Scribd
Upload
94 views1 page

Technical Data ASTM A500 & A500M

The document provides technical data for ERW Carbon Steel Tubes in round, square, and rectangular shapes conforming to ASTM A500/A500M, including size ranges, tolerances, chemical composition, and mechanical properties. It specifies dimensions, wall thickness, straightness, and various grades with their respective yield and tensile strengths. Additionally, it outlines workmanship standards and marking requirements for the products.

Uploaded by

aswinkovilakam
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
94 views1 page

Technical Data ASTM A500 & A500M

The document provides technical data for ERW Carbon Steel Tubes in round, square, and rectangular shapes conforming to ASTM A500/A500M, including size ranges, tolerances, chemical composition, and mechanical properties. It specifies dimensions, wall thickness, straightness, and various grades with their respective yield and tensile strengths. Additionally, it outlines workmanship standards and marking requirements for the products.

Uploaded by

aswinkovilakam
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd

TECHNICAL DATA OF STRUCTURAL TUBING IN ROUND & SHAPES CONFORMING TO ASTM A500/A500M

SCOPE : ERW Carbon Steel Tubes in Round, Square and Rectangular shapes.
SIZE RANGE : CHS: Size 21.3-219.1 mm & Thickness 2.00-8.20 mm, SHS: Size 16X16-200X200 mm; RHS: Size 30X15-200X100 mm & Thickness 1.00-8.50 mm
TOLERANCES :
Round Tubes - Tolerances on dimensions Shaped Tubes - Tolerances on dimensions
Characteristics / Tolerances Characteristics / Tolerances
External Dimensions (D) : ±0.50% for 48.3mm & smaller, and External Dimensions (B/H) : ±0.50mm for 65mm or under, ±0.60mm for 65 - 90mm including,
±0.75% for 50.0mm and above ±0.80mm for 90 - 140mm including and ±1% for over 140mm
Wall Thickness (T) : ±10% of the specified wall thickness Wall Thickness (T) : ±10% of the specified wall thickness
Straightness (e) : 2.0 mm times of total length Concavity/convexity (x1/x2) : Included in the Flat Dimension Tolerances
Squareness of side (θ) : 90° ± 2°
Flattening Test : Radius of corners (R) : Shall not exceed more than 3 times of Specified Wall Thickness
a) Flatten upto 2/3 of O.D. for weld ductility; Twist (v)/Mtr. : 1.3mm for 40mm or under, 1.6mm for 40 - 65 mm, 1.8mm for 65 - 100mm, 2.2mm
b) Flatten upto 1/2 of O.D. for Parent Metal and for 100 - 150mm and 2.5mm for 150 - 200mm
c) Full flattening for lamination Straightness (e) : 2.0 mm times of total length
CHEMICAL COMPOSITION (%) MECHANICAL PROPERTIES-ROUND MECHANICAL PROPERTIES-SHAPE
Grade C Mn P Cu YS (MPa) UTS (MPa) %El YS (MPa) UTS (MPa)
S Max. %El Min
Max. Max. Max. Min. Min. Min. Min Min. Min.
A (Heat) 0.260 1.350 0.035 0.035 0.200
230 310 25 270 310 25
A (Product) 0.300 1.400 0.045 0.045 0.180
B (Heat) 0.260 1.350 0.035 0.035 0.200
290 400 23 315 400 23
B (Product) 0.300 1.400 0.045 0.045 0.180
C (Heat) 0.230 1.350 0.035 0.035 0.200
315 425 21 345 425 21
C (Product) 0.270 1.400 0.045 0.045 0.180
WORKMANSHIP : All Tubings are finished with Bare, Black Lacquer Coated or Galvanizing
MARKING : Each Pipe shall be stancilled as per ASTM A500 / Client Requirement
"TIGER/MADE IN UAE ASTM A500 GRADE A/B/C / SIZE--------------/LENGTH------------"

Value Addition: We are limiting the out-of-roundness for CHS section upto 0.50%D. For SHS/RHS section, side tolerances ±0.5%, Concavity/convexity 0.50mm max, External
Corner Profile 2.5T average, Twist 2mm/6mtr max and Straightness 1 mm per meter

You might also like