VLAN
Switch>en
Switch#
Switch#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#vlan 10
Switch(config-vlan)#name tt
Switch(config-vlan)#vlan 20
Switch(config-vlan)#name uu
Switch(config-vlan)#vlan 30
Switch(config-vlan)#name bb
Switch(config-vlan)#exit
Switch(config)#interface fa0/2
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 10
Switch(config-if)#int vlan 10
Switch(config-if)#ip add [Link] [Link]
Switch(config-if)#exit
Switch(config)#int fa0/3
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 20
Switch(config-if)#int vlan 20
Switch(config-if)#
Switch(config-if)#ip add [Link] [Link]
Switch(config-if)#exit
Switch(config)#
Switch(config)#int fa0/4
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 30
Switch(config-if)#int vlan 30
Switch(config-if)#
Switch(config-if)#ip add [Link] [Link]
Switch(config-if)#end
Switch#
Switch#show vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/1, Fa0/5, Fa0/6, Fa0/7
Fa0/8, Fa0/9, Fa0/10, Fa0/11
Fa0/12, Fa0/13, Fa0/14, Fa0/15
Fa0/16, Fa0/17, Fa0/18, Fa0/19
Fa0/20, Fa0/21, Fa0/22, Fa0/23
Fa0/24, Gig0/1, Gig0/2
10 tt active Fa0/2
20 uu active Fa0/3
30 bb active Fa0/4
1002 fddi-default active
1003 token-ring-default active
1004 fddinet-default active
1005 trnet-default active
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 0 0
10 enet 100010 1500 - - - - - 0 0
20 enet 100020 1500 - - - - - 0 0
30 enet 100030 1500 - - - - - 0 0
1002 fddi 101002 1500 - - - - - 0 0
1003 tr 101003 1500 - - - - - 0 0
1004 fdnet 101004 1500 - - - ieee - 0 0
1005 trnet 101005 1500 - - - ibm - 0 0
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
Remote SPAN VLANs
------------------------------------------------------------------------------
Primary Secondary Type Ports
------- --------- ----------------- ------------------------------------------
Switch#show ip int breif
Switch#show ip int brief
Interface IP-Address OK? Method Status Protocol
FastEthernet0/1 unassigned YES manual up up
FastEthernet0/2 unassigned YES manual up up
FastEthernet0/3 unassigned YES manual up up
FastEthernet0/4 unassigned YES manual up up
FastEthernet0/5 unassigned YES manual down down
FastEthernet0/6 unassigned YES manual down down
FastEthernet0/7 unassigned YES manual down down
FastEthernet0/8 unassigned YES manual down down
FastEthernet0/9 unassigned YES manual down down
FastEthernet0/10 unassigned YES manual down down
FastEthernet0/11 unassigned YES manual down down
FastEthernet0/12 unassigned YES manual down down
FastEthernet0/13 unassigned YES manual down down
FastEthernet0/14 unassigned YES manual down down
FastEthernet0/15 unassigned YES manual down down
FastEthernet0/16 unassigned YES manual down down
FastEthernet0/17 unassigned YES manual down down
FastEthernet0/18 unassigned YES manual down down
FastEthernet0/19 unassigned YES manual down down
FastEthernet0/20 unassigned YES manual down down
FastEthernet0/21 unassigned YES manual down down
FastEthernet0/22 unassigned YES manual down down
FastEthernet0/23 unassigned YES manual down down
FastEthernet0/24 unassigned YES manual down down
GigabitEthernet0/1 unassigned YES manual down down
GigabitEthernet0/2 unassigned YES manual down down
Vlan1 unassigned YES manual administratively down down
Vlan10 [Link] YES manual up up
Vlan20 [Link] YES manual up up
Vlan30 [Link] YES manual up up
Switch#
Switch#config t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#interface range f0/1-3
Switch(config-if-range)#switchport mode access
Switch(config-if-range)#switchport access vlan 10
Switch(config-if-range)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan20, changed state to down
Switch(config-if-range)#end
Switch#
%SYS-5-CONFIG_I: Configured from console by console
Switch#show vlan brief
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/5, Fa0/6, Fa0/7, Fa0/8
Fa0/9, Fa0/10, Fa0/11, Fa0/12
Fa0/13, Fa0/14, Fa0/15, Fa0/16
Fa0/17, Fa0/18, Fa0/19, Fa0/20
Fa0/21, Fa0/22, Fa0/23, Fa0/24
Gig0/1, Gig0/2
10 tt active Fa0/1, Fa0/2, Fa0/3
20 uu active
30 bb active Fa0/4
1002 fddi-default active
1003 token-ring-default active
1004 fddinet-default active
1005 trnet-default active
Switch#
%CDP-4-NATIVE_VLAN_MISMATCH: Native VLAN mismatch discovered on
FastEthernet0/1 (10), with Switch FastEthernet0/1 (1).
Switch#
Switch#
DHCP
Router>en
Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname selesh
selesh(config)#int g0/0/0
selesh(config-if)#ip add [Link] [Link]
selesh(config-if)#no sh
selesh(config-if)#
selesh(config-if)#exit
selesh(config)#ip dhcp excluded-address [Link] [Link]
selesh(config)#ip dhcp pool clients
selesh(dhcp-config)#network [Link] [Link]
selesh(dhcp-config)#default-router [Link]
selesh(dhcp-config)#dns-server [Link]
selesh(dhcp-config)#domain-name [Link]
selesh(dhcp-config)#exit
selesh(config)#
selesh(config)#exit
selesh#
%SYS-5-CONFIG_I: Configured from console by console
selesh#
selesh#wr
Building configuration...
[OK]
selesh#config t
Enter configuration commands, one per line. End with CNTL/Z.
selesh(config)#int g0/0/1
selesh(config-if)#ip add [Link] [Link]
selesh(config-if)#no shutdown
selesh(config-if)#
selesh(config-if)#exit
selesh(config)#ip dhcp excluded-address [Link] [Link]
selesh(config)#ip dhcp pool client
selesh(dhcp-config)#network [Link] [Link]
selesh(dhcp-config)#default-router [Link]
selesh(dhcp-config)#dns-server [Link]
selesh(dhcp-config)#domain-name [Link]
selesh(dhcp-config)#exit
selesh(config)#exit
selesh#
selesh#wr
Building configuration...
[OK]
selesh#
telnet
Router>en
Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#banner motd #wel come to INU ROUTER#
Router(config)#enable password inu1234
Router(config)#interface Gigabit Ethernet0/0
^
% Invalid input detected at '^' marker.
Router(config)#GigabitEthernet0/0
^
% Invalid input detected at '^' marker.
Router(config)#interface GigabitEthernet0/0
Router(config-if)#ip add [Link] [Link]
Router(config-if)#no shutdown
Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to
up
exit
Router(config)#line vty04
^
% Invalid input detected at '^' marker.
Router(config)#line vty 0 4
Router(config-line)#password inuvty1234
Router(config-line)#login
Router(config-line)#logging synchronous
Router(config-line)#exec-timeout 60
Router(config-line)#motd-banner
Router(config-line)#%IP-4-DUPADDR: Duplicate address [Link] on GigabitEthernet0/0,
sourced by 0002.171A.3BB5
%IP-4-DUPADDR: Duplicate address [Link] on GigabitEthernet0/0, sourced by
0002.171A.3BB5
Router(config-line)#motd-banner
