Model E Staplers

INSTRUCTIONS FOR OPERATION AND MAINTENANCE

AWARNING:
OPERATOR AND OTHERS IN THE WORK AREA SHOULD ALWAYS WEAR SAFETY EYE PROTECTION WHEN
TOOLS ARE IN USE.
DO NOT PLACE HANDS BETWEEN STAPLER HEAD AND CLINCHER WHEN OPERATING MACHINE.
CARE SHOULD BE TAKEN WHEN REMOVING FACE PLATES AS SUPPORTER IS HELD IN PLACE ONLY BY
LUGS ON FACE PLATES, AND WILL BE EJECTED WITH CONSIDERABLE FORCE.

STANDARD E STAPLERS
Catalog Numbers
EHFS82MD EHA82MC
E LFS82MD EHA82MCMD
EHT82MC EHA83SC
EHT82MCMD EHA83SCMD
EHT83SC EHFS82
E HA87SC E H FS 82FR
EHAB2MCFR
LOADING:
Pull back feed spring until it is released from pusher. Let spring rest is left free to be removed, and wi I be forced up by plunger spring
against feed spring case, and remove pusher from rear end of core. unless spring is broken. Plunger spring and driver are then easily
Slide one or two strips of Stanley-Bostitch staples of proper size on- removed, cleaned, or replaced.
to care, and replace pusher and feed spring. Head is now ready for
use. TO REMOVE FACE PLATES:
Remove plunger as noted above, both upper and lower face plate
AWARNING: Do not place hands between stapler bolts, also any parts attached by means of lower face plate bolt such
as face plate shield. Pry apart gently — the face plates will come
head and clincher when operating machine. off and feed spring assembly can be lifted out. To replace face plates,
simply reverse this operation.
LUBRICATION:
Any machine will work easier and wear longer it kept clean and pro- IMPORTANT: — Face plate bolts should be brought up tight to avoid
perly oiled. Stanley-Bostitch staplers should be oiled frequently but play in head.
sparingly. A drop of oil applied from the point of a toothpick in chan-
nel for driver, on plunger spring, in hole in front of supporter, and
on core pivot pin will insure easy and trouble-free operation. AWARNING: Care should be taken when removing
CLOGGED STAPLES: face plates as supporter is held in place only by lugs on
If in some way staples have become clogged, they can be removed face plates, and will be ejected with considerable force.
by pressing supporter back and forcing staples out of groove. Be
sure wire grooves are free from broken pieces of wire. TO CHANGE OPENING ABOVE CLINCHER:
CLINCHER ADJUSTMENT: Adjustment can easily be made by raising or lowering the final treadle
stop. if the treadle strikes the floor before finishing the clinch, the
On Arm Type machines (Models EHA, & EHT), loosen clincher plate stroke can be shortened by adjusting the nuts above and below the
screw and adjust clincher with slide adjusting screws. Then tighten driving rod sleeve. It is important that the stroke on these machines
clincher plate screws. be properly adjusted on motor driven models, for if they are set too
tight, the motor will stall and throw off the cut-off switch.
On all other types, simply loosen the clincher binder screw, adjust
clincher by hand, and tighten binder screw. TO ADJUST FOR LIGHT OR HEAVY WORK:
MOVABLE CLINCHER MAINTENANCE: Simply move compensating lever spring to upper or lower hole.
It is particularly important to keep the clincher plates clean. Dust and TO ADJUST HEAD:
small pieces of material may get into this mechanism and hamper Should the stapler head be changed, adjustment foward or back may
its action. Do not put oil into the clincher plates as this tends to hold be required to bring the staple in line with the clincher. This is ac-
the dust. complished by turning the cone point core adjusting screws at the
The front and back plates are held together by studs fastened to the back of the core.
back plate, and fitted snugly into holes in front plate. When clincher ORDERING:
is opened, clincher slide and clincher points can be removed.
Replacement may be necessary in case of long or hard usage. These machines use different sizes of staples and make different
kinds of clinches. It is important therefore that correct part numbers
TO REMOVE PLUNGER ASSEMBLY: are used when ordering replacement parts. The charts and lists on
Detach feed spring from pusher and remove unused staples. Insert the following pages give names and number of parts .
thin screw driver under back of driver stop, and pry forward. Plunger
 MODEL E1000 STAPLER HEAD
FOR NARROW CROWN STAPLES
(SEE CHART BELOW)

FEED SPRING CASE SPACER - C68 FACE PLATE BOLT Nur - HN1032

PLUNGER SPRING - C42 FACE PLATE BOLT - UA3216.2

PLUNGER ASSEMBLY • E629A

DRIVER STOP SPRING SCREW - IJA3306.2

❑RIVER STOP SPRING SCREW FEED SPRING CASE - LEFT - C254

LOCK WASHER -5W10
FEED SPRING CASE - RIGHT - C255
DRIVER STOP SPRING PLATE - C499
NOTE COMPLETE FEED CASE AND
SPRING ASSEMBLY - C843A
DRIVER STOP SPRING - C418
PUSHER - C237
FEED SPRING • C845A
CORE ASSEMBLY E44BA
FEED SPRING CASE DOWEL - C57B
DRIVER STOP - C4OC

SUPPORTER SPRING GUIDE

DRIVER CORE ADJ. SCREW
C233
C244 C451
FACE PLATES SUPPORTER SPRING CORE ADJ. SCREW
C231 PLUNGER-C454
LEFT C262A
RIGHT C263A CORE ADJ. SCREW
FACE PLATE DOWEL C453
C338
STAPLE RETAINER FRONT - C283 SUPPORTER
SUPPORTER PIVOT PIN
C230
C235
SUPPORTER SPRING PLUNGER
C232

El000BHD
SK5019 (1.27mm x .48mm
114 (6.6mm)
3/8 (9.5mm)
 20 21 CLINCHERS & PARTS

I 45 46
T
SOLID CLINCHER 47 48 49
SEE DETAIL B 18

54 55 58 59

57 56 53 52 50 51

32 33,
34 USED ON EHA•SC{2J
60 61

18

40
SECTION A-A
SEE DETAIL A DETAIL B

SECTION B-B
76 80 79

54

77 76 75

' • " See section drawings

NOTE:
SECTION C-C * MOVABLE CLINCHER
1. • MOVABLE CLINCHER SADDLE
111

SEE BSA317CS & BSA13995

MOTOR DRIVE
SEE BSA317CS

112

SEE BSA1739S
 E SADDLE STAPLER
MODEL EHFS
MODEL ELFS
113
102
110 109

DETAIL A
E ARM & TABLE STAPLER
42 43 MODEL EHT-MC
MODEL EHT-SC
 MODEL E8200, E8300, E8600, E8700 STAPLER HEADS
FOR SCCR STAPLES (SEE CHART BELOW)

FACE PLATE NUT - HN1032

FEED SPRING CASE SPACER - C68
FACE PLATE BOLT - UA3216.2

PLUNGER SPRING - C42

PLUNGER ASSEMBLY - E629A FEED SPRING CASE

LEFT - C63
SCREW - UA3308.2
RIGHT - C64
LOCK WASHER - SW10

SPRING PLATE - C499 NOTE: COMPLETE FEED CASE AND SPRING ASSEMBLY - C843A

DRIVER STOP
PUSHER - MBA
SPRING - C419
CORE ADJUSTING
FEED SPRING - C238EA SCREW - C451
FEED SPRING CASE DOWEL • C679
DRIVER STOP - C40C

'DRIVER
fileVieMt
SUPPORTER SPRING - ESB
E10 - SPECIAL FOR E8600BHD
CORE ASSEMBLY
'VARIABLE - SEE CHART BELOW
C602BA 9/18
SUPPORTER
E4C WASHER - C867

(31:10 STAPLE GUIDE BLOCK SPRING - C6089

'FACE PLATES
STAPLE GUIDE BLOCK
LEFT & RIGHT
C604B (shown) C6050 (opposite side) VARIABLE PARTS

E8200BHD E8300EIHD E8600BHD E8700BHD

SCCA SCCR SCCF! SCCR
.025 (.64mm) 5019 (1.27rnm x .4emm) .019 (.48mm) .103 x .020
(2.6mm x .51mm)

PART 1/4 6.4mm) 1/4 (6.4mm) 1/4 16.4mm1 1/4 (6.4mm)

3/6 (9.5mm) 3/8 (9 5mm) 3/9 (9.5mm) 310 (9.5mm)
1/2 (12.7mm) 1/2 (12.7mm) 1/2 (12.7mm)
9/16 (14.3mm1 9/16 (14.3mm) 9/16 (14.3mm)

'DRIVER C19 C24 C29 C380

'FACE PLATE-LEFT C8200L C8300L C610D C8700L
'FACE PLATE-RIGHT C8200R C830OR 06110 C8700R
 MODEL E STAPLERS PARTS LIST
ITEM PART ITEM PART ITEM PART
NO. NO. DESCRIPTION NO. NO. DESCRIPTION NO. NO. DESCRIPTION

1 E105 BASE 40 E182 COMPENSATING LEVER PIVOT 79 LA8136.1 BOLT

2 FIN51618.7 NUT 41 UA5112.1 POST BRACE SCREW 80 E133 SPRING
3 LA5144.1 DRIVING ROD YOKE PIN 42 E103 POST BRACE LOW 1 81 E212 DRIVING ROD SLEEVE COLLAR
4 E1020 POST HIGH 43 E108 POST BRACE HIGH 1 82 E449 DRIVING ROD SLEEVE
5 E101B POST LOW 44 £710A TREADLE 1 83 E144 DRIVING ROD YOKE
6 LA513162 SCREW 45 E158 SOLID CLINCHER FLAT WIRE 84 E142 DRIVING ROD HIGH-POST
_
7 HN51618 NUT 46 E159 SOLID CLINCHER ROUND WIRE 85 £291 SADDLE TABLE LOCK
5 E175 DRIVING ROD SPRING 47 C119B IN-LINE CLINCHER PTS FLAT WIRE 86 F141C CORE PIVOT PART
9 E15 CORE LOCK PLATE SCREW 48 C120B 1N-LINE CLINCHER PTS ROUND WIRE 87 E292 SADDLE TABLE LOCK SCREW
10 LA5140.1 DRIVING ROD SLEEVE PIN 49 C96 i_ PASS-BY CLINCHER PTS ROUND WIRE 1 88 PW10 PLAIN WASHER
"11 E628 COMPENSATING LEVER SPRING PIN f 50 0136 CLINCHER SLIDE IN-LINE 1 89 E293 SADDLE TABLE PIVOT
12 851561 RETAINING RING 51 C97 CLINCHER SLIDE PASS-BY 90 UA5132.1 ARM SCREW
13 E625 SPACER *52 C126A AM CLINCHER PLATE W/ STUDS IN-LINE - 1 91 E241B TOGGLE LEVER RIGHT
.--
14 E169 DRIVING LEVER LINK BUSHING *53 C93CA 4{'M CLINCHER PLATE IN/ STUDS PASS-BY !:, 92 £329 TOGGLE LEVER LEFT
- ..i
15 UA51521 SCREW "54 C127 it\p,..64 CLINCHER PLATE WI HOLES IN-LINE :3 93 E194BA SLIDE
•16 E187 AUXILIARY SPRING 9/16 DIAMETER •55 C94 A .41 CLINCHER PLATE WI HOLES PASS-BY 1,-, 94 E196 PIVOT
"17 E183B COMP. LEVER SPRING 1-1/16 DIA. •• 56 C 9,f) CLINCHER PLATE WI STUDS IN-LINE 95 E192CA ARM
'18 E181 COMPENSATING LEVER ""57 C930A -•) /4) CLINCHER PLATE W/ STUDS PASS-BY 17. 96 E147D LEVER
19 E165 DRIVING LEVER SPRING *•58_ra1270cjti) CLINCHER PLATE WI HOLES IN-LINE 97 0033 SLIDE SCREW
20 E161A DRIVING LINK ""59 C9413 SA-A CLINCHER PLATE WI HOLES PASS-BY 3- 98 C136E1 LIFTER
21 851378 UA4156,1 CORE PIVOT SCREW 99 E209 TABLE
-RETAINING RING 60
'22 E149 CLINCHER LEVER SPRING 61 HN1420.13 NUT 100 E18B DOWEL
23 E195 SLIDE 62 E623A LEFT HAND DRIVING LEVER 101 0062 WORK GUIDE
24 See Item No's 45,46.47,48,4940,51,52,53.54,55,56,57,58,59 63 E624A RIGHT HAND DRIVING LEVER 102 E320A BACK GAUGE
25 LJA3810.1 CLINCHER PLATE SCREW 64 E606 SPACER 103 E301 TABLE
"26 E147B CLINCHER LEVER 65 F127 BUSHING 104 E306 FRONT TABLE BRACE
27 E197 SCREW 66 E12 DRIVING LEVER PIVOT BUSHING 105 E325 SCREW
28 E192A ARM 67 UA5152,1 TOGGLE LINK PIN 106 E308 BACK TABLE BRACE
'29 E196 CLINCHER LEVER PIVOT 68 SW516 LOCKWASHER 107 E314 BOLT
30 E18 DOWEL 69 El 74B TOGGLE LINK 108 SW516 WASHER
31 UA5120,1 ARM SCREW 70 E212 WASHER 109 E311 BOLT
'32 E177 TOGGLE LEVER LEFT 71 E199 BUSHING 110 SW10 WASHER
i "33 ' E241B TOGGLE LEVER RIGHT 72 F171 DRIVING LEVER TOGGLE BUSHING 111 EK5 SAFETY HAND COVER
34 £211 TOGGLE LEVER LEFT & RIGHT 73 UA6160.1 TREADLE PIVOT i 112 EK6 SAFETY FOOT COVER
•35 E194A CLINCHER OPERATING SLIDE 74 HN3816.7 NUT 113 LA2406.1 SCREW
"36 E153 CLINCHER OPERATING SLIDE GUIDE 75 E106 BASE BOLT 114 E189 CLINCHER LOCK NUT
'37 UA5314.1 SCREW 76 HN1213.2 NUT I 115 UA3812.2 CLINCHER SCREW
'38 HN1618.2 NUT 77 LW12.2 LOCKWASHER
39 UA5128.1 TOGGLE LEVER PIVOT 78 UA8516.1 BASE BOLT BINDER SCREW
 LIMITED WARRANTY
Stanley-Bostitch, Inc., warrants to the original retail purchaser that this product is free from defects in material and
workmanship, and agrees to repair or replace, at Stanley-Bostitch's option, any defective product within 90 days
from the date of purchase. This warranty is not transferable. It only covers damage resulting from defects in material
or workmanship, and it does not cover conditions or malfunctions resulting from normal wear, neglect, abuse or
accident.
THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES. ANY WARRANTY OF MERCHANTA-
BILITY OR FITNESS FOR A PARTICULAR PURPOSE IS LIMITED TO THE DURATION OF THIS WARRANTY.
STANLEY-BOSTITCH SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental
or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you
specific legal rights, and you may also have other rights which vary from state to state.
To obtain warranty service, you must return the product at your expense together with proof of purchase to a Stanley-
Bostitch Regional warranty repair center listed below or you may call us at 1-800-832-3080 for the location of addi-
tional authorized warranty service locations in your area.
EASTERN: Stanley-Bostitch, Inc., 1 Feltloc Lane, East Greenwich, R.I. 02818
MIDWEST: Stanley-Bostitch, Inc., 420 South Kitley Avenue, P.O. Box 19329, Indianapolis, IN 46219
SOUTHERN: Stanley-Bostitch, Inc., 1105 Satellite Blvd. Suite 105, Suwanee, GA 30174
WESTERN: Stanley-Bostitch, Inc., 6941 West Goshen Avenue, P.O. Box 111, Visalia, CA 93277

To find the Stanley-Bostitch service location nearest you, please call:

1-800-832-3080

STANLEY BOSTITCH Litho in U.S.A.

EISA309GS REV E 9/92 Stanley Fastening Systems
 BOST1TCH®
INSTRUCTIONS FOR OPERATION AND MAINTENANCE
OF MODEL E STAPLERS

WARNING:

OPERATOR AND OTHERS IN THE WORK AREA SHOULD ALWAYS WEAR SAFETY EYE PROTECTION WHEN
TOOLS ARE IN USE.
DO NOT PLACE HANDS BETWEEN STAPLER HEAD AND CLINCHER WHEN OPERATING MACHINE.
f -- CARE SHOULD BE TAKEN WHEN REMOVING FACE PLATES AS SUPPORTER IS HELD IN PLACE ONLY
BY LUGS ON FACE PLATES, AND WILL BE EJECTED WITH CONSIDERABLE FORCE.

LOADING:
Pull back feed spring until it Is released from pusher. Let spring rest is left free to be removed, and will be forced up by plunger spring
against feed spring case, and remove pusher from rear end of core. unless spring is broken. Plunger spring and driver are then easily
Slide one or two strips of Bostitch staples of proper size onto core, removed, cleaned, or replaced.
and replace pusher and feed spring. Head is now ready for use.
TO REMOVE FACE PLATES:
Remove plunger as noted above, both upper and lower face plate
WARNING: Do not place hands between stapler head
bolts, also any parts attached by means of lower face plate bolt such
and clincher when operating machine. as face plate shield. Pry apart gently — the face plates will come
LUBMATION: off and feed spring assembly can be lifted out. To replace face plates,
simply reverse this operation.
—nine will work easier and wear longer if kept clean and pro-
perly oiled. Bostitch staplers should be oiled frequently but sparing- IMPORTANT: — Face plate bolts should be brought up tight to avoid
ly. A drop of oil applied from the point of a toothpick in channel for play in head.
driver, on plunger spring, in hole in front of supporter, and on core
pivot pin will insure easy and trouble-free operation.
I WARNING: I Care should be taken when removing face
CLOGGED STAPLES: plates as supporter is held in place only by lugs an face
If in some way staples have become clogged, they can be removed plates, and will be elected with considerable force.
by pressing supporter back and forcing staples out of groove. Be
sure wire grooves are free from broken pieces of wire. TO CHANGE OPENING ABOVE CLINCHER:
Adjustment can easily be made by raising or lowering the final treadle
CLINCHER ADJUSTMENT:
stop. If the treadle strikes the floor before finishing the clinch, the
On Arm Type machines (Models EHA, & EHT), loosen clincher plate stroke can be shortened by adjusting the nuts above and below the
screw and adjust clincher with slide adjusting screws. Then tighten driving rod sleeve. it Is important that the stroke on these machines
clincher plate screws. be properly adjusted on motor driven models, for if they are set too
On all other types, simply loosen the clincher binder screw, adjust tight, the motor will stall and throw off the cut-off switch.
incher by hand, and tighten binder screw.
TO ADJUST FOR LIGHT OR HEAVY WORK:
MOVABLE CLINCHER MAINTENANCE: Simply move compensating lever spring to upper or lower hole..
It is particularly important to keep the clincher plates clean. Dust and
TO ADJUST HEAD:
small pieces of material may get into this mechanism and hamper
its action. Do not put oil into the clincher plates as this tends to hold Should the stapler head be changed, adjustment toward or back may
the dust. be required to bring the staple in line with the clincher. This is ac-
complished by turning the cone point core adjusting screws at the
( he front and back plates are held together by studs fastened to the back of the core.
back plate, arid fitted snugly into holes in front plate. When clincher
is opened, clincher slide and clincher points can be removed. ORDERING:
Replacement may be necessary in case of long or hard usage. These machines use different sizes of staples and make different
kinds of clinches. It is important therefore that correct part numbers
TO REMOVE PLUNGER ASSEMBLY:
are used when ordering replacement parts. The charts and lists on
nqtacil feed spring from pusher and remove unused staples. insert the following pages give names and number of parts.
r -,w driver under back of driver stop, and pry forward. Plunger
MODEL E STAPLER HEADS
FOR SCCR STAPLES

FACE PLATE NUT - HN1032

FEED SPRING CASE SPACER - CU
FACE PLATE BOLT - UA3216.2

PLUNGER SPRING • C42

PLUNGER ASSEMBLY - MBA FEED SPRING CASE

LEFT - 063
SCREW - UA3306.2
RIGHT - C134
LOCK WASHER - SW10

SPRING PLATE - 0490 NOTE: COMPLETE FEED CASE AND SPRING ASSEMBLY - C843A

DRIVER STOP
PUSHER - C658A
SPRING - C4113
CORE ADJUSTING
FEED SPRING - C238EA SCREW-C451
FEED SPRING CASE DOWEL - C678
DRIVER STOP - C40C

'DRIVER
/MAW
SUPPORTER SPRING - EBB
El - SPECIAL FOR E11400EIHD
CORE ASSEMBLY
C602BA 9116
SUPPORTER
E4C WASHER-C867

COM STAPLE GUIDE BLOCK SPRING - C130815

'FACE PLATES STAPLE GUIDE BLOCK
LEFT & RIGHT
C6049 [shaven} C8058 (opposite We)

•VARIAIRE - SEE CHART BELOW (Di 0- D

ocic)
w), do VARIABLE PARTS goZ) ovlica 17‘
4•'d0.) CLa W
E8200BHD E8300BHD E8600BHD E8700BHD
SCCR SCCR SCCR SCCR
.025 (.64mm) 5019 (1.27mm x .48mm) .019 (.48mm) .103 x .020
(2.6mm x .51mm)

PART 1/4 (6.4mm) 1/4 (6.4mm) 114 (6.4mm) 1/4 (6.4mm)

3/8 (9.5mm) 3/8 (9.5mm) 3/0 (9.5mm) 3/8 (9.5mm)
1/2 (12.7mm) 1/2 (12.7mm) 1/2 (12.7mm)
9/18 (14.3mm) 9/16 (14.3mm) 9/16 (14.3mm)

DRIVER C19 C24 C29 C380

FACE PLATE-LEFT C8200L C8300L C6100 C8700L
FACE PLATE-RIGHT C8200R C8300R C611D C8700R

-2-
 MODEL E STAPLER HEADS - FOR NARROW CROWN STAPLES
FEED SPRING CASE SPACER - C68 FACE PLATE BOLT NUT - HN1032

PLUNGER SPRING - C42

FACE PLATE BOLT - UA3218.2

PLUNGER ASSEMBLY - E82111A

DRIVER STOP SPRING SCREW - UA3306.2
DRIVER STOP SPRING SCREW FEED SPRING CASE - LEFT - C254
LOCK WASHER - SW10
FEED SPRING CASE - RIGHT - C255
(7- DRIVER STOP SPRING PLATE - C499
NOTE: COMPLETE FEED CASE AND
SPRING ASSEMBLY - C843A
DRIVER STOP SPRING - C41B
PUSHER - C237
FEED SPRING - C845A CORE ASSEMBLY • E44BA
FEED SPRING CASE DOWEL - C137B
DRIVER STOP - C40C

SUPPORTER SPRING GUIDE

'DRIVER CORE ADJ. SCREW
SUPPORTER SPRING C451
•FACE PLATES CORE ADJ. SCREW
LEFT & RIGHT PLUNGER—CAS4
CORE AD). SCREW
FACE PLATE DOWEL C453
• SUPPORTER
cus
STAPLE RETAINER FRONT • 0253 • SUPPORTER PIVOT PIN

'SUPPORTER SPRING PLUNGER

DIAGRAM SHOWS ENOS HEAD

VARIABLE PARTS

PART El 000BHD E41300BHD E4800BH0

SK5019 3/8 SK5019 3/8 SK19 1/4; 3/8
(9.5mm) (9.5mm) (8.4mm; 9.5mm)
FACE PLATE-LEFT C262A C512A C596A
FACE PLATE-RIGHT C263A C513A C597A
DRIVER C244 C244 C227B
SUPPORTER 0230 NONE 0230
SUPPORTER SPRING 0231 NONE C231
SUPPORTER SPRING
PLUNGER C232 NONE 0232
SUPPORTER SPRING
GUIDE C233 NONE C233
SUPPORTER PIVOT PIN 0235 NONE 0235
iteus:e

-3-
 F9400ECHD SERIES WIDE CROWN STAPLING HEAD
FOR SW9043 7/16, 5/8, 3/4, T/9 STAPLES
F9423 DRIVER DRIVER ASSEMBLY
HEAD F9469A
1-11,11420 9 NUT
1.1.44328.1 SO
85981 RETAINING RING
F9412 SPRING
PLATE F9450 SPRING
F9470 SPRING GUIDE
F9413 CRIVER
STOP 946B FRAME
SPRING

C40CFa

Di 6149A P'.S-ER
UA4810.5 SCRE
UB2912.3 COTTER PI
F9452 SUPPCRTE

U4313105

F9466 FRONT
GUIDE

REAR GUIDE
(2) F9465 UA48121
9463A MAGAZINE ASSEMBLY DI4305 PUSHER SPRING
F9464 PIMCI1 BLOCK
A360(1.16 SCREW

MACHINE PARTS SPECIAL TO MODEL E94HA

(see diagram on page 5)
PART DESCRIPTION PART DESCRIPTION
NUT-DRIVING LEVER C957N DRIVER HEAD PIN
F173 SPACER (short) DRIVING LEVER F9426A DRIVING LINK
£1796 SPACER-TOGGLE LINK C957M PIVOT PIN ADAPTER
£211 TOGGLE LINK F9440A- DRIVING LEVER-LEFT
£212 TOGGLE LINK PIN COLLAR F9441A DRIVING LEVER-RIGHT
E604 CLINCHER F9443 SPACER (long) DRIVING LEVER
E614 SPACER-ADAPTER PIVOT PIN UA5156.2 SCREW-DRIVING LEVER-TOGGLE
EK3 SPECIAL TO ORDER 851562 RETAINING RING (pivot pin)
FLAT TYPE CLINCHER
(FC95 type clincher) 85017 RETAINING RING (driver head)
 01111111M10 C2P
DRIVING LEVER SPRING 'IN-LINE CLINCHER POINTS
ADAPTOR PIVOT PIN
Cs5711 (E94HA ONLY) ENO CH= — FOR FLAT WIRE
C1201 — FOR ROUND WIRE
'PASS-BY CLINCHER POINTS
DRIVING LINK
C91 — FOR ROUND WIRE
0=0
RETAINING RING
951592 CORE PIVOT SCREW RETAINING RING
UM 36.1 851379

NUT — HN1429.13 SOLID CLINCHER 'CLINCHER PLATE •CUNCHER PLATE

WITH STUDS WITHOUT STUDS
ETU—FM FLAT WIRE 'CLINCHER SLIDE
Es24A R.H. DRIVING LEVER C126A—IN-LINE C127-0N-LINE
E623A LH. DRIVING LEVER
(SHOWN)
~NA Eno — FOR ROUND WIRE C93CA—[Link]
•FOR SADDLE STAPLER
C131—IN-LINE
C97 —Pasabv
C14—Pmby
'FOR SADDLE STAPLER
COMPENSATING LEVER CLINCHER LEVER (SEE PAGE el
A (SEE PAGE 8)
E181 • SPRING C1211BA—IN-LINE • MOVEABLE CLINCHER PARTS C127E—IN-LINE
'E1111 C93DA—Pauby [Link]—Pasaby
COMPENSATING LEVER SPRING LIRE
E111311 ' 1193
MOVABLE IN-UNE CLINCHER KITS
AUXILIARY SPRING FOR ROUND WIRE ONLY
E1125 SPACER 8117 •
CLINCHER PLATE SCREW EKI FOR ARM & TABLE STAPLERS
HI151014.7 NUT BUSHING uK31110.1
CA5152.1 SCREW E.199 EK2 FOR SADDLE STAPLER
SCREW
CLINCHER LEVER PIVOT E197
TOGGLE LINK PIN *ON •
UA5152.1 DOWEL ARM
Eli E192A CLINCHER LEVER
WASHER •E141! NOTE:['] MOVABLE CLINCHER ONLY
E212 ARM SCREW — UA51211.1
(11 ELFS ONLY
torii;!1,01
TOGGLE LEVER
TOGGLE LINK *1177 — LEFT
(1748 •E24111 — RIGHT
8211 011 ENA-SC (1)
RETAINING RING
1151581

COMPENSATING LEVER CLINCHER OPERATING SNIDE

SPRING PIN •E194A
1628 •
NUT
KN51419 7 DRIVING ROD SPRING
• Elm
SCREW TOGGLE LEVER PIVOT
CA5116.2 uA5124.1
OR. ROD SLEEVE PIN Nul
CA5140.1. 11115161$ POST BRACE-LOW
POST•LOW • • 0103 CLINCHER OPERATING SLIDE
POST BRACE•HIGH GUIDE
NUT POST HIGH EEGS •(153
H II 51918. [1020 SCREW
'CA5314.1

a DRIVING ROD
NUT
'1•1151111.2

YOKE PIN
LIA5T44.1 TREADLE
E.119A

E ARM STAPLER MODELS

EHA - MC - MOVABLE CLINCHER
EHA - SC - SOLID CLINCHER
TREADLE PIVOT LIA61801
BASE 8105
NUT
 E2111 SADDLE TABLE LOCK
P141D CORE PIVOT PART SCREW
UA2404.1
!2B2 SADDLE TABLE LOCK SCREW Emr BitiT BACK G4U41*
PW10 PLAIN WASHER E311 E320.4
WASHER SW10
SADDLE TABLE PIVOT

w0FICOLIO1

TABLE TABLE
CLIIICHER 1301
SEE TABLE 1301

FRONT
TABLE BRACE
Lwa
TABLE
EWA BACK
BOLT .1 NUT TABLE BRACE
(314 MOB
LIFTER TOGGLE LEPER WASHER SW510
013011 12410-RICHT EWE
E321-LETT
WW1 ICRTAT
0033
E ARM & TABLE STAPLER
LEPER
114/0
ELIDE
MODELS EHT-MC
ARM 11941A EHT-SC
[19201
PIVOT EMS (DIM
Ern E103 (ELFS)
'SPECIAL TO ORDER ITEMS
E SADDLE STAPLER
MODELS EH FS
ELFS

NOTE: SEE PAGE 5 FOR PARTS NOT LISTED ON THIS PAGE.

-6-
• THE FOLLOWING PARTS ARE NOT SHOWN IN DIAGRAMS:
E12 Driving Lever Pivot Bushing F171 Driving Lever Toggle Bushing
E15 Core Lock Plate Screw LW12.2 Lock Washer — Base Bolt
E18B Arm Locating Dowel (Saddle Arm) SW10 Lock Washer — Cl. Plate Screw
E106 Base Boit SW516 Lock Washer — Arr.1 Screw
E169 Driving Lever Link Bushing UA5132.1 Alm Screw (Saddle Arm)
E182 Compensating Lever Pivot UA8516.1 Binder Screw — Base Boit
E189 Clincher Lock Nut (Saddle Arm)
E249 Clincher Screw

STANDARD E STAPLERS
CATALOG NUMBER HEAD CLINCHER PARTS
EHA82MC EB200BHD C93CA C97, C94
EHA82MCMD E8200BHD MCA, C , C97, C94
EHA83SC E83008HD E158
EHA83SCMD E8300BHD E158
EHFS82 E8200BHD C93DA, C96. C97, C94B
EHFS82MD E8200BHD C93DA, C96, C97, C94B
ELFS82MD E82000H0 C93DA, C98, C97, 094B
EHT82IAC 862008HD C93CA, C98, C97, C94
EHT82MCMD EB200BHD C93CA, C96, C97, C94
EHT83SC E8300BHD E158
EHT83SCMD E8300BHD E158
E94HA F9400ECHD E604 (solid)

-7-
 LIMITED WARRANTY
1
Stanley-Bostitch, inc., warrants to the original retail purchaser that this product is free from defects in material and
workmanship, and agrees to repair or repine, at Bostitch's option, any defective product within 90 days from the
date of purchase. This warranty is not transferable. It only covers damage resulting from defects in material or workman-
ship, and it does not cover conditions or malfunctions resulting from normal wear, neglect, abuse or accident.
THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES. ANY WARRANTY OF MERCHANTA-
BILITY OR FITNESS FOR A PARTICULAR PURPOSE IS LIMITED TO THE DURATION OF THIS WARRANTY.
BOSTITCH SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental
or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you
specific legal rights, and you may also have other rights which vary from state to state.
To obtain warranty service, you must return the product at your expense together with proof of purchase to your
nearest Bostitch office, check your telephone directory or write to your nearest Bostitch Regional office; the four
Bostitch Regional Offices in the United States are:
EASTERN: Stanley-Bostitch, Inc., 1 Feltloc Lane, East Greenwich, R.I. 02818
MIDWEST: Stanley-Bostitch, Inc., 420 South Kitley Avenue, P.O. Box 19329, Indianapolis, IN 46219
SOUTHERN: Stanley-Bostitch, Inc., 3623 Clearview Parkway, Atlanta, GA 30340
WESTERN: Stanley-Bostitch, Inc., 6941 West Goshen Avenue, P.O. Box 111, Visalia, CA 93277

BOSTITCH SERVICE LOCATIONS & WAREHOUSES

ARIZONA KENTUCKY OHIO

Phoenix 602-257-80431- Somerset 606-679-6842 Cleveland 216-433-1060
Cincinnati 513-825-T771
CALIFORNIA LOUISIANA
Fullerton 714-773-5592? New Orleans 504-764-1533 PENNSYLVANIA
Visalia' 209-651-40111- Philadelphia 215-643-6201?
MASSACHUSETTS
COLORADO Woburn 617-933-1157? PUERTO RICO• 809-781-6216
Denver• 303373-4874t
MICHIGAN RHODE ISLAND
FLORIDA Detroit 313-669-0805 East Greenwich• 401-885-07001-
Ft. Lauderdale* 305-979-5710 Grand Rapids 610-452-1435
Tampa' 813-621-4791 TENNESSEE
MINNESOTA Memphis 901-365-7200
GEORGIA Minneapolis 612-835.2440
Atlanta* 404-458-2324 TEXAS
MISSOURI Dallas* 214-620-8770
HAWAII St. Louis 314-567-6120 Houston 713-240-3697
Honolulu' 808-836.4568
NEW JERSEY UTAH
ILLINOIS Pine Brook 201.575-89961' Salt Lake City 801.964-6097?
Skokie 312.470-8400
NEW YORK VIRGINIA
INDIANA Syracuse 315.437-0237? Richmond 804-222-3106?
Indianapolis 317-353-2171
NORTH CAROLINA WASHINGTON
KANSAS Charlotte 704-376-4402 Seattle 206-575-0656t
Kansas City 913-894-1066 High Point 919-887-4055

'Denotes Warehousing Locations

Ns@ this number for REPAIR SERVICE only. For customer service in Construction, Mass Market and Graphic Arts Industries
call TOLLFREE 1-800-558-8898, all others call 1-800-832-3080.

STANLEY BOSTITCH
BSA309GS REV A 5/89 Litho in U.S.A.
A Subsidiary of The Stanley Works