VOCATIONAL PRACTICALS

QUESTION BANK
(With Effect from the Academic year 2018-19)

(COURSE CODE: 321)

State Institute of Vocational Education

O/o the Commissioner of Intermediate Education,
Telangana State, Hyderabad
&
Board of Intermediate Education
Telangana State, Hyderabad

1
List of Participants
1. Sri K. Prasad, Junior Lecturer,
Government Vocational Junior College
Hyderabad.
2. Sri Paul Prasad, MTSJL
Government Junior College Boys Falaknuma
Hyderabad.

2
 ELECTRICAL TECHNICIAN
FIRST YEAR
QUESTION BANK
Paper I: Basic Electrical Lab
Time: 3hrs Max. Marks: 50
SECTION-I (Major Experiment)
Note: (i) Answer any one Question.
(ii) Each Question carries 20 mark 1X20=20 Marks

1. Verify Ohms law by using ammeter, voltmeter in DC circuit or Low

Voltage AC Circuit.
2. Verify characteristics of DC series circuit.
3. Verify resistance laws by using ohm meter
4. Measure the power of given load by voltmeter and ammeter.
5. Measure the power factor of given load by voltmeter, ammeter and
wattmeter.
6. Measure the energy consumed by a load using energy meter.
7. Test the energy meter.
8. Draw the magnetic lines of a bar magnet.
9. Draw the magnetic lines of a U magnet.
[Link] the given battery.
SECTION-II (Minor Experiment)
Note: (i) Answer any One Question
(ii) Each Question carries 10 marks 1X10=10 Marks

[Link] the circuit diagram to prove Ohms law.

[Link] two loads in parallel and measure voltage using 220V ac supply
(use two 100W bulbs)
[Link] the resistance of given equipment by Ohm meter (use bulb,
electric iron, choke etc as load and multimeter as ohm meter)

3
 [Link] the power of given load.
[Link] the importance of power factor improvement.
[Link] the internal connections of energy meter.
[Link] the energy meter to a given load.
18. Draw the magnetic lines for a given magnet.
[Link] the connections for charging of a battery.
[Link] the voltage of given battery.
SECTION-III (Identification/ Spotting)
Note: (i) Answer any Five Questions.
(ii) Each Question carries 2 marks 5X2=10 Marks

[Link] of given electrical measuring instrument and mention its

applications.
[Link] the type of connections used in series/decoration bulbs.
[Link] the type of resistance used in fan regulator.
[Link] the names of instruments used in testing of battery.
[Link] the energy consumed by an electric iron of 1250W, 250V AC
Supply when used for TWO hours.
[Link] type of magnet is used in ceiling fan and toys?
[Link] 2 HP into watts; 2 kW into watts.
[Link] type of batteries is used in two wheelers?
[Link] maintenance methods of battery.
[Link] the examples for inductance and capacitance.
SECTION-IV
Record 5 marks
Viva- Voice 5 Marks

4
 ELECTRICAL TECHNICIAN
FIRST YEAR
MODEL QUESTION PAPER
Paper I: Basic Electrical Lab
Time: 3hrs Max. Marks: 50
SECTION-I (Major Experiment)
Note: (i) Answer any one Question.
(ii) Each Question carries 20 mark 1X20=20 Marks

3. Verify resistance laws by using ohm meter

4. Measure the power of given load by voltmeter and ammeter.
5. Measure the power factor of given load by voltmeter, ammeter and
wattmeter.
6. Measure the energy consumed by a load using energy meter.
7. Test the energy meter.

SECTION-II (Minor Experiment)

Note: (i) Answer any One Question
(ii) Each Question carries 10 marks 1X10=10 Marks

[Link] the circuit diagram to prove Ohms law.

[Link] two loads in parallel and measure voltage using 220V ac supply
(use two 100W bulbs)
[Link] the resistance given equipment by Ohm meter (use bulb, electric
iron, choke etc as load and multimeter as ohm meter)
[Link] the power of given load.
[Link] the importance of power factor improvement.

SECTION-III (Identification/ Spotting)

Note: (i) Answer any Five Questions.
(ii) Each Question carries 2 marks 5X2=10 Marks

5
 21. Identification of given electrical measuring instrument and mention its
applications.
22. Name of the type of connections used in series/decoration bulbs.
23. Name the type of resistance used in fan regulator.
24. Write the names of instruments used in testing of battery.
25. Calculate the energy consumed by an electric iron of 1250W, 250V AC
Supply when used for TWO hours.

SECTION-IV
Record 5 marks
Viva- Voice 5 Marks

Note: The serial numbers of the questions mentioned above are the serial number in
question bank. In practical examination only the serial number of the question will be
given. The examiner shall decode it with the question bank and give the questions.

6
 ELECTRICAL TECHNICIAN
FIRST YEAR
SCHEME OF VALUATION
Paper I: Basic Electrical Lab
Time: 3hrs Max. Marks: 50
Section – I (Major Experiment) 1X 20 = 20 Marks
Aim, Tools, Materials :5 marks
Circuit Diagram :5 marks
Experiment :5 marks
Presentation and Result :5 marks
Section – II (Minor Experiment) 1X 10 = 10 Marks

Diagram/circuit : 5 marks;

Order of performing experiment/explanation : 5 marks

Section – III (Identification / Spotting) 5X 2 = 10 Marks

Select any FIVE practical from Q no 21 to 30

SECTION-IV
Record 5 marks
Viva- Voice 5 Marks

7
 ELECTRICAL TECHNICIAN
FIRST YEAR
QUESTION BANK
Paper II: Engineering Drawing

Time: 3hrs Max. Marks: 50

SECTION-I (Major Experiment)
Note: (i) Answer any one Question.
(ii) Each Question carries 20 mark 1X20=20 Marks

1. Draw Pipe Earthing and Plate earthing

2. Draw the internal connections and constructional details of 1 ph energy
meter
3. Draw the connection diagram of 1ph energy meter with 4 way
distribution board
4. Draw the electrical symbols for One way switch, two way switch, DPIC,
TPIC, Bell Switch, Batten holder, Fuse, Earth, Aerial, MCB
5. Draw symbols for Cell, Battery, AC generator, Transformer, Fan
regulator, Lamp, Socket, LED, Capacitor, Resistor.
6. Draw a parabola of 40mm base, 70mm height by tangent method
7. Draw an Ellipse of 40mm base, 80mm height by rectangle method
8. Draw HYPERBOLA at a given the position of point
9. Draw the projections of a rectangular cube of 70mm x 50mm x 30mm
[Link] an ellipse of 80mm major axis and 40mm minor axis.

SECTION-II (Minor Experiment)

Note: (i) Answer any One Question
(ii) Each Question carries 10 marks 1X10=10 Marks

[Link] a tangent for a circle of 25mm radius

8
 [Link] a Hexagon for a circle of 50mm radius
[Link] a common tangent for two circles of 50mm radius
[Link] a Pentagon of side 40mm
[Link] an OCTAGON given a side of 80mm
[Link] a Heptagon for a circle of 60mm radius
[Link] a OCTAGON with a side of 40mm
[Link] a PENTAGON for a circle of 50mm radius
[Link] a HEXAGON inside the circle of 60mm radius
[Link] a Hexagon outside the circle of 60mm radius
SECTION-III (Identification/ Spotting)
Note: (i) Answer any Five Questions.
(ii) Each Question carries 2 marks 5X2=10 Marks

[Link] the following with normal lettering of size 15mm

VOCATIONAL COURSE
[Link] the following with normal lettering of size 15mm
ELECTRICAL ENGINEERING
[Link] a 8cm line into 10 equal parts
[Link] aligned system of dimensioning on a square of 40mm.
[Link] a line of 9cm length.
[Link] a tangent for a circle of 50mm dia.
[Link] a rectangle of 8cm x 4cm in 8 parts.
[Link] a equilateral triangle of 5cm side.
[Link] a perpendicular line to a straight line of 6cm.
[Link] the list of drawing instruments.
SECTION-IV
Record 5 marks
Viva- Voice 5 Marks

9
 ELECTRICAL TECHNICIAN
FIRST YEAR
MODEL QUESTION PAPER
Paper II: Engineering Drawing
Time: 3hrs Max. Marks: 50
SECTION-I (Major Experiment)
Note: (i) Answer any one Question.
(ii) Each Question carries 20 mark 1X20=20 Marks

1. Draw Pipe Earthing and Plate earthing

2. Draw the internal connections and constructional details of 1 ph energy
meter
3. Draw the connection diagram of 1ph energy meter with 4 way
distribution board
4. Draw the electrical symbols for One way switch, two way switch, DPIC,
TPIC, Bell Switch, Batten holder, Fuse, Earth, Aerial, MCB
5. Draw symbols for Cell, Battery, AC generator, Transformer, Fan
regulator, Lamp, Socket, LED, Capacitor, Resistor.

SECTION-II (Minor Experiment)

Note: (i) Answer any One Question
(ii) Each Question carries 10 marks 1X10=10 Marks

[Link] a Heptagon for a circle of 60mm radius

[Link] a OCTAGON with a side of 40mm
[Link] a PENTAGON for a circle of 50mm radius
[Link] a HEXAGON inside the circle of 60mm radius
[Link] a Hexagon outside the circle of 60mm radius

10
 SECTION-III (Identification/ Spotting)
Note: (i) Answer any Five Questions.
(ii) Each Question carries 2 marks 5X2=10 Marks

26. Draw a tangent for a circle of 50mm dia.

[Link] a rectangle of 8cm x 4cm in 8 parts.
[Link] a equilateral triangle of 5cm side.
[Link] a perpendicular line to a straight line of 6cm.
[Link] a 5cm line into 3 parts.

SECTION-IV
Record 5 marks
Viva- Voice 5 Marks

Note: The serial numbers of the questions mentioned above are the serial number in
question bank. In practical examination only the serial number of the question will be
given. The examiner shall decode it with the question bank and give the questions.

11
 ELECTRICAL TECHNICIAN
FIRST YEAR
SCHEME OF VALUATION
Paper II: Engineering Drawing
Time: 3hrs Max. Marks: 50
Section – I (Major Experiment) 1X 20 = 20 Marks
Aim, Tools, Materials :5 marks
Circuit Diagram :5 marks
Experiment :5 marks
Presentation and Result :5 marks
Section – II (Minor Experiment) 1X 10 = 10 Marks

Diagram/circuit : 5 marks;

Order of performing experiment/explanation : 5 marks

Section – III (Identification / Spotting) 5X 2 = 10 Marks

Select any FIVE practical from Q no 21 to 30

SECTION-IV
Record 5 marks
Viva- Voice 5 Marks

12
 ELECTRICAL TECHNICIAN
FIRST YEAR
QUESTION BANK
Paper III: Electrical Wiring and Workshop

Time: 3hrs Max. Marks: 50

SECTION-I (Major Experiment)
Note: (i) Answer any one Question.
(ii) Each Question carries 20 mark 1X20=20 Marks

1. Install a surface conduit wiring for one lamp controlled by one switch.
2. Install a surface conduit wiring for one lamp and one socket by separate
switch.
3. Connect two lamps in series in casing capping wiring.
4. Install a bed room lighting in casing capping wiring.
5. Install a stair case wiring in surface conduit wiring.
6. Prepare a distribution board for FOUR sub-circuits.
7. Install Godown wiring in conduit wiring system.
8. Test the given wiring installation by using ohmmeter/megger/test lamp.
9. Install a pipe earthing.
[Link] connections for a fluorescent lamp.
SECTION-II (Minor Experiment)
Note: (i) Answer any One Question
(ii) Each Question carries 10 marks 1X10=10 Marks

[Link] a straight joint by using 3/20 copper cable

[Link] a T- joint with 1/18 wire.
[Link] the three switches and one socket on a given switch board.
[Link] a married joint by using 14/0.3 (1sq mm) copper cable
[Link] a T- joint with 7/20 wire.
[Link] a stair case wiring by using conduits.

13
 [Link] a pig tail joint by using single strand aluminium cable
[Link] a straight joint by using GI wire.
[Link] a test lamp.
20. Fix a fan regulator on a switch board and make proper connections.

SECTION-III (Identification/ Spotting)

Note: (i) Answer any Five Questions.
(ii) Each Question carries 2 marks 5X2=10 Marks

[Link] the size of given wire by using SWG

[Link] the given cables/wires and write their applications.
[Link] are the tools used by an electrician?
[Link] to prevent Electric shock?
[Link] the terminals in the given cable/3-pin plug top.
[Link] the main materials and accessories for conduit wiring.
[Link] is the purpose of fuse?
[Link] the soldering iron.
[Link] are the advantages of LED lamps.
[Link] examples for light load and power load.

SECTION-IV
Record 5 marks
Viva- Voice 5 Marks

14
 ELECTRICAL TECHNICIAN
FIRST YEAR
MODEL QUESTION PAPER
Paper III: Electrical Wiring and Workshop
Time: 3hrs Max. Marks: 50
SECTION-I (Major Experiment)
Note: (i) Answer any one Question.
(ii) Each Question carries 20 mark 1X20=20 Marks

2. Install a surface conduit wiring for control one lamp and one socket by
separate switch.
3. Connect two lamps in series in casing capping wiring.
4. Install a bed room lighting in casing capping wiring.
5. Install a stair case wiring in surface conduit wiring.
6. Prepare a distribution board for FOUR sub-circuits.

SECTION-II (Minor Experiment)

Note: (i) Answer any One Question
(ii) Each Question carries 10 marks 1X10=10 Marks

[Link] a stair case wiring by using conduits.

[Link] a pig tail joint by using single strand aluminium cable
[Link] a straight joint by using GI wire.
[Link] a test lamp.
Fix a fan regulator on a switch board and make proper connections.

SECTION-III (Identification/ Spotting)

Note: (i) Answer any Five Questions.
(ii) Each Question carries 2 marks 5X2=10 Marks

26. List the main materials and accessories for conduit wiring.
[Link] is the purpose of fuse?

15
 [Link] the soldering iron.
[Link] are the advantages of LED lamps.
[Link] examples for light load and power load.

SECTION-IV
Record 5 marks
Viva- Voice 5 Marks

Note: The serial numbers of the questions mentioned above are the serial number in
question bank. In practical examination only the serial number of the question will be
given. The examiner shall decode it with the question bank and give the questions.

16
 ELECTRICAL TECHNICIAN
FIRST YEAR
SCHEME OF VALUATION
Paper III: Electrical Wiring and Workshop
Time: 3hrs Max. Marks: 50
Section – I (Major Experiment) 1X 20 = 20 Marks
Aim, Tools, Materials :5 marks
Circuit Diagram :5 marks
Experiment :5 marks
Presentation and Result :5 marks
Section – II (Minor Experiment) 1X 10 = 10 Marks

Diagram/circuit : 5 marks;

Order of performing experiment/explanation : 5 marks

Section – III (Identification / Spotting) 5X 2 = 10 Marks

Select any FIVE practical from Q no 21 to 30

SECTION-IV
Record 5 marks
Viva- Voice 5 Marks

17
 ELECTRICAL TECHNICIAN
SECOND YEAR
QUESTION BANK
Paper I: Electrical Machines Lab
Time: 3hrs Max. Marks: 50
SECTION-I (Major Experiment)
Note: (i) Answer any one Question.
(ii) Each Question carries 20 mark 1X20=20 Marks

1. Identify the terminals and measure the resistance of windings of DC

machine by multi meter.
2. Identify the various parts and connect D.C Shunt motor by 3-point starter.
3. Identify the various parts and connect D.C Compound motor by 4-point
starter.
4. Measure the Power by using Two Watt meter method in a 3-Ph circuit or
load.
5. Identify the various parts and connect 3-Ph Induction motor by DOL
starter.
6. Identify the various parts and connect 3-Ph Induction motor by STAR-
DELTA starter.
7. Connect, start, run and reverse the direction of rotation of 1-ph capacitor
start motor. And observe the current and speed at different loads .
8. Connect, start, run the shaded pole motor (cooler pump motor). .
9. Connect, start, run the universal motor (mixer grinder motor). And
observe the current and speed at different loads.
[Link] the power in RLC circuits (Use 1-ph Induction motor /ceiling fan).

SECTION-II (Minor Experiment)

Note: (i) Answer any One Question

18
 (ii) Each Question carries 10 marks 1X10=10 Marks

[Link] the speed control methods of a DC motor.

[Link] the losses in a transformer. Draw the circuit diagram for OC or SC
test of a single phase transformer.
[Link] the terminals in 3 - point starter and draw internal connections.
[Link] the terminals in 4 - point starter and draw internal connections.
[Link] the terminals in 3 – phase induction motor.
[Link] and run the 1 – ph permanent capacitor motor (ceiling fan/table
fan).
[Link] and run the shaded pole motor (cooler pump or small exhaust
fan).
18. Connect and run universal motor (mixer grinder motor).
[Link] an extra capacitor a single phase permanent capacitor motor and
note the changes.
[Link] the power consumed by an Universal Motor by using
Voltmeter and Ammeter.

SECTION-III (Identification/ Spotting)

Note: (i) Answer any Five Questions.
(ii) Each Question carries 2 marks 5X2=10 Marks

[Link] the applications of DC motors.

[Link] is step up and step down transformer.
[Link] the 1 – phase and 3 – phase voltages in India.
[Link] the STAR connection and state its applications.
[Link] the DELTA connection and state its applications.
[Link] transformer becomes hot while working?
[Link] are the applications of 3 – phase induction motors?

19
[Link] the function of starter in AC motor?
[Link] the types of power stations.
30. What is the purpose of Substations?

SECTION-IV
Record 5 marks
Viva- Voice 5 Marks

20
 ELECTRICAL TECHNICIAN
SECOND YEAR
MODEL QUESTION PAPER
Paper I: Electrical Machines Lab
Time: 3hrs Max. Marks: 50
SECTION-I (Major Experiment)
Note: (i) Answer any one Question.
(ii) Each Question carries 20 mark 1X20=20 Marks.

1. Identify the terminals and measure the resistance of windings of DC

machine by multi meter.
2. Identify the various parts and connect D.C Shunt motor by 3-point starter.
3. Identify the various parts and connect D.C Compound motor by 4-point
starter.
4. Measure the Power by using Two Watt meter method in a 3-Ph circuit or
load.
5. Identify the various parts and connect 3-Ph Induction motor by DOL
starter.
SECTION-II (Minor Experiment)
Note: (i) Answer any One Question
(ii) Each Question carries 10 marks 1X10=10 Marks

[Link] the speed control methods of a DC motor.

[Link] the losses in a transformer. Draw the circuit diagram for OC or SC
test of a single phase transformer.
[Link] the terminals in 3 - point starter and draw internal connections.
[Link] the terminals in 4 - point starter and draw internal connections.
[Link] the terminals in 3 – phase induction motor

21
 SECTION-III (Identification/ Spotting)
Note: (i) Answer any Five Questions.
(ii) Each Question carries 2 marks 5X2=10 Marks

[Link] transformer becomes hot while working?

[Link] are the applications of 3 – phase induction motors?
[Link] the function of starter in AC motor?
[Link] the types of power stations.
[Link] is the purpose of Substations?

SECTION-IV
Record 5 marks
Viva- Voice 5 Marks

Note: The serial numbers of the questions mentioned above are the serial number in
question bank. In practical examination only the serial number of the question will be
given. The examiner shall decode it with the question bank and give the questions.

22
 ELECTRICAL TECHNICIAN
SECOND YEAR
SCHEME OF VALUATION
Paper I: Electrical Machines Lab
Time: 3hrs Max. Marks: 50
Section – I (Major Experiment) 1X 20 = 20 Marks
Aim, Tools, Materials :5 marks
Circuit Diagram :5 marks
Experiment :5 marks
Presentation and Result :5 marks
Section – II (Minor Experiment) 1X 10 = 10 Marks

Diagram/circuit : 5 marks;

Order of performing experiment/explanation : 5 marks

Section – III (Identification / Spotting) 5X 2 = 10 Marks

Select any FIVE practical from Q no 21 to 30

SECTION-IV
Record 5 marks
Viva- Voice 5 Marks

23
 ELECTRICAL TECHNICIAN
SECOND YEAR
QUESTION BANK
Paper II: Domestic Appliances Lab
Time: 3hrs Max. Marks: 50
SECTION-I (Major Experiment)
Note: (i) Answer any one Question.
(ii) Each Question carries 20 mark 1X20=20 Marks

1. Dismantling, re-assembling and troubleshooting of electric room heater

(rod type)
2. Dismantling, re-assembling and troubleshooting of ordinary OR automatic

electric iron
3. Dismantling, re-assembling and troubleshooting of electric stove

4. Dismantling, re-assembling and troubleshooting of electric geyser

5. Dismantling, re-assembling and troubleshooting of Table fan OR Ceiling

fan
6. Dismantling, re-assembling and troubleshooting of room air cooler

7. Dismantling, re-assembling and troubleshooting of Florescent Tube

8. Dismantling, re-assembling and troubleshooting of emergency light.

9. Testing of burnt/faulty motor like (ceiling fan, 3-ph motor and mixer

motor.
10. Make re-winding the given table fan

SECTION-II (Minor Experiment)

Note: (i) Answer any One Question
(ii) Each Question carries 10 marks 1X10=10 Marks

11. State general faults and testing methods in domestic appliances.

12. Identify the parts in given electric iron and name possible faults.
13. Identify the parts in given electric stove and name possible faults

24
 14. Identify the parts in given geyser and name possible faults
15. Identify the parts in given rice cooker and name possible faults
16. Dismantle and assemble table fan.
17. Dismantle and assemble ceiling fan
18. Collect name plate details of given appliances (any two)
19. Prepare the field coil for a mixer grinder motor.
20. Draw the connection diagram of an air cooler

SECTION-III (Identification/ Spotting)

Note: (i) Answer any Five Questions.
(ii) Each Question carries 2 marks 5X2=10 Marks

21. Identify the tools required for repair of domestic appliances.

22. Mention any FOUR domestic appliances and write their ratings.
23. State the function of a Thermostat.
24. Write the purpose of series testing board.
25. What are the precautions to be taken while using Immersion water
heater?
26. Identify the parts in given hair drier and draw its diagram.
27. What is the use of Microwave oven and name important parts.
28. Draw the ceiling fan.
29. Draw the internal connections of Emergency lamp.
30. What is the use of Inverter and UPS?

SECTION-IV
Record 5 marks
Viva- Voice 5 Marks

25
 ELECTRICAL TECHNICIAN
SECOND YEAR
MODEL QUESTION PAPER
Paper II: Domestic Appliances Lab
Time: 3hrs Max. Marks: 50
SECTION-I (Major Experiment)
Note: (i) Answer any one Question.
(ii) Each Question carries 20 mark 1X20=20 Marks

6. Dismantling, re-assembling and troubleshooting of room air cooler

7. Dismantling, re-assembling and troubleshooting of Florescent Tube

8. Dismantling, re-assembling and troubleshooting of emergency light.

9. Testing of burnt/faulty motor like (ceiling fan, 3-ph motor and mixer

motor
10. Make re-winding the given table fan.

SECTION-II (Minor Experiment)

Note: (i) Answer any One Question
(ii) Each Question carries 10 marks 1X10=10 Marks

15. State general faults and testing methods in domestic appliances.

16. Identify the parts in given electric iron and name possible faults.

17. Identify the parts in given electric stove and name possible faults

18. Identify the parts in given geyser and name possible faults

19. Identify the parts in given rice cooker and name possible faults

SECTION-III (Identification/ Spotting)

Note: (i) Answer any Five Questions.
(ii) Each Question carries 2 marks 5X2=10 Marks

21. Identify the tools required for repair of domestic appliances.

22. Mention any FOUR domestic appliances and write their ratings.

26
 23. State the function of a Thermostat.

24. Write the purpose of series testing board.

25. What are the precautions to be taken while using Immersion water

heater?

SECTION-IV
Record 5 marks
Viva- Voice 5 Marks

Note: The serial numbers of the questions mentioned above are the serial number in
question bank. In practical examination only the serial number of the question will be
given. The examiner shall decode it with the question bank and give the questions.

27
 ELECTRICAL TECHNICIAN
SECOND YEAR
SCHEME OF VALUATION
Paper II: Domestic Appliances Lab
Time: 3hrs Max. Marks: 50
Section – I (Major Experiment) 1X 20 = 20 Marks
Aim, Tools, Materials :5 marks
Circuit Diagram :5 marks
Experiment :5 marks
Presentation and Result :5 marks
Section – II (Minor Experiment) 1X 10 = 10 Marks

Diagram/circuit : 5 marks;

Order of performing experiment/explanation : 5 marks

Section – III (Identification / Spotting) 5X 2 = 10 Marks

Select any FIVE practical from Q no 21 to 30

SECTION-IV
Record 5 marks
Viva- Voice 5 Marks

28
 ELECTRICAL TECHNICIAN
SECOND YEAR
QUESTION BANK

Paper III: Electrical Estimation and Utilization Lab

Time: 3hrs Max. Marks: 50

SECTION-I (Major Experiment)
Note: (i) Answer any one Question.
(ii) Each Question carries 20 mark 1X20=20 Marks

1. Take the measurements of residential building and prepare wiring layout.

2. Take the measurements of shop and prepare the wiring layout.
3. Take the measurements of college block and prepare wiring layout.
4. Prepare the detailed estimate in standard format for installing surface
conduit wiring in a small residential building.
5. Prepare the detailed estimate in standard format for installing casing and
capping wiring in a small shop.
6. Install a casing capping/surface conduit wiring in a model building/ class
room, make the list of materials.
7. Prepare an estimate in standard proforma for installation of 5-HP motor
in a small work shop. .
8. Prepare a detailed schedule of material, layout to install an OH
distribution line about 2 km along with street lights (use nearby street
light/distribution line).
9. Prepare detailed list of materials and accessories (schedule) of plinth
mounted transformer.
[Link] detail schedule of material for Pipe earthing or Plate earthing.

29
 SECTION-II (Minor Experiment)
Note: (i) Answer any One Question
(ii) Each Question carries 10 marks 1X10=10 Marks

[Link] connections of 1-ph service mains, main board (load 1000W)

[Link] connections of 3-ph main board and distribution board (load
4500W)
[Link] a motor control panel for controlling of 1-ph motors.
[Link] the single line diagram of main board, distribution board, and motor
control panel for controlling of two 3-ph motors..
[Link] a single line diagram of OH distribution line for a model colony.
[Link] of detailed list of materials and accessories (schedule) of pole
mounted transformer.
[Link] of lighting scheme and Estimation of wiring for classroom.
18. List the material required for Pipe earthing.
[Link] a neon sign to display ELECTRICAL
[Link] the testing methods of a new electrical installation.

SECTION-III (Identification/ Spotting)

Note: (i) Answer any Five Questions.
(ii) Each Question carries 2 marks 5X2=10 Marks

[Link] the wiring accessories and materials in wiring of your

examination hall or laboratory.
[Link] the given Main Board and Distribution Board and draw the
connections.
[Link] the format of estimate?
[Link] is the purpose of earthing?
[Link] the single line diagram of motor installation.
[Link] MCB, MCCB, MCP, MB.

30
[Link] the types of OH lines.
[Link] P A system layout name important equipment.
[Link] different lighting methods in auditorium.
[Link] the parts of a Refrigerator.

SECTION-IV
Record 5 marks
Viva- Voice 5 Marks

31
 ELECTRICAL TECHNICIAN
SECOND YEAR
MODEL QUESTION PAPER

Paper III: Electrical Estimation and Utilization Lab

Time: 3hrs Max. Marks: 50

SECTION-I (Major Experiment)
Note: (i) Answer any one Question.
(ii) Each Question carries 20 mark 1X20=20 Marks

1. Take the measurements of residential building and prepare wiring layout.

2. Take the measurements of shop and prepare the wiring layout.
3. Take the measurements of college block and prepare wiring layout.
4. Prepare the detailed estimate in standard format for installing surface
conduit wiring in a small residential building.
5. Prepare the detailed estimate in standard format for installing casing

and capping wiring in a small shop.

SECTION-II (Minor Experiment)

Note: (i) Answer any One Question
(ii) Each Question carries 10 marks 1X10=10 Marks

[Link] connections of 1-ph service mains, main board (load 1000W)

[Link] connections of 3-ph main board and distribution board (load
4500W)
[Link] a motor control panel for controlling of 1-ph motors.
[Link] the single line diagram of main board, distribution board, and motor
control panel for controlling of two 3-ph motors..
[Link] a single line diagram of OH distribution line for a model colony.

32
 SECTION-III (Identification/ Spotting)
Note: (i) Answer any Five Questions.
(ii) Each Question carries 2 marks 5X2=10 Marks

[Link] MCB, MCCB, MCP, MB.

[Link] the types of OH lines.
[Link] P A system layout name important equipment.
[Link] different lighting methods in auditorium.
[Link] the parts of a Refrigerator.

SECTION-IV
Record 5 marks
Viva- Voice 5 Marks

Note: The serial numbers of the questions mentioned above are the serial number in
question bank. In practical examination only the serial number of the question will be
given. The examiner shall decode it with the question bank and give the questions.

33
 ELECTRICAL TECHNICIAN
SECOND YEAR
SCHEME OF VALUATION

Paper III: Electrical Estimation and Utilization Lab

Time: 3hrs Max. Marks: 50

Section – I (Major Experiment) 1X 20 = 20 Marks
Aim, Tools, Materials :5 marks
Circuit Diagram :5 marks
Experiment :5 marks
Presentation and Result :5 marks
Section – II (Minor Experiment) 1X 10 = 10 Marks

Diagram/circuit : 5 marks;

Order of performing experiment/explanation : 5 marks

Section – III (Identification / Spotting) 5X 2 = 10 Marks

Select any FIVE practical from Q no 21 to 30

SECTION-IV
Record 5 marks
Viva- Voice 5 Marks

34