16.
IC PROTECTOR
Printer control board
Date: 2013/11/19
Venta de Manuales Tecnico e Instalacion de Firmware: Hugo Luis Escalante Celular: 70865338
bizhub 754e/654e K TROUBLESHOOTING > 16. IC PROTECTOR
16. IC PROTECTOR
16.1 Outline
• To increase product safety, this MFP has an IC protector (ICP) installed in each board. ICP is a component that protects IC. If the amount of
the current supplied to the electrical parts such as motor exceeds the set level, ICP trips to protect IC from over current.
The following list contains ICP installed in each board, related devices, and symptoms that occur when ICP trips.
16.2 IC protector list
16.2.1 bizhub 754e/654e
(1) Printer control board
When ICP trips
ICP No. Symbol Target part name Trouble code and
Symptom in each load
others
ICP1 - Printer control board No operation -
Power source for DC/DC (24 V -> 3.3 V)
ICP2 PFTDB Paper feed/transport drive board No operation -
PS53 Waste toner box set sensor -
PEIB/1 Tray1 paper empty indicator board -
PEIB/2 Tray2 paper empty indicator board -
ICP3 FM9 DC power supply cooling fan DC power supply cooling fan's failure to turn C5351
- Key counter Unable to be detected -
(Install Key Counter)
DEDB Dehumidifier drive board Internal (dehumidifying) heater is not warmed -
up
ICP6 M18 PC motor/K PC motor/K failure to turn C225B
M19 Developing motor/K Developing motor/K failure to turn C2259
ICP7 M1 Transfer belt motor Transfer belt motor's failure to turn C5104
ICP8 M38 Cleaning brush motor Cleaning brush motor failure to turn C2257
ICP9 M30 Fusing motor Fusing motor failure to turn C3201
ICP10 TCB/K Toner cartridge set board/K The output from the toner cartridge set board -
does not change (remains Low).
(Install Toner Cartridge.)
ICP11 - Printer control board No 5 V output from the printer control board. -
Power source for DC/DC (24 V -> 5 V) (5 V is supplied to the front bottom door switch.)
ICP12 - Analog within the board As no power is supplied to the front bottom door -
MS3 Front bottom door switch switch, the front door remains open. -
IDCS/Fr IDC sensor/Fr -
TEMS4 Heating roller temperature sensor/4 -
PZS/K Toner empty sensor/K -
ICP13 PFTDB Paper feed/transport drive board Feed section jam -
ICP14 PHRYB PH relay board 5 V power cannot be supplied to the PH relay -
board
ICP15 PS51 1st transfer pressure sensor/K Transfer belt pressure welding alienation C2152
TEM/HUMS Temperature/humidity sensor The output from the Temp. and Humidity sensor -
does not change.
(The values displayed in [Service Mode] ->
[State Confirmation] -> [Temp. Humidity] do not
change.)
PS41 Fusing loop sensor/Fr The output from the fusing loop sensor/Fr or -
PS42 Fusing loop sensor/Rr fusing loop sensor/Rr does not change -
(remains Hi). (color shift or smear on paper
occurs.)
PS55 Fusing pressure home sensor Fusing pressure roller separation failure C3101
PS56 Heating roller rotation sensor Heating roller assy failure to turn C3102
PS54 Waste toner full sensor The output from the waste toner full sensor -
does not change (remains Low)
PS23 Waste toner lock sensor Waste toner transport motor failure to turn C2204
- IH power supply IH malfunction (CPU) C3B02
IH malfunction (monitor) C3B03
- ICP10 (TCB/K) The output from the new parts and installation -
detection board does not change (remains Low)
(Install Toner Cartridge.)
ICP16 PFTDB Paper feed/transport drive board Paper feed communication error C0002
ICP17 PHRYB PH relay board PH communication error C4002
K-206
Venta de Manuales Tecnico e Instalacion de Firmware: Hugo Luis Escalante Celular: 70865338
bizhub 754e/654e K TROUBLESHOOTING > 16. IC PROTECTOR
When ICP trips
ICP No. Symbol Target part name Trouble code and
Symptom in each load
others
ICP18 M1 Transfer belt motor Transfer belt motor's failure to turn C5104
Faulty image (uneven density) -
M18 PC motor/K PC motor/K failure to turn C225B
Faulty image (uneven density) -
ICP19 M4 Exit motor Paper exit section jam -
M33 Switchback motor -
ICP20 HV1 High voltage unit/1 Occurrence of warning code P-5/P-9/P-27
Faulty image (No images are printed on a -
paper)
HV3 High voltage unit/3 2nd transfer section jam -
ICP21 HV2 High voltage unit/2 Occurrence of warning code P-5/P-9
Faulty image (low image density) -
SD1 Gate switch solenoid Paper exit section jam -
ICP22 FM101 Tucking fan/Md Unable to make a copy (LED of Start Key blinks -
FM102 Tucking fan/Rr in red.) -
FM103 Tucking fan/Fr -
FM2 Paper cooling fan/out -
FM6 Ozone ventilation fan -
FM13 Paper cooling fan/in -
FM3 IH coil cooling fan -
FM7 Toner suction fan -
ICP23 M12 Toner supply motor/K Black TCR sensor-Abnormally low toner C2557/C255C
density/Adjustment failure
ICP24 M21 1st transfer pressure motor Transfer belt pressure welding alienation C2152
M14 Toner cartridge motor/CK Black TCR sensor-Abnormally low toner C2557/C255C
density/Adjustment failure
FM10 IH power supply cooling fan IH power supply cooling fan's failure to turn C5304
ICP25 M29 Fusing pressure motor Fusing roller separation failure C3101
ICP26 DCPU DC power supply No operation -
DFCB DF control board -
SCDB Scanner drive board -
K-207
