05

Spare Parts Catalog Doc. no. R 223.1526

SANDVIK CH660:06
SANDVIK CH660:06

© Copyright 2021 Sandvik SRP AB.

All rights reserved. No parts of this document may be reproduced or copied in any form or by
any means without written permission from Sandvik SRP AB. All data and information in this
manual may be changed without further notice. Reservations for misprints.

Document number: R 223.1526

Issue: 2023-03-31
Version: 05

Document type: Spare Parts Catalog (SPC)

Sandvik
Stationsplan, SE-233 81 Svedala, Sweden
Tel: +46 (0)40 409000, Fax: +46 (0)40 409260
www.sandvik.com
SPC Sandvik CH660:06

General 11

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Cone crusher 15

Cone crusher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

1. Feed hopper 17

1a. Feed hopper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

1b. Feed hopper, upper, lining kit . . . . . . . . . . . . . . . . . . . . . . 19

1c. Rubber lining kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

1d. Rubber lining kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

1e. Cone alternatives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

1f. MC cone kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

(Continued)1g. C and CX cone kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

(Continued)1h. EC cone kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

(Continued)1i. Feed distributor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

2. Top shell 31

2a. Top shell excluding concave . . . . . . . . . . . . . . . . . . . . . . 32

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 3

SPC Sandvik CH660:06

(Continued)2b. Top shell including concave . . . . . . . . . . . . . . . . . . . . . 34

(Continued)2c. Fastener kit for concave and support ring . . . . . . . . . . 36

(Continued)2d. Fasteners for top shell . . . . . . . . . . . . . . . . . . . . . . . . . . 37

(Continued)2e. Concave alternatives . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

(Continued)2f. Filler ring alternatives . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

(Continued)2g. Temperature transmitter alternatives . . . . . . . . . . . . . . 40

(Continued)2h. Spider bushing temperature transmitter . . . . . . . . . . . 41

(Continued)2i. Concave kit without support ring . . . . . . . . . . . . . . . . . . 42

(Continued)2j. Concave alternatives (without support ring) . . . . . . . . . 43

(Continued)2k. Spider cap kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

3. Main shaft 45

3a. Main shaft excluding mantle . . . . . . . . . . . . . . . . . . . . . . 46

(Continued)3b. Main shaft including mantle . . . . . . . . . . . . . . . . . . . . . . 48

(Continued)3c. Head nut with burning ring . . . . . . . . . . . . . . . . . . . . . . . 50

(Continued)3d. Mantle alternatives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

4. Dust collar 53

4a. Dust collar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

4 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06

4b. Locating bar kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

5. Eccentric 57

5a. Eccentric AM assembly, throw 18-20-24-28 . . . . . . . . . . . 58

(Continued)5b. Eccentric AM assembly, throw 28-32-36-40 . . . . . . . . . 60

(Continued)5c. Eccentric AM assembly, throw 40-44-48-50 . . . . . . . . . . 62

(Continued)5d. Eccentric bushing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

(Continued)5e. Gear and pinion set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

6. Bottom shell 67

6a. Bottom shell with rubber liners (standard) . . . . . . . . . . . 68

(Continued)6b. Bottom shell with steel wear plates liners (option) . . . 70

(Continued)6c. Foot assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

(Continued)6d. Rubber lining bottom shell . . . . . . . . . . . . . . . . . . . . . . . 73

(Continued)6e. Rubber lining kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

(Continued)6f. Steel wear plate lining bottom shell . . . . . . . . . . . . . . . . 75

(Continued)6g. Bolt set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

(Continued)6h. Arm liners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

(Continued)6i. Temperature transmitter alternatives . . . . . . . . . . . . . . . 78

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 5

SPC Sandvik CH660:06

7. Hydroset cylinder 79

7a. Hydroset cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

(Continued)7b. Piston . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

(Continued)7c. Step bearing set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

(Continued)7d. Chevron packing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

(Continued)7e. Position transmitter alternatives . . . . . . . . . . . . . . . . . . 85

(Continued)7f. Position transmitter plug . . . . . . . . . . . . . . . . . . . . . . . . . 86

(Continued)7g. Position transmitter assembly ASRi . . . . . . . . . . . . . . . 87

(Continued)7h. Hydroset protection alternatives . . . . . . . . . . . . . . . . . . 88

(Continued)7i. Hydroset protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

(Continued)7j. Hydroset protection screws . . . . . . . . . . . . . . . . . . . . . . 90

8. Hydroset system 91

8a. Hydroset system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

(Continued)8b. Check valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

(Continued)8c. Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

(Continued)8d. Pressure transmitter alternatives . . . . . . . . . . . . . . . . . 96

(Continued)8e. Accumulator alternative . . . . . . . . . . . . . . . . . . . . . . . . . 97

6 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06

9. Pinion shaft housing assembly 99

9a. Pinion shaft housing aftermarket assembly . . . . . . . . . 100

(Continued)9b. Fasteners and gaskets for pinion shaft housing . . . . 102

(Continued)9c. Pinion shaft housing repair kit . . . . . . . . . . . . . . . . . . . 103

10. Hoses 105

10a. Hoses assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

10b. Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

10c. Adapter kit alternative . . . . . . . . . . . . . . . . . . . . . . . . . . 107

10d. Adapter kit BSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

10e. Adapter kit JIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

11. Dust seal air pressure unit 111

11a. Dust seal air pressure assembly . . . . . . . . . . . . . . . . . 112

11b. Dust seal air pressure unit . . . . . . . . . . . . . . . . . . . . . . 113

11c. Dust seal air pressure fan . . . . . . . . . . . . . . . . . . . . . . . 114

11d. Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115

11e. Dust seal air pressure connection . . . . . . . . . . . . . . . . 116

12. Drive 117

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 7
SPC Sandvik CH660:06

12a. V-belt drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118

(Continued)12b. Sub frame assembly . . . . . . . . . . . . . . . . . . . . . . . . . . 120

(Continued)12c. Motor bracket assembly . . . . . . . . . . . . . . . . . . . . . . . 122

(Continued)12d. Motor alternatives . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123

(Continued)12e. Drive alternatives . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124

(Continued)12f. V-belt drive SPC 50 Hz 4-pole . . . . . . . . . . . . . . . . . . . 125

(Continued)12g. V-belt drive SPC 60 Hz 4-pole . . . . . . . . . . . . . . . . . . 126

(Continued)12h. V-belt drive 8V 60 Hz 4-pole . . . . . . . . . . . . . . . . . . . . 127

(Continued)12i. Spacer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128

(Continued)12j. V-belt cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129

(Continued)12k. Vibration damper, large . . . . . . . . . . . . . . . . . . . . . . . 130

(Continued)12l. Vibration damper, SAW 200 A . . . . . . . . . . . . . . . . . . . 131

13. Sign board 133

13a. Sign board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134

(Continued)13b. Warning sign alternatives . . . . . . . . . . . . . . . . . . . . . . 136

14. Tool kit 137

14a. Tool box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138

8 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06

14b. Cover kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139

14c. Hydraulic pump unit and quick coupling . . . . . . . . . . 140

15. Crushing chamber alternatives 143

15a. Crushing chamber alternatives . . . . . . . . . . . . . . . . . . 144

16. Recommended spare parts 153

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 9

SPC Sandvik CH660:06

10 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06

General

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 11

SPC Sandvik CH660:06

General
Ordering information
When ordering parts, always state the machine type, manufacturing number,
serial number and order number according to the identification plate on the
cone crusher or tank. State quantity, article number and denomination for
each ordered part. The quantities listed in this catalog show how many pieces
of each part that are usually exchanged in a certain position.
Crusher’s identification plate
The figure below shows an example of the crusher’s identification plate. The
identification plate contains data needed when contacting Sandvik
concerning wear parts.
The “Type” designation is part of an identification system that describes the
product.

7
9
1
10
2
3 4 5 6 8

CH660:04-M/B/M/50-36/40/32/28

10 11 12 13 14 15 16
Identification plate Type:
1 Type 11 Type and size of crusher
2 Serial number 12 Development step
3 Local manufacturing number 13 Crushing chamber (concave ring)
4 Order number 14 Mantle
5 Mass (kg) 15 Filler ring (if used)
6 Country of origin 16 Gear set: 50/60 Hz
7 Manufacturer 17 Eccentric throw (mm), first digit = factory setting
8 Year of manufacture
9 CE Mark
10 EAC logo

(Continued)

12 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06

(Continued)
Think ahead!
Avoid unnecessary downtime and increased freight charges by ordering parts
well in advance.
Feedback
If you have comments on this Spare Parts Catalog or problems connected to
the crusher’s documentation, send an e-mail to: [email protected]

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 13

SPC Sandvik CH660:06

This page is intentionally left blank

14 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06

Cone crusher

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 15

SPC Sandvik CH660:06

Cone crusher

3
2
4
6
5
8 9
10

Pos. No. Description Remarks

1 Feed hopper See section 1. Feed hopper.
2 Top shell assembly See section 2. Top shell.
3 Main shaft assembly See section 3. Main shaft.
4 Dust collar assembly See section 4. Dust collar.
5 Eccentric assembly See section 5. Eccentric.
6 Bottom shell assembly See section 6. Bottom shell.
7 Hydroset cylinder assembly See section 7. Hydroset cylinder.
8 Hydroset system See section 8. Hydroset system.
9 Pinion shaft housing assembly See section 8. Hydroset system.
10 Hoses See section 10. Hoses.
11 Dust seal air pressure unit See section 11. Dust seal air pressure unit.
12 Drive alternatives See section 12. Drive.
13 Sign board See section 13. Sign board.
14 Tool kit See section 14. Tool kit.
15 Crushing chamber alternatives See section 15. Crushing chamber alternatives.
16 Recommended spare parts See section 16. Recommended spare parts.

16 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06

1. Feed hopper

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 17

SPC Sandvik CH660:06 452.4132

1a. Feed hopper

2 5
8, 7, 10, 6
1 4

6, 7, 8 A-A

11

7, 8, 9

A A

Pos. No. Qty. Part No. Alternative Description Remarks

Feed hopper assembly
1 1 452.3877-901 Feed hopper, lower
2 1 452.3878-901 Feed hopper, upper
3 1 891.1895-901 Feed hopper, upper, lining kit See section 1b. Feed hopper, upper, lining
kit
4 1 Yes Cones alternatives See section 1e. Cone alternatives
5 1 452.4306-901 Feed distributor assembly See section 1i. Feed distributor
6 12 840.0070-00 Screw M6S 16×60 8.8 FZB ISO 4017
7 40 847.0016-00 Washer BRB 17×30 HB200 ISO 7089
8 40 845.0215-00 Lock nut ISO 7040 M16 8 FZB
9 16 840.0067-00 Screw M6S 16×45 8.8 ISO 4017
10 12 847.0401-00 Washer 17x40x6 ZP
11 2 650.0327-00 Inspection door

18 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 891.1895

1b. Feed hopper, upper, lining kit

6 1

9, 8, 7, 10

6
2, 11, 3, 4, 5 1

Pos. No. Qty. Part No. Description Remarks

891.1895-901 Feed hopper lining kit Consists of:
1 16 891.1896-901 Feed hopper lining See section 1c. Rubber lining kit
2 32 891.0462-001 Square washer
3 32 847.0147-00 Round washer 13×24 ZP
4 32 845.0030-00 Lock nut M12 8 ZP
5 32 843.1323-00 Carriage bolt M12×40 4.6 ZP
6 2 442.9750-01 Inspection door lining See section 1d. Rubber lining kit
7 8 845.0215-00 Lock nut ISO 7040 M16 8 FZB
8 16 847.0016-00 Washer BRB 17×30 HB200 ISO 7089
9 8 840.0071-00 Screw M6S M16×65 8.8 ISO 4014
10 8 873.1287-00 Rubber plug Ø40×40 mm
11 32 891.0401-001 Rubber plug ø54 × 40 mm

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 19

SPC Sandvik CH660:06 891.2128

1c. Rubber lining kit

2 4
5 3
6 1

Pos. No. Qty. Part No. Description Remarks

891.2128-901 Rubber lining kit Consists of:
1 1 891.1896-901 Feed hopper lining
2 2 891.0462-001 Square washer
3 2 847.0147-00 Washer BRB 13×24 HB200 ISO 7089
4 2 845.0030-00 Lock nut M12 8 FZB ISO 7040
5 2 840.0046-00 Screw M6S 12x35 8.8 ISO 4017
6 2 891.0401-001 Rubber plug Ø 54×40 mm

20 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 891.2129

1d. Rubber lining kit

2
3
1
3
4
5

Pos. No. Qty. Part No. Description Remarks

891.2129-901 Rubber lining kit Consists of:
1 1 442.9750-01 Rubber sheet
2 4 845.0215-00 Lock nut ISO 7040 M16 8 FZB
3 8 847.0016-00 Washer BRB 17×30 HB200 ISO 7089
4 4 840.0070-00 Screw M6S 16x60 8.8 ISO 4014
5 4 873.1287-00 Rubber plug Ø 40×40

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 21

SPC Sandvik CH660:06 452.4197

1e. Cone alternatives

Pos. No. Qty. Part No. Description Remarks

Cone alternatives
452.4213-901 Cone MC Consists of:
1 4 452.4216-901 Cone MC
2 1 891.1908-901 Rubber lining MC kit See section 1f. MC cone kit

452.4212-901 Cone C Consists of:

1 4 452.4214-901 Cone C
2 1 891.1902-901 Rubber lining C and CX kit See section 1g. C and CX cone kit

452.4211-901 Cone EC Consists of:

1 4 452.4202-901 Cone EC
2 1 891.1897-901 Rubber lining EC kit See section 1h. EC cone kit

BG00975710 Cone CX Consists of:

1 4 BG00974893 Cone CX
2 1 891.1902-901 Rubber lining C and CX kit See section 1g. C and CX cone kit

22 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 891.1908

1f. MC cone kit

4 1

5 2

2 3

A (1:5)

Pos. No. Qty. Part No. Alternative Description Remarks

891.1908-901 MC cone kit Consists of:
1 24 891.1909-901 Rubber lining cone MC See section Rubber lining MC cone
kit.
2 96 847.0147-00 Washer BRB 13×24 Hb200 ISO 7089
3 48 845.0030-00 Lock nut M12 8 FZB ISO 7040
4 48 891.0401-001 Rubber plug Ø54×40mm
5 48 840.0047-00 Screw M6S 12×40 8.8 ISO 4017

(Continued)

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 23

SPC Sandvik CH660:06 891.2132

(Continued)
Rubber lining MC cone kit

2
4 3
5
2

Pos. No. Qty. Part No. Alternative Description Remarks

891.2132-901 Rubber lining MC cone kit Consists of:
1 1 891.1909-901 Rubber lining
2 4 847.0147-00 Washer BRB 13×24 Hb200 ISO 7089
3 2 845.0030-00 Lock nut M12 8 FZB ISO 7040
4 2 840.0047-00 Screw M6S 12×40 8.8 ISO 4017
5 2 891.0401-001 Rubber plug Ø54×30

24 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 891.1902

1g. C and CX cone kit

4
2
1

3
A (1:5)
2

Pos. No. Qty. Part No. Alternative Description Remarks

891.1902-901 Rubber lining C and CX kit Consists of:
1 24 891.1903-901 Rubber lining See section Rubber lining C and
CX kit.
2 96 847.0147-00 Washer BRB 13×24 Hb200 ISO 7089
3 48 845.0030-00 Lock nut M12 8 FZB ISO 7040
4 48 891.0401-001 Rubber plug Ø54×40mm
5 48 840.0047-00 Screw M6S 12×40 8.8 ISO 4017

(Continued)

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 25

SPC Sandvik CH660:06 891.2131

(Continued)
Rubber lining C and CX kit

2
4
3
5
2

Pos. No. Qty. Part No. Alternative Description Remarks

891.2131-901 Rubber lining C cone kit Consists of:
1 1 891.1903-901 Rubber lining
2 4 847.0147-00 Washer BRB 13×24 Hb200 ISO 7089
3 2 845.0030-00 Lock nut M12 8 FZB ISO 7040
4 2 840.0047-00 Screw M6S 12×40 8.8 ISO 4017
5 2 891.0401-001 Rubber plug Ø54×30

26 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 891.1897

1h. EC cone kit

5 1

4 2

A (1:5)

Pos. No. Qty. Part No. Alternative Description Remarks

891.1897-901 EC cone kit Consists of:
1 96 847.0147-00 Washer BRB 13×24 Hb200 ISO 7089
2 48 845.0030-00 Lock nut M12 8 FZB ISO 7040
3 24 891.1898-901 Rubber lining cone EC See section Rubber lining EC cone
kit.
4 48 840.0047-00 Screw M6S 12×40 8.8 ISO 4017
5 48 891.0401-001 Rubber plug Ø54×40mm

(Continued)

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 27

SPC Sandvik CH660:06 891.2130

(Continued)
Rubber lining EC cone kit

3
4 2
5 3

Pos. No. Qty. Part No. Alternative Description Remarks

891.2130-901 Rubber lining EC cone kit Consists of:
1 1 891.1898-901 Rubber lining EC cone
2 2 845.0030-00 Lock nut M12 8 FZB ISO 7040
3 4 847.0147-00 Washer BRB 13×24 Hb200 ISO 7089
4 2 840.0047-00 Screw M6S 12×40 8.8 ISO 4017
5 2 891.0401-001 Rubber plug Ø54×30

28 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 452.4306

1i. Feed distributor

4 5 6

11

33 22

Pos. No. Qty. Part No. Alternative Description Remarks

452.4306-901 Feed distributor kit Consists of:
1 1 442.8853-01 Bracket
2 1 442.5621-90 Feed distributor, left
3 1 442.5621-00 Feed distributor, right
4 6 840.0065-00 Screw M6S 16×35 8.8 ISO 4017
5 6 847.0016-00 Washer BRB 17×30 HB200 ISO 7089
6 6 845.0009-00 Nut M6m M16 FZB ISO 4032

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 29

SPC Sandvik CH660:06

This page is intentionally left blank

30 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06

2. Top shell

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 31

SPC Sandvik CH660:06 BG00395488

2a. Top shell excluding concave

12
4
3
E
10 D
9
2 10
7 9 2
8
B
6 11

5
1

A-A

A
A

(Continued)

32 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 BG00395488

(Continued)
Pos. No. Qty. Part No. Description Remarks
BG00395488 Top shell assembly excluding concave Consists of:
1 1 Top shell CH660 Cannot be ordered separately
2 2 442.8812-00 Arm shield CH660
3 2 900.0425-00 Pipe joint GE 10-LR
4 1 452.4153-001 Steel pipe DIN 2391/C-ST 35,4 FZ10x1,5
5 1 914.0093-00 Lubrication nipple AH R 1/4"
1 912.0114-00 Air filter element P10102 R 1/4"
6
1 912.0155-00 Filter element Spare part
7 1 900.0169-00 Hexagon Nipple 1/4 N8
8 1 900.0002-00 Elbow A1 Zn DN8 zinced
9 2 900.1030-00 Adapter RI 1/2"-1/4"
10 2 900.0431-00 Pipe joint GE 15-LR
11 1 452.4195-001 Steel pipe DIN 2391/C-ST 35,4 FZ15x1,5
12 1 900.3275-00 Plug G 1/4-19
Not included in the top shell
Temperature transmitter If necessary, the temperature transmitter must to be ordered separately. See section 2g. Temperature
transmitter alternatives.

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 33

SPC Sandvik CH660:06 BG00395290

2b. Top shell including concave

11 38
12 4
3
E
35 D
14 13 6
2 35 15, 16 10
8 3 2
9
B
7 36

29 30 32
31 B 17

C 37 5
C 1

20 28 18, 19 A-A 33
25, 23, 24, 26 21 22 G

F
G
34
A
A G-G
F-F
F

(Continued)

34 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 BG00395290

(Continued)
Pos. No. Qty. Part No. Description Remarks
BG00395290 Top shell assembly incl. concave Consists of:
1 1 Top shell CH660 Cannot be ordered separately
2 2 442.8812-00 Arm shield CH660
3 2 900.0425-00 Pipe joint GE 10-LR
4 1 452.4153-001 Steel pipe DIN 2391/C-ST 35,4 FZ10x1,5
5 1 914.0093-00 Lubrication nipple AH R 1/4"
6 1 BG01116737 Spider cap kit See section 2k. Spider cap kit
1 912.0114-00 Air filter element P10102 R 1/4"
7
1 912.0155-00 Filter element Spare part
8 1 900.0169-00 Hexagon nipple 1/4 N8
9 1 900.0002-00 Elbow A1 Zn DN8 zinced
10 1 873.1401-00 O-ring 594,1x5,7 NBR 70
11 4 840.0651-00 Screw M6S M20x75 8.8 ZP
12 4 847.0165-00 Washer TBRB 21x37 ZP
13 1 442.8754-01 Spider bushing assembly CH/S 660
14 2 900.1030-00 Adapter RI 1/2"-1/4"
15 6 840.0652-00 Screw M6S M20x90 8.8 ZP
16 6 847.0132-00 Washer, round 21x36 ZP
17 1 442.8755-01 Seal ring CH660/CS660
18 1 Concave CH660 alternatives See section 2e. Concave alternatives
19 2 831.0016-00 Casting compound kg See section 15. Crushing chamber alternatives for
quantities.
20 6 840.1074-00 Screw M6S M30x280 8.8 ZP
21 6 442.8881-01 Washer
22 6 442.8908-01 Hose 31.5-0.6
23 6 442.7252-01 Shim
24 6 442.7252-02 Shim
25 6 442.7252-03 Shim
26 6 442.7252-04 Shim
27 4 442.9415-00 Wear plate CH660 alternatives Only for concave EF
28 6 840.1075-00 Screw M6S M30x380 8.8 ZP
29 6 845.0284-00 Lock nut M30 8 ZP
Fasteners for concave, to
30 6 442.7253-01 Sleeve
support ring and top shell
31 6 442.7271-01 Washer
32 54 863.0058-00 Disc spring 90x46x5
33 1 442.8793-01 Support ring
34 6 442.8290-01 Dowel pin Dowel for support ring
35 2 900.0431-00 Pipe joint GE 15-LR
36 1 452.4195-001 Steel pipe DIN 2391/C-ST 35,4 FZ15x1,5
37 1 Filler ring CH660 alternatives See section 2f. Filler ring alternatives
38 1 900.3275-00 Plug G 1/4-19
Not included in the top shell
Temperature transmitter If necessary, the temperature transmitter must to be ordered separately. See section 2g. Temperature
transmitter alternatives.

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 35

SPC Sandvik CH660:06 452.5793

2c. Fastener kit for concave and support ring

2
3
5
4

Pos. No. Qty. Part No. Description Remarks

452.5793-901 Fastener kit for concave and support ring Consists of:
1 6 840.1075-00 Screw M6S 30×380 8.8
2 6 845.0284-00 Lock nut M30
3 6 442.7253-01 Sleeve
4 6 442.7271-01 Washer
5 54 863.0058-00 Disc spring 90x46x5

36 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06

2d. Fasteners for top shell

5 4

1 2 3 4

Pos. No. Qty. Part No. Description Remarks

1 20 840.1073-00 Screws M6S 42x220 8.8
2 20 845.0322-00 Nut M6M M42 8 FZB Fasteners for top shell
3 20 847.0171-00 Washer BRB 43x80 HB 200
4 24 899.0278-00 Protective cap SW65 2 H20
5 4 442.9530-01 Screw M6S 42x100 Jacking screws

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 37

SPC Sandvik CH660:06 452.4218

2e. Concave alternatives

Pos. No. Qty. Part No. Description Remarks

442.8813-01 Concave ring CH660: EC M1
442.8813-02 Concave ring CH660: EC M2
442.8813-03 Concave ring CH660: EC M7
442.8813-05 Concave ring CH660: EC M9
442.9230-01 Concave ring CH660: CX M1
442.9230-02 Concave ring CH660: CX M2
442.9230-03 Concave ring CH660: CX M7
442.9230-05 Concave ring CH660: CX M9
442.8814-01 Concave ring CH660: C M1
442.8814-02 Concave ring CH660: C M2
442.8814-03 Concave ring CH660: C M7
442.8814-05 Concave ring CH660: C M9
442.8815-01 Concave ring CH660: MC M1
442.8815-02 Concave ring CH660: MC M2
442.8815-03 Concave ring CH660: MC M7
442.8815-05 Concave ring CH660: MC M9
1 1
442.8816-01 Concave ring CH660: M M1
442.8816-02 Concave ring CH660: M M2
442.8816-03 Concave ring CH660: M M7
442.8816-05 Concave ring CH660: M M9
442.8817-01 Concave ring CH660: MF M1
442.8817-02 Concave ring CH660: MF M2
442.8817-03 Concave ring CH660: MF M7
442.8817-05 Concave ring CH660: MF M9
442.8818-01 Concave ring CH660: F M1
442.8818-02 Concave ring CH660: F M2
442.8818-03 Concave ring CH660: F M7
442.8818-05 Concave ring CH660: F M9
452.0832-001 Concave ring CH660: EF M1
452.0832-002 Concave ring CH660: EF M2
452.0832-003 Concave ring CH660: EF M7
452.0832-005 Concave ring CH660: EF M9

38 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 452.4289

2f. Filler ring alternatives

Pos. No. Qty. Part No. Description Remarks

1 1 442.8823-01 Filler ring MC, M
1 1 442.8863-01 Filler ring MF, F

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 39

SPC Sandvik CH660:06 BG00492769

2g. Temperature transmitter alternatives

2 1
2 1

Without ASRi/TIMS With ASRi/TIMS

With ACS

2
44

1
44

Without temperature transmitter With temperature transmitter

- used without ASRi/TIMS - used with ASRi/TIMS
- used with ACS

Pos. No. Qty. Part No. Description Remarks

Temperature transmitter alternatives
1 1 BG00492759 Spider bushing temperature transmitter If necessary, the temperature transmitter must to
CH660 K1-TT2 be ordered separately.
2 1 900.3275-00 Plug G 1/4-19

40 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 BG00492759

2h. Spider bushing temperature transmitter

5
7
6

4
1
2, 3

Pos. No. Qty. Part No. Description Remarks

BG00492759 Spider bushing temperature transmitter Consists of:
CH660 K1-TT2
1 1 290.0058-901 Connection box CBT (TT5)
2 1 900.0654-00 Adapter G 1/2 BxG 1/2 B
3 1 900.2624-00 Nut U6M 1/2"
4 1 900.1030-00 Adapter RI 1/2"-1/4"
5 2 900.0425-00 Pipe joint GE 10-LR
6 1 452.4154-001 Steel pipe DIN 2391/C-ST 35,4 FZ 10x1,5
7 1 191.2376-00 Temperature sensor with 3 m cable

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 41

SPC Sandvik CH660:06 BG00421209

2i. Concave kit without support ring

5, 4, 3 A (1:5) A
6
2, 1

Pos. No. Qty. Part No. Description Remarks

Concave kit CH660 EC, CX Consists of:
1 6 847.0420-00 Spherical washer G35 M30 plain Used together with 452.5793-901, see section 2c.
2 6 847.0251-00 Spherical washer C31 M30 plain Fastener kit for concave and support ring.

3 3 442.7179-01 Locating block

4 3 847.0162-00 Washer BRB 37x68 ZP
5 3 840.0712-00 Screw M6S M36x120 8.8 ZP
6 1 Concave CH660 alternatives See section 2j. Concave alternatives (without sup-
port ring)

42 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 BG00463145

2j. Concave alternatives (without support ring)

Pos. No. Qty. Part No. Description Remarks

BG00420433-01 Concave CH660 CX M1
BG00420433-02 Concave CH660 CX M2
BG00420433-03 Concave CH660 CX M7
BG00420433-05 Concave CH660 CX M9
1 1
BG00420395-01 Concave CH660 EC M1
BG00420395-02 Concave CH660 EC M2
BG00420395-03 Concave CH660 EC M7
BG00420395-05 Concave CH660 EC M9

2k. Spider cap kit BG01116737

Pos. No. Qty. Part No. Description Remarks

1 BG01116737 Spider cap assembly Consists of:
1 1 Spider cap
2 1 900.2970-00 Plug

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 43

SPC Sandvik CH660:06

This page is intentionally left blank

44 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06

3. Main shaft

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 45

SPC Sandvik CH660:06 BG01618707

3a. Main shaft excluding mantle

A A 4 5

8
2 A-A

12
1

6 7

10, 11
9
(Continued)

46 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 BG01618707

(Continued)
Pos. No. Qty. Part No. Description Remarks
BG01618707 Main shaft assembly excluding mantle Consists of:
1 1 Main shaft Cannot be ordered separately
2 1 442.8791-01 Inner head nut
3 1 BG00325390 Main shaft sleeve
4 1 BG00511165 Main shaft cover
5 6 841.0658-00 Screw
6 1 853.0119-00 Pin CP 25x60 m6
7 1 855.0026-00 Retaining ring SgA 100
8 1 899.0504-00 Eye bolt VRS-F-M48 swivel
9 1 BG01616809 Transportation rack, main shaft
10 12 847.0016-00 Washer BRB 17x30 ZP
11 12 840.0067-00 Screw M6S M16x45 8.8 ZP
12 4 885.0249-00 Sign, Centre of gravity

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 47

SPC Sandvik CH660:06 BG00563413

3b. Main shaft including mantle

A A
7 8
6

5
4
A-A
3
2
18

10 11
14, 15 9 13
12
1
21

16 17

15, 20
19
(Continued)

48 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 BG00563413

(Continued)
Pos. No. Qty. Part No. Description Remarks
BG00563413 Main shaft Assembly including mantle Consists of:
1 1 Main shaft Cannot be ordered separately
2 1 Mantle alternatives See section 3d. Mantle alternatives.
3 1 831.0016-00 Casting compound kg See section 15. Crushing chamber alternatives for
quantities.
4 1 442.8791-01 Inner head nut
5 1 442.8800-00 Head nut assembly See section 3c. Head nut with burning ring.
6 1 BG00325390 Main shaft sleeve
7 1 BG00511165 Main shaft cover
8 6 841.0658-00 Screw MF6S 10.9 FZB M20x40
9 1 442.8802-01 Dust seal ring
10 1 442.8801-01 Retaining ring
11 1 442.8804-01 Retainer
12 1 442.8805-01 Scraper
13 1 840.0071-00 Screw M6S M16x65 8.8 ZP
14 11 840.0069-00 Screw M6S M16x55 8.8 ZP
15 12 847.0016-00 Washer BRB 17x30 ZP
16 1 853.0119-00 Pin CP 25x60 m6
17 1 855.0026-00 Retaining ring SgA 100
18 1 899.0504-00 Eye bolt VRS-F-M48 swivel
19 1 BG01616809 Transportation rack, main shaft
20 12 840.0067-00 Screw M6S M16x45 8.8 ZP
21 4 885.0249-00 Sign, Centre of gravity

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 49

SPC Sandvik CH660:06 442.8800

3c. Head nut with burning ring

Pos. No. Qty. Part No. Description Remarks

1 1 442.8800-00 Head nut with burning ring
2 1 452.0269-001 Burning ring
3 2 842.0227-00 Screw SK6SS M12x20

50 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 452.4219

3d. Mantle alternatives

Pos. No. Qty. Part No. Description Remarks

442.8819-01 Mantle A M1
442.8819-02 Mantle A M2
442.8819-03 Mantle A M7
442.8819-05 Mantle A M9
442.8820-01 Mantle B M1
442.8820-02 Mantle B M2
442.8820-03 Mantle B M7
442.8820-05 Mantle B M9
442.8821-01 Mantle D M1
442.8821-02 Mantle D M2
442.8821-03 Mantle D M7
442.8821-05 Mantle D M9
1 1
452.0820-001 Mantle EF M1
452.0820-002 Mantle EF M2
452.0820-003 Mantle EF M7
452.0820-005 Mantle EF M9
442.9760-01 Mantle HC M1
442.9760-02 Mantle HC M2
442.9760-03 Mantle HC M7
442.9760-05 Mantle HC M9
452.6027-001 Mantle FlexiFeed B M1
452.6027-002 Mantle FlexiFeed B M2
452.6027-003 Mantle FlexiFeed B M7
452.6027-005 Mantle FlexiFeed B M9

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 51

SPC Sandvik CH660:06

This page is intentionally left blank

52 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06

4. Dust collar

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 53

SPC Sandvik CH660:06 452.4129

4a. Dust collar

14 3 12

8 9 10 11
5

4 4 7 13

Pos. No. Qty. Part No. Description Remarks

452.4129-901 Dust collar kit Consists of:
1 1 452.4151-001 Dust collar
2 4 840.0634-00 Screw M6S 16x25 8.8 ISO 4017
3 1 442.8744-01 Ring
4 1 853.0464-00 Pin CP m6 12×30 SMS 2374
5 16 840.1281-00 Screw M6S 16×80 8.8
6 16 847.0016-00 Washer BRB 17×30 HB200 ISO 7089
7 1 442.8762-01 Locating bar
8 1 442.8809-01 Shim t=0.1
9 1 442.8809-02 Shim t=0.5
10 1 442.8809-03 Shim t=0.7
11 1 442.8809-04 Shim t=1.0
12 3 841.0019-00 Screw MC6S 10×40 12.9
13 1 442.8808-01 Gasket
14 1 442.8747-01 Seal ring, inner
Service/Repair kit
1 452.5799-901 Locating bar kit See section 4b. Locating bar kit

54 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 452.5799

4b. Locating bar kit

Pos. No. Qty. Part No. Description Remarks
1 452.5799-901 Locating bar kit Consists of:
1 442.8762-01 Locating bar
1 442.8809-01 Shim t=0.1
1 442.8809-02 Shim t=0.5
1 442.8809-03 Shim t=0.7
1 442.8809-04 Shim t=1.0
3 841.0019-00 Screw MC6S 10×40 12.9

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 55

SPC Sandvik CH660:06

This page is intentionally left blank

56 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06

5. Eccentric

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 57

SPC Sandvik CH660:06 BG01541821

5a. Eccentric AM assembly, throw 18-20-24-28

6 5
4
8 10

9 3

11

A-A (1:6)

12

A A

(Continued)

58 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 BG01541821

(Continued)
Pos. No. Qty. Part No. Description Remarks
BG01541821 Eccentric AM assembly, throw 18-20-24-28 Consists of:
1 1 442.8733-01 Eccentric
2 1 442.8824-01 Eccentric bushing, throw 18+20+24+28 See section 5d. Eccentric bushing.
3 1 442.8729-01 Hub
4 1 442.8743-00 Ring
5 8 840.0066-00 Screw M6S M16×40 8.8 FZB ISO4017
6 8 847.0016-00 Washer BRB 17×30 HB200 ISO 7089
7 1 442.9610-01 Key R 28×16×320
8 7 841.0028-00 Screw MC6S 12×100 12.9
9 9 841.0025-00 Screw MC6S 16×50 12.9
10 16 847.0180-00 Washer DIN 137 B 13×24
11 1 442.8723-00 Gear and pinion set See section 5e. Gear and pinion set.
12 1 442.8807-01 Key T50×28×75

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 59

SPC Sandvik CH660:06 BG01541816

5b. Eccentric AM assembly, throw 28-32-36-40

6 5
4
8 10

9 3

11

A-A (1:6)

12

A A

(Continued)

60 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 BG01541816

(Continued)
Pos. No. Qty. Part No. Description Remarks
BG01541816 Eccentric AM assembly, throw 28-32-36-40 Consists of:
1 1 442.8733-01 Eccentric
2 1 442.8825-01 Eccentric bushing, throw 28-32-36-40 See section 5d. Eccentric bushing.
3 1 442.8729-01 Hub
4 1 442.8743-00 Ring
5 8 840.0066-00 Screw M6S M16×40 8.8 FZB ISO4017
6 8 847.0016-00 Washer BRB 17×30 HB200 ISO 7089
7 1 442.9610-01 Key R 28×16×320
8 7 841.0028-00 Screw MC6S 12×100 12.9
9 9 841.0025-00 Screw MC6S 16×50 12.9
10 16 847.0180-00 Washer DIN 137 B 13×24
11 1 442.8723-00 Gear and pinion set See section 5e. Gear and pinion set.
12 1 442.8807-01 Key T50×28×75

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 61

SPC Sandvik CH660:06 BG01541793

5c. Eccentric AM assembly, throw 40-44-48-50

6 5
4
8 10

9 3

11

A-A (1:6)

12

A A

(Continued)

62 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 BG01541793

(Continued)
Pos. No. Qty. Part No. Description Remarks
BG01541793 Eccentric AM assembly, throw 40-44-48-50 Consists of:
1 1 442.8733-01 Eccentric
2 1 442.8826-01 Eccentric bushing, throw 40-44-48-50 See section 5d. Eccentric bushing.
3 1 442.8729-01 Hub
4 1 442.8743-00 Ring
5 8 840.0066-00 Screw M6S M16×40 8.8 FZB ISO4017
6 8 847.0016-00 Washer BRB 17×30 HB200 ISO 7089
7 1 442.9610-01 Key R 28×16×320
8 7 841.0028-00 Screw MC6S 12×100 12.9
9 9 841.0025-00 Screw MC6S 16×50 12.9
10 16 847.0180-00 Washer DIN 137 B 13×24
11 1 442.8723-00 Gear and pinion set See section 5e. Gear and pinion set.
12 1 442.8807-01 Key T50×28×75

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 63

SPC Sandvik CH660:06 452.4160

5d. Eccentric bushing

Pos. No. Qty. Part No. Description Remarks

Eccentric bushing alternatives Consists of:
1 442.8826-01 Eccentric bushing, throw 40+44+48+50
1 1 442.8825-01 Eccentric bushing, throw 28+32+36+40
1 442.8824-01 Eccentric bushing, throw 18+20+24+28

64 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 448.8723

5e. Gear and pinion set

Pos. No. Qty. Part No. Description Remarks

1 442.8723-00 Gear and pinion set As. Consists of:
1 1 Pinion
Cannot be orderered separately
2 1 Gear

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 65

SPC Sandvik CH660:06

This page is intentionally left blank

66 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06

6. Bottom shell

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 67

SPC Sandvik CH660:06 BG00565178

6a. Bottom shell with rubber liners (standard)

G
1 10 24 21 5 10 11
G
22, 23 G-G (1:10)

F
6 A-A 20 19
F

2 3, 4 E

9
E 9
D E-E (1:10)

7 7

A B A
B (1:10)
8
C
14

D 13
15, 16, 17
18

12
(Continued)

68 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 BG00565178

(Continued)
Pos. No. Qty. Part No. Description Remarks
BG00565178 Bottom shell assembly with rubber liners (stan- Consists of:
dard)
1 1 Bottom shell CH660/CS660 Cannot be ordered separately
2 1 BG00575600 Foot assembly CH660/CS660 See section 6c. Foot assembly.
3 16 840.0669-00 Screw M6S M24x70 8.8 ZP
4 16 847.0124-00 Washer BRB 25x45 ZP
5 1 891.1772-901 Rubber lining bottom shell See section 6d. Rubber lining bottom shell.
6 1 853.0464-00 Pin CP 12x30 m6
7 8 853.0646-00 Spiral pin Prym N 16x45
8 2 442.7907-01 Boss
9 4 843.1578-00 Welded screw PD M12x30 4.8Ni+RF12
10 1 452.5470-901 Bottom shell arm liners CH660/CS660 See section 6h. Arm liners.
11 4 843.1650-00 Weld stud PD M12x25, Steel 4.8
12 1 452.4146-001 Transport frame
13 2 442.9923-00 Lifting tool
14 2 452.7588-001 Secure plate
15 8 840.1070-00 Screw M6S M42x200 8.8 ZP
16 8 847.0171-00 Washer BRB 43x80 ZP
17 8 845.0322-00 Nut M6M M42 8 ZP
18 4 885.0261-00 Information sign, Lift here / Secure here

Not included in the major parts assembly:

19 1 Temperature transmitter alternatives CH660/CS660 See section 6i. Temperature transmitter alterna-
tives.
20 1 900.2108-00 Elbow A4 Zn Rp 4
21 1 442.8742-01 Bottom shell bushing CH660/CS660
22 1 900.1412-00 Pipe R 3/4x70
23 2 900.0276-00 Round cap Rp 3/4 Fe
24 1 442.8761-01 Eccentric wearing plate

The bottom shell is not fully compatible with versions earlier than CH660:02, without upgrading the Hydroset
system. Please contact your local Sandvik representative for support.

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 69

SPC Sandvik CH660:06 BG00565215

6b. Bottom shell with steel wear plates liners (option)

G
1 10 24 21 5 10 11
G
22, 23 G-G (1:10)

F
6 A-A 20 19
F

2 3, 4 E

9
E 9
D E-E (1:10)

7 7

A B A
B (1:10)
8
C
14

D 13
15, 16, 17
18

12
(Continued)

70 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 BG00565215

(Continued)
Pos. No. Qty. Part No. Description Remarks
BG00565215 Bottom shell assembly with steel wear plates liner Consists of:
(option)
1 1 Bottom shell CH660/CS660 Cannot be ordered separately
2 1 BG00575600 Foot assembly CH660/CS660 See section 6c. Foot assembly.
3 16 840.0669-00 Screw M6S M24x70 8.8 ZP
4 16 847.0124-00 Washer BRB 25x45 ZP
5 1 452.7282-901 Steel wear plate lining bottom shell See section 6f. Steel wear plate lining bottom shell
6 1 853.0464-00 Pin CP 12x30 m6
7 8 853.0646-00 Spiral pin Prym N 16x45
8 2 442.7907-01 Boss
9 4 843.1578-00 Welded screw PD M12x30 4.8Ni+RF12
10 1 452.5470-901 Bottom shell arm liners CH660/CS660 See section 6h. Arm liners.
11 4 843.1650-00 Weld stud PD M12x25, Steel 4.8
12 1 452.4146-001 Transport frame
13 2 442.9923-00 Lifting tool
14 2 452.7588-001 Secure plate
15 8 840.1070-00 Screw M6S M42x200 8.8 ZP
16 8 847.0171-00 Washer BRB 43x80 ZP
17 8 845.0322-00 Nut M6M M42 8 ZP
18 4 885.0261-00 Information sign, Lift here / Secure here

Not included in the major parts assembly:

19 1 Temperature transmitter alternatives CH660/CS660 See section 6i. Temperature transmitter alterna-
tives.
20 1 900.2108-00 Elbow A4 Zn Rp 4
21 1 442.8742-01 Bottom shell bushing CH660/CS660
22 1 900.1412-00 Pipe R 3/4x70
23 2 900.0276-00 Round cap Rp 3/4 Fe
24 1 442.8761-01 Eccentric wearing plate

The bottom shell is not fully compatible with versions earlier than CH660:02, without upgrading the Hydroset
system. Please contact your local Sandvik representative for support.

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 71

SPC Sandvik CH660:06 BG00575600

6c. Foot assembly

3 1

1
2

Pos. No. Qty. Part No. Description Remarks

BG00575600 Foot assembly kit Consists of:
1 2 442.8756-01 Foot
2 1 BG00573541 Foot
3 1 BG00573452 Foot

72 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 891.1772

6d. Rubber lining bottom shell

A B

8 9
10
11

7
B (1;5)
A (1;5)
7 1
2
2

10

5 5
6
7

Pos. No. Qty. Part No. Description Remarks

1 891.1772-901 Rubber lining bottom shell kit Consists of:
1 1 891.1856-901 Wall protection
2 3 891.1889-901 Wall protection
3 1 891.1891-901 Wall protection
4 1 891.1893-901 Wall protection
5 3 891.1858-901 Wall protection
6 1 891.1860-901 Wall protection
7 2 891.1647-902 Inspection door PU kit
8 4 847.0147-00 Washer, round 13x24 ZP
9 20 891.2035-901 Bolt and plug set
10 4 891.2035-902 Bolt and plug set
11 4 845.0030-00 Lock nut M12 8 ZP

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 73

SPC Sandvik CH660:06 891.2133

6e. Rubber lining kit

3 5

6
5

1
7
2

Rubber lining wall protection kit 891.2133-901

Pos. No. Qty. Part No. Description Remarks
1 891.2133-901 Rubber lining wall protection kit Consists of:
1 1 891.1891-901 Wall protection
2 1 891.1893-901 Wall protection
3 3 891.1858-901 Wall protection
4 1 891.1860-901 Wall protection
5 3 891.1889-901 Wall protection
6 1 891.1856-901 Wall protection
7 20 891.2035-901 Bolt and plug set
8 2 891.2035-902 Bolt and plug set

74 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 891.2133-901

6f. Steel wear plate lining bottom shell

B
A

6
8 9

B (1:5)
7
A (1:5)
5 4

6
1

6
3

2
7

Pos. No. Qty. Part No. Description Remarks

1 452.7282-901 Steel wear plate lining bottom shell Consists of:
1 1 452.7283-001 Wear plate
2 1 452.7285-001 Wear plate
3 1 452.7288-001 Wear plate
4 1 452.7289-001 Wear plate
5 1 452.7291-001 Wear plate
6 24 BG00207523 Bolt set See section 6g. Bolt set.
7 2 891.1647-901 Inspection door PU kit
8 4 847.0147-00 Washer, round 13x24 ZP
9 4 845.0030-00 Lock nut M12 8 ZP

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 75

SPC Sandvik CH660:06 BG00207523

6g. Bolt set

3
1

Pos. No. Qty. Cat. No. Part No. Description Remarks

1 BG00207523 Bolt set Consists of:
1 1 BG00205920 Bolt
2 1 891.1739-901 Soft washer
3 1 845.0030-00 Lock nut

76 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 452.5470-901

6h. Arm liners

Bottom shell arm liner kit 452.5470-901

Pos. No. Qty. Part No. Description Remarks
1 452.5470-901 Bottom shell arm liner kit Consists of:
1 4 BG01421403 Narrow arm liner
2 1 BG01421592 Pinion shaft arm liner

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 77

SPC Sandvik CH660:06 BG00498892

6i. Temperature transmitter alternatives

1 2
With ACS With ASRi or without control system
(temperature transmitter) (no temperature transmitter)

Pos. No. Qty. Part No. Description Remarks

Temperature transmitter alternative
1 1 Temperature transmitter assembly Refer to the ACS Spare Parts Catalog.
2 1 900.0901-00 Plug R 4 T8 FZV

78 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06

7. Hydroset cylinder

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 79

SPC Sandvik CH660:06 BG00382125

7a. Hydroset cylinder

21
22 19

23
6, 5 C-C
B-B (1:10)
E-E

20
E
15

2, 3

8
E
7
1
10
C
11
C
12

4
17
16 13 14 18, 3
B B

(Continued)

80 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 BG00382125

(Continued)
Pos. No. Qty. Part No. Description Remarks
Hydroset cylinder assembly Consists of:
1 1 442.8722-01 Hydroset cylinder CH660/CS660
4 1 442.8724-01 Cylinder bushing CH660/CS660
5 4 840.0019-00 Screw M6S M8x12 8.8 ZP
6 7 847.0012-00 Washer BRB 8,4x16 ZP
7 1 442.8758-00 Piston assembly CH660/CS660 See section 7b. Piston
8 1 853.0119-00 Pin CP 25x60 m6
10 1 442.8739-00 Piston seal, Chevron packing See section 7d. Chevron packing
11 1 442.8725-01 Clamping plate
12 8 841.0266-00 Screw MC6S M12x25 8.8 ZP
13 1 452.4865-001 Hydroset cylinder cover
14 1 Position transmitter alternatives CH660/CS660 See section 7e. Position transmitter alternatives
15 1 873.1152-00 O-ring 625,0x7 NBR 70
16 1 873.0838-00 O-ring 499,3x5,7 NBR 70
17 1 873.1277-00 O-ring 548x5,7 NBR 70
19 1 900.2302-00 Plug VSTI G 1/2" -ED
20 1 Hydroset protection alternatives CH660/CS660 See section 7h. Hydroset protection alternatives
21 1 873.0390-00 Seal ring, Tredo 30
22 1 900.0659-00 Adapter G 2 BxG 2 B
23 1 900.3279-00 Cap G2-11

Not included in the major parts assembly:

2 21 840.0672-00 Screw M6S 24×100 8.8 ISO 4014
3 39 847.0124-00 Washer BRB 25×45 HB200 SS 3576
9 1 BG00259473 Step bearing set CH660/ CS660 See section 7c. Step bearing set
18 18 840.0674-00 Screw M6S M24x120 8.8 ZP

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 81

SPC Sandvik CH660:06 BG00382125

(Continued)

20

14
With ACS or ASRi With protection

20

14
Without ACS or ASRi Without protection

Pos. No. Qty. Part No. Description Remarks

14 1 Position transmitter alternatives See section 7e. Position transmitter alternatives
CH660/ CS660
20 1 Hydroset protection alternatives See section 7h. Hydroset protection alternatives
CH660/CS660

82 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 442.8758

7b. Piston

1
2

Pos. No. Qty. Part No. Description Remarks

1 1 442.8738-00 Piston
2 1 442.7559-05 Measuring tube

7c. Step bearing set BG00259473

1
2
3

Pos. No. Qty. Part No. Description Remarks

1 BG00259473 Step bearing set CH660/CS660 Includes the following
1 1 Main shaft step
2 1 Step washer Sold as a set.
3 1 Piston wearing plate

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 83

SPC Sandvik CH660:06 442.8739

7d. Chevron packing

6 1

5 4 2 3

Pos. No. Qty. Part No. Description Remarks

1 1 442.8739-00 Chevron packing
2 1 840.0019-00 Screw MC6S 8×12 8.8
3 1 847.0012-00 Washer BRB 8.4×16 HB200 ISO 7089
4 1 873.1277-00 Seal, O-ring 548.0×5.7 SMS 1586
5 1 873.0838-00 Seal, O-ring 499.3×5.7 SMS 1586
6 8 841.0266-00 Screw MC6S 12×25 8.8

84 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 BG00497035

7e. Position transmitter alternatives

Pos. No. Qty. Part No. Description Remarks

Position transmitter alternatives
1 1 BG00496918 Position transmitter plug See section 7f. Position transmitter plug
2 1 442.8790-00 Position transmitter assembly See section 7g. Position transmitter assembly
ASRi CH660/ CS660 B1N ASRi
3 1 Position transmitter assembly Refer to the ACS Spare Parts Catalog.
ACS CH660/ CS660 K1-GT1

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 85

SPC Sandvik CH660:06 BG00496918

7f. Position transmitter plug

2
4, 3

Pos. No. Qty. Part No. Description Remarks

BG00496918 Position transmitter plug Consists of:
1 1 442.8783-01 Plug
2 1 873.0111-00 O-ring 44,2x3,0 NBR 70
3 6 847.0012-00 Washer BRB 8,4x16 ZP
4 6 840.0023-00 Screw M6S M8x25 8.8 ZP
5 4 840.0019-00 Screw M6S M8x12 8.8 ZP

86 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 442.8790

7g. Position transmitter assembly ASRi

1
3 7 4

6, 5

Pos. No. Qty. Part No. Description Remarks

1 442.8790-00 Position transmitter assembly ASRi kit Consists of:
1 1 984.0623-00 Position sensor 300 mm, 5-pin
2 1 873.0111-00 O-ring 44,2x3,0 NBR 70
3 6 841.0239-00 Screw MC6S M8x40 8.8 zincpl
4 1 442.8785-00 Guard
5 3 847.0012-00 Washer BRB 8,4x16 ZP
6 3 840.0021-00 Screw M6S M8x20 8.8 ZP
7 1 194.0565-003 Prewired cable, Plug Canon M12 Male 5P 3m

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 87

SPC Sandvik CH660:06 BG00523132

7h. Hydroset protection alternatives

2
1

Pos. No. Qty. Part No. Description Remarks

Hydroset protection alternatives
1 1 BG00491449 Hydroset protection CH660 See section 7i. Hydroset protection
2 1 Hydroset protection, screws CH660/CS660 See section 7j. Hydroset protection screws

88 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 BG00491449

7i. Hydroset protection

7 7 9 2 1
8
5
6
10
1 3

Pos. No. Qty. Part No. Description Remarks

BG00491449 Hydroset protection kit Consists of:
1 2 BG00437388 Bracket
2 1 BG00438540 Bracket
3 1 BG00437993 Skirt
4 1 BG00520816 Skirt
5 1 BG00521348 Skirt
6 10 840.0045-00 Screw M6S M12x30 8.8 ZP
7 23 847.0147-00 Washer 13x24 ZP
8 13 840.0047-00 Screw M6S M12x40 8.8 ZP
9 13 845.0030-00 Lock nut M12 8 ZP
10 13 847.0118-00 Washer S4B 13,5x40

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 89

SPC Sandvik CH660:06 BG00528949

7j. Hydroset protection screws

Pos. No. Qty. Part No. Description Remarks

Hydroset protection screws kit Consists of:
1 12 840.0045-00 Screw M6S M12x30 8.8 ZP
2 12 847.0147-00 Washer 13x24 ZP

90 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06

8. Hydroset system

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 91

SPC Sandvik CH660:06 BG00347975

8a. Hydroset system

With ASRi With ACS

3 3 1

20
B-B
15

A (1:5) A (1:5)
5

6
4

7
9
8
10
B
A
B 16, 17 2

19 11, 12, 13, 14

18

21

(Continued)

92 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 BG00347975

(Continued)

Pos.No. Qty. Part No. Description Remarks

Hydroset system CH660 Consists of:
1 2 BG00368225 Check valve See section 8b. Check valve.
2 2 BG00464502 Cover CH660/CS660 See section 8c. Cover.
3 1 Pressure transmitter alternatives See section 8d. Pressure transmitter alternatives.
4 2 452.4862-001 Support accumulator
5 1 Accumulator alternatives CH660 See section 8e. Accumulator alternative.
6 2 452.0441-001 Clamp
7 4 847.0059-00 Washer TBRSB 13,5x36 ZP
8 4 840.0048-00 Screw M6S M12x45 8.8 ZP
9 4 847.0132-00 Washer, round 21x36 ZP
10 4 840.0650-00 Screw M6S M20x65 8.8 ZP
11 1 873.0385-00 Seal ring, Tredo 20 3/4
12 1 900.0655-00 Adapter G 3/4 BxG 3/4 B
13 1 900.0964-00 Adapter G 3/4 BxG 3/4 Swivel
14 1 900.0276-00 Round cap Rp 3/4 Fe
15 4 840.0076-00 Screw M6S M20x40 8.8 ZP
16 4 873.0390-00 Seal ring, Tredo 30
17 2 900.0659-00 Adapter G 2 BxG 2 B
18 2 452.5968-001 Hydraulic Hose 2" EN 857-2SC
19 2 900.2265-00 Plug VSTI G 3/4'' -ED
20 1 900.2279-00 Plug VSTI G 1/4" -ED
21 2 819.0061-00 Cable protection L=1,6

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 93

SPC Sandvik CH660:06 BG00368225

8b. Check valve

9 8

7
4
6
5

2 1

A-A

A A

Pos. No. Qty. Part No. Description Remarks

1 BG00368225 Check valve Consists of:
1 1 BG00368222 Connection
2 1 442.6407-01 Seat
3 1 442.6403-01 Valve
4 1 127.0004-30 Spring
5 1 442.6406-01 Valve body
6 2 873.0130-00 O-ring 114,3x5,7
7 1 442.6405-01 Valve guide
8 1 442.6402-01 Flange
6 840.0532-00 Screw M6S M20x110 8.8 ZP

94 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 BG00464502

8c. Cover

6
2 7 3
4
1 5
7

Pos. No. Qty. Part No. Description Remarks

BG00464502 Cover Consists of:
1 1 BG00353817 Bracket
2 1 BG00525698 Bracket
3 4 BG00353824 Clamping bar
4 2 BG00353819 Rubber protection
5 8 841.0432-00 Screw MF6S M10x25 8.8
6 4 840.0045-00 Screw M6S M12x30 8.8 ZP
7 4 847.0147-00 Washer 13x24 ZP

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 95

SPC Sandvik CH660:06 BG00492217

8d. Pressure transmitter alternatives

With ACS

2
With ASRi
or
without control system

Pos. No. Qty. Part No. Description Remarks

Pressure transmitter alternatives Consists of:
1 1 900.2279-00 Plug VSTI G 1/4" -ED
2 1 Pressure transmitter assembly Refer to the ACS Spare Parts Catalog.

96 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 919.0243

8e. Accumulator alternative

1
2

Pos. No. Qty. Part No. Description Remarks

1 2 919.0243-00 Accumulator complete 20 l Uncharged 0.2 MPa
2 919.0205-00 Bladder Spare part included in accumulator
2 1 919.0125-00 Gas charging unit

The accumulator is delivered uncharged. Use the gas charging unit to charge.
Charging pressure:
• 4.2 MPa without ASR / with ASR Plus
• 6.0 MPa with ASRi or ACS

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 97

SPC Sandvik CH660:06

This page is intentionally left blank

98 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06

9. Pinion shaft housing

assembly

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 99

SPC Sandvik CH660:06 BG01352427

9a. Pinion shaft housing aftermarket assembly

6 9 2 1 3 14, 13

23 17 12 24 16

C
B

5 22 20 21 19, 27
A-A 5
4
4
28
C 28
B

27 18 A
15
25 8, 7
26

10, 11
A

(Continued)

100 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 BG01352427

(Continued)
Pos. No. Qty. Part No. Description Remarks
BG01352427 Pinion shaft housing assembly Consists of:
1 1 442.8764-01 Pinion shaft housing
2 1 868.0799-00 Bearing 22224 E
3 1 868.0806-00 Bearing 452324 M2/W502
4 2 BG01177609 Spacer
5 2 873.0128-00 O-ring 109,1x5,7 NBR 70
6 1 BG01179326 Bearing cover, inner
7 6 840.0035-00 Screw M6S 10X25 8.8
8 6 847.0144-00 Washer BRB 10,5x22 HB200
9 1 442.8775-01 Gasket
10 6 840.0067-00 Screw M6S M16x45 8.8 ZP
11 6 847.0016-00 Washer BRB 17x30 ZP
12 1 BG01165780 Bearing cover
13 1 442.8774-01 Gasket
14 1 442.8774-02 Gasket
15 1 853.0590-00 Spiral pin Prym N 8x28
16 1 BG01530491 Pinion shaft
17 1 857.0350-00 Key TK 25x14x95
18 1 900.0022-00 Elbow A4 Zn DN20 zinced
19 1 900.2026-00 Magnetic plug 0606-12
20 1 BG01177702 Oil level plug
21 2 873.0108-00 O-ring 34,2x3,0 NBR 70
22 1 442.7578-01 Pipe
23 1 855.0132-00 Retaining ring SgA 110
24 1 857.0336-00 Key TK 28x16x110
25 1 900.0655-00 Adapter G 3/4 BxG 3/4 B
26 1 900.3180-00 Cap G3/4
27 2 873.0385-00 Seal ring, Tredo 20 3/4
28 4 873.1710-00 Oil seal ring 150x180x12 Viton
29 1 BG00392209 Corrlam Alu-VpCI 300 x 400 mm
30 1 S_233.1915-xx Modification Guide

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 101

SPC Sandvik CH660:06 BG01352427

9b. Fasteners and gaskets for pinion shaft housing

5, 4, 3 1, 2

Pos. No. Qty. Part No. Description Remarks

Fasteners and gaskets for pinion shaft housing Consists of:
1 8 840.0072-00 Screw M6S 16x70 8.8
2 8 847.0060-00 Washer TBRSB 17x42
3 1 442.8803-01 Gasket T=0.5
4 1 442.8803-02 Gasket T=0.8
5 1 442.8803-03 Gasket T=1.5
6 2 840.1063-00 Screw M6S M16x120H 8.8 ZP
7 2 845.0009-00 Nut M6M M16 8 ZP

102 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 BG01362209

9c. Pinion shaft housing repair kit

Pos. No. Qty. Part No. Description Remarks
BG01362209 Pinion shaft housing repair kit Consists of:
1 1 873.0385-00 Tredo NR.20 3/4"
2 2 873.0108-00 O-ring 34,2x3 SMS 1586
3 1 868.0799-00 Bearing
4 1 868.0806-00 Bearing
5 2 873.0128-00 O-ring 109,1x5,7 SMS 1586
6 2 BG01177609 Spacer
7 4 873.1710-00 Oil seal ring
8 1 442.8803-01 Gasket
9 1 442.8803-02 Gasket
10 1 442.8803-03 Gasket
11 1 442.8774-01 Gasket
12 1 442.8774-02 Gasket
13 1 442.8775-01 Gasket

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 103

SPC Sandvik CH660:06

This page is intentionally left blank

104 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06

10. Hoses

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 105

SPC Sandvik CH660:06 BG00491525

10a. Hoses assembly

1 L
5
2 M

3 N

4 Q

Pos. No. Cat. No. Qty. Part No. Description Remarks

Hoses assembly CH660/CS660 Consists of:
1 1 BG00501792 Return oil hose 4" See section 10b. Hose.
2 1 650.0093-32 Hydraulic hose
3 1 BG00496465 Hydraulic hose 3/4"
4 1 650.0089-28 Hose SAE 100R1AT R3/4"x2000
5 1 Adapter alternatives CH660/CS660 See section 10c. Adapter
kit alternative.

* For information about how to connect the hoses, see the installation drawing.

10b. Hose BG00501792

3 1 2

Pos. No. Qty. Part No. Description Remarks

1 BG00501792 Return Oil Hose 4" Consists of:
1 4 900.2090-00 Hose clip SC d 113-121
2 1 650.0326-25 Hose 4"x2500
3 1 442.2549-01 Connection

106 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 BG00505402

10c. Adapter kit alternative

1 BSP
L

2 JIC
L

Pos. No. Qty. Part No. Description Remarks

Adapter kit alternative Consists of:
1 1 BG00505401 Adapter kit BSP CH660/CS660 See section 10d. Adapter kit BSP.
2 1 BG00505400 Adapter kit JIC CH660/CS660 See section 10e. Adapter kit JIC.

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 107

SPC Sandvik CH660:06 BG00505401

10d. Adapter kit BSP

Crusher hoses Tank

L

Cooler Cooler
1 outlet inlet
M

N 2 4 5 5 4 2 6

3 3 7
Q

3 3 7

Pos. No. Qty. Part No. Description Remarks

1 BG00505401 Adapter kit BSP Consists of:
1 1 442.2549-01 Connection
2 2 900.0659-00 Adapter G 2 BxG 2 B
3 4 900.0655-00 Adapter G 3/4 BxG 3/4 B
4 2 900.2161-00 Adapter G 2 BxG 1 1/2 B
5 2 873.0388-00 Seal ring, Tredo 28
6 1 873.0390-00 Seal ring, Tredo 30
7 2 873.0385-00 Seal ring, Tredo 20 3/4

108 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 BG00505400

10e. Adapter kit JIC

Crusher hoses Tank

L

Cooler Cooler
1 outlet inlet 2
M

3 4 5 5 4 3 6
N

7 7 8
Q

7 7 8

Pos. No. Qty. Part No. Description Remarks

1 BG00505400 Adapter kit JIC Consists of:
1 1 442.9830-01 Coupling, Hose 4"
2 1 442.9831-01 Adapter R4xNPT4
3 2 900.2321-00 Adapter JIC 2 1/2x"G 2" B
4 2 900.2429-00 Adapter JIC 2 1/2"xG 1 1/2" B
5 2 873.0388-00 Seal ring, Tredo 28
6 1 873.0390-00 Seal ring, Tredo 30
7 4 900.2316-00 Adapter JIC 1 1/16xG3/4 B
8 2 873.0385-00 Seal ring, Tredo 20 3/4

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 109

SPC Sandvik CH660:06

This page is intentionally left blank

110 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06

11. Dust seal air pressure unit

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 111

SPC Sandvik CH660:06 BG01335728

11a. Dust seal air pressure assembly

1 2 A-A

A
A

Pos. No. Qty. Part No. Description Remarks

Dust seal air pressure unit
1 1 Dust seal air pressure unit See section 11b. Dust seal air pressure unit.
2 1 Dust seal air pressure connection See section 11e. Dust seal air pressure connec-
tion.

112 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 BG01047665

11b. Dust seal air pressure unit

4
1

Pos. No. Qty. Part No. Description Remarks

Dust seal air pressure unit Consists of:
1 Dust seal air pressure fan SV 130/2 See section 11c. Dust seal air pressure fan.
2 819.0345-00 Hose w. steel spiral
3 900.2283-00 Clip, Hose 45-50mm
4 452.8006-901 Filter FK 1500 Assembly

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 113

SPC Sandvik CH660:06 BG01036041

11c. Dust seal air pressure fan

5 4 3 2 1

Pos. No. Qty. Part No. Description Remarks

Dust seal air pressure fan Consists of:
1 1 906.0667-00 Dust seal air pressure fan SV 130/2
2 1 126.0917-001 Sign L3-M1
3 4 840.0021-00 Screw M6S M8x20 8.8 ZP
4 1 900.0155-00 Bushing N4 Zn DN40/25 zinced
5 1 900.1427-00 Hose coupling R1 1/2
972.2035-00 Motor W22 71-B5T-0,75 2 230V/400V50, 460V60
972.1925-00 Motor W22 71-B5T-0,75 2 575V60
6 1 972.2036-00 Motor W22 71-B5T-0,75 2 690V50
972.1924-00 Motor W22 71-B5T-0,75 2 380V60
972.1923-00 Motor W22 71-B5T-0,75 2 525V50

Dust seal air pressure fan with motor assemblies

BG01036041-01 Dust seal air pressure fan 130/2
230V50
BG01036041-02 Dust seal air pressure fan 130/2
400V50/460V60
BG01036041-03 Dust seal air pressure fan 130/2
525V50
BG01036041-04 Dust seal air pressure fan 130/2
1
690V50
BG01036041-05 Dust seal air pressure fan 130/2
380V60
BG01036041-06 Dust seal air pressure fan 130/2
525V50
BG01036041-07 Dust seal air pressure fan 130/2 Without motor
without motor

114 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 452.8006

11d. Filter

Pos. No. Qty. Part No. Alternative Description Remarks

452.8006-901 Filter assembly Consists of:
1 1 452.7581-001 Adapter
2 1 912.0373-00 Air filter FK1500 complete
1 912.0374-00 Filter spare part
3 1 126.0843-001 Sign FU5

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 115

SPC Sandvik CH660:06 BG01335708

11e. Dust seal air pressure connection

44 22 1 11 12

13
13

A 77
6 5 8 1 3

A (1:2) 8 10 8 9

Pos. No. Qty. Part No. Description Remarks

BG01335708 Dust seal air pressure connection Consists of:
1 2 900.1425-00 Hose coupling R 1" d=25
2 1 819.0344-00 Hose 1" PVC w. steel spiral L = 15 m
3 2 900.1358-00 Hose clip D 32
4 4 900.1140-00 Clip RSGU D32 1.32/15
5 1 900.0648-00 Adapter G 1 BxG 3/4 B
6 2 873.0386-00 Seal ring, Tredo 23
7 1 902.1190-00 Flow valve M/840 G 3/4"
8 3 873.0385-00 Seal ring, Tredo20 3/4
9 1 900.1158-00 Reducing socket Rp 1x3/4
10 1 900.0655-00 Adapter G 3/4 BxG 3/4 B
11 1 900.0042-00 T-pipe 1 B1
12 1 900.0212-00 Plug R 1 T8 FZV
13 1 900.0145-00 Bushing N4 Zn DN25/20 zinced

116 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06

12. Drive

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 117

SPC Sandvik CH660:06 BG01434282

12a. V-belt drive

K A 15 28, 29

24, 25 J 27

K-K
28, 26
2 1 6, 4, 5 3 10
K A 25, 28
B H 32, 31
20, 22 16, 17
F
21
23, 30 19, 18 D
E-E E E
8 7 11, 13
A-A

14,12 C

L
7

(Continued)

118 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 BG01434282

(Continued)
Pos. No. Qty. Part No. Description Remarks
CH660 V-belt drive
1 BG01475045 Sub frame Assembly See section 12b. Sub frame assembly
2 2 452.4582-901 Vibration damper, large See section 12k. Vibration damper, large
3 4 452.8325-901 Vibration damper, small See section 12l. Vibration damper, SAW 200 A
4 8 847.0122-00 Washer TBRB 40x68 ZP
5 4 840.0714-00 Screw M6S M36x140 8.8
6 4 845.0273-00 Lock nut, low M36 8 ZP
7 8 649.0168-01 Supporting cleat
8 4 873.0718-00 Strip 2254 50x30 L=2,0 m
9 1 Belt drive alternatives See section 12e. Drive alternatives
10 1 BG01437294 Motor bracket assembly See section 12c. Motor bracket assembly
11 8 847.0132-00 Washer, round 21x36 ZP
12 8 847.0197-00 Washer TBRSB 21x52x8
13 8 840.0652-00 Screw M6S M20x90 8.8 ZP
14 8 845.0203-00 Lock nut, high M20 8 ZP
15 1 Motor alternatives See section 12d. Motor alternatives
16 4 840.0675-00 Screw M6S M24x140 8.8 ZP
17 4 847.0124-00 Washer BRB 25x45 ZP
18 4 847.0063-00 Washer TBRSB 26x65 1370
19 4 845.0216-00 Lock nut, low M24 8 ZP
20 2 847.0012-00 Washer BRB 8,4x16 ZP ISO
21 1 BG00616109 Potential equalization bar 6 electrical connections
22 2 840.0026-00 Screw M6S M8x40 8.8 ZP
23 2 845.0205-00 Nut, Lock high M8 8 ZP
24 2 847.0144-00 Washer BRB 10,5x22x2 ZP
25 4 845.0213-00 Lock nut, high M10 8 ZP
26 2 840.0038-00 Screw M6S M10x40 8.8 ZP
27 1 BG01499250 V-belt cover assembly See section 12j. V-belt cover
28 6 847.0058-00 Washer TBRSB 10x28 ZP
29 2 840.0040-00 Screw M6S M10x50 8.8 ZP
30 2 964.3255-00 Washer Contact M8
31 1 847.0059-00 Washer TBRSB 13,5x36 ZP
32 1 840.0048-00 Screw M6S M12x45 8.8 ZP

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 119

SPC Sandvik CH660:06 BG01475045

12b. Sub frame assembly

18, 11 12, 11 12, 11

B C D

8, 7 10, 9
B C D

A-A
6 1 F 3

11, 16
A 11, 17
19
H
A
4 H

5
G
15
11, 17
F-F 16, 11
13, 14 2 G
F
E

(Continued)

120 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 BG01475045

(Continued)

Pos. No. Qty. Part No. Description Remarks

BG01475045 Sub frame assembly, belt drive
1 1 BG01460589 Sub frame, belt drive
2 1 BG01475044-01 Floor Plate, Right
3 1 BG01475044-02 Floor Plate, Left
4 1 BG01475189 Beam UPE 220
5 1 BG01475210 Floor Plate
6 2 BG01527482 Cover
7 4 840.0068-00 Screw M6S M16x50 8.8 ZP
8 4 847.0060-00 Washer TBRSB 17x42
9 4 847.0016-00 Washer BRB 17x30 ZP
10 4 845.0215-00 Lock Nut M16 8 ZP
11 24 847.0147-00 Washer BRB 13x24 ZP
12 6 840.0046-00 Screw M6S M12x35 8.8 ZP
13 4 847.0012-00 Washer BRB 8,4x16 ZP
14 4 840.0020-00 Screw M6S M8x16 8.8 ZP I
15 1 BG01530015 Toe Plate
16 4 840.0048-00 Screw M6S M12x45 8.8 ZP
17 4 845.0030-00 Nut, Lock M12 8 ZP
18 10 840.0045-00 Screw M6S M12x30 8.8 ZP
19 1 BG01543685 Toe Plate

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 121

SPC Sandvik CH660:06 BG01437294

12c. Motor bracket assembly

4 5 5 3
A
2

1 6

A 8, 7

A-A

Pos. No. Qty. Part No. Description Remarks

BG01437294 Motor bracket assembly
1 1 BG01436201-01 Motor bracket, right
2 1 BG01436201-02 Motor bracket, left
3 2 840.1035-00 Screw M6S M24x260 8.8 ZP
4 2 840.1104-00 Screw M6S M24x220 8.8 ZP
5 4 845.0012-00 Nut M6M M24 8 ZP
6 1 BG01577861 Belt cover support
7 2 847.0144-00 Washer BRB 10,5x22x2 ZP
8 2 840.0035-00 Screw M6S M10x25 8.8 ZP

122 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 BG00990330

12d. Motor alternatives

Pos. No. Qty. Part No. Description Remarks

Electric motor alternatives
1 1 972.1420-00 Electric motor 315 kW
W22-355-315-4-B3T
380-400-415 V 50 Hz
660-690 V 50 Hz
460 V 60 Hz
2 1 972.1440-00 Electric motor 315 kW
W22-355-315-4-B3T
575 V 60 Hz
3 1 972.1899-00 Electric motor 315 kW
W22-355-315-4-B3T
380 V 60 Hz
4 1 972.1888-00 Electric motor 315 kW
W22-355-315-4-B3T
525 V 50 Hz
5 1 972.2310-00 Electric motor 315 kW
W21-355-220-4-B3T
380-400-415 V 50 Hz
660-690 V 50 Hz
460 V 60 Hz
6 1 972.2311-00 Electric motor 315 kW
W21-355-220-4-B3T
575V 60Hz
7 1 972.2312-00 Electric motor 315 kW
W21-355-220-4-B3T
525V 50Hz
8 1 972.2031-00 Electric motor 315 kW
W22-355-315-4-B3T
6000V 50Hz
9 1 972.2033-00 Electric motor 315 kW
W22-355-315-4-B3T
4160V 60Hz
10 1 972.2414-00 Electric motor 315 kW
W51 315 kW 4-Pole B3R(E)
6000V 50Hz
11 1 972.2415-00 Electric motor 315 kW
W51 315 kW 4-Pole B3R(E)
4160V 60Hz

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 123

SPC Sandvik CH660:06 452.4443

12e. Drive alternatives

1
A 4

A
A-A

Pos. No. Qty. Part No. Description Remarks

Drive alternatives
1 1 V-belt drive SPC 50 Hz See section 12f. V-belt drive SPC 50 Hz 4-pole
2 1 V-belt drive SPC 60 Hz See section 12g. V-belt drive SPC 60 Hz 4-pole
3 1 V-belt drive 8V 60Hz See section 12h. V-belt drive 8V 60 Hz 4-pole
4 1 442.9969-00 Spacer See section 12i. Spacer

124 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 452.4749

12f. V-belt drive SPC 50 Hz 4-pole

B 11
9
5
2
11
A 7
4
8 3
B
10 6

B-B (1:5)
10 A-A (1:5)
A

Motor

Crusher

Pos. No. Qty. Part No. Alternative Description Remarks

V-belt drive SPC 50 Hz 4-pole
1 1 452.7737-901 V-belt pulley 500 MTG125 12×SPC
2 1 869.0286-00 Bushing MGT No. 125, Di 110
869.0261-00 Di 80
869.0278-00 Di 85
869.0295-00 Di 90
869.0283-00 Di 95
869.0235-00 Di 100
3 1 Bushing MGT No. 125
869.0286-00 Di 110
869.0314-00 Di 3 7/8
869.0410-00 Di 3 5/8
869.0411-00 Di 3 3/8
869.0418-00 Di 4 3/8
4 1 857.0336-00 Key T 28×16×110 SMS 2307
5 1 442.8788-01 Spacer
6 1 442.8787-01 Washer
7 1 847.0016-00 Washer BRB 17×30 ISO 7089
8 1 840.0066-00 Screw M6S M16×40 8.8 FZB ISO4017
9 1 879.0499-00 V-belt pulley 400 MGT 125 12×SPC
10 12 875.0246-00 V-belt SPC 3150
11 4 Screw MC6S M20x70 12.9 Included in bushing, pos 2.

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 125

SPC Sandvik CH660:06 452.4750

12g. V-belt drive SPC 60 Hz 4-pole

B
11
9
5
2
A
11
7
B
4 3
8
10
6
A B-B (1:5)
10
A-A (1:5)

Motor

Crusher

Pos. No. Qty. Part No. Alternative Description Remarks

1 V-belt drive SPC 60 Hz 4-pole
1 1 452.7741-901 V-belt pulley 560 MTG125 12×SPC
2 1 869.0286-00 Bushing MGT No. 125, Di 110
869.0261-00 Di 80
869.0278-00 Di 85
869.0295-00 Di 90
869.0283-00 Di 95
869.0235-00 Di 100
3 1 Bushing MGT No. 125
869.0286-00 Di 110
869.0314-00 Di 3 7/8
869.0410-00 Di 3 5/8
869.0411-00 Di 3 3/8
869.0418-00 Di 4 3/8
4 1 857.0336-00 Key T 28×16×110 SMS 2307
5 1 442.8788-01 Spacer
6 1 442.8787-01 Washer
7 1 847.0016-00 Washer BRB 17×30 HB200 ISO 7089
8 1 840.0066-00 Screw M6S M16×40 8.8 FZB ISO4017
9 1 879.0509-00 V-belt pulley 375 MGT125 12×SPC
10 12 875.0246-00 V-belt SPC 3150
11 4 Screw MC6S M20x70 12.9 Included in bushing, pos 2

126 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 452.4751

12h. V-belt drive 8V 60 Hz 4-pole

B
11
9
1 6
A
8
4
B 2
5
10 11
3
B-B (1:5)
A
10
A-A (1:5)

Motor

Crusher

Pos. No. Qty. Part No. Alternative Description Remarks

1 V-belt drive 8V 60Hz 4-pole
1 1 869.0286-00 Bushing MGT125 Di 110
2 1 857.0336-00 Key T 28×16×110
3 1 442.8787-01 Washer
4 1 847.0016-00 Washer BRB 17×30 HB200 ISO 7089
5 1 840.0066-00 Screw M6S M16×40 8.8 FZB ISO4017
6 1 442.8788-01 Spacer
7 1 452.7743-901 V-belt pulley 560 MGT125 12x8V
869.0261-00 Di 80
869.0278-00 Di 85
869.0295-00 Di 90
869.0283-00 Di 95
869.0235-00 Di 100
3 1 Bushing MGT No. 125
869.0286-00 Di 110
869.0314-00 Di 3 7/8
869.0410-00 Di 3 5/8
869.0411-00 Di 3 3/8
869.0418-00 Di 4 3/8
9 1 879.0820-00 V-Belt Pulley 375 MGT125 12x8V
10 12 875.0331-00 V-belt 8V 1250 Standard C-C 856
11 4 Screw MC6S M20x70 12.9 Included in bushing, pos 1

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 127

SPC Sandvik CH660:06 442.9969

12i. Spacer

2 1

5 4

Pos. No. Qty. Part No. Description Remarks

1 442.9969-00 Spacer Consists of:
1 1 857.0336-00 Key T 28x16x110
2 1 442.8832-03 Spacer
3 1 442.8787-02 Washer 2142-50, D134/18x15
4 1 847.0016-00 Washer BRB 17x30 HB200
5 1 840.0066-00 Screw M6S M16x40 8.8 FZB

128 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 BG01499250

12j. V-belt cover

A 10, 9, 11 8, 5

14
A D
13 12
D C
C

B 3

B 2
1

4, 6, 7
15

Pos. No. Qty. Part No. Description Remarks

BG01499250 V-belt cover Consists of:
1 1 BG01577099 V-Belt Cover
2 1 BG01577804 Bracket
3 1 BG00301483 Bracket
4 4 847.0144-00 Washer BRB 10,5x22x2 ZP
5 2 847.0058-00 Washer TBRSB 10x28 ZP
6 2 840.0037-00 Screw M6S M10x35 8.8 ZP
7 2 845.0213-00 Nut, Lock M10 8 ZP
8 2 840.0035-00 Screw M6S M10x25 8.8 ZP
9 26 847.0012-00 Washer BRB 8,4x16 ZP
10 13 840.0021-00 Screw M6S M8x20 8.8 ZP
11 13 845.0205-00 Nut, Lock high M8 8 ZP
12 1 BG00298127 Lid
13 4 BG00300483 Screw modified Ø2,5 hole
14 4 853.0231-00 Pin, split SP 2,5x20 SMS 66
15 2 840.1010-00 Screw M6S M12x16 8.8 ZP

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 129

SPC Sandvik CH660:06 452.4582

12k. Vibration damper, large

Pos. No. Qty. Part No. Description Remarks

1 452.4582-901 Vibration damper, large, kit Consists of:
1 1 442.5904-01 Plate
2 1 864.0066-00 Vibration damper SAW 300 A
3 4 840.1135-00 Screw M6S 20×35 8.8 ZP
4 12 847.0132-00 Washer, round 21×36 ZP
5 4 840.0078-00 Screw M6S 20×60 8.8 ZP
6 4 845.0203-00 Lock nut, high M20 8 ZB

130 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 452.8325

12l. Vibration damper, SAW 200 A

3 4
6
5
1
2

Pos. No. Qty. Part No. Description Remarks

452.8325-901 Vibration damper SAW 200 A Consists of:
1 1 864.0124-00 Vibration damper SAW 200 A
2 1 452.8324-001 Mounting plate
3 12 847.0016-00 Washer BRB 17x30 ZP
4 4 845.0215-00 Nut, Lock high M16 8 ZP
5 4 840.0066-00 Screw M6S M16x40 8.8 fzb
6 4 840.0069-00 Screw M6S M16x55 8.8 ZP

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 131

SPC Sandvik CH660:06

This page is intentionally left blank

132 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06

13. Sign board

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 133

SPC Sandvik CH660:06 452.4548

13a. Sign board

2 4
2
4 5 5

6 6
2
2

9
1 2

B
3 10
1
8
7
3
C
C
8

(Continued)

134 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 452.4548

(Continued)
Pos. No. Qty. Part No. Alternative Description Remarks
1 452.4548-901 Sign board Consists of:
1 1 126.0383-001 Warning sign - Risk of crushing
2 4 126.0384-001 Warning sign - Flying fragments
3 1 126.0385-001 Warning sign - Read manual
4 2 126.0445-001 SANDVIK logotype silver 140×385
5 2 126.0416-001 Sign - Product name
6 4 885.0249-00 Sign - Center of gravity
7 1 126.5007-01 Identification plate
8 1 Yes Warning sign alternatives See section 13b. Warning sign alterna-
tives.
9 4 885.0262-00 Sign - Lifting plate chain
10 1 126.0785-001 Sign - Earth connection

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 135

SPC Sandvik CH660:06 BG01109918

13b. Warning sign alternatives

. .

Pos. No. Qty. Part No. Language Description Remarks

Warning sign - Danger alternatives
885.0267-00 English
885.0273-00 Romanian
885.0267-01 Bulgarian
885.0267-02 Czech
885.0267-03 Danish
885.0267-04 German
885.0267-05 Greek
885.0267-06 Spanish
885.0267-07 Finnish
885.0267-08 French
885.0267-09 Hungarian Language according to customer require-
1 1 Warning sign - Danger
885.0267-10 Italian ments

885.0267-11 Lithuanian
885.0267-12 Dutch
885.0267-13 Norwegian
885.0267-14 Polish
885.0267-15 Brazilian
885.0267-16 Portuguese
885.0267-17 Russian
885.0267-18 Swedish
885.0267-19 Turkish
885.0267-20 Chinese

136 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06

14. Tool kit

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 137

SPC Sandvik CH660:06 BG00373424

14a. Tool box

1 17 7 16 10 11 12 13 14 15

6
8

9 4 18
3
5
2

Pos. No. Qty. Part No. Description Remarks

1 BG00373424 Tool kit Consists of:
1 1 442.9476-00 Tool box 866x366x361
2 1 904.0585-00 Air bleeder hose L= 500 mm630 Bar Air bleeding of hydraulic system
3 1 923.0422-00 Feeler gauge 0.05-1 mm, L=300
4 1 BG00227693 Lifting tool CH660/CS660 Eccentric bushing
5 1 BG00227701 Lifting tool CH660/CS660 Bottom shell bushing
6 1 BG00227711 Lifting tool, Step bearing Step bearing components
7 5 442.0800-90 Lead cylinder D30 Check of close side setting
8 1 920.0110-00 Tool, slugging wrench NV 65 Screw & nut M24
9 1 920.0151-00 Tool, slugging wrench NV36 Screw & nut M42
10 1 899.0504-00 Eye bolt VRS-F-M48 Swivel
11 3 899.0510-00 Eye bolt VRS-F-M20 Swivel
12 4 899.0509-00 Eye bolt VRS-F-M16 Swivel
13 4 899.0508-00 Eye bolt VRS-F-M12 Swivel
14 2 899.0507-00 Eye bolt VRS-F-M10 Swivel
15 2 899.0512-00 Eye bolt VRS-F-M8 Swivel
16 1 BG00362732 Hydraulic pump, Main shaft, with mounting See section 14c. Hydraulic pump unit and quick cou-
oil pling
17 1 BG00363970 Cover kit CH/S660 See section 14b. Cover kit
18 BG00875591 Grease gauge

138 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 BG00363970

14b. Cover kit

Pos. No. Qty. Part No. Description Remarks

1 BG00363970 Cover kit Consists of:
1 1 BG00214772 Cover CH660/CS660
2 12 847.0359-00 Washer BRB 21x37 HB200
3 4 847.0147-00 Washer, round 13x24 ZP
4 12 841.0041-00 Screw MC6S M20x90 12,9
5 4 841.0027-00 Screw MC6S M12x70 12.9

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 139

SPC Sandvik CH660:06 BG00362732

14c. Hydraulic pump unit and quick coupling

Pos. No. Qty. Part No. Description Remarks

1 1 BG00362732 Hydraulic pump unit Quick coupling and oil included
2 1 BG00600996 Quick coupling Spare part
3 1 914.0240-00 Hydraulic oil, 1 liter (0.26 US gallons) Spare part

140 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 141

SPC Sandvik CH660:06

This page is intentionally left blank

142 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 Crushing Chamber Alternatives

15. Crushing chamber

alternatives

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 143

SPC Sandvik CH660:06 Crushing Chamber Alternatives

15a. Crushing chamber alternatives

(Continued)

144 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 Crushing Chamber Alternatives

(Continued)
Pos. No. Qty. Part No. Description Remarks
452.4211-901 Cone EC Rubber
1 1 452.4212-901 Cone C Rubber Feed hopper
452.4213-901 Cone MC Rubber
442.8823-01 Filler ring MC (M)
1
442.8863-01 Filler ring MF (F)
2 6 840.1074-00 Screw M6S M30x280 8.8 ZP
6 442.8881-01 Washer Fasteners for filler ring
6 442.8908-01 Hose 31.5-0.6
BG00420395-01 Concave ring EC M1
BG00420395-02 Concave ring EC M2
BG00420395-03 Concave ring EC M7
BG00420395-05 Concave ring EC M9
BG00420433-01 Concave ring CX M1
BG00420433-02 Concave ring CX M2
BG00420433-03 Concave ring CX M7
BG00420433-05 Concave ring CX M9
442.8814-01 Concave ring C M1
442.8814-02 Concave ring C M2
442.8814-03 Concave ring C M7
442.8814-05 Concave ring C M9
442.8815-01 Concave ring MC M1
442.8815-02 Concave ring MC M2
442.8815-03 Concave ring MC M7
442.8815-05 Concave ring MC M9
3 1
442.8816-01 Concave ring M M1
442.8816-02 Concave ring M M2
442.8816-03 Concave ring M M7
442.8816-05 Concave ring M M9
442.8817-01 Concave ring MF M1
442.8817-02 Concave ring MF M2
442.8817-03 Concave ring MF M7
442.8817-05 Concave ring MF M9
442.8818-01 Concave ring F M1
442.8818-02 Concave ring F M2
442.8818-03 Concave ring F M7
442.8818-05 Concave ring F M9
452.0832-001 Concave ring EF M1
452.0832-002 Concave ring EF M2
452.0832-003 Concave ring EF M7
452.0832-005 Concave ring EF M9

(Continued)

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 145

SPC Sandvik CH660:06 Crushing Chamber Alternatives

(Continued)
Pos. No. Qty. Part No. Description Remarks
442.8819-01 Mantle A M1
442.8819-02 Mantle A M2
442.8819-03 Mantle A M7
442.8819-05 Mantle A M9
442.8820-01 Mantle B M1
442.8820-02 Mantle B M2
442.8820-03 Mantle B M7
442.8820-05 Mantle B M9
442.8821-01 Mantle D M1
442.8821-02 Mantle D M2
442.8821-03 Mantle D M7
442.8821-05 Mantle D M9
1 1
452.0820-001 Mantle EF M1
452.0820-002 Mantle EF M2
452.0820-003 Mantle EF M7
452.0820-005 Mantle EF M9
442.9760-01 Mantle HC M1
442.9760-02 Mantle HC M2
442.9760-03 Mantle HC M7
442.9760-05 Mantle HC M9
452.6027-001 Mantle FlexiFeed B M1
452.6027-002 Mantle FlexiFeed B M2
452.6027-003 Mantle FlexiFeed B M7
452.6027-005 Mantle FlexiFeed B M9

(Continued)

146 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 Crushing Chamber Alternatives

(Continued)
The table below illustrates the different crushing chamber alternatives
Example of the type number shown on the crusher’s identification plate:

CH660:0X-M/B/MC-36/40/44/32
Combination Concave (6005-0) Mantle (4175-0) Filler ring (6006-0) Feed hopper cone (7100-0)

EC/A EC Extra Coarse A EC Extra Coarse

442.8813-01 (M1) 442.8819-01 (M1)
442.8813-02 (M2) 442.8819-02 (M2)
452.4211-901 (Rubber)
442.8813-03 (M7) 442.8819-03 (M7)
442.8813-05 (M9) 442.8819-05 (M9)
Casting comp. 5×10 kg Casting comp. 9×10 kg

EC/B EC Extra Coarse B EC Extra Coarse

442.8813-01 (M1) 442.8820-01 (M1)
442.8813-02 (M2) 442.8820-02 (M1)
452.4211-901 (Rubber)
442.8813-03 (M7) 442.8820-03 (M7)
442.8813-05 (M9) 442.8820-05 (M9)
Casting comp. 5×10 kg Casting comp. 5×10 kg

EC/D EC Extra Coarse D EC Extra Coarse

442.8813-01 (M1) 442.8821-01 (M1)
442.8813-02 (M2) 442.8821-02 (M2)
452.4211-901 (Rubber)
442.8813-03 (M7) 442.8821-03 (M7)
442.8813-05 (M9) 442.8821-05 (M9)
Casting comp. 5×10 kg Casting comp. 9×10 kg

EC/ EC Extra Coarse Flexifeed B EC Extra Coarse

Flexifeed B 442.8813-01 (M1) 452.6027-001 (M1)
442.8813-02 (M2) 452.6027-002 (M2)
452.4211-901 (Rubber)
442.8813-03 (M7) 452.6027-003 (M7)
442.8813-05 (M9) 452.6027-005 (M9)
Casting comp. 5×10 kg Casting comp. 7×10 kg

CX/A CX A CX
442.9230-01 (M1) 442.8819-01 (M1)
442.9230-02 (M2) 442.8819-02 (M2)
BG00975710 (Rubber)
442.9230-03 (M7) 442.8819-03 (M7)
442.9230-05 (M9) 442.8819-05 (M9)
Casting comp. 13×10 kg Casting comp. 9×10 kg

CX/D CX D CX
442.9230-01 (M1) 442.8821-01 (M1)
442.9230-02 (M2) 442.8821-02 (M2)
BG00975710 (Rubber)
442.9230-03 (M7) 442.8821-03 (M7)
442.9230-05 (M9) 442.8821-05 (M9)
Casting comp. 13×10 kg Casting comp. 9×10 kg

(Continued)

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 147

SPC Sandvik CH660:06 Crushing Chamber Alternatives

(Continued)
The table below illustrates the different crushing chamber alternatives
Example of the type number shown on the crusher’s identification plate:

CH660:0X-M/B/MC-36/40/44/32
Combination Concave (6005-0) Mantle (4175-0) Filler ring (6006-0) Feed hopper cone (7100-0)

CX/Flexifeed CX Flexifeed B CX
B 442.9230-01 (M1) 452.6027-001 (M1)
442.9230-02 (M2) 452.6027-002 (M2)
BG00975710 (Rubber)
442.9230-03 (M7) 452.6027-003 (M7)
442.9230-05 (M9) 452.6027-005 (M9)
Casting comp. 13×10 kg Casting comp. 7×10 kg

C/A C Coarse A C Coarse

442.8814-01 (M1) 442.8819-01 (M1)
442.8814-02 (M2) 442.8819-02 (M2)
452.4212-901 (Rubber)
442.8814-03 (M7) 442.8819-03 (M7)
442.8814-05 (M9) 442.8819-05 (M9)
Casting comp. 21×10 kg Casting comp. 9×10 kg

C/B C Coarse B C Coarse

442.8814-01 (M1) 442.8820-01 (M1)
442.8814-02 (M2) 442.8820-02 (M2)
452.4212-901 (Rubber)
442.8814-03 (M7) 442.8820-03 (M7)
442.8814-05 (M9) 442.8820-05 (M9)
Casting comp. 21×10 kg Casting comp. 5×10 kg

C/D C Coarse D C Coarse

442.8814-01 (M1) 442.8821-01 (M1)
442.8814-02 (M2) 442.8821-02 (M2)
452.4212-901 (Rubber)
442.8814-03 (M7) 442.8821-03 (M7)
442.8814-05 (M9) 442.8821-05 (M9)
Casting comp. 21×10 kg Casting comp. 9×10 kg

C/Flexifeed B C Coarse Flexifeed B C Coarse

442.8814-01 (M1) 452.6027-001 (M1)
442.8814-02 (M2) 452.6027-002 (M2)
452.4212-901 (Rubber)
442.8814-03 (M7) 452.6027-003 (M7)
442.8814-05 (M9) 452.6027-005 (M9)
Casting comp. 21×10 kg Casting comp. 7×10 kg

MC/A/MC MC Medium A MC Medium MC Medium Coarse

442.8815-01 (M1) 442.8819-01 (M1)
442.8815-02 (M2) 442.8819-02 (M2)
442.8823-01 452.4213-901 (Rubber)
442.8815-03 (M7) 442.8819-03 (M7)
442.8815-05 (M9) 442.8819-05 (M9)
Casting comp. 14×10 kg Casting comp. 9×10 kg Casting comp. 13×10 kg

(Continued)

148 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 Crushing Chamber Alternatives

(Continued)
The table below illustrates the different crushing chamber alternatives
Example of the type number shown on the crusher’s identification plate:

CH660:0X-M/B/MC-36/40/44/32
Combination Concave (6005-0) Mantle (4175-0) Filler ring (6006-0) Feed hopper cone (7100-0)

MC/B/MC MC Medium B MC Medium MC Medium Coarse

442.8815-01 (M1) 442.8820-01 (M1)
442.8815-02 (M2) 442.8820-02 (M2)
442.8823-01 452.4213-901 (Rubber)
442.8815-03 (M7) 442.8820-03 (M7)
442.8815-05 (M9) 442.8820-05 (M9)
Casting comp. 14×10 kg Casting comp. 5×10 kg Casting comp. 13×10 kg

MC/D/MC MC Medium D MC Medium MC Medium Coarse

442.8815-01 (M1) 442.8821-01 (M1)
442.8815-02 (M2) 442.8821-02 (M2)
442.8823-01 452.4213-901 (Rubber)
442.8815-03 (M7) 442.8821-03 (M7)
442.8815-05 (M9) 442.8821-05 (M9)
Casting comp. 14×10 kg Casting comp. 9×10 kg Casting comp. 13×10 kg

MC/Flexifeed MC Medium Flexifeed B MC Medium Coarse MC Medium Coarse

B/MC 442.8815-01 (M1) 452.6027-001 (M1)
442.8815-02 (M2) 452.6027-002 (M2)
442.8823-01 452.4213-901 (Rubber)
442.8815-03 (M7) 452.6027-003 (M7)
442.8815-05 (M9) 452.6027-005 (M9)
Casting comp. 14×10 kg Casting comp. 7×10 kg Casting comp. 13×10 kg

MC/HC/MC MC Medium HC MC/ Medium Coarse MC Medium Coarse

442.8815-01 (M1) 442.9760-01 (M1)
442.8815-02 (M2) 442.9760-02 (M2)
442.8823-01 452.4213-901 (Rubber)
442.8815-03 (M7) 442.9760-03 (M7)
442.8815-05 (M9) 442.9760-05 (M9)
Casting comp. 14×10 kg Casting comp. 7×10 kg Casting comp. 13×10 kg

M/A/MC M Medium A MC/ Medium Coarse MC Medium Coarse

442.8816-01 (M1) 442.8819-01 (M1)
442.8816-02 (M2) 442.8819-02 (M2)
442.8823-01
442.8816-03 (M7) 442.8819-03 (M7)
442.8816-05 (M9) 442.8819-05 (M9)
Casting comp. 14×10 kg Casting comp. 9×10 kg Casting comp. 13×10 kg

M/B/MC M Medium B MC/ Medium Coarse MC Medium Coarse

442.8816-01 (M1) 442.8820-01 (M1)
442.8816-02 (M2) 442.8820-02 (M2)
442.8823-01
442.8816-03 (M7) 442.8820-03 (M7)
442.8816-05 (M9) 442.8820-05 (M9)
Casting comp. 14×10 kg Casting comp. 5×10 kg Casting comp. 13×10 kg

(Continued)

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 149

SPC Sandvik CH660:06 Crushing Chamber Alternatives

(Continued)
The table below illustrates the different crushing chamber alternatives
Example of the type number shown on the crusher’s identification plate:

CH660:0X-M/B/MC-36/40/44/32
Combination Concave (6005-0) Mantle (4175-0) Filler ring (6006-0) Feed hopper cone (7100-0)

M/D/MC M Medium D MC/ Medium Coarse MC Medium Coarse

442.8816-01 (M1) 442.8821-01 (M1)
442.8816-02 (M2) 442.8821-02 (M2)
442.8823-01
442.8816-03 (M7) 442.8821-03 (M7)
442.8816-05 (M9) 442.8821-05 (M9)
Casting comp. 14×10 kg Casting comp. 9×10 kg Casting comp. 13×10 kg

M/HC/MC M Medium HC MC/ Medium Coarse MC Medium Coarse

442.8816-01 (M1) 442.9760-01 (M1)
442.8816-02 (M2) 442.9760-02 (M2)
442.8823-01 452.4213-901 (Rubber)
442.8816-03 (M7) 442.9760-03 (M7)
442.8816-05 (M9) 442.9760-05 (M9)
Casting comp. 14×10 kg Casting comp. 7×10 kg Casting comp. 13×10 kg

MF/A/MF MF/ Medium Fine A MF/ Medium Fine

442.8817-01 (M1) 442.8819-01 (M1)
442.8817-02 (M2) 442.8819-02 (M2)
442.8863-01
442.8817-03 (M7) 442.8819-03 (M7)
442.8817-05 (M9) 442.8819-05 (M9)
Casting comp. 9×10 kg Casting comp. 9×10 kg Casting comp. 13×10 kg

MF/B/MF MF/ Medium Fine B MF Medium Fine

442.8817-01 (M1) 442.8820-01 (M1)
442.8817-02 (M2) 442.8820-02 (M2)
442.8863-01
442.8817-03 (M7) 442.8820-03 (M7)
442.8817-05 (M9) 442.8820-05 (M9)
Casting comp. 9×10 kg Casting comp. 5×10 kg Casting comp. 13×10 kg

MF/D/MF MF/ Medium Fine D MF Medium Fine

442.8817-01 (M1) 442.8821-01 (M1)
442.8817-02 (M2) 442.8821-02 (M2)
442.8863-01
442.8817-03 (M7) 442.8821-03 (M7)
442.8817-05 (M9) 442.8821-05 (M9)
Casting comp. 9×10 kg Casting comp. 9×10 kg Casting comp. 13×10 kg

MF/HC/MF MF/ Medium Fine HC MF Medium Fine

442.8817-01 (M1) 442.9760-01 (M1)
442.8817-02 (M2) 442.9760-02 (M2)
442.8863-01
442.8817-03 (M7) 442.9760-03 (M7)
442.8817-05 (M9) 442.9760-05 (M9)
Casting comp. 9×10 kg Casting comp. 7×10 kg Casting comp. 13×10 kg

(Continued)

150 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06 Crushing Chamber Alternatives

(Continued)
The table below illustrates the different crushing chamber alternatives
Example of the type number shown on the crusher’s identification plate:

CH660:0X-M/B/MC-36/40/44/32
Combination Concave (6005-0) Mantle (4175-0) Filler ring (6006-0) Feed hopper cone (7100-0)

F/A/MF F Fine A MF Medium Fine

442.8818-01 (M1) 442.8819-01 (M1)
442.8818-02 (M2) 442.8819-02 (M2)
442.8863-01
442.8818-03 (M7) 442.8819-03 (M7)
442.8818-05 (M9) 442.8819-05 (M9)
Casting comp. 13×10 kg Casting comp. 9×10 kg Casting comp. 13×10 kg

F/B/MF F Fine B MF Medium Fine

442.8818-01 (M1) 442.8820-01 (M1)
442.8818-02 (M2) 442.8820-02 (M2)
442.8863-01
442.8818-03 (M7) 442.8820-03 (M7)
442.8818-05 (M9) 442.8820-05 (M9)
Casting comp. 13×10 kg Casting comp. 5×10 kg Casting comp. 13×10 kg

F/D/MF F Fine D MF Medium Fine

442.8818-01 (M1) 442.8821-01 (M1)
442.8818-02 (M2) 442.8821-02 (M2)
442.8863-01
442.8818-03 (M7) 442.8821-03 (M7)
442.8818-05 (M9) 442.8821-05 (M9)
Casting comp. 13×10 kg Casting comp. 9×10 kg Casting comp. 13×10 kg

F/HC/MF F Fine HC MF Medium Fine

442.8818-01 (M1) 442.9760-01 (M1)
442.8818-02 (M2) 442.9760-02 (M2)
442.8863-01
442.8818-03 (M7) 442.9760-03 (M7)
442.8818-05 (M9) 442.9760-05 (M9)
Casting comp. 13×10 kg Casting comp. 7×10 kg Casting comp. 13×10 kg

EF/EF EF Extra Fine EF Extra Fine

452.0832-001 (M1) 452.0820-001 (M1)
452.0832-002 (M2) 452.0820-002 (M2) Wear plate (4 pieces)
452.0832-003 (M7) 452.0820-003 (M7) 442.9415-00

452.0832-005 (M9) 452.0820-005 (M9)

Casting comp. 15×10 kg Casting comp. 7×10 kg

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 151

SPC Sandvik CH660:06 Crushing Chamber Alternatives

This page is intentionally left blank

152 Doc. no. R 223.1526 Ver. 05 © 2021 Sandvik SRP AB

SPC Sandvik CH660:06

16. Recommended spare parts

© 2021 Sandvik SRP AB Doc. no. R 223.1526 Ver. 05 153

RECOMMENDED SPARES

SANDVIK CH660:06

Qty
Qty. installed in Weight Qty per Qty per Qty per Qty per
Cat. No. Part Number Description Casting
each crusher kgs/each 2000hrs 4000hrs 6000hrs 8000hrs
Compund
891.1772-901 Bottom rubber liner wall protection kit 1 102,0 1 1 2 2
452.5470-901 Bottom shell arm liner manganese kit 1 455,0 1 1 2 2
* 891.1897-901 Rubber liners for cone EC kit 1 1 1 2 2
* 891.1902-901 Rubber liners for cone C kit 1 1 1 2 2
* 891.1908-901 Rubber liners for cone MC kit 1 1 1 2 2
5150-0 442.8812-00 Arm shield 2 70,0 1 1 2 2
*4175-9 831.0016-00 Casting compound See Column F 10,0
*4175-0 442.8819-01 Mantle A 1 1167,0 9** As req. As req. As req. As req.
*4175-0 442.8820-01 Mantle B 1 1132,0 5** As req. As req. As req. As req.
*4175-0 452.0820-001 Mantle EF 1 1215,0 7** As req. As req. As req. As req.
*4175-0 442.9760-01 Mantle HC 1 1215,0 7** As req. As req. As req. As req.
*4175-0 442.8821-01 Mantle D 1 1177,0 9** As req. As req. As req. As req.
*4175-0 452.6027-001 Mantle Flexifeed B 1 1191,0 6** As req. As req. As req. As req.
*6005-0 452.0832-001 Concave ring EF 1 1235,0 13** As req. As req. As req. As req.
*6005-0 442.8815-01 Concave ring MC 1 1295,0 13** As req. As req. As req. As req.
*6005-0 442.8814-01 Concave ring C 1 1220,0 20** As req. As req. As req. As req.
*6005-0 442.8818-01 Concave ring F 1 1128,0 13** As req. As req. As req. As req.
*6005-0 442.8817-01 Concave ring MF 1 1180,0 9** As req. As req. As req. As req.
*6005-0 442.8816-01 Concave ring M 1 1218,0 14** As req. As req. As req. As req.
*6005-0 442.9230-01 Concave ring CX 1 1365,0 12** As req. As req. As req. As req.
*6005-0 442.8813-01 Concave ring EC 1 1295,0 5** As req. As req. As req. As req.
6050 442.8793-01 Support ring 1 180,0 ****** ****** ****** ******
5651-0 873.1401-00 O-ring for spider cap 1 0,01 1** 1** 1** 1**
4205-0 442.8800-00 Head nut / Burning ring 1 83,0 *** *** *** ***
4205-2 452.0269-001 Burning ring 1 4,1 **** **** **** ****
5675-0 442.8754-01 Spider bushing 1 85,0 1 1 2 2
5705-0 442.8755-01 Oil seal ring 1 1,2 1** 1** 1** 1**
825.0182-00 Grease Tribol tin 18,0 kgs. 1 18,0 1/2***** 1/2***** 1/2***** 1/2*****
1430-0 442.8808-01 Gasket 1 0,1 1 1 1 1
BG00259473 Step bearing set 1 125,0 1 1 2 2
4025-0 BG00325390 Mainshaft sleeve 1 85,0 1 1 1 1
4305-0 442.8802-01 Dust seal ring 1 17,0 1 1 1 1
4355-0 442.8804-01 Retainer 1 0,3 1 1 1 1
452.5799-901 Locating bar kit 1 1 1 1
4355-1 442.8805-01 Scraper 1 0,4 1 2 3 4
452.5793-901 Fastener kit concave + support ring 1 2 2 4 4
6105-0 442.8290-01 Dowel pin 4 0,7 4 4 4 4
912.0155-00 Airfilter insert (topshell, breather) 1 0,0 1 2 3 4
912.0374-00 Overpressure filter insert 1 1,3 1 2 3 4

Plus Parts (these parts will normally not be consumed on annual basis)

5650-0 BG01116737 Spider cap 1 340,0

6050-0 442.8793-01 Support ring 1 177,0
1200-0 442.8742-01 Bottom shell bushing 1 173,0
*1810-0 442.8824-01 Eccentric bushing 18+20+24+28 1 260
*1810-0 442.8825-01 Eccentric bushing 28+32+36+40 1 207
*1810-0 442.8826-01 Eccentric bushing 40+44+48+50 1 207
1880-0 442.8761-01 Eccentric wearing plate 1 32,0
2050-0 442.8724-01 Hydroset cylinder bushing 1 82,0
BG01362209 Pinion shaft repair kit 1
3505-0 BG01530491 Pinion shaft 1 101,0
4205-1 442.8791-01 Inner head nut 1 21,0
4350-0 442.8801-01 Dust seal retaining ring 1 93,0
BG01618707 Mainshaft ass.excl. Mantle 1 4800,0
BG00395488 Top Shell ass. Excl. Concave 1 5100,0
BG01352427 Pinionshaft housing ass. Excl.pulley 1 370,0
OPTIONAL Parts for electrical dump valve
902.1189-00 Directional valve 1
984.1678-00 Pressure transmitter 1
902.1201-00 Sealing kit for directional valve 1

Filters, pumps and all tank related parts see Tank recommendation parts.
* Alternative or order connected
** Per manganese change
*** 1 Head nut / Burning ring per every second manganese change
**** 1 Burning ring per manganese change when not changing Head nut. When changing Head nut you get a burning ring together with the Head nut
***** 1/2 Grease Tribol tin 18,0 kgs. per manganese change (7-9 kg)
****** 1 every fourth manganese change