MCX 912 / 913 Parameter Collection Form

Tool Version 1.0

Protocol Data Revision No 0
Customer and plant information
Customer name
Substation designation
Bay designation ###
ABB order number

Parameter collection information

Collection Date Substa
Collected by Bay de
Company ABB o
Department Collec
Phone number Collec
E-mail address Collec

Relay data
Relay type designation #VALUE! Collec
Relay serial number Collec
Relay type Relay
Relay rated current INR A
Relay rated frequency Hz
Relay auxiliary supply voltage Relay

Current transformer data

CT primary rated current A
CT ratio KI Relay rated current missing CT pri

Io current transformer data CT rat

Io is a Io current transformer present? Io Is a
Io CT primary rated current A
Io CT ratio KIo Io CT

MCX-Relay setting values

Setting current Mode 00 IE INR

Short circuit protection I>> Instance: 1 Mode_

I>>1 Short circuit protection Mode 01 I>>1 IE
I>>1 Time lag Mode 02 tI>>1 s

Overcurrent protection I> Instance: 1 Mode_

I>1 Overcurrent protection Mode 03 I>1 IE
I>1 Time lag Mode 04 tI>1 s

Negative phase sequence protection Mode_

NPS protection Mode 05 I2 IE
NPS Time lag Mode 06 tI2 s

Page 1 of 3 fill in this form

Earth fault protection Mode_
Io Earth fault protection Mode 07 Io IE
Io Time lag Mode 08 tIo s
Io INT / EXT Mode 09 ###
Io C.t. ratio Mode 10 k ###

Locked rotor protection Mode_

IblR Locked rotor protection Mode 11 Ibl.R. IE
IblR Time lag Mode 12 tbl.R. s

Motor starting protection Mode_

Istart Starting protection Mode 13 Istart IE
Istart I²T permitted for start Mode 14 I²Tstart IE2 s

Protection against low load Mode_

I< Protection against low load Mode 15 I< IE
I< Time lag Mode 16 tI< s

Protection against too many motor starts ###

Motor start-up time tstart s
Number of motor starts from cold Mode 17 Ncold ###
Number of motor starts from warm state Mode 18 Nwarm ###
Time for N=N-1 Mode 19 tN-1 s
Mode 20 Mode_
Temperature rise DJ3 Mode 20 DJ3 %
Start with overheating Mode 21 NS ###

Thermal overload protection Mode_

Temperature rise DJ1 Mode 30 DJ1 %
Temperature rise DJ2 Mode 31 DJ2 %
Reset for DJ2 Mode 32 HDJ %
Heating time constant Mode 33 t­ min
Cooling time constant Mode 34 t¯ min
DJ0 automatic Mode 38 DJ0 %
DJ0 manual Mode 39 DJ0 %

Measurement mean value setting

Time setting for measurement mean values Mode 40 kTE Mode_

Short circuit protection I>> Instance: 2 Mode_

I>>2 Short circuit protection Mode 41 I>>2 IE
I>>2 Time lag Mode 42 tI>>2 s

Overcurrent protection I> Instance: 2 ###

I>2 Overcurrent protection Mode 43 I>2 IE
I>2 Time lag Mode 44 tI>2 s

Overcurrent protection I> Instance: 3 Mode_

I>3 Overcurrent protection Mode 45 I>3 IE
I>3 Time lag Mode 46 tI>3 s

Put protection function groups out of action

Function selection Mode 47 CTRL 1 IE

Page 2 of 3 fill in this form

Tripping matrix settings
Digit 3
MR I
Digit 2
MR II
Digit 1
AR I
Digit 0
AR II
Mode_
I>>1 Short circuit protection Mode 101 I>>1 ###
I>1 Overcurrent protection Mode 103 I>1 ###
NPS protection Mode 105 I2 ###
Io Earth·fault protection Mode 107 Io ###
IblR Locked rotor protection Mode 111 Ibl.R. ###
Istart Starting protection Mode 113 Istart ###
I< Protection against low load Mode 115 I< ###
Number of motor starts from cold or warm Mode 117 Ncold, Nwarm ###
Temperature rise DJ3 Mode 120 DJ3 ###
Temperature rise DJ1 (Warn), DJ2 (Trip) Mode 130 DJ1,DJ2 ###
I>>2 Short circuit protection Mode 141 I>>2 ###
I>2 Overcurrent protection Mode 143 I>2 ###
I>3 Overcurrent protection Mode 145 I>3 ###
Jumper S4
(General blocking setting for selective relay or complete protection relay)
Jumper S4 position Mode_

Switch S65 state (Settings for selective relay blocking)

S65 switch 1 signalling relay MRI Mode_
S65 switch 2 signalling relay MRII ###
S65 switch 3 tripping relay ARI ###
S65 switch 4 tripping relay ARII Mode_

Page 3 of 3 fill in this form