GENERAL NOTES
6- ANCHOR LENGTHS
PILES & TIE BEAMS GROUND ANCHORS 6.1- THE ANCHOR LENGTHS (GROUTED & UNGROUTED) SHOWN
GROUTING HOLE 3,4 OR 5 STRANDS
ON DRAWING ARE THE MINIMUM LENGTHS.
THE CONTRACTOR SHALL DETERMINE THE REQUIRED AS PER PIPE SIZE
1- GENERAL 1- GENERAL LENGTHS CAPABLE OF DEVELOPING THE LOADS IN (7) WEDGE
BELOW.
1.1- ALL DIMENSIONS ARE IN FEET & INCHES AND LEVELS ARE IN 1.1- ALL DIMENSIONS ARE IN FEET & INCHES AND LEVELS ARE IN
FEET & INCHES UNLESS NOTED OTHERWISE. FEET & INCHES UNLESS NOTED OTHERWISE.
7- ANCHOR LOADS
1.2- NO DIMENSION IS TO BE SCALE FROM THE DRAWINGS AND THE 1.2- THE COMPONENTS OF THE PRETRESSED GROUND ANCHOR
CONTRACTOR IS TO RECHECK ALL THE DIMENSIONS BEFORE CONSIST OF TE PRESTRESSING TENDONS,ANCHOR HOLDS,ANCHOR AS PER DRAWINGS.
START OF THE WORK HEAD (INCLUDING ALL NECESSARY HARDWARE), PVC PIPE,
GROUT TUBES AND SPACERS ETC.
1.3- PROJECT SPECIFICATIONS, BOQ DESCRIPTION WILL COVER
EXCEPT AS NOTED ON THE DRAWINGS. 1.3- THE OPERATIONS TO BE PERFORMED BY THE CONTRACTOR ARE
1.4- LEVEL ± 0.000 CONFORMS TO EXISTING ROAD LEVEL.
SHOWN ON DRAWINGS & REFERRED TO IN THE BOQ TABLE 1 150X150X22 TH
ANCHOR BLOCK
AND SPECIFICATIONS. M.S BEARING PLATE
2-CONCRETE BAR SPLICE (LAP LENGTHS) STRANDS
2.1- REINFORCED CONCRETE MATERIALS SHALL CONFIRM TO THE
FOLLOWING UNLESS OTHERWISE NOTED ON THE DRAWING: - 2- GROUT
2.1- GROUT SHALL BE NEAT CEMENT GROUT WITH BARS USED LAP LENGTHS
(i) CEMENT SHALL CONFIRM TO ASTM C-150 TYPE-1 A MAXIMUM W/C = 0.50 AND A 28 DAYS CRUSHING STRENGTH
(ORDINARY PORTLAND CEMENT). OF 3000 PSI.
(ii) AGGREGATE SHALL CONFIRM TO THE STANDARD
SPECIFICATIONS FOR CONCRETE AGGREGATE ASTM C33
2.2- ANCHORS SHALL BE POST GROUTED WITH DELAYED #3 1'-10½"
MULTIPLE GROUT INJECTIONS.
(iii) WATER SHALL BE FREE FROM OIL OR OTHER MATERIALS POST TENSION
THAT CAN ADVERSELY AFFECT CONCRETE STRENGTH OR ARRANGE MENT DETAIL
DURABILITY. 3- PRESTRESSING STEEL. #4 2'-6"
3.1- GROUND ANCHORS SHALL BE FABRICATED FROM SINGLE OR
2.2- CONCRETE SHALL HAVE THE FOLLOWING 28 DAYS MULTIPLE ELEMENTS OF ONE OF THE FOLLOWING
COMPRESSIVE CYLINDER STRENGTH AND SHALL CONFIRM TO PRESTRESSING STEELS: #6 3'-9"
BUILDING CODE REQUIREMENTS FOR REINFORCED CONCRETE
ACI- 318-05 (CYLINDER STRENGTH GIVEN IN PARENTHESIS)
(i) STEEL BARS CONFORMING TO AASHTO M 275 STANDARD BAR HOOKS:
(ii) SEVEN WIRE, LOW RELAXATION STRANDS CONFORMING
(i) PLAIN CEMENT CONCRETE (BLINDING) CONCRETE (1400 PSI) TO ASSHTO M 203. #8 5'-0" 12 db
(ii) PILES (4000 PSI) (iii) THE TENDON SHALL BE SIZED SO THAT THE DESIGN
(ii) WALER BEAMS/CAPPING BEAM (4000 PSI) LOAD DOES NOT EXCEED 60% OF THE SPECIFIED MINIMUM
4db> 2½"
TENSILE STRENGTH OF THE PRESTRESSING STEEL.
r
(iv) BREAKING LOAD OF 1/2"Ø STRAND MUST NOT BE LESS
THAN (18.73) METRIC TONNE
3- REINFORCEMENT
3.1- REINFORCEMENT SHALL CONFIRM TO ASTM A615-92 GRADE 60
4- ANCHOR HOLDS
4.1- ANCHOR HOLDS SHALL BE CONCRETE OR STEEL OR AS PER
3.2- CLEAR COVER TO REINFORCEMENT SHALL BE AS FOLLOWS THE DISCRETION OF THE CONTRACTOR. THE CONTRACTOR
(THE DIMENSIONS INDICATE THE CLEAR DISTANCE FROM THE SHALL SUBMIT THE DESIGN FOR THE APPROVAL OF THE db db
EDGE OF THE SECONDARY REINFORCEMENT (TIES OR STIRRUPS) ENGINEER.
TO THE OUTER CONCRETE SURFACE). FOR MAIN REINFORCEMENT
(i) PILES 1.5" 12 db
5- ANCHORAGE DEVICES 6 db
(ii) TIE BEAMS 1.5"
5.1- STRESSING ANCHORAGES WOULD BE A COMBINATION OF
5°
3.3- FOR BAR SPLICES (LAP LENGTHS) REFER TO TABLE-1. EITHER A STEEL BEARING PLATE WITH WEDGE PLATE AND 13
WEDGES ,OR A STEEL BEARING PLATE WITH A THREADED 6
r
db
r
ANCHOR NUT. ANCHORAGE DEVICE SHALL BE CAPABLE OF
DEVELOPMENT, SPECIFIED MINIMUM TENSILE STRESS.
5.2- ALL THE ACCESSORIES FOR ANCHORAGE DEVICE , # 6,7 OR 8 BARS.
SHALL BE PAINTED AND FABRICATED FROM STEEL
CONFORMING TO AASHTO M 183 (OR EQUIVALENT) OR MAY
BE A DUCTILE IRON CASTING CONFORMING TO ASTM A-36.
db db
db
FOR STIRRUPS & TIES.
FOR CONSTRUCTION
GENERAL NOTES.
KUWAIT MALL
BAHRIA TOWN LAHORE.
