NATIONAL AEROSPACE STANDARD

© COPYRIGHT 2015 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC. ALL RIGHTS RESERVED

FED. SUPPLY CLASS

30°+0°-15° 5305
F 30°APPROX
H L
.02 APPROX
R
AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC

/6/
B /4/ /5/
ØD OPTIONAL DESIGN
2
TABLE I
NOMINAL SIZE .2500 .3125 .3750 .4375 .5000 .5625 .6250 .7500 .8750 1.0000 1.1250 1.2500
ARLINGTON, VA 22209
1000 WILSON BLVD.

B THREADS UNF-2A /4/ /5/ 28 24 24 20 20 18 18 16 14 12 12 12

MAX .2500 .3125 .3750 .4375 .5000 .5625 .6250 .7500 .8750 1.0000 1.1250 1.2500
ØD BODY
MIN .2450 .3065 .3690 .4305 .4930 .5545 .6170 .7410 .8660 .9900 1.1140 1.2390
F WIDTH MAX .4375 .5000 .5625 .6250 .7500 .8125 .9375 1.1250 1.3125 1.5000 1.6875 1.8750
ACROSS FLATS MIN .4280 .4890 .5510 .6120 .7360 .7980 .9220 1.1000 1.2850 1.4690 1.6310 1.8120
G WIDTH MAX .505 .577 .650 .722 .866 .938 1.083 1.299 1.516 1.732 1.949 2.165
ACROSS CORNERS MIN .488 .557 .628 .698 .840 .910 1.051 1.254 1.465 1.675 1.859 2.066
MAX .163 .211 .243 .291 .323 .371 .403 .483 .563 .627 .718 .813
H HEAD HEIGHT
MIN .150 .195 .226 .272 .302 .348 .378 .455 .531 .591 .658 .749
MAX .025 .025 .025 .025 .025 .045 .045 .045 .065 .095 .095 .095
R RADIUS
MIN .015 .015 .015 .015 .015 .020 .020 .020 .040 .060 .060 .060
MIN TENSILE STRENGTH LBS /9/ 2,910 4,640 7,020 9,500 12,800 16,200 20,450 26,100 35,600 46,400 59,900 75,000
TOLERANCE
L DASH DASH DASH DASH DASH DASH DASH DASH DASH DASH DASH DASH
SIZE 3/4 SIZE 7/8
LENGTH NO. NO. NO. NO. NO. NO. NO. NO. NO. NO. NO. NO.
AND UNDER AND OVER
.375 301 327 353
.438 302 328 354 379

REVISION DATE: MARCH 31, 2015

.500 303 329 355 380 404
.562 +.000 +.000 304 330 356 381 405 430
.625 -.031 -.062 305 331 357 382 406 431 455
.750 306 332 358 383 407 432 456 479
.875 307 333 359 384 408 433 457 480 502
PRODUCT AND SHALL BECOME EFFECTIVE NO LATER THAN SIX MONTHS FROM THE LAST
THIS DRAWING SUPERSEDES ALL ANTECEDENT STANDARD DRAWINGS FOR THE SAME

1.000 308 334 360 385 409 434 458 481 503 524
1.125 309 335 361 386 410 435 459 482 504 525 545
1.250 310 336 362 387 411 436 460 483 505 526 546 565
1.375 +.000 +.000 311 337 363 388 412 437 461 484 506 527 547 566
1.500 -.062 -.125 312 338 364 389 413 438 462 485 507 528 548 567
1.750 313 339 365 390 414 439 463 486 508 529 549 568
2.000 314 340 366 391 415 440 464 487 509 530 550 569
2.250 315 341 367 392 416 441 465 488 510 531 551 570
2.500 316 342 368 393 417 442 466 489 511 532 552 571
2.750 317 343 369 394 418 443 467 490 512 533 553 572
3.000 318 344 370 395 419 444 468 491 513 534 554 573
3.250 319 345 371 396 420 445 469 492 514 535 555 574
3.500 320 346 372 397 421 446 470 493 515 536 556 575
3.750 +.000 +.000 321 347 373 398 422 447 471 494 516 537 557 576
4.000 -.094 -.188 322 348 374 399 423 448 472 495 517 538 558 577 ISSUE DATE: OCTOBER 1998
4.250 323 349 375 400 424 449 473 496 518 539 559 578
4.500 324 350 376 401 425 450 474 497 519 540 560 579
4.750 325 351 377 402 426 451 475 498 520 541 561 580
5.000 326 352 378 403 427 452 476 499 521 542 562 581
5.500 428 453 477 500 522 543 563 582
REVISION DATE.

6.000 429 454 478 501 523 544 564 583

THE INITIAL RELEASE OF THIS DOCUMENT SUPERSEDES MS35308, REVISION E, AMENDMENT 1. PART NUMBERS REMAIN MS35308.
THIRD CUSTODIAN REVISION
ANGLE
PROJECTION NATIONAL AEROSPACE STANDARDS COMMITTEE 2
PROCUREMENT TITLE CLASSIFICATION
FORM 12-01

SPECIFICATION PART STANDARD

SCREW, CAP, HEXAGON HEAD (FINISHED HEXAGON BOLT),
FF-S-85 STEEL, CORROSION RESISTING, PASSIVATED, UNF-2A NASM35308
SHEET 1 OF 3
--`,````,``,```,`,`````,,,```,-`-`,,`,,`,`,,`---
USE OF OR RELIANCE UPON THIS DOCUMENT OR ANY NATIONAL AEROSPACE STANDARD IS ENTIRELY VOLUNTARY. AIA DOES NOT QUALIFY SUPPLIERS OR CERTIFY
Copyright Aerospace Industries Association of America Inc.
CONFORMANCE OF ITEMS PRODUCED UNDER NATIONAL AEROSPACE STANDARDS. AIA MAKES NO REPRESENTATION OR CLAIM RESPECTING (1) THE SUITABILITY OF
Provided by IHS Markit under license with AIA/NAS Licensee=Israel Aerospace Industries Ltd - Lod, Israel/5943181001, User=RAM, MEI
ITEMS without
No reproduction or networking permitted FOR ANY PARTICULAR
license from IHS APPLICATION OR (2) THE EXISTENCE OF OR APPLICABILITY THERETO
Not for Resale, OF PATENT
09/08/2019 OR TRADEMARKS RIGHTS.
07:37:36 MDT
 NATIONAL AEROSPACE STANDARD
© COPYRIGHT 2015 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC. ALL RIGHTS RESERVED

MATERIAL:

CORROSION-RESISTING STEEL, 300 SERIES, IN ACCORDANCE WITH PROCUREMENT SPECIFICATION.

AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC

2 FINISH: PASSIVATED IN ACCORDANCE WITH AMS2700, METHOD 1, CLASS 4.

BLACK OXIDE COAT IN ACCORDANCE WITH MIL-DTL-13924, CLASS 4.

2 CODE: THE MS PART NUMBER CONSISTS OF THE MS NUMBER PLUS THE DASH NUMBER. ADD “B” CODE AFTER DASH
NUMBER FOR BLACK OXIDE COATING.

EXAMPLE OF PART NUMBER:

MS35308-301 = INDICATES SCREW, CAP, HEXAGON HEAD, 300 SERIES CORROSION-RESISTANT STEEL,
ARLINGTON, VA 22209

PASSIVATED; .2500-20 UNF-2A NOMINAL THREAD SIZE, .375 LENGTH.

1000 WILSON BLVD.

--`,````,``,```,`,`````,,,```,-`-`,,`,,`,`,,`---
2 MS35308-301B = INDICATES SCREW, CAP, HEXAGON HEAD, 300 SERIES CORROSION-RESISTANT STEEL,
PASSIVATED; .2500-20 UNF-2A NOMINAL THREAD SIZE, .375 LENGTH, BLACK OXIDE
COATED.

NOTES:

(1) REMOVE ALL BURRS AND SHARP EDGES.

(2) THIS STANDARD TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN.

2 (3) MAGNETIC PERMEABILITY SHALL BE LESS THAN 2.0 (Air = 1.0) FOR A FIELD STRENGTH H = 200 OERSTEDS
USING A MAGNETIC PERMEABILITY INDICATOR PER ASTM A342/A342M, TEST METHOD 3. NOTE: COLD
WORKED SCREWS MAY NOT BE CAPABLE OF MEETING PERMEABILITY AND STRENGTH REQUIREMENTS
SIMULTANEOUSLY.

/4/ THE THREADS SHALL BE IN ACCORDANCE WITH FED-STD-H28/2. ACCEPTABILITY OF SCREW THREADS SHALL
BE IN ACCORDANCE WITH FED-STD-H28/20, SYSTEM 21.
PRODUCT AND SHALL BECOME EFFECTIVE NO LATER THAN SIX MONTHS FROM THE LAST
THIS DRAWING SUPERSEDES ALL ANTECEDENT STANDARD DRAWINGS FOR THE SAME

/5/ THREAD LENGTH: MINIMUM THREAD LENGTH SHALL BE TWICE THE DIAMETER PLUS .250 INCH. THE
TOLERANCE SHALL BE PLUS .188 INCH OR 2.5 THREADS, WHICHEVER IS GREATER. ON SCREWS THAT ARE TOO
SHORT FOR MINIMUM THREAD LENGTHS, THE DISTANCE FROM THE BEARING SURFACE OF THE HEAD TO THE
FIRST COMPLETE THREAD SHALL NOT EXCEED THE LENGTH OF 2.5 THREADS FOR SIZES UP TO AND INCLUDING
1.000 INCH AND 3.5 THREADS FOR SIZES LARGER THAN 1.000 INCH.

/6/ HEAD MARKING: HEADS SHALL BE MARKED IN ACCORDANCE WITH MIL-HDBK-131. RAISED MARKINGS ARE
PREFERRED, STAMPINGS ARE ACCEPTABLE.

(7) DIMENSIONS ARE IN INCHES.

(8) UNLESS OTHERWISE SPECIFIED, PART INVENTORY MANUFACTURED TO PREVIOUS REVISIONS OF THE
APPLICABLE DRAWING OR SPECIFICATION MAY BE PROCURED AND USED UNTIL STOCK IS DEPLETED.

/9/ BASED ON MINIMUM ULTIMATE TENSILE STRENGTH OF 80,000 P.S.I. FOR DIAMETERS THRU 5/8 INCH, AND
70,000 P.S.I. FOR DIAMETERS OVER 5/8 INCH. BREAKING STRENGTHS ARE CALCULATED BY THE STRESS AREAS
INDICATED IN FED-STD-H28.
REVISION DATE.

2 (10) UNLESS OTHERWISE SPECIFIED HEREIN, REFERENCED DOCUMENTS SHALL BE THE ISSUE IN EFFECT ON DATE
OF MANUFACTURE. HOWEVER, EXISTING MATERIAL INVENTORY CERTIFIED TO A PREVIOUS REVISION OF THE
APPLICABLE MATERIAL SPECIFICATION(S) IS ACCEPTABLE FOR USE UNTIL DEPLETION.

REVISION

2
FORM 12-01

NASM35308
SHEET 2
USE OF OR RELIANCE UPON THIS DOCUMENT OR ANY NATIONAL AEROSPACE STANDARD IS ENTIRELY VOLUNTARY. AIA DOES NOT QUALIFY SUPPLIERS OR CERTIFY
Copyright Aerospace Industries Association of America Inc.
CONFORMANCE OF ITEMS PRODUCED UNDER NATIONAL AEROSPACE STANDARDS. AIA MAKES NO REPRESENTATION OR CLAIM RESPECTING (1) THE SUITABILITY OF
Provided by IHS Markit under license with AIA/NAS Licensee=Israel Aerospace Industries Ltd - Lod, Israel/5943181001, User=RAM, MEI
ITEMS without
No reproduction or networking permitted FOR ANY PARTICULAR
license from IHS APPLICATION OR (2) THE EXISTENCE OF OR APPLICABILITY THERETO
Not for Resale, OF PATENT
09/08/2019 OR TRADEMARKS RIGHTS.
07:37:36 MDT
 NATIONAL AEROSPACE STANDARD
© COPYRIGHT 2015 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC. ALL RIGHTS RESERVED

THE SCREWS COVERED BY DASH NUMBERS GIVEN IN ORIGINAL ISSUE OF THIS STANDARD ARE CANCELED AFTER
10 MAY 1963. USE THE DASH NUMBERS GIVEN IN THE PRECEDING SHEETS OF THIS STANDARD. THE CANCELED
SCREWS CANNOT ALWAYS REPLACE THE NEW SCREWS AND SHOULD BE USED UNTIL EXISTING STOCKS ARE
DEPLETED. USE ONLY THE NEW SCREWS FOR DESIGN AND REPLACEMENT. REPLACEMENT SHOULD BE IN
AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC

ACCORDANCE WITH THE FOLLOWING TABLE.

TABLE II – INTERCHANGEABILITY
DASH NUMBERS DASH NUMBERS DASH NUMBERS DASH NUMBERS DASH NUMBERS
CANCELED NEW CANCELED NEW CANCELED NEW CANCELED NEW CANCELED NEW
MS35308 MS35308 MS35308 MS35308 MS35308 MS35308 MS35308 MS35308 MS35308 MS35308
1 301 58 358 115 415 172 472 229 529
2 302 59 359 116 416 173 473 230 530
3 303 60 360 117 417 174 474 231 531
4 304 61 361 118 418 175 475 232 532
ARLINGTON, VA 22209

5 305 62 362 119 419 176 476 233 533

1000 WILSON BLVD.

6 306 63 363 120 420 177 477 234 534

7 307 64 364 121 421 178 478 235 535
8 308 65 365 122 422 179 479 236 536
9 309 66 366 123 423 180 480 237 537
10 310 67 367 124 424 181 481 238 538
11 311 68 368 125 425 182 482 239 539
12 312 69 369 126 426 183 483 240 540
13 313 70 370 127 427 184 484 241 541
14 314 71 371 128 428 185 485 242 542
15 315 72 372 129 429 186 486 243 543
16 316 73 373 130 430 187 487 244 544
17 317 74 374 131 431 188 488 245 545
18 318 75 375 132 432 189 489 246 546
19 319 76 376 133 433 190 490 247 547
20 320 77 377 134 434 191 491 248 548
21 321 78 378 135 435 192 492 249 549
22 322 79 379 136 436 193 493 250 550
23 323 80 380 137 437 194 494 251 551
24 324 81 381 138 438 195 495 252 552
25 325 82 382 139 439 196 496 253 553
26 326 83 383 140 440 197 497 254 554
27 327 84 384 141 441 198 498 255 555
28 328 85 385 142 442 199 499 256 556
29 329 86 386 143 443 200 500 257 557
PRODUCT AND SHALL BECOME EFFECTIVE NO LATER THAN SIX MONTHS FROM THE LAST

30 330 87 387 144 444 201 501 258 558

THIS DRAWING SUPERSEDES ALL ANTECEDENT STANDARD DRAWINGS FOR THE SAME

--`,````,``,```,`,`````,,,```,-`-`,,`,,`,`,,`---
31 331 88 388 145 445 202 502 259 559
32 332 89 389 146 446 203 503 260 560
33 333 90 390 147 447 204 504 261 561
34 334 91 391 148 448 205 505 262 562
35 335 92 392 149 449 206 506 263 563
36 336 93 393 150 450 207 507 264 564
37 337 94 394 151 451 208 508 265 565
38 338 95 395 152 452 209 509 266 566
39 339 96 396 153 453 210 510 267 567
40 340 97 397 154 454 211 511 268 568
41 341 98 398 155 455 212 512 269 569
42 342 99 399 156 456 213 513 270 570
43 343 100 400 157 457 214 514 271 571
44 344 101 401 158 458 215 515 272 572
45 345 102 402 159 459 216 516 273 573
46 346 103 403 160 460 217 517 274 574
47 347 104 404 161 461 218 518 275 575
48 348 105 405 162 462 219 519 276 576
49 349 106 406 163 463 220 520 277 577
50 350 107 407 164 464 221 521 278 578
51 351 108 408 165 465 222 522 279 579
52 352 109 409 166 466 223 523 280 580
REVISION DATE.

53 353 110 410 167 467 224 524 281 581

54 354 111 411 168 468 225 525 282 582
55 355 112 412 169 469 226 526 283 583
56 356 113 413 170 470 227 527
57 357 114 414 171 471 228 528

REVISION

2
FORM 12-01

NASM35308
SHEET 3
USE OF OR RELIANCE UPON THIS DOCUMENT OR ANY NATIONAL AEROSPACE STANDARD IS ENTIRELY VOLUNTARY. AIA DOES NOT QUALIFY SUPPLIERS OR CERTIFY
Copyright Aerospace Industries Association of America Inc.
CONFORMANCE OF ITEMS PRODUCED UNDER NATIONAL AEROSPACE STANDARDS. AIA MAKES NO REPRESENTATION OR CLAIM RESPECTING (1) THE SUITABILITY OF
Provided by IHS Markit under license with AIA/NAS Licensee=Israel Aerospace Industries Ltd - Lod, Israel/5943181001, User=RAM, MEI
ITEMS without
No reproduction or networking permitted FOR ANY PARTICULAR
license from IHS APPLICATION OR (2) THE EXISTENCE OF OR APPLICABILITY THERETO
Not for Resale, OF PATENT
09/08/2019 OR TRADEMARKS RIGHTS.
07:37:36 MDT