© Bosch Rexroth Corp.

, RE98756/2021-08-24

eOC BODAS Pump Control

Software for Electronic Open Circuit Pumps

The portfolio of open circuit axial piston units from Bosch Rexroth
provides a high variance of hydro-mechanical control functions
with mechanical interfaces for machine optimization. With the
electronification of axial piston units all these hydro-mechanical
control functions and interfaces are now transferred into software
thus enabling customizable control modes and adjustable pump
dynamics during operation. eOC BODAS pump control from
Bosch Rexroth is suitable for a wide range of mobile working
machines with open hydraulic circuit – from construction,
agricultural and forestry machines to municipal vehicles.

CUSTOMER BENEFITS FUNCTION AND BENEFITS

▪ Electrohydraulic pump control Electrohydraulic pump control
▪ Adjustable and variable pump dynamics The eOC BODAS pump control software comprises three control
▪ Improved machine performance and productivity modes in an electronic closed loop control logic:
▪ Less fuel consumption and optimized battery usage ▪ Pressure or delta pressure control
▪ Reduced pump variance and service effort ▪ Flow and angle control
▪ Torque control
All control modes come with a predefined set of parameters to
achieve an optimized performance of the installed Rexroth eOC
pump in the hydraulic system (e.g. Load Sensing). The control
APPLICATIONS software runs on a dedicated Bosch Rexroth control unit “SRC
eOC”, which provides the resulting control current to the
electrohydraulic pump interface.

Adjustable and variable pump dynamics

With the ENTRY version of the eOC BODAS pump control
software, the set values and parameters for each control mode
can be pre-configured with fixed values via BODAS Service. The
PREMIUM variant allows to dynamically adjust the set points via
CAN-Bus interface, which opens up a huge range of additional
functionalities and leads to a customizable machine performance.
eOC BODAS Pump Control
Software for Electronic Open Circuit Pumps

TECHNICAL DATA
eOC BODAS Pump Control Improved machine performance and productivity
Mobile working machines are highly productive and optimized for
Engine Type: Mechanic / CAN SAE J1939 Diesel their intended load cycles. At the same time, the installed engine
or Electrical Machine power is limited. With the new eOC BODAS pump control
Rexroth Pumps: A10VO, A11VO, A15VO software from Bosch Rexroth it is now possible to establish a
prepared for eOC pump control direct communication between engine and axial piston pump to
continuously and dynamically adapt the hydraulic power to the
Powerless Condition: Pump at minimum displacement;
available engine torque. Further, the pump software is able to
inverse logic on demand
compensate disturbances (e.g. temperature, speed) in machine
Rexroth Sensors: Angle Sensor load cycles, which allows highly dynamic operating functions with
Pressure Sensor Pump (PR4 SENT) a very high level of precision to increase the overall productivity of
Opt.: Pressure Sensor LS (PR4 the mobile working machine.
SENT)
Operator interface: Discret or CAN SAE J1939 Less fuel consumption and optimized battery usage
The control principle of an axial piston pump and how it interacts
Rexroth Control Unit: SRC eOC
with the hydraulic system are two of the major aspects that affect
Safety standards: Ready for EN ISO 13849 the energy efficiency of a mobile working machine. eOC BODAS
pump control targets to optimize both. On the one hand, the
Variants: ENTRY and PREMIUM
consolidation of multiple controller axes for pressure, flow and
Diagnostic interface: BODAS-service and CAN SAE J1939 torque into one results in a reduced fluid consumption of the
Data sheet: 95345 pump controller itself. On the other hand, the possibility to
dynamically adjust control parameters, for instance in standby
condition or during eco mode, allows to minimize the energy
CAN J1939
consumption of the overall hydraulic system.

SRC eOC Reduced pump variance and service effort

Customer
As all the different controller types and mechanical settings of
ECU
Bosch Rexroth axial piston units can be transferred into software,
Pump Load the number of pump configurations required for an OEM can be
Pressure Pressure significantly reduced. This directly affects the effort of managing
spare parts and aftermarket components and at the same time
Engine Swivel
ECU simplifies engineering work. In the event of a malfunction or
angle
feature update the eOC BODAS pump control software can be
maintained via the BODAS service interface. Further, BODAS
service provides a detailed guideline for efficient commissioning
of the mobile working machine.

eOC Pump

Electronic Open Circuit eOC

Bosch Rexroth Corporation © Bosch Rexroth AG 2021. All rights reserved, also regarding any disposal,
Corporate Headquarters exploitation, reproduction, editing, distribution, as well as in the event of applications
14001 South Lakes Drive for industrial property rights.

Charlotte, NC 28273
The data specified within only serves to describe the product. No statements
Phone (800) REXROTH
concerning a certain condition or suitability for a certain application can be derived
(800)
800) 739-7684
from our information. The information given does not release the user from the
[email protected] obligation of own judgment and verification. It must be remembered that our products
www.boschrexroth-us.com are subject to a natural process of wear and aging.