FF BALL VALVE FOR WATER CT3371.

0_03
EN
TOTAL PASSAGE - SERIES ARNO® October 2016

PRODUCTION RANGE
LEVER ADJUSTMENT
Code 3371 14NI 3371 38NI 3371 12NI 3371 34NI 3371 10NI 3371 04NI 3371 02NI 3371 20NI 3371 22N 3371 30N 3371 40N
Size 1/4II 3/8II 1/2II 3/4II 1II 1II1/4 1II1/2 2II 2II1/2 3II 4II
PN [bar] 40 25 10

BUTTERFLY ADJUSTMENT
Code 3372 14NI 3372 38NI 3372 12NI 3372 34NI 3372 10NI 3372 04NI
Size 1/4II 3/8II 1/2II 3/4II 1II 1II1/4
PN [bar] 40

CONSTRUCTION FEATURES
Body: Nickel-plated brass Lever or butterfly: Black painted aluminium
Ball: Chrome plated brass Passage: Total - Heavy Series
Seats: PTFE
Threaded connections: FF UNI-EN-ISO 228

TECHNICAL FEATURES
Temp. of use: -20 ÷ +120°C Fluid of use: Water, water + glycol, steam and
Pmax use: refer to that stated in the table hydrocarbons

DIMENSIONAL FEATURES
C D E F G
Code ØA ØB
[mm] [mm] [mm] [mm] [mm]
II
3371 14NI 1/4 8 47 11 48 75 67.5
3371 38NI 3/8II 10 50.5 12 49.5 92 71.5
3371 12NI 1/2II 15 63.5 15 52 92 77.5
3371 34NI 3/4II 20 71 16.3 63 117 93
3371 10NI 1II 25 83 19.1 66 117 100.5
3371 04NI 1II1/4 32 96.5 21.4 71.5 154.5 117.5
3371 02NI 1II1/2 40 106.5 21.4 77 154.5 129
3371 20NI 2II 50 128 25.7 92.5 185 156
3371 22N 2II1/2 65 154 31.5 114.5 229 187
3371 30N 3II 80 180 34.5 141 256 227.5
3371 40N 4II 94 178 29.5 150 229 226

C D E F G
Code ØA ØB
[mm] [mm] [mm] [mm] [mm]
3372 14NI 1/4II 8 47 11 59.5 48 52
3372 38NI 3/8II 10 50.5 12 62.5 49.5 52
3372 12NI 1/2II 15 63.5 15 67.5 51 74
3372 34NI 3/4II 20 71 16.3 82 61 82
3372 10NI 1II 25 83 19.1 89.5 64.5 82
3372 04NI 1II1/4 32 96.5 21.4 102.5 72 82
 FLUID DYNAMICS FEATURES

head loss Pa

Q = Flow rate L/h

Size Kv
(m3/h)
1/4" -
3/8" 5.11
1/2" 15.07
3/4" 25.00
1" 48.33
1"1/4 71.10
1"1/2 116.28
2" 210.00
2"1/2 -
3" -
4" -

VALVE INSTALLATION
a) We recommend installing the valve using suitable tools only;
b) We recommend installing and tightening the valve using only the sleeve that is in contact with the pipe thread.

SAFETY REGULATIONS AND FIELD OF APPLICATION

a) Before every installation, check the maximum pressure limit stated on the valve body, referring to the operating temperature at 20 °C.
Example: PN 40, max. pressure 40 bar for water, hazardous and non-hazardous fluids;
b) The fluid passing through the valve must not contain suspended solids, soiling and/or abrasive substances, that are not compatible with
copper and alloys;
c) No maintenance is required on the valve;
d) Position the valve shutter (ball) only in closing or in opening. We recommend partial opening or closing;
e) With the use of water and/or liquids in general, the operating temperature must not drop below their freezing point.

RBM spa reserves the right to improve and change the described products and related technical data at

 any moment and without prior notice: always refer to the instructions attached with the supplied
components; this sheet is an aid, should the instructions be extremely schematic.
Our technical department is always at your disposal for any doubt, problem or clarification.
RBM Spa
Via S.Giuseppe, 1
25075 Nave (Brescia) Italy
Tel. 030-2537211 Fax 030-2531798
E-mail: [email protected] – www.rbm.eu

Technical Sheet CT3371.0-EN_03 RBM Page 2 of 2