MODEL Ventable, pilot-operated, balanced piston relief valve
RVCA SERIES 1 / CAPACITY: 60 L/min. / CAVITY: T-11A
sunhydraulics.com/model/RVCA
Ventable, pilot-operated, balanced piston relief cartridges are normally closed pressure regulating valves. When the
pressure at the inlet (port 1) reaches the valve setting, the valve starts to open to tank (port 2), throttling flow to
CONFIGURATION regulate the pressure. They provide a vent port (port 3) that connects between the main piston and pilot stage to
provide for remote control by other pilot or 2-way valves. These valves are accurate, have low pressure rise vs.
L Control Standard Screw Adjustment flow, they are smooth and quiet, and are moderately fast.
A Adjustment 100 - 3000 psi (7 - 210 bar),
Range 1000 psi (70 bar) Standard
TECHNICAL DATA NOTE: DATA MAY VARY BY CONFIGURATION. SEE CONFIGURATION SECTION.
Setting
Cavity T-11A
N Seal Material Buna-N
Series 1
(none) Material/Coating Standard Material/Coating
Capacity 60 L/min.
Factory Pressure Settings Established at 15 L/min.
Maximum Operating Pressure 350 bar
Control Pilot Flow 0,11 - 0,16 L/min.
Maximum Valve Leakage at 110 SUS (24 cSt) 30 cc/min.@70 bar
Response Time - Typical 10 ms
Adjustment - No. of CW Turns from Min. to Max. setting 5
Valve Hex Size 22,2 mm
Valve Installation Torque 41 - 47 Nm
Adjustment Screw Internal Hex Size 4 mm
Locknut Hex Size 15 mm
Locknut Torque 9 - 10 Nm
Seal kit - Cartridge Buna: 990011007
Seal kit - Cartridge EPDM: 990011014
Seal kit - Cartridge Polyurethane: 990011002
Seal kit - Cartridge Viton: 990011006
Model Weight 0.16 kg.
NOTES For Series 1 cartridges configured with an O control (panel mount handknob), a .75 in. (19 mm) diameter hole is required in the panel.
c 2019 Sun Hydraulics 1 of 2
CONFIGURATION OPTIONS Model Code Example: RVCALAN
CONTROL (L) ADJUSTMENT RANGE (A) SEAL MATERIAL (N) MATERIAL/COATING
L Standard Screw Adjustment A 100 - 3000 psi (7 - 210 bar), 1000 psi N Buna-N Standard Material/Coating
C Tamper Resistant - Factory Set (70 bar) Standard Setting E EPDM /AP Stainless Steel, Passivated
K Handknob W 150 - 4500 psi (10,5 - 315 bar), 1000 V Viton /LH Mild Steel, Zinc-Nickel
O Handknob with Panel Mount psi (70 bar) Standard Setting
B 50 - 1500 psi (3,5 - 105 bar), 1000 psi
(70 bar) Standard Setting
C 150 - 6000 psi (10,5 - 420 bar), 1000
psi (70 bar) Standard Setting
D 25 - 800 psi (1,7 - 55 bar), 400 psi (28
bar) Standard Setting
E 25 - 400 psi (1,7 - 28 bar), 200 psi (14
bar) Standard Setting
TECHNICAL FEATURES
A remote pilot relief on port 3 (vent) will control the valve below its own setting.
Will accept maximum pressure at port 2; suitable for use in cross port relief circuits. If used in cross port relief circuits, consider spool leakage.
Main stage orifice is protected by a 150-micron stainless steel screen.
Not suitable for use in load holding applications due to spool leakage.
Back pressure on the tank port (port 2) is directly additive to the valve setting at a 1:1 ratio.
Cartridges configured with EPDM seals are for use in systems with phosphate ester fluids. Exposure to petroleum based fluids, greases and lubricants will damage
the seals.
Incorporates the Sun floating style construction to minimize the possibility of internal parts binding due to excessive installation torque and/or cavity/cartridge
machining variations.
PERFORMANCE CURVES
c 2019 Sun Hydraulics 2 of 2
