1ison Transndssion 3000/4000 series fault code list -Truck nrarmal.. . hitps://[Link]-tran...

Workshop, repair and service manuals,

W ring diagrams, fault codes PDF - more
than 1000+ truck manuals are available
for free downioad!

®,

AIIison Transmission
3000/4000 series fault code
list

Allison Transmission PDF Service Manuals

Table of fault codes, Automatic transmission Series 3000, 4000 with

electronic control system Gen4

Table of fault codes

AIlison Transrfussion 3000/4000 series fault code list -Truck lrmnual. . . [Link]

Su conexi6n no es segura
El propietario de [Link]!ick.)let ha cc]nfigurado su sitio web de manera
incorrecta. Para evitar que su informaci6n sea robada, Fire fox no ha conectado con
este sitio web.

1\,1`( ,I) i( ,I I.),.;\,i(:,,i ;

Avanzado

LampCheckTrans
Errorcode
Description Control system response

C1312 Low voltage s gnal to turn on the retarder OFF Retarder does not turn on
C1313 High voltage s gnal to turn on the re{arder OFF Retarder does not turn on
P0122 Intermittent or ow gas pedal position OFF The default value is used.
sensor signal
P0123 High sisnal level pedal position serrsor gas OFF The default value is used.

P0218 Oil temperature too h©h OFF A control pattern is [Link].

P0562 Low supply voltage coritrol unit OFF The ban on locking torque
converter. DNA
P0602 Control unit not programmed ON F3emains neutral
P0610 Error of the additiorra! equipment of ON T!D A calibration data is used.
the car with the control unit
P0613 Coiitrol unit processor error OFF All solenoids are OFF.
P0614 Incompatibility of ECM and TCM data ON Only neutral` rear and
to adjust engine torque second gear. Torque lock
inhibit, shift adaptation OFF

P0634 Control unit temperature exceeded ON DNS, SOL OFF, active hydraulic
coutrol`
)63E No auto throttle throttle position input C)N The default value i§ w§ed,
sigrlal
P063f No auto coolant temperatiire signal OFF
AIlison Tinnsrfussion 3000/4000 series fault code list -Truck rmrnral.. . hitps://[Link]/allisomtransrission/allison-tram...

P0657 HSDl open circuit ON SOL OFF, DNA. Interlocking of

the torque converter, prohibition
of the main modulation.

P0658 HSDl low voltage ON DNS, SOL OFF, hydraulie contro

active

P0659 HSDl high voftage ON DNS, SOL OFF, hydraiilic contro

active

P0702 The control unit did rrot recognize the ON Uses standard connouration
automatic transmission confic]uration.
P0703 Brake Sensor Circuit Malfunction OFF On the garbage triroks cannot
enable ND. If the code is
active, then the work Of
the retarder is prohibited.
P0708 High level sisnal from the currem ON Igrrore the sigma] of the strip
trarismissien seltsor. sw-itch
P070C Low oil level sefrsor s-Egnal OFF -
P070D [Link] oil level sefisor signal OFF -
P0711 Noi+standard oil temperature sensor ON Uses the default temperature
sional
P0712 Low oil temperature sensor signal ON Uses standard temperature
value
P0713 Hish oil temperature sensor signal ON Uses standard temperatiire
value
P0716 Non-standard Turbine Wheel Speed ON DNS, automatic transmission is
Sensor Sidnal blocked on the ciITrent transfer
P0717 Turbine wheel speed sensor signal ON DNS, automatic transmission is
missiTra blocked on the currerit transfer
P0719 ABS braking selrsor sinnal low OFF Considers ABS OFF
P071A Incompatible RELS inout ON RELS OFF
P071D Wrong inpif( sismal Of the special ON
function (wire 101 and 142)
P0721 Non-standard output speed serrsor ON DNS, automatic transmission
sidnal remains on the current transfer

P0722 No output speed sensor signal ON DNS, automatic transmission

stays on current gear
P0726 Nor+standard engine speed sensorsismal OFF ltses standard turbine speed
value
P0727 Missing engine speed sensor s©nal OFF Uses standard turbine speed
value
P0729 Vwong gear ratio in 6tli gear ON DNS, trying to enable 5th, then
Sid gear
P0731 Incorrect gear ratio in 1 st gear ON DNS, trying to enable 2ird, then
5th gear
P0732 Wrong gear ratio in 2nd gear ON DNS, trying to errable 3rd, then
5tn gear
Incorrect gear ratio in Sid gear ON DNS, trying to enable 4tn, then
6th gear
Incorrect gear ratio in 4th gear ON DNS, trying to enable 5th, then
3rd gear
P0735 Invalid gear ratio in 5th gear ON DNS trying to enable 6th then
the 3rd, then the 2nd gear
Pn736 Wmrm near ralin in reuersp near nNLS hlrtr,keri nn neirfral
AIlison Transndssion 3000/4000 series fault code list -Truck mammal... [Link]

P0741 Slipping clutch locking torque converte ON -

P0752 Stuck solenoicl Ssl pressure ON DNS
reoulatirm valve
P0776 Malfunction in the PCS2 solenoid ON DNS, RPR
hvdraulic circuit
P0777 MalfLlnction in the PCS2 ON DNS, RPR
solenoid hvdraulic circut
P0796 Fault in the hydraulic circuit of the ON DNS, RPR
PCS3 solenoid
P0797 Fault in tlie liydraulic cirouit of the ON DNS. RPF{
PCS3 solenoid
P0842 Pst pressure sensor low voltage. ON DNS, automatic transmission
stays on current qear
P0843 Pst pressure sersor high voltage. ON DNS, automatie transmission
stays on current Gear
P0847 PS2 Pressure Sensor Low Voltaqe ON -
P0848 PS2 Pressure Sensor Hidh Voltaqe ON -
PO880 Tlie disappearance of the power OFF
control unit during eimine operation
PO881 Cordro[ unit voltage too low or jumping OFF -
P0882 The voltage on the control unit is be!o ON DNS, SOL OFF, hydraulic
llormal control is active

P0883 The voltage on the comrol unit is OFF

above normal
PO88A Oil filter cJoqqed OFF -
PO88B Oil fitter heavily cloqqed OFF -
P0894 No transfer of the moment in first gear ON DNS remains on 1 transmission
P0897 Gear oil requires reDlacemen[ ON -
P0960 Open circuit solenoid valve modulation ON
DressiITe
P0962 Low voltage in the solenoid circuit ON DNS, SOL OFF, hydraulic
cofitrol is active
of the pressure modulating vale
P0963 Modulation vale solenoid circuit hish ON
voltage
Pressure
P0964 PCS2 solenoid open circuit ON DNS, SOL OFF, hydraulic
corfrol is active

P0966 PCS2 solenoid circuit low voltage ON DNS, SOL OFF, hydraulic
control js active

Su conexi6n no es segura

P0967 PCS2 solenoid circilit high voltage ON DNS, SOL OFF, hydraulic
control active

P0968 PCS3 solenoid open circuit ON DNS, SOL OFF, hydraulic

control active

P0970 PCS3 solenoid circuit low voltage ON DNS, SOL C)FF, hydraulic
control active
AIlison Transndssion 3000/4000 series fault code list -Truck rrarmal.. . [Link]

P0971 PCS3 solenoid cirouit high voltage ON DNS, SOL OFF, hydraiilic
comrol active

P0973 Low voltage in the circuit of the ON DNS, SOL OFF, hydraulic
solenoid SS1 con{ro! active

P0974 lligh voltage in the solenoid circuit SS1 ON DNS, SOL OFF, hydraulic
[Link] active

P0975 SS2 solenoid open circuit ON On 7-speed automatie

tralismissions,1st and 7th gear
are not included.
P0976 Low voltage in the solerroid circuit SS2 ON On 7-speed automatic
transmissions.1st and 7th gear
are Trot inelirded, prchibition of
tacking the torque converter
P0977 Lngh voltage in the solenoid circut SS2 ON On 7-speed automatic
transmissions,1st and 7th gear
are Trot i[reluded.
PO989 The sisnel from the retarder has OFF Rctarder does not turn on
interruDtions
PO990 The sisnal from the retarder has a OFF Retarder does not turn on
short circuit
P1739 Wrong gear ratio in low gear ON DNS, prohibition of work on 1
transfer
P1891 Accelerator pedal position sensor OFF Uses the standard pedal
sfanal below norrnal depression valL]e_
P1892 Accelerator pedal position sensor OFF Uses the staridard pedal
signal is above normal depression value.
P2184 Low voltage sisnel coolant OFF uses standard temperature
tenmerature serror valLle
P2185 Coolant temperature sensor siemal hish OFF Uses standard temperature
veltaqe value
P2637 Disturbance in the operation of the ON [Link] of the SEM system
torque control system when changing
oears SEM
P2641 Disturbance in the system of torque ON Disable LRTP system operation
limiting on the lower gears LRIP
P2669 HSD2 open circuit ON SOL OFF, blocking the torque
converter` banning the main
modulation, DNA
P2670 HSD2 low voltage ON DNS, SOL OFF, hydraulic
control active

P2671 HSD2 high vettage ON Due, SOL OFF, hydraulic

control actrfe

P2684 HSD3 open circuit ON SOL OFF, blocking the torque

converter, banning the main
nduLatien. DNIA

2685 HSD3 low voltage ON DNS, SOL C}FF, hydraulic

colitrol acthe
Allison Transrission 3000/4000 series fault code list -Truck manual.. . hitps://[Link]/allisomtransnrissioulallison-tram..

P2686 HSD3 hieh voltage ON DNS, SOL OFF, hydraulic

control active

P2714 Fault in the hydraulic [Link] of the PCS4 ON DNS, RPR

solenoid
P2715 Fault in the hydraulie circuit of the PCS4 ON DNS, SOL OFF, hydraulic
solenoid control active

P2718 PCS4 solenoid open circuit ON DNS, SOL OFF] hydraulic

control active

P2720 PCS4 solenoid circuit low voltage ON DNS, SOL OFF, hydraulic
control actie

P2721 PCS4 solenoid circuit hieh voltage ON DNS, SOL OFF, hydraulic
control active

P2723 Malfunction in the Pcsl solenoid ON DNS, RPR

hvdrau]ic circuit
P2724 Malfunction in the Pcsl solenoid ON DNS. RPR
hvdraulic circut
P2727 Pcsl solenoid open circuit ON DNS, SOL OFF, hydraulic
control active

P2729 Pcsl solenoid circuit low voltage ON DNS, SOL OFF, hydraulic
comrol active

P2730 Pcsl solenoid circuit high voltage ON DNS, SOL OFF, hydraulic
control active

P2736 PCS5 solenoid open circuit ON The ban on the work of

the retarder
P2738 PCS5 solerroid circuit low voltage ON The prohibition of work on the
1st gear, the work of
the retarder, the took of the
tongue converter
P2739 PCS5 solenoid circuit hish voltage ON The ban on the work of
the retarder
P2740 High oil retarder temperature OFF -
P2742 Low sisnal level of the retarder oil OFF Uses standard oil temperature
tenperature sensor
P2743 High sisnal level of the OFF Uses standard oil temperature
oil re{arder temperature sensor
P2761 Open circuit solelroid lockout torque ON Prohibition of locking torque
converter converter
P2763 Low voltage in the lock-up torque ON Prohibition of locking torque
converter solenoid circuit converter
P2764 High voltage in the torque converter ON Prohibition of locking torque
lock-un solenoid circuit converter
P2789 Friction clutch wear reaches the limitvalue ON

P278A Erroneous signal Kickdown OFF Kickdown mode ban

P2793 Communication error with gear switch ON Ignores pulse width
modulation, if the skynal
through the CAN bus is also
lost, it is blocked in the last
directior` selected
r2808 Fautt in the rtydraiilic circuit of the PCSS ON DNS. RPR
solerroid

P2809 Fault in the hydraulie circuit of the PCS6

AIlison Tralisrission 3 000/4000 series fault code list -Truck marnral... [Link]

P2812 PCS6 solenoid open circuit ON DNS, SOL OFF, hydraulic contro
active

P2814 PCS6 solenoid circuit low voltage ON DNS, SOL OFF, hydraulic contro
act`Ive

P2815 PCS6 solenoid circuit hieh voltage ON DNS, SOL OFF, hydraulic contro
active

U0001 Hieh Speed CAN Bus Counter (lESCAN) OFF Uses standard values, prohibiting
overflow the operation of the torque
control system when changing
gears
|J0010 CAN Bus Couliter Overflow (lESCAI`D OFF Uses starrdard values, prohibiting
the operation of the torque
control system when changing
gears
UOIOO Loss of communication with engine / ON Uses standard values
powertrain unit (J1586)
u0103 Loss of communication with the first gea ON Remains in the selected gear,
selector
monitors the sisnal to change
the direction of
movement. The display goes
out for 10 seconds, then
shiows - I - - I -
U0115 Communication error with engine coTitro[unit ON Uses standard values, DNA

U0291 Communicatieii error with secondary ON Remains in the selected gear,

gear selector monitors the sismal to change
the direction Of
movement. The display goes
out for 10 seconds. then
srfuorws - I - - I -
U0304 Primary gear selector not compatible ON DhB blocked in neutral
with J1939 Protocol
U0333 Secondary switch not compatible with ON DNS blocked in neutral
J1939 Protocol
u0400 Vlolation of data trarrsnrission protocol ON
J1939
|ro404 I nadequate information from the primary ON F2emaine in the selected gear,
gear selector monitors the sisnal to change
the direction of
movement. The display goes
out for 10 seconds, then
shoNNS - I - - I -

The control unit receives incorrect data OFF

from the engine / power unit control
unit that is jrroluded jn the J1939 data
bus,
Inadequate information from the Remains in the selected gear,
secondary gear selector monitors the siemal to change
the direction of
AIlison Translrission 3 000/4000 series fault code list -Truck marmal„. trys://[Link]-transrfussion/allison-tram..

Prognostic Features For Motorhome Series (MH)

3000/4000 SeriesT``` And Transmissions : 3000 and
Tcl 0" Allison 4000 Product Families
Transmissions WTEC lil Controls and
Allison Transmission 5th Aliison 4th Generation
Gen Operation F Controls
Adobe Acrobat Document Allison Transmission

[489.9 KB] [Link]

Adobe Acrobat Document
Download
[2.1 MB]

Download

Comments: 0

Name: *

Message: *