Product Description Sheet

1001 Trout Brook Crossing

Rocky Hill, CT 06067-3910
Telephone: (860) 571-5100
Hysol® Product 9430
FAX: (860) 571-5465
Industrial Products, October 2001

Description Peel Strength ASTM D 3167 Etched Aluminum, pli

Loctite® Hysol® 9430 is a modified epoxy adhesive that attains 3 Days @ 77ºF 60
structural properties after room temperature cure. This two-part
adhesive is formulated to give very high peel strength coupled
with excellent shear strength. Hysol 9430 bonds are resistant to GENERAL INFORMATION
water, salt spray and many common industrial fluids. The tough, This product is not recommended for use in pure oxygen
flexible nature of this adhesive makes it useful for bonding and/or oxygen rich systems and should not be selected as
dissimilar substrates and for assemblies requiring bondline a sealant for chlorine or other strong oxidizing materials.
thickness up to one-tenth inch.
For safe handling information on this product, consult the
Features Material Safety Data Sheet, (MSDS).
High peel and high shear strength
Room temperature cure
Bonds variety of substrates Application
Long pot life Mixing Combine Part A and Part B in the correct ratio and mix
Excellent low temperature properties thoroughly. THIS IS IMPORTANT! Heat buildup during or after
mixing is normal. Do not mix quantities greater than ten pounds
(10 lb.), as excessive heat buildup can occur. Mixing smaller
Typical Uncured Part A Part B Mixed quantities will minimize the heat buildup.
Properties
Pot Life @ 77°F, 250 -- -- 50 Applying Bonding surfaces should be clean and dry. Hysol
grams mins
9430 can be applied with a spatula, brush or dispensing
Color Cream Clear Off White
Viscosity, cP 200,000 to 40 12,000
machine. Once the adhesive is dispensed, the bonded parts
400,000 should be held in contact until the part has developed handling
Specific Gravity 1.15 1.00 1.12 strength. Fixturing can be removed at this point. Since full bond
Mix Ratio strength has not yet been attained, load application should be
By weight 100 23 -- small at this time.
By volume 3.78 1 --
Density, lbs/Gal 9.64 8.35 9.3 Curing Hysol 9430 will cure to ultimate properties in 5 days at
room temperature. Curing temperatures up to 180°F can be
used to reduce cure time. For example, 1 hour at 180°F will give
Typical Properties Typical Value complete cure.
Tensile Strength, psi, ASTM D 638 5300
Modulus, psi, ASTM D 638 380,000 Cleanup It is important to remove excess adhesive from the
Elongation, %, ASTM D 638 6.0 work area and application equipment before it hardens.
Hardness, Shore D 75 Denatured alcohol and many common solvents are suitable for
removing uncured adhesive. Consult with your supplier’s
information pertaining to the safe and proper use of solvents.
Shear Strength, psi, ASTM D 1002 Etched Aluminum
Cure Schedule Test Temp oF Typical Value
o Storage
5 Days @ 77 F -67 5000 Store product in unopened container in a cool dry location. Ideal
77 4700 conditions are within the range 8 to 21 degrees C (46 to 70
140 1700 degrees F) and are recommended for long term storage.
180 750 Exposure to higher temperatures (greater than 28 degrees C)
for prolonged periods should be avoided as extended exposure
o
to warm conditions can adversely affect product properties. For
Shear Strength, ASTM D 1002 Cured 5 Days @ 77 F further specific shelf life information, contact your local Technical
Test Temp oF Typical Value, psi Service Center.
Degreased 77 3500
Aluminum
FRP 77 1400
Bonderized Steel 77 2400
Mineral Filled PET 77 850

30 Day Salt Spray 77 4000

30 Day @ 120 77 3700
o
F/100% RH

NOT FOR PRODUCT SPECIFICATIONS

THE TECHNICAL DATA CONTAINED HEREIN ARE INTENDED AS REFERENCE ONLY.
PLEASE CONTACT LOCTITE CORPORATION QUALITY DEPARTMENT FOR ASSISTANCE AND RECOMMENDATIONS ON SPECIFICATIONS FOR THIS PRODUCT.
ROCKY HILL, CT FAX: +1 (860)-571-5473 DUBLIN, IRELAND FAX: +353-(1)-451 - 9959
Loctite and Hysol are Trademarks of Loctite Corporation USA
 Hysol 9430 October 2001

Note
The data contained herein are furnished for information only and
are believed to be reliable. We cannot assume responsibility for
the results obtained by others over whose methods we have no
control. It is the user's responsibility to determine suitability for
the user's purpose of any production methods mentioned herein
and to adopt such precautions as may be advisable for the
protection of property and of persons against any hazards that
may be involved in the handling and use thereof. In light of the
foregoing, Loctite Corporation specifically disclaims all
warranties expressed or implied, including warranties of
merchantability or fitness for a particular purpose, arising
from sale or use of Loctite Corporation’s products. Loctite
Corporation specifically disclaims any liability for
consequential or incidental damages of any kind, including
lost profits. The discussion herein of various processes or
compositions is not to be interpreted as representation that they
are free from domination of patents owned by others or as a
license under any Loctite Corporation patents that may cover
such processes or compositions. We recommend that each
prospective user test his proposed application before repetitive
use, using this data as a guide. This product may be covered by
one or more United States or foreign patents or patent
applications.

Loctite and Hysol are Registered Trademarks of Loctite Corporation U.S.A.