PUMP CALCULATION PART 1

SYSTEM CHARACTERISTICS
SINGLE STAGE CENTRIFUGAL PUMP CALCULATION Version 1.001 Nov-97 Q Ptot Ltot Ftot Htot
(Clean Water Use) 215 0.00 -0.008 54.13 54.12
Static Suction Lift = Ls Pump Suction Diam = Ds SYSTEM CURVE
Static Discharge Head = Ld Pump Discharge Diam = Dd 250.00 0 0.00 -0.008 0 -0.01
Total Static Head Ltot = Ls + Ld 26.875 0.00 -0.008 0.84576 0.84
Friction Head = Hfs and Hfd 53.75 0.00 -0.008 3.38303 3.38
Inlet and Discharge Nozzle Losses = Hi and Ho 200.00 80.625 0.00 -0.008 7.61181 7.60
Velocity Head = V2/2g [often included in pump curves] 107.5 0.00 -0.008 13.5321 13.52
Pump Suction and Discharge Nozzle Elevations = Lns and Lnd 134.375 0.00 -0.008 21.1439 21.14
Suction Pressure Head = Ps [if open tank = 0] 150.00 161.25 0.00 -0.008 30.4472 30.44

METRES HEAD
Discharge Pressure Head = Pd [if open tank = 0] 188.125 0.00 -0.008 41.4421 41.43
215 0.00 -0.008 54.1284 54.12
100.00 241.875 0.00 -0.008 68.5063 68.50
268.75 0.00 -0.008 84.5757 84.57
295.625 0.00 -0.008 102.337 102.33
50.00 322.5 0.00 -0.008 121.789 121.78
Pout = Pd + Ld + Hfd + Ho - Lnd = Hd - Vd2/2g - Lnd 349.375 0.00 -0.008 142.933 142.92
376.25 0.00 -0.008 165.768 165.76
0.00 403.125 0.00 -0.008 190.295 190.29
Pin = Ps - Ls - Hfs - Hi + Lns = - Hs - Vs2/2g + Lns 0 50 100 150 200 250 300 350 400 450 500 430 0.00 -0.008 216.514 216.51

L/sec 215 55.53

Total Dynamic Suction Lift Hs = Ls - Ps + Hfs + Hi - Vs2/2g Dynamic Suction Lift (req'd) Hs(r) = Ls - Ps + Hfs + Hi WATER VAPOUR PRESSURE
Total Dynamic Discharge Head Hd = Ld + Pd + Hfd + Ho + Vd2/2g Dynamic Discharge Head (req'd) Hd(r) = Ld + Pd + Hfd + Ho degC kPa(abs)
Total Dynamic Head Htot = Hd + Hs Dynamic Head (req'd) Htot(r) = Hd(r) + Hs(r) 0 0.6
NPSHa(req'd) NPSHa(r) = NPSHa - Vs2/2g 15 1.7
Closed Tank: NPSHa(abs) = Ps + Patm - Ls - Hfs - Hi + Vs2/2g - Pvap [where Pvap = Vapour Pressure(abs)] Provide this to pump vendor and use on pump curves 25 3.2
Open Tank: or = Pamb - Ls - Hfs - Hi + Vs2/2g - Pvap [NPSHa should exceed NPSHr by at least 0.5 m] where velocity head is included in vendors pump curves. 30 4.25
40 7.38
SYSTEM PROPERTIES SYSTEM CHARACTERISTICS PUMP SELECTION (Nominal) 50 12.5
Q 215 l/sec 0.2150 m3/sec Patm 10.329 m 101.325 kPa(abs)
SG 1 D 1000 kg/m3 Pamb 9.980 m 97.900 kPa(abs) Pump Speed 1483 rpm 120 198.5
Tfluid 16 oC Vs 0.978 m 4.38 m/sec 140 361.4
Pvap 0.19 m(abs) 1.9 kPa(abs) Pinlet -2.669 m -26.180 kPa(g) Impeller Diam 0.449 m
Ps 0.00 m 0 kPa(g) Hs 1.991 m 19.531 kPa Pump Head 61.95 m
Ls 0.930 m 9.1 kPa Hs(r) 2.969 m 29.123 kPa
Hi 0.000 m 0 kPa Vd 2.387 m 6.84 m/sec Hydraulic Power 117.12 kW NOTES:
Hfs 2.039 m 20 kPa Poutlet 51.452 m 504.741 kPa(g) Pump Efficiency 83.8% For Hfs and Hfd try 50 kPa/100m
Ds 0.250 m As 0.0491 m2 Hd 53.539 m 525.216 kPa Motor Power 139.76 kW
Lns 0.3 m 2.943 kPa Hd(r) 51.152 m 501.798 kPa Select Ds and Dd for Vs and Vd around 3 m/sec
Pd 0.00 m 0 kPa(g) Specific Speed 1069
Ld -0.938 m -9.20178 kPa Htot 55.53 m 544.75 kPa For small pumps try 60% efficiency
Ho 0.000 m 0 kPa Htot(r) 54.12 m 530.92 kPa NPSHr 2 m
Hfd 52.090 m 511 kPa Normally approx. 3% Htot = 1.666 m
Dd 0.200 m Ad 0.0314 m2 NPSHa 7.79 m(abs) 76.47 kPa(g)
Lnd -0.3 m -2.943 kPa NPSHa(r) 6.82 m(abs) 66.88 kPa(g)

828739101.xlsx CENTRIFUGAL 12/17/2024