AMOLED

SPECIFICATION

Part Number USMP-A055-108192CDX-A0

Size 5.5"
Resolution 1080 x 1920
Brightness 350 cd/m²
Contrast 10000:1
Viewing Angle 85/85/85/85
Operating Temp. -20 ~ 60℃

FOR ADDITIONAL INFORMATION

PLEASE CONTACT:
engineering@[Link]

Issue Date Approved by (customer use) Checked by Prepared by

(800) 741-7755
PROPRIETARY NOTE: THIS SPECIFICATION IS THE PROPERTY OF US MICRO PRODUCTS
AND SHALL NOT BE REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF
US MICRO PRODUCTS AND MUST BE RETURNED TO US MICRO PRODUCTS UPON ITS [Link]
REQUEST.

- CONFIDENTIAL -
 RECORDS OF REVISION
[Link]
DATE PARAGRAPH REVISED No. SUMMARY REMARK
DRAWING No.
2017/5/17 ALL 0.0 FIRST ISSUE
Modify Pin Function
2018/1/18 12 0.1
Description
2018/6/13 8 0.2 Add the current
Add power operating
2018/6/15 8-9 0.3
sequence

[Link] 2 +1 (800) 741-7755

 Contents

1 Introduction----------------------------------------------- 4

2 General specification------------------------------------- 5

3 Mechanical drawing-------------------------------------- 6

4 Absolute maximum ratings------------------------------ 7

5 Electrical characteristics---------------------------------- 7-9

6 Optical characteristics ------------------------------------ 10-13

7 MIPI Interface Pin function ----------------------------- 14

8 Block diagram --------------------------------------------- 15

9 Caution ------------------------------------------------------ 16

10 AMOLED quality criteria--------------------------------------- 17-20

11 Reliability Test -------------------------------------------- 21

12 Precautions for using AMOLED modules ----------------------- 22-23

13 Packing method-------------------------------------------- 24

[Link] 3 +1 (800) 741-7755

1. Introduction
1.1 Scope of application
This specification applies to the AMOLED module that is supplied by USMP. This
AMOLED module should be designed for mobile phone use.

AMOLED specification: Duty 1/1920, Dots 1080xRGBx1920

As to basic specification of the driver IC, refer to the IC (Raydium:RM67191)
specification and datasheet.
All material & processing of the AMOLED module should be USMP Free.

1.2 TFT features:

Structure: AMOLED PANNEL+IC+FPC+TP FPC
MIPI interface

1.3 Applications:
Mobile phone

[Link] 4 +1 (800) 741-7755

2. AMOLED General specification

ITEM AMOLED UNIT

Number of Dots 1080*(RGB)*1920 Dots
Pixel Size (H*V) 31.62*63.24 μm
Active Area 68.299*121.421 mm
Glass Area (W*H) 70.66*128.36 mm
Driver IC RM67191 --
Touch IC S3508
Weight TBD

[Link] 5 +1 (800) 741-7755

[Link] 6 +1 (800) 741-7755
4. ABSOLUTE MAXIMUM RATINGS

Parameter Symbol Min Max Unit

Analog/boost power voltage VCI -0.3 5.28 V
VCI I/O voltage VCI_IF -0.3 5.28 V
I/O voltage VDDIO -0.3 3.96 V
VSP voltage VSP - 6.5 V
VPP(OTP power) VPP - 8.64 V
TP Power voltage VDD3 -0.3 3.6 V
TP I/O Digital Voltage IOVCC 1.8 3.6 V
Operating temperature Top -20 60 C
Storage temperature Tstg -30 70 C

5. ELECTRICAL CHARACTERISTICS
Item Symbol Min Typ Max Unit
AMOLED Power positive ELVDD - 4.6 - V
AMOLED power Negative ELVSS - -2.5 - V
Gamma Voltage VSP 6.1 6.4 6.5 V
VDDIO 1.65 1.8 3.6 V
Analog Power supply
VCI 2.5 3.3 4.8 V
TP Supply voltage VDD3 2.8 - 3.6 V
VIH 0.7*IOVCC - IOVCC V
TP Logic Input Voltage
VIL -0.3 - 0.3*IOVCC V
VOH 0.7*IOVCC - - V
TP Logic Input Voltage
VOL - - 0.3*IOVCC V

[Link] 7 +1 (800) 741-7755

 Mode Symbol Condition Min. Typ. Max. Unit Remark
IELVDD/ELVSS VELVDD=4.6V - 210 275 mA -
VELVSS=-2.5V
IVCI - 2 3 mA -
VCI=3.3V
Full White IVDDIO - 50 65 mA -
VDDIO=1.8V
@350 Nits
VSP=6.4V
IVSP @ Full white - 17 150 mA -
350 nits
TP Normal
Iopr 16 mA -
Operation
AVDD=3.3V
TP Monitor Imon 0.6 mA -
TP Sleep Islp 40 uA -

5.2 Recommended Operating Sequence

5.2.1 Power on sequence

[Link] 8 +1 (800) 741-7755

 5.1.2 Power off sequence

[Link] 9 +1 (800) 741-7755

6. AMOLED Optical Characteristics

SPECIFICATION
SYMB CONDITION S UNI
ITEM OL S
NOTE
MIN TYP. MA T
. X
2
Brightness B 300 350 - cd/m
Contrast Ratio CR 8,000 10,000 - --
Response Time Tr+Tf - - 2 ms
Red XR /
YR Viewing /
Green XG normal angle /
CIE All left side
YG /
Color data are based
Blue XB /
coordinate on USMP’s
YB /
product
White XW 0.27 0.30 0.33 reference only
YW 0.29 0.32 0.35
Hor. X / 85 -
Viewing X Center / 85 -
Deg.
Angle Ver. Y  CR>=1000 / 85 -
Y  / 85 -
Color Gamut NTSC 80 100 - %
Uniformity Un 70 - - %

[Link] 10 +1 (800) 741-7755

Note 2: Definition of contrast ratio CR:

Note 3: Definition of response time (TR, TF)

[Link] 11 +1 (800) 741-7755

 R F

[Link] 12 +1 (800) 741-7755

[Link] 13 +1 (800) 741-7755
7. LCM MCU Interface Pin Function
# Pin_name I/O Description
1 ELVDD Power AMOLED power Positive
2 ELVSS Power AMOLED power Negative
3 ELVDD Power AMOLED power Positive
4 ELVSS Power AMOLED power Negative
5 ELVDD Power AMOLED power Positive
6 ELVSS Power AMOLED power Negative
Power supply for OTP.
7 VPP Power
Leave the pin to open when not in use.
8 GND Power The power ground
9 ID O Connect to Mainboard ID, default High
10 D2P I MIPI DSI data2+
11 TSP_AVDD I Analog Power for TSP
12 D2N I MIPI DSI data2-
13 TSP_SDA I/O Serial interface Data for TSP
14 GND Power The power ground
15 TSP_SCL I/O Serial interface Clock for TSP
16 D1P I MIPI DSI data1+
17 TE O Tear effect output
18 D1N I MIPI DSI data1-
19 TSP_ATTN I State change interrupt for TSP
20 GND Power The power ground
21 TSP_RESET I Active low，Reset the Touch IC
22 CLKP I MIPI DSI clock+
23 OLED_EN O Enable VSP(VLIN) for DC/DC IC
24 CLKN I MIPI DSI clock -
25 SWIRE O Enable ELVDD and ELVSS of DC/DC IC
26 GND Power The power ground
27 GND Power The power ground
28 D0P I MIPI DSI data0+
29 VDDI I Driver IC digital I/O supply
30 D0N I MIPI DSI data0-
31 VSP I Charge pumping Power for Driver IC
32 GND Power The power ground
33 VCI I Driver IC analog supply
34 D3P I MIPI DSI data3+
This signal will reset the device and must be applied to
35 RSTB I
properly initialize the chip. Active low.
36 D3N I MIPI DSI data3-
37 GND Power The power ground
38 GND Power The power ground
39 ERR_FG O MIPI error flag monitor，open it if not use
40 NC - No connection
[Link] 14 +1 (800) 741-7755
[Link] Block Diagram

RESET RESET

IOVCC IOVCC

VCI VCI

VSP VSP

AVDD AVDD

AVEE AVEE

GND GND

DSI_D0P / DSI_D0N DSI_D0P / DSI_D0N

MIPI DSI
DSI_D1P /DSI_D1N DSI_D1P /DSI_D1N

DSI_D2P /DSI_D2N DSI_D2P /DSI_D2N

DSI_D3P /DSI_D3N DSI_D3P /DSI_D3N

DSI_CP/ DSI_CN DSI_CP/ DSI_CN

[Link] 15 +1 (800) 741-7755

9. Caution

9.1 Handling of AMOLED

. Be sure to ground the body when handling the AMOLED.
. Don’t give external shock
. Don’t apply excessive force on the surface.
. Liquid in AMOLED is hazardous substance. Must not lick and swallow.
When the liquid is attach to your hand, skin, cloth etc. Wash it out
thoroughly and immediately.
. Don’t operate it above the absolute maximum rating.
. Don’t disassemble the AMOLED

9.2 Storage
.Store in an ambient temperature of 5℃ to 45℃,and in a relative humidity
of 40% to 60%. Don’t expose to sunlight or intensive ultraviolet rays
. Storage in a clean environment, free from dust, active gas, and solvent.
. Store in anti-static electricity container.
. Store without any physical load.

[Link] 16 +1 (800) 741-7755

[Link] Quality Criteria
[Link]/描述
These inspection standars shall be applied to OLED Module supplied by USMP.
此份检验标准适用于USMP提供之成品的出货检验。

[Link] 17 +1 (800) 741-7755

[Link] 18 +1 (800) 741-7755
[Link] 19 +1 (800) 741-7755
[Link] 20 +1 (800) 741-7755
11. RELIABILITY TEST
NO ITEM CONDTTION STANDARD

1 High Temp. Storage 80℃, 24 hours 1. Functional test is

OK.
2 Low Temp. Storage -30℃, 24 hours Missing Segment,
short, unclear
3 High Temp. Operation 60℃, 16 hours
segment, non-display,
4 Low Temp. Operation -20℃, 16 hours display abnormally
and liquid crystal leak
High temperature and
are un-allowed.
5 high 55℃,90~95%RH ,48 hours
2. No low
Humidity storage
temperature bubbles,
Static state， -30℃（1 hour）~80℃ end seal loose and
Thermal and cold
6 （1 hour）~ -30℃（1 hour）， fall, frame rainbow.
shock
packaging，10 cycles
Packaging，Frequency : 10-55Hz 1. Function test is
Amplitude : 1.0mm， OK.
7 Vibration test 2. No glass crack,
Each direction on X,Y axe 0.5 hour，
circle 2 hours chipped glass, end
seal loose and fall,
epoxy frame crack
Pack products into the carton box. and so on.
8 Dropping test Drop it from 80cm height to ground. 3. No structure loose
Once for each side of the carton and fall.

NOTE：
11.1.1 The reliability items will be fully performed in new sample qualification,
11.1.2 The reliability status will be tested as monitor during mass production. Individual reliability
test shall be
performed by lot , Moreover, the individual reliability item shall be decided according to
reliability plan.
11.1.3 All samples are inspected after keeping in the room with normal temperature and humidity for
2 hours or above.
11.1.4 Vibration test: It is not necessary to test for those products without assembly frame , back
light ,PCB and so on.
11.1.5 Dropping test : It is necessary for affirming new package.
11.1.6 For the high temperature and high humidity test, pure water of over 10 MΩ.cm should be
used.
11.1.7 Each test item applies for test LCM only once .Then tested LCM cannot be used again in any
other test item.
11.1.8 The quantity of LCM examination for each test item is 5pcs to 10pcs.

[Link] 21 +1 (800) 741-7755

12. PRECAUTIONS FOR USING LCM MODULES

12.1 Safetv instructions

12.1.1 If the LCD panel breaks, be careful not to get any liquid crystal substance in your mouth.
12.1.2 If the liquid crystal substance touches your skin or clothes, please wash it off immediately by
using soap and water.
12.2 Handling Precautions
12.2.1 Avoid static electricity damaging the LSI.
12.2.2 Do not remove the panel or frame from the module .
12.2.3 The polarizing plate of the display is very fragile . So, please handle it very carefully.
12.2.4 Do not wipe the polarizing plate with a dry cloth, as it may easily scratch the surface of the
plate.
12.2.5 The color tone of display and background of LCM has the possibility to be changed in the
storage temperature range.
12.2.6 Pay attention to the working environment, as the element may be destroyed by static electricity.
--Be sure to ground human body and electric appliance during work.
--Avoid working in a dry environment to minimize the generations of static electricity.
--Static electricity may be generated when the protective film is fast peeled off.
12.2.7 When soldering the terminal of LCM, make certain the AC power source of soldering iron
does not leak.
12.2.8 If the display surface becomes contaminated ,breathe on the surface and gently wipe it with a
soft-dry- clean cloth .If it is heavily contaminated ,moisten cloth with the following
solvent(ex:Ethyl alcohol).Solvents other than those above-mentioned may damage the
polarizer(Especially ,do not use them .ex: Warter / Ketone)

12.3 Operation instructions

12.3.1 It is recommended to drive the LCD within the specified voltage limits, try to adjust the
operating voltage for the optimal contrast, the color and contrast of LCD panel will varies at
different temperature.
12.3.2 Response time is greatly delayed at low operating temperature range. However, this does not
mean the LCD will be out of the order, It will recover when it returns to the specified temperature
range.
12.3.3 If the display area is pushed hard during operation, the display will become abnormal.
12.3.4 Do not operate the LCD at the environments over the specified conditions, this may cause
damage on the LCD and shorten the lifetime.

12.4 Storage instructions:

12.4.1 Store LCDs in a sealed polyethylene bag.
12.4.2 Store LCDs in a dark place, Do not expose to sunlight or fluorescent light. Keep the
temperature between 0℃and 35℃.
12.4.3 Avoid the polarizer touch any other object, ( It is recommended to store them in the container in
which they were shipped.)

12.5 Limited Warranty

12.5.1 USMP will replace or repair any of its LCD modules, which are found to be defective, when
inspected in accordance with USMP LCM acceptance standards ( copies available upon request )
for a period of 12 months from ink- print date on product

[Link] 22 +1 (800) 741-7755

12.5.2 Any defects must be returned to USMP within 60 days since ship-out. Confirmation of such
date shall be based on freight documents. The warranty liability of USMP limited to repair and/or
replacement on defects above (7.1,7.2)
12.5.3 No warranty can be granted if the precautions stated above have been disregarded. The typical
samples are as below:
-- LCD glass crack/break
--PCB outlet is damaged or modified.
--PCB conductors damaged.
--Circuit modified with by grinding, engraving or painting varnish.
--FPC crack
12.5.4 Modules must be returned with sufficient description of the failures of defects. Any connectors

or cable installed by the customer must be removed completely without damaging the PCB outlet,

conductors and terminals. Modules must be packed with the container in which they were

shipped.

[Link] 23 +1 (800) 741-7755

13. Packing method------TBD

[Link] 24 +1 (800) 741-7755