No. 1.

CWFL-10000/12000/15000
FIBER LASER SPECIAL CHILLER
USER MANUAL
 CWFL-10000/12000/15000 Series

Contents

<1> Cautions ----------------------------------------------------------------------------- 3

<2> Contour and parts introduction --------------------------------------------- 4

<3> Installation ------------------------------------------------------------------------- 5

<4> Unit introduction and parameters adjustment ------------------------- 6

<5> Conductivity meter(optional) ------------------------------------------------ 11

<6> Alarm and communication output ----------------------------------------- 11

<7> MODBUS RS-485 communication function ----------------------------- 12

<8> Simple troubleshooting -------------------------------------------------------- 16

Attachment – Schematic ------------------------------------------------------------- 17

2
 CWFL-10000/12000/15000 Series

Thank you for using the machine from GUANGZHOU TEYU

ELECTROMECHANICAL CO., LTD. Please read the installation instructions
carefully before installing and operating and keep it properly.
This installation instructions is not a quality assurance. GUANGZHOU TEYU
ELECTROMECHANICAL CO., LTD reserves the right to the interpretation of
correction of typographical errors, improper mentioned information and product
improvement. The amended content will be reprinted in installation instructions
without notice in advance.

<1> Cautions
1. Please ensure that the power supply and electrical outlet are in good contact
and the earth wire must be firmly grounded!
The water chiller installation must be done by professional person in order to
avoid machine damage or accidents by misoperation.
2. Please make sure there is stable and normal voltage for the working chiller!
As the refrigeration compressor is more sensitive to the power supply and
voltage, so the operating voltage of our standard product is ±10％ of the rated
voltage. If you do need a wider operating voltage range, customization is
available for us.
3. Unmatched power frequency can cause the chiller damage!
Please choose model of 50Hz or 60Hz according to actual circumstance.
4. To protect the pump, it’s strictly forbidden to run the chiller without water in the
storage water tank!
The new machine is packed after draining whole water in the tank, so please
make sure the tank has water inside before machine starting, otherwise it’s
easily to have the pump damaged. When the water level is below the green
(NORMAL) range of the water level gauge, the cooling capacity of our chiller
will go down slightly. Hence please ensure the water level is within the green
(NORMAL) range. To drain through circulating pump is strictly prohibited!
5. Please be sure that the air inlet and air outlet are in good ventilation!
There must be at least 100cm from obstructions to the air outlet and at least
50cm between obstructions and the lateral air inlet.
6. Please pay attention to the effect of the condensate water!
With greater ambient humidity, when the water temperature is lower than the
ambient temperature, the condensate water will generate on the surface of
water circular pipes and the cooled components. If above circumstance
appears, it is recommended to set a higher water temperature or keep pipes
and cooled parts warm.
7. Please do turn on the chiller first before turn on the laser machine; turn off the
laser machine first before turn off the chiller.
8. This product is an industrial equipment. For professional use only!

3
 CWFL-10000/12000/15000 Series

<2> Contour and parts introduction

TEMPERATURE
CONTROLLER

HIGH TEMP PUMP

LOW TEMP PUMP

CONDUCTIVITY METER
LOW PRESSURE
POWER SWITCH
HIGH PRESSURE
ALARM AND
COMMUNICATION
OUTPUT
POWER

AIR OUTLET

AIR INLET
WATER INLET (H)
WATER OUTLET (H)
WATER INLET (L)
WATER OUTLET (L)

WATER SUPPLY INLET

FILTER
WATER LEVEL GAUGE

WASTE WATER DRAIN

WATER DRAIN OVERFALL GAP

4
 CWFL-10000/12000/15000 Series

<3> Installation
It is very simple to install this industrial cooling machine. The installation for the
first time of the new machine can be carried out by following steps:
1. Open the package to check if the machine is intact and all the necessary
accessories are completed.
2. Ensure water quality.
(1) The applicable circulating water for the chiller includes purified water,distilled
water and high purity water. It is forbidden to use liquid with PH valu ＜6.5 or ＞
7,or containing solid particles and corrosive liquids.Clean the filter and change
out the water on aregular basis (every 3 months is suggested) to ensure the
chiller in good running.
(2) When the chiller is stored with water at room temperature lower than 2℃ ,it is
necessary to add anti-freezer in the chiller water tank. It is recommended to use
antifreeze with a concentration of not more than 30% containing ethylene glycol
or propylene glycol.When weather becomes warmer,fill with purified water or
distilled water and run the chiller for 30 minutes to remove the remaining
anti-freezer.Then get the chiller drained and refill with unused circulating water.
3. According to system conditions, please connect the water inlet and outlet pipe
properly.
4. Plug in power, turn on the power switch. (Do not start up without water in the
water tank!)
(1) The water pump starts working once the power switch is turned on. If “E08”
error code is displayed on the upper window of temperature controller, please
adjust the 3-phase wiring connection order
(2) The first time of operating may cause more bubbles in the pipe leading to a flow
alarming occasionally, but running for a few minutes later, it will go back to
normal.
(3) If the chiller starts for the first time, you must immediately check whether the
water pipe leaks.
(4) Power switched on, if the water temperature is under the set value, it is normal
that fans and other components of the machine do not work. The temperature
controller will automatically control the working conditions of the compressor,
magnetic valve, fans and other parts based on the set controlling parameters.
(5) As it takes a longer time to start over the compressor and other components,
according to different conditions, the time is range from seconds to minutes, so
do not turn on and off frequently..
5. Check the water level in the water tank.
The first starting up of a new chiller will empty the air in the water pipe, causing a
slight water level decline, but in order to keep the water level in the green area, it
is allowed to add adequate water again. Please observe and record the current
water level, and inspect it again after the chiller running for a period of time, if
the water level drops obviously, please re-inspect the water pipeline leakage.
6. Adjust parameters of temperature controller.
CWFL-10000/12000/15000 series use an new intelligent controller. It works in
defaulted constant temperature control mode for the low temperature end with
water temperature set at 25 ℃ which can be adjusted as needed. The high
temperature end works in intelligent control mode and it will self-adjust
controlling parameters according to the ambient temperature changes.
Normally users do not need to adjust the parameters. If it is necessary, please
refer to page 6 , “Unit introduction and parameters adjustment.”
7. With automatic startup function, refrigeration system starts working once the
chiller is electrified. (Indicator light is on).

5
 CWFL-10000/12000/15000 Series

<4> Unit introduction and parameters

adjustment
(1) The unit use wire LCD temperature controller to realize more precise
temperature control and stronger capacity of resisting disturbance. It supports
MODBUS-485 communication with transmission distance up to 1.2km;
(2) It has water line anti-icing function. Under standby condition, it functions
when the room temperature is below 5℃;
(3) It has water tank heating function;
(4) It has water line actual flow monitoring function;
(5) It has actual conductivity monitoring function.

1. Temperature control panel introduction and parameters adjustment

(1) The control panel has LCD screen with 7 system operation buttons which are
Language Switching-button (Lang), UP-button (▲), Down-button (▼), Power-button

Set-button (Set), Quick Set-button (Quick Set) and Quit-button (Quit). Turn off
the chiller by pressing the Power-button for 3 sec while other operations can be
completed by short press.

(2) User parameters quick-adjusting: under normal operation condition, press

Quick Set-button to set the user menu. When it displays the set item, press Quick
Set to enter into parameter adjustment interface. Press ▲ or ▼ to to switch the
parameter items. If the parameters need to be modified, press Quick Set-button to
enter into parameter values and press ▲ or ▼ to adjust it. Save the values and
return to parameter quick setting interface by pressing Quit-button when the
adjustment is completed. If there is no more action within 15 sec, it will
automatically exit modifying status with modified parameters saved.
(3) User menu: under normal operation condition, press Set-button for 5 sec to

6
 CWFL-10000/12000/15000 Series

show user input password interface. Input “168” by pressing ▲ or ▼, then press
Set-button to enter into User menu to set the parameters. If the password is
incorrect, it will quit the setting interface and turn to normal operation interface.
The default password 168 must be kept well. The user menu can not be accessed if
the password is forgotten and no backup password is available.
Under user menu, in parameter items interface, press ▲ or ▼ to switch the
items. If the parameters need to be modified, press Set-button to enter into
parameter values and press ▲ or ▼ to adjust it. Save the values and return to
parameter interface by pressing Set-button and press Quit-button to quit the user
menu. If there is no more action within 15 sec, it will automatically exit modifying
status with modified parameters saved.
(4) Check the history failure records: under normal operation condition, press
Set- button and ▲ for 5 sec to access password input interface. Input password
“123” and confirm by pressing Set-button, it will be in failure view status if the
password is correct, if not, it will quit. When the system is under failure records
viewing, it will show the first failure record and code. Press ▲ or ▼ can look over
the failure records and press Quit-button to quit the failure viewing status.
(5) Restore factory settings: under normal operation condition, press and hold

Set-button and Power-button for 10 sec to have the password input interface
popped up then input password “615” to enter into administrator setting
parameters restoration function, and it will display “RECOVERY SUCCESS” and
turn to operation condition after 2 sec. If the password is incorrect, it will quit the
password input interface and turn to operation condition.
(6) Unit operation condition query: the screen will display the operation
conditions of the compressor, water pump and the indoor exhaust temperature
parameters, etc. by pressing Quick Set-button and ▲ at the same time and release
them. Press ▲ or ▼ for page turning and it will automatically exit after displaying
for 5 sec.
(7) Clock adjustment: under normal operation condition, press Quick
Set-button for 5 sec to access clock adjustment interface with time/year flashing.
Press ▲ or ▼ to adjust year and confirm by pressing Quick Set-button; with time
flashing, press ▲ or ▼ to adjust hour and confirm by pressing Quick Set-button;
with minute flashing, press ▲ or ▼ to adjust minute and save the clock setting by
pressing Quick Set- button.
(8) Language switching: the system default language is Chinese. For switching
to English, press Lang-button and the system will change the Chinese interface to
English interface as default language.
(9) Forced refrigeration: under normal operation condition, press ▲ or ▼ at the
same time for 5 sec to activate forced refrigeration function. Press Power-button
can stop the machine and cancel forced refrigeration function.

7
 CWFL-10000/12000/15000 Series

2. Detailed parameter setting is as below table

Factory Register
Order Code Set item Range Remark illustration
setting address
F10～F9 / Intelligent mode /
1 F1 Set temp. 25 0x0401
-20～40 Constant temp mode
setup menu
2 F2 Temp. difference values -15～5 -2 0x0402
of low temp
3 F3 Cooling hysteresis 0.1～3.0 0.8 0.1 resolution ratio 0x0403
system
0 Constant,
4 F4 Way of control 0～1 0 0x0404
1 Intelligent
F10～F9 / Intelligent mode /
5 F5 Set temp. 30 0x0405
-20～40 Constant temp mode
setup menu
6 F6 Temp. difference values -15～5 -2 of high 0x0406

7 F7 Cooling hysteresis 0.1～3.0 1 0.1 resolution ratio temp 0x0407

system
0 Constant,
8 F8 Way of control 0～1 1 0x0408
1 Intelligent
Constant temp. mode
9 F9 The highest set temp. （F10+1）～40 35 0x0409
invalid
Min. 1, Constant
10 F10 The lowest set temp. 1～（F9-1） 20 0x040a
temp. mode invalid

11 F11 Ultra-high room temp.alarm 40～50 45 0x040b

12 F12 Ultra-high water temp. alarm 1～20 10 0x040c

Common in
13 F13 Ultra-low water temp. alarm 1～60 15 0x040d
high&low
14 F14 Temp. alarm delay 0～30 5 Minute Temp 0x040e

15 F15 Sensor failure alarm delay 0～180 10 Second systems 0x040f

Water flow detection delay

16 F16 0～180 5 Second 0x0410
of machine startup

17 F17 Flow alarm delay 0～180 2 Second 0x0411

18 F18 Heating hysteresis 0～10 0.8 0.1 resolution ratio 0x0412

19 F19 Water pump stop delay 0～180 5 Second 0x0413

20 F20 Startup delay 0～180 30 Second 0x0414

Compressor activate
21 F21 0～180 90 Second 0x0415
protection
Turn on setting of phase Single-phase OFF /
22 F22 On off / 0x0416
sequence protection three-phase ON
Turn on setting of external
23 F23 input function On off off 0x0417
(startup and standby)
NO and NC setting of external NO-normally opened /
24 F24 NO / NC NC 0x0418
input function NC-normally closed

25 F25 External input activation delay 0～180 0 Second 0x0419

8
 CWFL-10000/12000/15000 Series

External input standby

26 F26 0～180 0 Second 0x041a
activation delay
With conductivity ON /
Conductivity alarm activation
27 F27 On off / Without conductivity 0x041b
setting
OFF
Ultra-high conductivity alarm
28 F28 0.5～100 10 μs/cm 0x041c
setting value
Relay NO/NC setting under NO-normally opened
29 F29 NO/NC NC 0x041d
lower limit of conductivity NC-normally closed
Relay output setting under
30 F30 0.5～100 2.5 μs/cm 0x041e
lower limit of conductivity
Ultra-low conductivity alarm
31 F31 0.5～100 2 μs/cm 0x041f
setting value
Self-starting after being
32 F32 On off off 0x044d
electrified
0：lock，
33 F33 Key lock of Chiller On/Off 0-1 1 0x0450
1：unlock

NOTE:
(1) In parameter setting status, the system runs under original parameters;
(2) Under Constant Temperature control mode (“ F4” and “F8” set at 0), water
temperature is controlled by “F1” and “F5”;
(3) Under Intelligent Control mode (“ F4” and “F8” set at 1), water temperature
is self-adjusting according to ambient temperature. The temperature difference
is controlled by “F2” and “F6”.
(4) The low temp section and high temp section of the chiller can be set
different control modes.

3. Failure warning processing mode

When alarm occurs, the failure alarm code will be displayed on the upper right
corner of the LCD screen. In alarming state, the alarm sound could be
suspended by pressing any button, but the alarm display remains until the
alarm condition is eliminated.

9
 CWFL-10000/12000/15000 Series

4. Failure code table

Failure Alarm Elimination
Description Alarm action
code phenomenon method
Automatic clearing
Communication E00 shown with after mainboard
E00 None
failure alarm alarm sound and operation panel
are connected well
The compressor, condenser fans
Low temp. system E01 shown with
E01 and heater of the high/low Automatic clearing
flow alarm alarm sound
temp. system shut down
High temp. system E02 shown with Heater of the high temp. system
E02 Automatic clearing
flow alarm alarm sound shut down
Ultra-high room E03 shown with Each refrigeration part runs under
E03 Automatic clearing
temp.alarm alarm sound usual procedures
Low temp. system The compressor, condenser fans
E04 shown with
E04 ultra-low water temp and heater of the high/low temp. Automatic clearing
alarm sound
alarm system shut down
Low temp. system
E05 shown with Each refrigeration part runs under
E05 ultra-high water temp Automatic clearing
alarm sound usual procedures
alarm
High temp. system
E06 shown with Each refrigeration part runs under
E06 ultra-low water temp Automatic clearing
alarm sound usual procedures
alarm
High temp. system
E07 shown with Heater of the high temp. system
E07 ultra-high water temp Automatic clearing
alarm sound shut down
alarm
The water pump, compressor,
Wrong phase and E08 shown with
E08 condenser fans and heater of the Manual clearing
lacking phase alarm alarm sound
high/low temp. system shut down
The compressor, condenser fans
Compressor overload E09 shown with
E09 and heater of the high/low temp. Manual clearing
alarm alarm sound
system shut down
The water pump, compressor,
Low temp. water E10 shown with
E10 condenser fans and heater of the Manual clearing
pump overload alarm alarm sound
high/low temp. system shut down
High temp. water E11 shown with The water pump and high temp.
E11 Manual clearing
pump overload alarm alarm sound system heater shut down
Refrigeration system E12 shown with The compressor and condenser fans
E12 Manual clearing
high pressure alarm alarm sound shut down
Refrigeration system E13 shown with The compressor and condenser fans
E13 Automatic clearing
low pressure alarm alarm sound shut down
Switched to constant temp. mode
Room temp. sensor E14 shown with
E14 and each refrigeration part runs Automatic clearing
failure alarm alarm sound
under usual procedures
Low temp. system The water pump, compressor,
E15 shown with
E15 water temp. sensor condenser fans and heater of the Automatic clearing
alarm sound
failure alarm high/low temp. system shut down
High temp. system
E16 shown with High temp. system water pump and
E16 water temp. sensor Automatic clearing
alarm sound heater shut down
failure alarm
Ultra-high conductivity E17 shown with Each refrigeration part runs under
E17 Automatic clearing
alarm alarm sound usual procedures
Ultra-low conductivity E18 shown with Each refrigeration part runs under
E18 Automatic clearing
alarm alarm sound usual procedures
The unit runs normally under set
Ultra-low water level E19 shown with values; the water pump, compressor,
E19 Automatic clearing
alarm alarm sound condenser fans and heater of the
high/low temp. system shut down
Exhaust temp. sensor E20 shown with Each refrigeration part runs under
E20 Automatic clearing
failure alarm alarm sound usual procedures
Ultra-high exhaust E21 shown with Each refrigeration part runs under
E21 Automatic clearing
temp. alarm alarm sound usual procedures

10
 CWFL-10000/12000/15000 Series

<5> Conductivity meter（Optional）

(1) This machine is equipped with conductivity meter to monitor deionized water,
detection range from 0.1-20μS.
(2) Alarm signal output for deionized water of over standard conductivity values
(optional).
(3) Alarm indicating for deionized water of over standard conductivity values
(optional).

<6> Alarm and communication output

For ensuring the equipment will not be damaged when abnormal condition occurs
in the chiller, it has alarm protection function.

1. Alarm and MODBUS RS-485 communication output wiring diagram.

2. Working condition table of alarm signal

Built-in buzzer of OUT OUT
Unit condition ILUS
temp. controller H1、H2 H1、H3

Working normally No Sound Disconnection Breakover

E00、E01、E08、E09、
Sounds Breakover Disconnection
E10、E12、E13、E15
E02、E03、E11、E14、E16、
Sounds Disconnection Breakover
E17、E18、E20、E21

E04、E05、E06、E07 Sounds Breakover Disconnection Optional

Activate after output

E19 Sounds Breakover Disconnection
terminal delaying
Note: The flow alarm is connected to the normally open relay and normally closed relay
contacts, requiring operating current less than 3A, working voltage less than 300V.

11
 CWFL-10000/12000/15000 Series

<7> MODBUS RS-485 communication

function
This system adapts salve mode of MODBUS-RTU communication,9600 baud rate,
no parity checking,8 data bit,1 stop bit and support MODBUS-RTU 03 (Read
Holding Registers) and 06 (Read Holding Registers) commands. Communication
formats are as below:

1. Command format 03
Host send command
Function code 1 bytes 0x03

From 0x0400 to 0x044a, From 0x0100 to 0x0108,

Initial address 2 bytes
From 0x0800 to 0x0803

Register number 2 bytes From 1 to 10

Slave response
Function code 1 bytes 0x03

Number of bytes 1 bytes 2*N（ "N" is the number of registers ）

Register value N*2 bytes

Error
Error code 1 bytes 0x83

Exception code 1 bytes 01 or 02 or 03 or 04

For example: if the host’s sending address is 1, requests 108-110 command of

slave read register and send 01 03 00 6B 00 03 XX YY,thereinto,01 as slave address,
03 as function code, 00 6B as initial address, 00 03 as register number and XX YY
as the result of CRC verification.
Slave response: 01 03 06 02 2B 00 00 00 64 XX YY, thereinto, 01 as slave address,
03 as function code, 06 as number of bytes, 02 2B 00 00 00 64 corresponding to the
values in 108-110 of register respectively and XX YY as verification code.
If the slave receives wrong data, return to data 01 83 01 XX YY, thereinto, 01 as
slave address. 83 as error code, 01 as exception code and XX YY as check sum.

2. Command format 06
Host send command
Function code 1 bytes 0x06
Register address 2 bytes From 0x0400 to 0x044a
Register value 2 bytes From 0x000 to 0xffff

12
 CWFL-10000/12000/15000 Series

Slave response
Function code 1 bytes 0x86
Register address 2 bytes From 0x0400 to 0x044a
Register value 2 bytes From 0x000 to 0xffff

Error
Error code 1 bytes 0x86
Exception code 1 bytes 01 or 02 or 03 or 04

For example: if the host’s sending address is 1, requests command of writing data
00 03 to register 2. Host send: 01 06 00 02 00 03 XX YY, thereinto, 01 as slave
address, 06 as function code, 00 02 as register address, 00 03 as written data and XX
YY as verification code.
Slave response: 01 06 00 02 00 03 XX YY, thereinto, 01 as slave address, 06 as
function code, 00 02 as register address, 00 03 as written data and XX YY as CRC
verification code.
If there is data error or communication exception, send 01 86 02 XX YY.

3. Read only parameter（sensor, current）

Read-only

Register Data
Description Range Default Unit Symbol
address resolution
Room temp. sensor
0x0100 -25 ~ 100 ℃ 0.1/bit yes
temperature
Water temp. sensor
0x0101 -25 ~ 100 ℃ 0.1/bit yes
temperature(Low temp)
Water temp. sensor
0x0102 -25 ~ 100 ℃ 0.1/bit yes
temperature(High temp)
Compressor exhaust
0x0103 -25 ~ 140 ℃ 0.1/bit yes
temperature

0x0104 Flow of the first waterway 0.1-200 L/Min 0.1/bit yes

0x0105 Flow of the second waterway 0.1-200 L/Min 0.1/bit yes

0x0106 Conductivity 0.1-500 μs/cm 0.1/bit yes

Compressor current
0x0107 0-50 A 0.1/bit yes
（Three-phase average）

0x0108 Low temp. water pump current 0-50 A 0.1/bit yes

0x0109 High temp. water pump current 0-50 A 0.1/bit yes

13
 CWFL-10000/12000/15000 Series

4. Read only parameter（state）

Read-only
Register
Description Bit definition
address
Bit7(MSb) Retain
Bit6 Retain

Bit5 Retain

Bit4 Retain
MSByte
Bit3 Retain

Bit2 Alarm output relay 0：Off 1：On

Bit1 Conductivity lower limit relay 0：Off 1：On
Bit0(LSb) High temp. heating rod 0：Off 1：On
Relay output
0x0800 Bit7(MSb) High temp. water pump relay 0：Off 1：On
status
Bit6 High temp. refrigeration relay 0：Off 1：On
Bit5 Compressor crankcase heating 0：Off 1：On
Bit4 Low temp. heating rod 0：Off 1：On
LSByte Low temp. refrigerant solenoid
Bit3 0：Off 1：On
valve
Bit2 Condensing fan 0：Off 1：On
Bit1 Compressor relay 0：Off 1：On
Bit0(LSb) Low temp. water pump 0：Off 1：On
Bit7(MSb) Retain
Bit6 Retain
Bit5 Retain
Bit4 Retain
MSByte
Bit3 Retain
Bit2 Retain
Bit1 Retain

Digital input Bit0(LSb) Retain

0x0801
switch status Bit7(MSb) Retain
Bit6 Retain
Bit5 External input 0：No input 1：Input
Bit4 Refrigerant low pressure 0：No input 1：Input
LSByte
Bit3 Refrigerant high pressure 0：No input 1：Input
Bit2 Spare 2 0：No input 1：Input
Bit1 Spare 1 0：No input 1：Input
Bit0(LSb) Water level 0：No input 1：Input

Alarm status Bit7(MSb) Retain

0x0802 MSByte
（high 16-bit） Bit6 Retain

14
 CWFL-10000/12000/15000 Series

Bit5 Retain

Bit4 Backup switch 2 alarm 0：Correct 1：Error

Bit3 Backup switch 1 alarm 0：Correct 1：Error
Bit2 Retain

Bit1 Retain

Bit0(LSb) Retain

Bit7(MSb) Write administrator parameter error 0：Correct 1：Error

Bit6 Write user parameter error 0：Correct 1：Error
Bit5 Ultra-high exhaust temp. alarm 0：No alarm 1：Alarm
Bit4 Exhaust temp. sensor failure alarm 0：No alarm 1：Alarm
LSByte Bit3 Low water level alarm 0：No alarm 1：Alarm
Bit2 Ultra-low conductivity alarm 0：No alarm 1：Alarm
Bit1 Ultra-high conductivity alarm 0：No alarm 1：Alarm
High temp. system water temp.
Bit0(LSb) 0：No alarm 1：Alarm
sensor failure alarm
Low temp. system water temp.
Bit7(MSb) 0：No alarm 1：Alarm
sensor failure
Bit6 Room temp. sensor failure 0：No alarm 1：Alarm
Bit5 Refrigeration system low pressure 0：No alarm 1：Alarm

MSByte Bit4 Refrigeration system High pressure 0：No alarm 1：Alarm

Bit3 High temp. water pump overload 0：No alarm 1：Alarm
Bit2 Low temp. water pump overload 0：No alarm 1：Alarm
Bit1 Compressor overload 0：No alarm 1：Alarm
Bit0(LSb) Wrong phase and lacking phase 0：No alarm 1：Alarm
High temp. system ultra-high water
Alarm status Bit7(MSb) 0：No alarm 1：Alarm
0x0803 temp
（low 16-bit）
High temperature system water
Bit6 0：No alarm 1：Alarm
temperature ultrlow
Low temperature system water
Bit5 0：No alarm 1：Alarm
temperature ultrahigh
LSByte
Low temperature system ultralow
Bit4 0：No alarm 1：Alarm
water temperature
Bit3 Ultrahigh ambient temperature 0：No alarm 1：Alarm
Bit2 High temperature system flow fail 0：No alarm 1：Alarm
Bit1 Low temperature system flow fail 0：No alarm 1：Alarm
Bit0(LSb) Communication fail 0：No alarm 1：Alarm

5. Read/Write Registers(Use only when the external input

function is turned off)
Register address Description Range Default Unit Remark Symbol
0x0804 Chiller On/Off 0-1 -- 0：On，1：Off No

15
 CWFL-10000/12000/15000 Series

<8> Simple troubleshooting

Failure Failure Cause Approach

Check and ensure the power interface

Power cord is not plugged in place and the power plug is plugged in place
and in good contact
Open the electric box cover, check the
Machine turned on but unelectrified protective tube, replace with spare one
if necessary and check whether the
Fuse burnt-out
power supply voltage is stable; Check
and ensure the power interface and
the power plug are in good contact
Flow Alarm
Check the water level gauge display,
(controller displays E01 or E02) use a
Water level in the storage water tank is add water until the level shown in the
water pipe directly connect to the
too low green area; And check whether water
water outlet and inlet but still without
circulation pipe leaks
water flowing
Flow alarm occurs while running with
other equipment (controller displays
E01 or E02), but there is water flowing Water circulation pipes are blocked or
Check water circulation pipe
and no alarm when use a water pipe a pipe bending deformation.
directly connected to the chiller water
outlet and inlet.
Unpick and wash the dust gauze
Blocked dust gauze, bad thermolysis
regularly
To ensure a smooth ventilation
Poor ventilation for air outlet and inlet
for air outlet and inlet
To improve the power supply circuit or
Voltage is extremely low or astable
use a voltage regulator
Ultra-high temperature
Improper parameter settings on To reset controlling parameters or
alarm(controller displays E05 or E07)
thermostat restore factory settings
To ensure there is sufficient time
Switch the power frequently for refrigeration
(more than 5 minutes)
Reduce the heat load or use other
Excessive heat load
model with larger cooling capacity
To improve the ventilation to guarantee
Alarm for ultra-high room The working ambient
that the machine is running under
temperature(controller displays E03) temperature is too high for the chiller
40℃.
Water temperature is much lower than Increase water temperature or
Serious problem of condensate water
ambient temperature, high humidity to preserve heat for pipeline
Water drains slowly from outfall during
Injection port is not open Open the injection port
water changing

16
 CWFL-10000/12000/15000 Series

Attachment – Schematic

17