Manuals+ — User Manuals Simplified.

SPY LT565 APP Car Alarm System User Manual

Home » SPY » SPY LT565 APP Car Alarm System User Manual

Contents
1 SPY LT565 APP Car Alarm System
2 Button Functions
3 Functions
3.1 Electrical / pneumatic locking
option
4 FOC Caution
5 TECHINICAL DATA
6 Documents / Resources
7 Related Posts

SPY LT565 APP Car Alarm System

Button Functions

Arm:
Press ” button once, the siren will chirp once, flash light will gleam once central door locking system will lock
automatically. power window will be rolled up within 30s. After 3 seconds, LED indicator will gleam, then the
system enter into arm status, and Sensors/Side door/Car Hood/ACC begin to detect.

Disarm:
Oin arm status, press’s “button once, the siren will chirp twice, flash lights will gleam once, central door locking
system will unlock automatically, If door not opened within 25s, the system will return back to arm status and
central door locking system will lock automatically again. Keep pressing for 2s, remote trunk release Oin disarm
status, keep pressing”button for 1s to release the trunk.

Silent Arm:
Press “button once, Siren will not chirp and the flash light will gleam once, central door locking system will lock
automatically. After 3 seconds, the system will enter into arm status, LED indicator will gleam, and sensors/side
door hood/ACC begin to detect

Car finding:
In arm status, keep pressing ” “button for 2 seconds, flash lights will gleam for 15s, siren will chirp at the same
time, and the engine will be cut off, Press the button again to stop and enter into arm status. In am status, keep
pressing Xbutton for 2 seconds, flash lights will gleam for 15s, siren will not chirp, and engine will be cut off, Press
the button again to stop and enter into arm status in arm status or disarm status, press the ” button once, siren will
chirp for 15 times, flash lights will gleam for 15s also at the same time, engine will be cut off: Press the button
again to stop

Functions

1. Alarming Door /Hood/Engine Protection

In arm status, if the car door, hood is opened by force or start the engine etc, anyone of them will trigger system
to alarm. Siren will chirp loudly, flash lights will gleam, car engine will be cut off. It will alarm for 40s, once the
system is triggered. After 40s, will stop automatically and return back to arm status.
2. Siren Pause:
If the system is triggered to alarm, except disarm by pressing “button, press any button can pause, but the
system will still keep in arm status.
3. Ultrasonic sensor:
(optional) Press “button or “X button once, the system will enter into arm status, Ultrasonic sensor will begin to
work after 5s, and to detect after 8s lest the radiation has an impact on human body.
4. Power window:
In disarm status, keep pressing “9” and ” button simultaneously. the window will close one by one, it will stop
after 15s.
5. Trigger identify
In arm status, if system is triggered, there will be two ways to alarm: if triggered by light hit, the siren will chirp
ten times, flash lights will gleam at the same time, and engine will be cut off. If system is triggered by heavy hit
(such as hit on window, hit by external force), the siren will chirp 40s intermittently, flash lights will gleam at the
same time, and engine will be cut off.(Note: If ultrasonic sensor is triggered in silent arm status, the siren will
chirp 40s intermittently flash lights will gleam, and engine will be cut off.)
6. Central door locking system automation:
When car moving. press “button or “P “button can control central door locking system to lock or unlock, but
alarm system will not work. Driving Control Function-Close all doors before driving, then switch key to ACC ON
position. Press on the footbrake after 15s, doors will lock automatically This function can avoid doors being
locked when there is no one in the car. Take off the key before getting off the car, the doors will unlock
automatically It is convenient for passengers to get on/off the car. Option methods: Switch key to “ON” position,
 and keep pressing ” ” button for 2s, the siren will chirp twice. Driving Control Function will be on at the moment;
Keep pressing ° button for 2s, the siren will chirp once. Driving Control Function will be off.
Note: Function option is only for point; Factory default setting is on.
7. Anti-hijacking (Option by remote)
When moving, press “X button once, flash lights will gleam quickly (just preparatory phase), then press”A
“button for 2s enter into Anti-hijacking status flash lights will gleam urgently, and siren will chirp, then the engine
will be cut off after 40 seconds. Only press cancellation button or reset button can get rid of Anti-hijacking
status.
8. Car finding:
O Car finding in sound/flash mode: In arm status, keep pressing “button for 2s, the siren will chirp for 15s, flash
lights will gleam simultaneously, and engine will be cut off. 3Car finding in silent mode: In arm status, keep
pressing button for 2s, flash lights will gleam 15 times, the siren will not chirp, and engine will be cut off.
9. .Re-arm automatically:
When disarm the system accidentally, do not open the door within 25s, the system will retune back to arm
status automatically.
10. LED indicator: OI n am:
LED indicator will gleam twice discontinuously every time @Warning: LED indicator will light on.
11. Precision electronic detector:
When any part of the cars suffer from hitting or beating, the system wll be triggered to alarm to scare the
gangster away and to ensure car safety
12. Engine blocking:
Cut-off relay can cut off engine power and make the engine fail to stat.
13. Instruction ding warning
In arm status, if the system is triggered by hoodhood open or ACC. When disarmed, siren will emit a “B” sound
for 5 times. If above mentioned situate on happens, please check if anyone hide in the car firstly, so as not be
hijacked when enter the car.
14. Help/Clear the way:
When driving. press button, the siren will chirp for 15 times, and the flashlights will flash 15 seconds. It can
achieve the purpose to call for help urgently Press the” button once again, it well stop.
15. Dome light delay automation:
Normally. the system will begin to detect the doors after entering into arm status 8s later. But f the car is fitted
with dome light system will delay to 30s] whenever turn off the dome light or close the door well, the system will
begin to detect the car doors When press the button to disarm, the system detect the doors opened within 1s.
(dome light of some cars will light on when disarm to unlock).system will regard as the car is fitted with dome
light system. If not switch the key to ON position within 55s, the system will regard as a false disarm, then will
return back to the arm status
16. Power off memory:
In arm status, f power is cut off, the system will return back the am status when power on, When power is cut
off in normal condition, the system will also retune to normal state once the power is stored. This function can
ensure to guard against theft effectively, and will nat cause any trouble when repair the car.
17. Arm Rem ending:
After parking 10s,the flash light will gleam 3 times to remind arming the system.
18. (ACC-ON) Emergency disarm:
 In case of the transmitter is lost or damaged, dampened or c that cannot disarm the system. The following
methods can be used to disarm the system Switch the ACC from OFF to ON 10 times to disarm the system, the
siren will chirp two times, flash lights will gleam twice. After system being disarmed, the owner can drive the car
normally turbid strongly so
19. Door unclosed reminding(Option by remote)
Before driving, If any door is not closed well and not switch the key to ACC ON position, the Flash lights will
gleam all the time, and will stop automatically after 30 seconds to warn the rear car owner of paying attention to
safety. @Before driving, If any door is not closed well and switch the key to ACC ON position, the Flash lights
will gleam all the time until the door is closed well to warn the rear car owner of paying attention to safety.
@Option method: Keep pressing the “button for 2 seconds to activate side door unclosed reminding function
with the siren chirping twice; Keep pressing “”for 2 seconds again to exit the function with the siren chirping
once
Note: Factory default is on

Electrical / pneumatic locking option

The system default setting is Electrical lock, central locking system signal output time is 0.5S(JP6 short circuit will
be on 0.5S position ),If the ca is fitted with pneumatic lock, central locking system signal output time is 3.5S(JP6
short circuit will be on 3.5S position)

Code Learning:
How le laming code , please do he ful lowing slog

1. Keep pressing the footbrake

2. Then un the key farm OFF to ADC 8 tames, he faith lighted on, the system ender he laming code mode
3. Them presa any button date traramitera, the saran harp acne fast light off, that means code leaning for the frat
taramite s successful you want o learning cade the mere traramitera sleeve repeat he above operational from
step 1

Notice: you can learn 4 transmitters at most. (Each time you can only learning code one transmitter) SPY BLE
ALARM APP User Manual

1. APP Download OS platform and Android platform can be downloaded through QR code scanning Download
QR code
 IOS platform can enter the “App Store” of Apple’s mobile phone and search for “SPY BLE ALARM” to
download.
2. APP Code Learning: After the APP is installed successfully, enter the APP setting interface, press and hold for
1 second or press and hold the Learn Code button, then press the remote control “Lock + Unlock” button
simultaneously for 2 times within 10 seconds, and the code learning is completed.
Note
1. During the APP learning process, the brain unit must be working.
2. After the learning code is completed, please enter the APP home interface to operate the button function.
Confirm whether the APP learning code is successful or not. If not, learning code again.
3. Home interface function:
1. Open the app each time, you will enter the homepage interface by default.
2. License plate number — You can modify the license plate number through the setting interface.
3. Transmit signal indication— Press the home interface button, during the signal transmission process, the
signal icon will become blue.
4. Button functions on the homepage interface; buttons arm and lock; button– unlock and disarm :buttons—
mute, 2 button–car search: Sutton—trunk release.
4. Setting interface
1. Shake your cellphone to lock-When you activate this function, the system will pop up the three options for
shake automatically:
2. Shake your cellphone to arm, and the cell phone will emit a “click” sound. Shake your cellphone to
disarm, and the cell phone will emit a “click” sound 2.0peration sound reminder-When you activate this
function, the phone will emit the sound to corresponding function, when you press the lock/unlock button.
Such as, arm for one sound, disarm for two sounds
3. Code learning button-press and hold the button for 1 second or keep pressing the learning code button,
and press the remote control “Lock Unlock” button simultaneously twice within 10 seconds to finish the
learning code
4. Authorization code The key code of the communication between the APP and the brain unit can be
authorized for the third party by copying. Note: The authorization code cannot be changed at will. After
being changed, the brain unit can not be controlled.
5. License plate number-click to set or modify my license plate number, and synchronize with the home
interfac
6. APP version information-record the latest APP version information.

FOC Caution

This device compiles with part 15 of the FOC Rules. Operation is subject to the following two conditions:

1. This device may not cause hammed interference, and

2. This device must accept any interference received including interference that may cause undesired operation.
515.21

Changes or modification waning Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment 515.105 Information to the user. Note:
 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These its are designed to provide reasonable protection against harmful interference
residential installation This equipment generates uses and can radiate radio frequency energy and, t not installed
and used in accordance with the instructions, may cause hammed interference to radio communications.
However, here is no guarantee that interference will not occur in a particular installation If this equipment does
cause harmful interference to radio or television reception, which can be determined by burning the equipment o
and an, the user is encouraged to try to comet the interference by one or more the following measures:

Reorient or relocate the receiving antenna

Increase the separation between the equipment and receiver.
Cornet the equipment into an outlet on a circuit different from that to which the receiver is connected,
Consult the dealer or an experienced radio TV technicians for hep

TECHINICAL DATA

Working voltage: 3.0

Working current: Central locking system:15mA
Siren: 10mA ;
Flash ghts:1OmA
Trunk:10mA
Window rolling up signal:-250mA;
Flameout signal:-250mA
Static Current: s20mA
Working frequency: 433. 92M2 40OKH2
Working Temperature:-40C +85C

Documents / Resources

SPY LT565 APP Car Alarm System [pdf] User Manual

LT565, SY9-LT565, SY9LT565, LT565 APP Car Alarm System, LT565, APP Car Alarm System,
Car Alarm System App, Car Alarm App

Manuals+, home privacy