BEKG 1233
PRINSIP INSTRUMENTASI DAN
PENGUKURAN
Time: 3.00 p.m
Date: 17-3-2020
4/14/2023 Chapter 4 : Oscilloscope 1
5.0 OSCILLOSCOPE
Objectives:
➢ List the major subsystems of an oscilloscope
➢ Do basic operation and calibrate an oscilloscope
➢ Determine the frequency and amplitude of a signal
displayed on the CRT screen
➢ Compute phase angle
4/14/2023 Chapter 4 : Oscilloscope 2
5.1 Introduction (Cathode Ray
Oscilloscope/Tube)
➢ Cathode Ray Oscilloscope (CRO) generally referred to as
the oscilloscope is probably the most versatile electrical
measuring instrument.
➢ The electrical parameters can be observed with the
oscilloscope are ac or dc voltage, indirect measurement of
ac or dc current, time, frequency, phase angle and a wide
range of waveform evaluations such as rise time, fall time,
ringing and overshoot.
4/14/2023 Chapter 4 : Oscilloscope 3
4/14/2023 Chapter 4 : Oscilloscope 4
Cont’d…
➢ Physical quantities such as pressure, strain, temperature,
and acceleration can be measured by using a transducer to
convert the physical parameter to an equivalent voltage.
➢ Consists of the following major subsystems:
o Cathode-ray tube or CRT
o Vertical amplifier
o Horizontal amplifier
o Sweep generator
o Trigger circuit
o Associated Power Suplies
4/14/2023 Chapter 4 : Oscilloscope 5
Cont’d…
➢ The oscilloscope is basically an electron beam voltmeter
The heart of the oscilloscope is the CRT which makes the
applied signal visible by the deflection of a thin beam of
electrons.
➢ Practically the electron has no weight and no inertia
therefore the beam of electrons can be moved to follow
varying at a rate of millions of times/second. Thus the
electron beam follows rapid variations in signal voltage
and traces a visible path on the CRT screen.
4/14/2023 Chapter 4 : Oscilloscope 6
Cont’d…
➢ In this way rapid variations, pulsations or transients are
reproduced an the operator can observe the waveform as
well as measure amplitude at any instant of time. It can be
used in any field where a parameter can be converted into a
proportional voltage for observation, e.g. meteorology,
biology and medicine
4/14/2023 Chapter 4 : Oscilloscope 7
Cont’d…
Figure 5.1 Basic cathode ray tube construction
4/14/2023 Chapter 4 : Oscilloscope 8
5.2 Basic operation of Oscilloscope
➢ The CRO depends on the movement of an electron beam,
which is bombarded on the screen coated with a
fluorescent material, to produce a visible spot. If the
electron beam is defected on the vertical(x-axis) and
horizontal (y-axis) axis, a two dimensional display is
produced. The beam is deflected at a constant rate relative
of time along the x-axis and is deflected along the y-axis in
response to a signal, such as a voltage. This produces a
time-dependent variation of the input voltage.
4/14/2023 Chapter 4 : Oscilloscope 9
Cont’d…
➢ A beam of electrons is generated by the cathode and
directed to the screen, causing the phosphor coating on the
screen to glow where the electrons strike. The electron
beam is deflected vertically and horizontally by externally
applied voltages.
Triode Section
➢ Consists of cathode, a grid and anode. The grid is a nickel
cup with a hole in it, almost completely encloses the
cathode. The cathode (nickel) is cylinder shape with a flat,
oxide coated, electron emitting surface directed toward the
hole in the grid. Cathode heating is provided by and inside
4/14/2023 Chapter 4 : Oscilloscope 10
filament.
Cont’d…
➢ The cathode is typically held at approximately -2kV, and
the grid potential is adjustable from approximately -2000V
to -2050V.
➢ The grid-cathode potential controls the electrons flow from
the cathode and thus controls the number of electrons
directed to screen. In otherworld the grid potential control
is a brightness control.
➢ A large number of electrons striking one point will cause
the screen to glow brightly otherwise a small number will
produce a dim glow.
4/14/2023 Chapter 4 : Oscilloscope 11
Cont’d…
➢ The first anode (A1) open at one end closed at the other
end, with a hole at the center of the close end. Since A1 is
grounded and the cathode is at a high –ve potential, A1 is
highly +ve with respect to the cathode.
➢ This causes electrons to be accelerated from the cathode
through the holes in the grid and anode to the focusing
section.
➢ In otherword A1 provides the accelerating field to draw the
electrons from cathode and the hole in A1 limits the initial
cross section of the electron beam.
4/14/2023 Chapter 4 : Oscilloscope 12
Cont’d…
Focusing Section
➢ The focusing electrodes A1, A2, A3 are referred to as an
electron lens. The function of the electrons lens is to focus
the electrons to a fine point on the screen. A3 and A1 are
held at ground potential while A2 is adjustable around -
2kV.
➢ The result of the potential difference between anodes is
called equipotential lines. Line 1 might have -700V while
line 2 might be -500V. On crossing the equipotent lines,
the electrons experience a force that changes their direction
of travel toward right angles with respect to the
equipotential lines. The shape of the line within A1
produces a convergentChapter
4/14/2023 force on the electron beam and13
4 : Oscilloscope
those within A produce a divergent force.
Cont’d…
Figure 5.2 The potential difference between electrodes A1, A2, A3 set
up equipotential lines that exert convergent and
divergent forces on the electron beam.
4/14/2023 Chapter 4 : Oscilloscope 14
Cont’d…
Deflection Section
➢ If the horizontal and vertical plates were grounded or left
unconnected, the beam of electrons would pass between
each pair of plates and strike the center of the oscilloscope
screen. There would produce a bright glowing point.
➢ When one plate of a pair of deflecting plates has a +ve
voltage and the other one has a –ve potential, the electrons
in the beam are attracted toward the +ve plate and repelled
from the negative plate.
4/14/2023 Chapter 4 : Oscilloscope 15
Cont’d…
➢ This plates are arranged in two pairs, H1 and H2 for
deflecting the beam horizontally and V1 and V2 for
deflecting it vertically. (Figure 5.2)
➢ When the plates are at zero voltage the beam is mideway
between them and the spot is in the center of the screen.
➢ When H1 is +ve with respect to the cathode (and all other
plates are at zero voltage), it attracts the beam and the spot
moves horizontally to the left. When H2 is +ve, it attract
the beam and spot moves horizontally to the right.
➢ When V1 +ve, the spot moves vertically upward and when
4/14/2023 Chapter 4 : Oscilloscope 16
V2 +ve, the spot moves downward.
5.3 Measurement of Voltage,
Frequency and Phase Angle
➢ The range applications of an oscilloscope varies from basic
voltage measurement and waveform observation to highly
specialist applications in all areas of science, engineering
and technology.
5.3.1 Voltage Measurement
➢ The most direct voltage measurement made with
oscilloscope is the peak to peak value. The rms value can
then be easily calculated from the p-p value.
4/14/2023 Chapter 4 : Oscilloscope 17
Cont’d…
➢ To measure the voltage from the CRT display, one must
observe the setting of the vertical attenuator express in
V/div and the peak to peak deflection of the beam, i.e. the
number of divisions. The peak to peak value of voltage is
then computed as
Volts
VP − P = no. of div
Div
4/14/2023 18
Chapter 4 : Oscilloscope
Cont’d…
➢ 5.3.2 Frequency and phase Measurement
➢ The period and frequency of periodic signals are easily
measured with an oscilloscope. The waveform must be
displayed such that a complete cycle is displayed on the
CRT screen. Accuracy is generally improved if a single
cycle displayed fills as much of the horizontal distance
across the screen as possible. The period is calculated as :
time no. of div
T= Frequency determination: f = 1/T
div cycle
4/14/2023 Chapter 4 : Oscilloscope 19
Cont’d…
➢ Phase difference
Phase difference, = (phase difference in division) x (degrees/div)
Example
From figure bellow, input signal of A and B is set as:
Volt/Div: 100mv/Div and Time/Div: 0.5ms/Div
4/14/2023 Chapter 4 : Oscilloscope 20
4/14/2023 Chapter 4 : Oscilloscope 21
4/14/2023 Chapter 4 : Oscilloscope 22
4/14/2023 Chapter 4 : Oscilloscope 23
4/14/2023 Chapter 4 : Oscilloscope 24
4/14/2023 Chapter 4 : Oscilloscope 25
4/14/2023 Chapter 4 : Oscilloscope 26
4/14/2023 Chapter 4 : Oscilloscope 27
5.4 Lissajous figures
➢ If we allow one AC signal to deflect the beam up and
down (connect that AC voltage source to the "vertical"
deflection plates) and another AC signal to deflect the
beam left and right (using the other pair of deflection
plates), patterns will be produced on the screen of the CRT
indicative of the ratio of these two AC frequencies. These
patterns are called Lissajous figures and are a common
means of comparative frequency measurement in
electronics.
4/14/2023 Chapter 4 : Oscilloscope 28
Cont’d…
Examples:
➢ Lissajous figure formed by two AC voltages in phase
(same frequency) with each other:
4/14/2023 Chapter 4 : Oscilloscope 29
Cont’d…
➢ If the two AC voltages are not in phase with each other i.e.
phase shift is exactly 90o between the two signals, and if
their amplitudes are equal:
4/14/2023 Chapter 4 : Oscilloscope 30
Cont’d…
➢ Finally, if the two AC signals are directly opposing one
another in phase (180o shift), we will end up with a line
again, only this time it will be oriented in the opposite
direction:
4/14/2023 Chapter 4 : Oscilloscope 31
Cont’d…
➢ When we are faced with signal frequencies that are not the
same, Lissajous figures get quite a bit more complex.
Consider the following examples and their given
vertical/horizontal frequency ratios:
4/14/2023 Chapter 4 : Oscilloscope 32
Cont’d…
➢ The more complex the ratio between horizontal and
vertical frequencies, the more complex the Lissajous
figure. The following figure illustration of a 3:1 frequency
ratio between horizontal and vertical:
4/14/2023 Chapter 4 : Oscilloscope 33
Cont’d…
➢ and a 3:2 frequency ratio (horizontal = 3, vertical = 2):
Mathematic expression:
Fy No of Horizontal tangencies
= No of Vertical tangencies
Fx
4/14/2023 Chapter 4 : Oscilloscope 34
