TA7784P LINEAR INTEGRATED CIRCUIT
DUAL PRE-AMPLIFIER FOR AUTO-
REVERSE
DESCRIPTION
The Contek TA7784P is a dual pre-amplifier for auto-reverse
type and W-cassette type tape player. This IC contains dual
pre-amplifier, forward/ reverse control switches and metal/
normal tape equalizer control switches.
FEATURES
*High voltage gain: G VO=95dB(typ) at Vcc=6V f=1kHz
*Wide operating supply voltage( VCC= 3.5V~15V)
*No input coupling capacitor
DIP-16
*Low noise( VNI=1mVrms(typ) at Rg=600W,
BW=20Hz~20kHz, NAB EQ)
BLOCK DIAGRAM
Contek Microelectronics Co.,Ltd. 1
[Link] E-mail:sales@[Link]
CONTEK
TA7784P LINEAR INTEGRATED CIRCUIT
ABSOLUTE MAXIMUN RATINGS (Ta=25 C)
PARAMETER SYMBOL VALUE UNIT
Supply Voltage Vcc 16 V
Power Dissipation PD 750 mW
Operating Temperature Topr -25~75 C
Storage Temperature Tstg -55~150 C
Note: de-rated above Ta=25 C in the proportion of 6mW/ C.
ELECTRICAL CHARACTERISTICS(Ta=25 C,Vcc=6V,Rg=600 W, f=1kHz, unless otherwise specified
PARAMETER SYMBOL TEST TEST MIN TYP MAX UNIT
CIRCUIT CONDITIONS
Quiescent Current ICCQ1 1 VIN=0, Normal EQ 5.5 mA
ICCQ1 1 VIN=0, Metal EQ 7 11
Open Loop Voltage Gain GVo 1 Cf=100mF,Rf=0 95 dB
Maximum Output Voltage VOM 1 THD=0.5% 1.1 1.5 Vrms
Total Harmonic Distortion THD 1 Vout=0.5Vrms 0.035 0.12 %
Equivalent Input Noise VNI 1 Rg=620W,NAB 1 1.7 mVrms
BW:20Hz~20kHz
Metal EQ
Ripple Rejection RR 1 f=100Hz,Vin=1Vrms 55 dB
Cross Talk CT 1 Vout=0dBm 50 60 dB
Forward/ Reverse Cross CT(F/R) Vout=0dBm 60 70 dB
Talk
Contek Microelectronics Co.,Ltd. 2
[Link] E-mail:sales@[Link]
CONTEK
TA7784P LINEAR INTEGRATED CIRCUIT
TEST CIRCUIT(Pin Configuration and DC Voltage
C8
Ch1
R f =180k W R NF =330k W 4.7 mF
Out
Vcc
RL=10kW
SW1-1
R3=12k W
C10
C6 100 mF
C f =22 mF 100 mF 0.01 mF R4=18k W
a 6 4 2 1
b
SW2-1
5
Vcc
AMP
R6
Rg M
7
SG R7 C3
EQ SW 15
N
C1 =100 mF
9 Bias
47k W F
R8 C4
F/R SW 3
13 R
1 mF
R9
620 W x4
C5 AMP
11
Contek
SW2-2
b 12 10 14 16 8
a
C7 R4=18k W
C f =22 mF 100 mF
0.01 mF
SW1-2 R3=12k W
C8 Ch2
4.7 mF Out
RL =10kW
R f =180k W R NF =330k W
*Gvo Test: SW1-1, 2: Off, SW2-1, 2:B
Pin Configuration and DC Voltage ( Vcc=6V, Ta=25 C, Unless otherwise specified)
DC VOLTAGE
PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
NO.
VALUE Vcc 2.3 Vcc/GND 2.2 2.2 2.2 2.2 GND 2.2 NC 2.2 2.2 2.2 2.2 Vcc/GND 2.2
(V)
Contek Microelectronics Co.,Ltd. 3
[Link] E-mail:sales@[Link]
CONTEK
TA7784P LINEAR INTEGRATED CIRCUIT
APPLICATION INFORMATION
[Link]/Reverse select switch
1 Threshold voltage: Pin 3 is coupled to the base of IE=100 mA
Q1( PNP-Tr) as Fig. 1 The threshold voltage is 0~0.3V
at reverse stage and is 1.1~Vcc at the Forward stage.
2 The recommended Forward/ Reverse select circuit is
3
shown in Fig. 2 I3
3 I3(Fig. 1)=12mA,Ta=25 C
Fig 1
[Link] control switch
Pin 15 is coupled to the base of Q2 ( PNP Tr) as shown 1.5V
Fig. 3. The emitter potential of Q2 is 2.6V. The threshold
voltage is 21~Vcc at Metal EQ stage and is 0~1.2V at the F
30~50W
Normal EQ stage. 3
R
1mF
Fig 2
3.C2/C3/C4/C5
Capacitor C2~C5 may be required for preventing a
instability caused by the pattern layout or interference of 2.6V
external high frequency signal.
15
Fig 3
Contek Microelectronics Co.,Ltd. 4
[Link] E-mail:sales@[Link]
CONTEK
This datasheet has been downloaded from:
[Link]
Datasheets for electronic components.
