface of the light-collecting guide until the lens cleaning
paper becomes no longer soiled.

REFERENCE
To clean the light-collecting guide, two sheets of lens cleaning paper should be folded
in four and then moistened with ethanol.

(3) Clean the light-collecting surface of the light-collecting guide.

FRONT
Light-collecting guide assembly

[Clean] Ethanol
Light-collecting surface
[Link]

010-051-00
010-051-00 CR-IR346RU Service Manual PM - 45
10.10.2000
10.10.2000 FM2887
FM2887 (2)
(1)
 PM - 46

11.6 Subscanning Unit (Cleaning the Rubber Belt)

CAUTION
The rubber belt should not be removed.

(1) Clean the rubber belt.

[Clean] Moistened cloth

Rubber belt

HHS Label No.2 Antistatic brush

Moistened cloth

While rotating the rubber belt Screwdriver

by hand, clean the inner side
of the rubber belt with a
moistened cloth.

[Link]

010-051-00 CR-IR346RU Service Manual PM - 46

10.10.2000 FM2887 (1)
 PM - 47

11.7 Subscanning Unit (Cleaning the Driving-Shaft Side Guide/

Rollers)
(1) Remove the driving-shaft grip roller (upper).

(2) Clean the driving-shaft grip roller (upper) with a moistened cloth.

HHS Label
No.2

Hook

Hook

(1)
[Remove]
Extension (2)
spring [Clean] Moistened cloth
L=39 mm Grip roller (upper)

(1)
[Remove]
Extension spring
L=50 mm

[Link]

010-051-00
010-051-00 CR-IR346RU Service Manual PM - 47
10.10.2000
10.10.2000 FM2887
FM2887 (3)
(1)
 PM - 48
(3) Using a moistened cloth, clean the driving-shaft grip roller (lower) and the IP running
surface (guide) on the driving-shaft side.

HHS Label
No.2
[Clean] Moistened cloth
IP running surface (guide)

[Clean] Moistened cloth

Driving-shaft grip roller (lower)

[Link]

11.8 Reinstalling the Subscanning Unit

(1) Reinstall the driving-shaft grip roller (upper).

“11.7 Subscanning Unit (Cleaning the Driving-Shaft Side Guide/Rollers)

(2) Reinstall the light-collecting guide.

◆ NOTE ◆
While looking into the peep hole, verify that the φ4 mm hole is visible.

HHS Label
No.2

Peep hole
φ 4mm hole
[Link]

010-051-00 CR-IR346RU Service Manual PM - 48

10.10.2000 FM2887 (1)
 PM - 49

#4 PMT12A board
[Connect]
Connector PMT2

Light-collecting section #4
[Connect] Light-collecting
Connector PMT1 guide assembly

#3
[Secure] BR3x6 (x2)

B
DETAIL A

#2 [Secure] BR3x10 HHS Label No.2

DETAIL B #1 [Secure] BR3x10 (x2)

FRONT

[Link]

010-051-01
010-051-00 CR-IR346RU Service Manual PM - 49
10.10.2000
08.30.2001 FM2887
FM3058 (1)
 PM - 50
(3) Reinstall the after-reading conveyor cover.

“11.5 Subscanning Unit (Cleaning the Light-Collecting Guide), ■ Removal

Procedures”

(4) Reinstall the light-collecting mirror.

“(3) of 11.4 Subscanning Unit (Cleaning the Flywheel/Light-Collecting Mirror/

Lower Rollers/Guides)”

(5) Reinstall the spring and gears.

◆ INSTRUCTION ◆
The gear (large) and gear (small) should be mounted in place as illustrated below.

Sensor (SZ5) Gear (large)

FRONT

Slit (large) Slit (small)

Pinionless section

Gear (small) D-shaped cut [Link]

(6) Reverse the procedures for removing the driven shaft grip roller (upper).
(7) Reverse the procedures for removing the cleaning brush.

010-051-01
010-051-00 CR-IR346RU Service Manual PM - 50
08.30.2001 FM2887
10.10.2000 FM3058 (1)
 PM - 51
(8) Reverse the procedures for removing the flywheel.
◆ INSTRUCTIONS ◆
• The Kapton® belt should be mounted with its date indicating side up, so that the
arrow mark faces the side plate.
• After mounting the Kapton® belt, manually rotate the flywheel to verify that the
Kapton belt does not come off.

Side plate
5
0 9
03 Rotation mark

00
Date

Kapton® belt
[Link]

(9) Reverse the procedures for removing the Kapton® belt.

(10) Reinstall the driven-shaft grip roller (upper).

“11.2 Subscanning Unit (Cleaning the Driven-Shaft Side Guide/Roller)

(11) Reinstall the cleaning brushes.

“11.1 Subscanning Unit (Cleaning the Cleaning Brushes)”

010-051-00 CR-IR346RU Service Manual PM - 51

10.10.2000 FM2887 (2)
(1)
 PM - 52
(12) Reinstall the side-positioning conveyor in reverse order of removal.

HHS Label No.2

Side-positioning unit

DETAIL A DETAIL B

#1
[Secure]
BR4x8 (x2)

#2
[Connect]
Connector CNC1 #1 [Secure]
BR4x8 (x2)

#2
[Connect] Connector CNMC3
#2
[Connect] Connector CNC10
[Link]

010-051-00 CR-IR346RU Service Manual PM - 52

10.10.2000 FM2887 (1)
 PM - 53

12. Cleaning Inside the Machine

(1) Using a vacuum cleaner, remove dust deposited inside the machine.

13. Turning ON the High-Voltage Switch

(1) Turn ON the high-voltage switch.

SCN12A board
LED is lit when in the
ON position.

High-voltage
S1 switch S1
ON OFF

■ S1
[Link]

010-051-00 CR-IR346RU Service Manual PM - 53

10.10.2000 FM2887 (1)
 PM - 54

14. Reinstalling and Cleaning the Covers

CAUTION
Before reinstalling the covers, make sure that the high-voltage switch of the SCN12A
board is in the ON position.

(1) Reinstall the covers by reversing their removal procedures.

“5. Removing the Covers”

(2) Clean the covers.

15. Securing the Machine

15.1 Connecting the Cables.
(1) Connect the cables by reversing their disconnection procedures.

“4.2 Disconnecting the Cables”

15.2 Securing the Machine

(1) Secure the machine by reversing the procedures for unlocking the retainers.

“4.1 Unlocking the Retainers”

010-051-00 CR-IR346RU Service Manual PM - 54

10.10.2000 FM2887 (1)
 PM - 55

16. Checking the Image/Conveyance

“3. Checking the Image/Conveyance”

17. Checking the Error Log

“2.2 Checking the Error Log”

010-051-00 CR-IR346RU Service Manual PM - 55

10.10.2000 FM2887 (1)
 PM - 56

18. Resetting the Erasure Lamp Lighting Time

When the erasure lamps are replaced, be sure to reset the erasure lamp lighting time.

(1) Open the MAINTENANCE UTILITY window.

(2) Open the EDIT HISTORY window.

(3) Reset the erasure lamp lighting time.

MAINTENANCE UTILITY window
CR-IR346RU MAINTENANCE UTILITY
EACH RU SETTING
CONNECTION TEST
RU NAME LIST OF EXISTING RU NEW
RU NAME IP ADDRESS
RU IP ADDR ru0 [Link] (2) #1 [Select/Click]
MUTL PING (2) #2 [Click]

INSTALL EDIT HISTORY EDIT CONFIGURATION

BACKUP (RU->HD->FD) RESTORE (FD->HD->RU)

ERROR LOG CONFIGURATION

EXECUTE EXECUTE EDIT HISTORY window

CR-IR346RU MAINTENANCE UTILITY
ALL RUs SETTING PROCESSING AND WARNING COUNTER

UNINSTALL RESET
PREVIOUS VERSION VERSION UP SINCE 2000 10 10

TOTAL PROCESSING COUNTER

18*24 cm 0 08*10 inch 12

24*30 cm 0 10*12 inch 1

14*14 inch (35*35 cm) 2

14*17 inch (35*47 cm) 1

All IP SIZES 16

SCN READ PROCESSING COUNTER 5

WARNING COUNTER
IP READ&HANDLING 0

CASSETTE SET OPERATION 0

ERASURE LAMP

RESET SINCE 2000 10 10

TOTAL TIME FOR THE ERASURE LAMP LIGHTING 0 HOURS (3)#1

[Check]
CANCEL RESET ALL SET

(3) #2 [Click]
[Link]

010-051-00
010-051-01 CR-IR346RU Service Manual PM - 56
10.10.2000
08.30.2001 FM2887
FM3058 (1)
 PM - 57

BLANK PAGE

010-051-00 CR-IR346RU Service Manual PM - 57

10.10.2000 FM2887 (1)