Technical Data Sheet
NATIONAL SPRAY PLASTER MEDIUM
DESCRIPTION TYPICAL PROPERTIES
National Spray Plaster Medium is a ready to use
• Color & Appearance
plaster based on modified acrylic copolymer
binder reinforced with precisely graded inert Color of Dry Film Off White
aggregate fillers. It is designed for interior
applications, as a sprayable plaster. Finish of Dry Film Matt
• Specific Gravity 1.70 ± 0.05
• Volume Solids
USES 60 ± 2 %
(ASTM D 2697)
National Spray Plaster Medium is • Film Thickness
recommended for interior applications over
Wet Film Thickness (WFT) 5 mm/coat
National Spray Plaster Coarse on ceilings. It is
always recommended as an undercoat plaster. Dry Film Thickness (DFT) 3 mm/coat
• Drying Time
Drying Time (Touch Dry) @ 30°C 3 – 4 hours
ADVANTAGES
Drying Time (Dry to Recoat) @
• Excellent workability 30°C
24 hours
• Pre blended, ready to use sprayable plaster
• Excellent adhesion Drying Time (Full Dry) @ 30°C 48 hours
• Low volume shrinkage post drying
2.80 kg/m2/mm
(depends on the
• Theoretical Spreading Rate
substrate and
COMPLIANCE & CERTIFICATIONS application)
National Spray Plaster Medium complies with
local regulatory standards for VOC. The product PACKAGING SIZE
complies with ESMA ECAS Green Label 5 star.
• 25 kg
* Certificates are available upon request.
This data sheet supersedes all previous issued.
ISO 9001, 14001 & 45001
Issued: 0622
CERTIFIED FACTORY
www.nationalpaints.com Page 1 of 2
Technical Data Sheet
SURFACE PREPARATION SAFETY PRECAUTIONS
The surface should be clean, free of oil, grease, • Avoid skin and eye contact by wearing overalls,
loose particles and other contaminants before gloves, goggles, and mask etc.
application of coating. • Skin Contact: Rinse with water. If skin irritation
or rash occurs, seek medical attention
immediately.
APPLICATION METHOD • Eye contact: Rinse cautiously with water for
several minutes. Consult an eye specialist
• Spray Equipment
immediately.
• Putty Knife • Avoid inhalation of vapors and paint mist by
• Scraper wearing suitable mask.
Cleaning solvent: Water • In the event of ingestion seek medical
Dilution: Ready to use attention immediately.
• Painting must be carried out in well-ventilated
area.
RECOMMENDED SYSTEM • Local safety regulations need to be followed.
National Spray Plaster Coarse 1 coat
STORAGE & SHELF LIFE
National Spray Plaster Medium 1 coat
National Spray Plaster Fine 1 coat
• Store the paint in proper storage conditions as
per the local regulations. Keep the paint
OR container in sealed condition under shed, away
Other National Paints recommended system from direct sunlight and extreme temperatures.
• Do not keep paint material near to any ignition
• Apply a required wet film thickness upto 5mm per
sources.
• Do not put back the half or unused material
coat and level the surface evenly.
back in original container, containing the
• If the area requires wet film thickness more than
supplied paint, to avoid contamination.
5 mm, two coats of spray plaster should be
• Handle with care.
applied. In such cases, the first coat should left • Stir well before use.
with a scratched finish for subsequent coats. • Shelf life at 30°C is 18 months in original sealed
• Maintain adequate drying time between 2 coats, container, with proper storage conditions.
normally 24 hours.
• The total dry film thickness of two coats should
however, not exceed 6mm.
• Finish with one or two coats of National Spray
Plaster Fine.
NOTE: We warranty only the quality of our product and this data sheet is based on results obtained from experience and tests. We
reserve the right to change data without prior notice. For safety details kindly refer safety data sheet.
This data sheet supersedes all previous issued.
ISO 9001, 14001 & 45001
Issued: 0622
CERTIFIED FACTORY
www.nationalpaints.com Page 2 of 2
