Technical Data Architecture Coatings
Royale Luxury Matt Emulsion
Product Description
A premium quality acrylic polymer latex pigmented with titanium dioxide and other high
grade light fast and alkali resisting pigments. It has excellent scrub resistance and
washability. It is resistant to fungus and algae, and is an ideal matt topcoat for interior.
Recommended Areas of Application
Area of Use : Interior
Substrate : Concrete, Plaster, Masonry, Gypsum,Timber.
Technical Data
Sheen Variants : Matt, Smooth
Colours : As per shade card and available in various shades through
Colour World machine.
Volume Solids : 44% ± 2%
Pack Size : 1 Ltr, 3.6 Ltr, 18 Ltr
Recommended Dry Film Theoretical
Thickness per coat Spread rate m²/ ltr
Theoretical Covering Capacity Minimum 30 microns 14.6 m²/Ltr
Maximum 50 microns 8.8 m²/Ltr
Typical 40 microns 11 m²/Ltr
Practical Covering Capacity : For estimation of practical covering capacity, following
factors to be taken into account: surface profile, uneven
application, over spray, losses in container and equipment etc.
Substrate Re coating Interval
Temperature Touch Dry
Minimum Maximum
Drying time 25°C 6 hours 12 Hours Indefinite
35°C 3 hours 8 Hours Indefinite
45°C 1.5 hour 4 Hours Indefinite
Additional Data
Method of application : Brush, roller or spray application
Thinner : Sweet water
Thinning ratio (by vol.) : Use 5% to 10% for ease of application depending on the
method of application
Surface Preparation
The performance of this coating is directly related to the degree of surface preparation.
• Ensure surface is clean, dry and free from all contaminants.
• Surface must be sound and free from laitance.
• Remove laitance by wire brush or sweep blast.
Note: Fungal growth should be treated with Antimicrobial solution as recommended by Asian
Paints. After drying, one coat of plastaseal penetrating sealer can be applied if required.
Application Details
• Ensure adequate ventilation during application and drying.
• Do not apply when humidity exceeds 85% and condensation is likely.
• Surface temperature should be 3°C or more above dew point.
• Stir the contents thoroughly before and during use, with a broad flat stirrer, using an upward
lifting action.
Brush or Roller : Apply an even coat taking care to avoid runs and sags.
Minimum two coats recommended.
Conventional Spray : Use normal spray equipment.
Airless Spray : May also be used.
TYPICAL PAINT SYSTEM
1 Coat x AR Primer/PVA Primer /As recommended by the Company
2 Coats x Stucco/As recommended by the Company
2 Coats x Royale Luxury Matt Emulsion
For alternate system suggestion please contact Sales Representative
Storage, Safety Information And Precautions
Safety Precautions
• Keep out of reach of children.
• Store in cool, dry conditions; ensure adequate ventilation during application.
• Avoid contact with skin and eyes; wear suitable protective clothing such as overalls, goggles,
dust masks and gloves.
• Shelf life up to 24 month is from the date of manufacture.
First-Aid
• Eyes : In the event of accidental splashes, flush eyes with water immediately and obtain
medical advice.
• Skin : Wash skin thoroughly with soap and water or approved industrial cleaner. Do not use
solvent or thinners.
• Inhalation : Move patient to fresh air, loosen collar and keep patient rested.
• Ingestion : In case of accidental ingestion, do not induce vomiting. Obtain immediate medical
attention.
Disclaimer
The information provided in this data sheet is not intended to be complete. It is the responsibility of the user to ensure that the product used is suitable for the
purpose it is meant to serve. In view of various factors affecting the performance of the coating, we cannot assume responsibility for the product performance, nor do
we accept any liability arising from use of this product, unless specifically agreed to in writing by us. The information provided in the data sheet may be modified by us
without notice.
This Technical Data Sheet supersedes those previously issued with immediate effect
Version No: 12/2019
