PROFESSIONAL FOUR-CHANNEL AUDIO

MIXER WITH USB AND DSP PROCESSOR

CONTENTS
Warning..........................................................................................................................1-2

Precautions............….................................................................................................…....3

Package Contents ……..………................................................................................….....… 4

Features.................................................................................................................. ........ 4

Functions and Controls……................................................................................…..……...4-7

Specifications.......................….......................................................................................... 7

Troubleshooting……………….................................................................................……........8

Service Information…….……...................................................................................………...9

1 2
On Safety

* Operate only on designated AC power supply (120V AC in North America).

* Should any liquid or solid object fall into the cabinet, unplug the unit and have it checked by

qualified personnel before operating it any further.

* Unplug the unit from the wall outlet or set the Master switch to OFF if it is not to be used for

several days.

* To disconnect the cord, pull it out by the plug. Never pull the cord itself.

On Installation

* Allow adequate air circulation to prevent internal heat build-up. Do not place the unit on

surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the

ventilation holes.

* Do not install the unit in a location near heat sources such as radiators or air ducts, or in a place

subject to direct sunlight, excessive dust, mechanical vibration or shock. 1. [MIC] Input Jack --- This is a balanced XLR microphone input jack.
This XLR input jack is to be connected to a microphone through
a balanced microphone cable with a male XLR plug.
1 2. [LINE] Input Jack --- This is an unbalanced 1/4” input jack. This 1/4”
On Repackaging input jack is to be connected to a microphone, a musical
instrument, or an audio device (such as CD player) through an
2 unbalanced cable with a 1/4” TS plug.
3 3. [INSERT] Jack --- This is a 1/4” TRS phone jack allowing you to
Do not throw away the carton and packing materials. They make an ideal container in which to insert external line devices (such as gating, compressing,
equalizing, and /or reverb effects) into the signal path. This
transport the unit. When shipping the unit to another location, repack it as it was originally insert jack is configured with “TIP” send and “RING” return.
packed at the factory. 4 4. [GAIN] Control Knob --- This knob is used to raise or lower the gain
5 level of the input signal. When the audio level is higher than a
predetermined threshold, the [PEAK] LED indicator (refer to
6 numeral 11) will keep blinking until the audio level goes below
the threshold.
5. [PAN] Control --- This control determines how much of the input
signal is sent to the left and right channels. When the knob is
centered at 12 O’clock, the input signal is sent equally to the
left channel and the right channel with a -3dB attenuation.
Turn this control fully counter-clockwise to send 100% of the
input signal to the left channel. Turn this control fully clockwise
to send 100% of the input signal to the right channel.
6. [HIGH] Treble-tone Control Knob --- This knob is used to adjust
the gain for the input signal band centered at 12.5KHz in the
range from -15dB to +15dB.

3 4
 7. [MID] Alto-tone Control Knob --- This knob is used to adjust the 1. [+48V PHANTOM] Button/LED --- When one or more condenser
microphones are connected to the XLR [MIC] input jacks
gain for the input signal band centered at 2.5KHz in the range (refer to numeral 1 in the CHANNEL INPUT section), press
from -15dB to +15dB. 1 2 this [+48V PHANTOM] button to turn on the 48V phantom
8. [LOW] Bass-tone Control Knob --- This knob is used to adjust the power to the condenser microphones via the XLR [MIC] input
jacks. When the 48V phantom power is turned on, the phantom
gain for the input signal band centered at 80Hz in the range power LED light will be turned on.
from -15dB to +15dB. 2. Stereo Signal Level Meter --- This is a stereo signal level meter
9. [AUX] Control --- This control adjusts the level of the input sent to configured with three green LED lights at the bottom, one
the AUX output (refer to numeral 4 in section MAIN TERMINALS yellow LED light at the middle, and one red LED light at the
top on both the left channel side and the right channel side.
on page 6). 4 When the red LED light is turned on frequently, the [MAIN OUT]
10. [EFF] Control --- This control is used to adjust the level of the signal 3 output signal level may need to be lowered by adjusting the
routed from this channel to the reverberation line. This signal [MAIN] level fader (refer to numeral 8.
5 3. [DELAY] Control --- This control adjusts the depth of the reverberation.
level will vary according to the settings of the channel attenuators 4. [REP] Repeat Control --- This control adjusts the repetition times
(HIGH, MID,LOW). The signals from the stereo channel (R and L) of the reverberation.
7 will be mixed before being routed to the reverberation line. 6 5. [PHONES ] Level Control --- This control adjusts the earphone
volume.
11. [PEAK] LED Indicator --- This PEAK LED indicator will keep blinking
6. [AUX] Level Control --- This control adjusts the signal level from
8 when the input signal level is higher than a predetermined 7 the [AUX] output jack (refer to numeral 4 in Section MAIN
threshold. When the PEAK LED indicator is blinking, adjust the 8 TERMINALS on page 6).
9 gain control knob (refer to numeral 4) to a lower gain level until 7. [FX LEVEL] Control --- This effects return level control adjusts the
volume of the reverberation effect.
the PEAK LED indicator stops blinking to maintain the sound 8. [MAIN] Level Fader --- This level fader is used to adjust the [MAIN]
10 quality. output (refer to numeral 2 in Section MAIN TERMINALS) signal
12. [LEVEL] Control Fader --- This level control fader is used to raise or volume.
11
12 lower the audio volume of the signal from this channel.

1 1. [PHONES] Stereo Output Jack --- This is a 1/4” TRS jack for the
stereo monitoring earphones.
1. USB interface --- The volume and sound quality of the audio signal 2. [MAIN] Stereo Output Jacks --- These are stereo main output 1/4”
from the USB interface can be controlled by the control knobs TS jacks. These jacks are to be connected to power amplifiers
of the [CH3/4] channel. or active speakers.
2. [REC] Stereo Output Jacks --- These are the REC stereo RCA output 3. [FX/INS] Jack --- This is a 1/4” TRS phone jack allowing you to insert
1 jacks. These jacks are for recording output signal. The recording external line devices (such as gating, compressing, equalizing,
output signal level is controlled by the MAIN level fader(refer
2 and /or reverb effects) into the signal path. This insert jack is
to numeral 8 in the MAIN CONTROL section on page 6) . configured with “TIP” send and “RING” return.
3. [TAPE/CD IN] Stereo Input Jacks --- These are the Tape/CD stereo 4. [AUX] Output Jack --- This AUX output is a ¼” TS jack. This AUX
2 RCA input jacks. The volume and sound quality of the audio output is the sum of the signals sent from each channel. If a
signal from these RCA input jacks are controlled by the control particular channel’s AUX control knob (refer to numeral 9 in
3
3 4 section CHANNEL INPUT on page 5) is fully turned down, that
knobs of the [CH3/4] channel.
channel is not contributing to the AUX output signal.
5 4. [3/4][USB] Selection Button --- Press down this button to have the
level of the stereo channel [CH 3/4] signal controlled by the CH3/4
controls. When this button is depressed, press this button again
to raise the button to have the level of the USB input signal
4 controlled by the CH3/4 controls.
5. [3/4] Stereo Input Jacks --- These are the ¼” TS input jacks for
channel 3 and channel 4. Channel 3 is utilized as the left channel
while channel 4 is utilized as the right channel in the stereo mode.
If only one 1/4” TS plug is connected to channel 3 and the channel 4
input jack is not connected, the mono audio signal to channel 3
1 2
will be routed to channel 4 simultaneously, such that both channel 3
and channel 4 carry the same mono audio signal.

5 6
 A. USB Insert
B. USB LED Indicator
C. “ ” Play/Pause Button --- Press this button to start playing the
music from the USB device. Press this button again to have the
music paused. When the music is paused, press this button will
continue the music from where it was paused.
D. “ ” Prev Button --- Press this button to skip the current track
A B C D E and jump back to the previous track.
E. “ ” Next Button --- Press this button to skip the current track
and jump to the next track.

SOURCE 100-240VAC

11W

7 8
9