Page 1 - Philips Bedside TV Installation Guide - SnapTV Products
NSSLGlobal Technologies AS
Philips Bedside TV Installation Guide
SW Version: 2.0
Date: 2021-04-16
Application Software installation
In order for this functionality to run, a package needs to be installed. This is normally done at the factory
before the SnapTV server is delivered.
Install this package on the SnapTV Server, the server where the Live TV channels are received and
formatted for Local Area Network distribution:
snaptv-philup
Application Software update
Application software can be updated offline. In order to do so, following steps should be performed:
• copy folder PhilipsSWUpdate to the SnapTV server
• run installation script:
cd PhilipsSWUpdate && sudo ./install.sh
Hospital TV Key and Screen Layout
Keys
Normally, the keys of the physical screen are used only. Hence, debug functionality is added by using the
remote control.
Keys which are in use (remote and screen):
CH- and CH+, used for prev/next channel.
Debug is turned on by the Yellow key (remote).
Keys available in debug mode
Key Functionality
Red
Green
Yellow Debug on
Blue
Left Refresh page / Debug off
2 Refresh page / Debug off
4 Log on (json info from TV)
5 Log off (json info from TV)
Page 2 - Philips Bedside TV Installation Guide - SnapTV Products
7 Log on (main log)
8 Log off (main log)
9 Clear logs
0 Get channel list in debug mode
Built in special key combinations
Function Key sequence
Pro settings 319753 MUTE
Reload app 179325
CSM menu 123654
Screen
Debug mode off
The channel list shall be visible when pressing channel up/down. The selected channel shall tune after a
two sec. timeout. The channel list is hidden after a 10 sec. timeout.
Debug mode on
Extra navigation keys and tuning status is shown
Setting up the TV
Enter Pro settings (319753 MUTE) Press "Meny for profesjonelle innstillinger"
• Set: Professional mode On
• Set: Professional Settings - Dashboard - Custom
• Set: Switch on settings - Switch On picture - WideScreen
• Set: Power Settings - Low Power Standby - Fast
• Set: Control settings - Subtitle On Startup - On
• Set: Dashboard Settings - Server URL - http://<IP>/ptv/
• Set: Installation - Multi remote control - <Any button to pair up RC with the TV>. Once the TV is set to
some value other than [Off] also the RC should be programmed to the same selection to still work
with the TV
Setting up the TV 58HFL6214U Model
Enter Pro settings (319753 MUTE, alternatively "mute left right up down ok")
• Set: Advanced - Professional Mode - On
• Set: Advanced - Power - Standby Mode - Fast
• Set: Dashboard - Select Dashboard - Custom Dashboard (Browser based) - Source - Server
• Set: Dashboard - Select Dashboard - Custom Dashboard (Browser based) - Source - Server Settings
- http://<IP>/ptv/
• Set: Switch On Settings - Picture Settings - Picture Format - Wide Screen
Page 3 - Philips Bedside TV Installation Guide - SnapTV Products
• Set: Swith On Settings - Subtitles - On
Programming the RC
Press and hold both the menu and the color button or digit button on the RC for about five seconds (You
should not point the RC to the receiver on the TV)
TV Hardware
• Philips 19HFL4010W/12
• Philips 19HFL5014W/12
TV Firmware
(Press "123654")
For Philips 19HFL4010W/12:
2.1 Current Main Software TPN141HE_004.002.075.128
2.2 Development SW Version TPM141HE_004.001.204.122
2.3 Standby SW 0.11
In case
Main Software < TPN141HE_004.002.075.128
Then:
• Copy the file autorun.upg to a USB pin and connect it to the TV set and follow the on-screen
instructions.
• However, the version TPN141HE_004.002.061.128 seems to be an equally good SW version.
For Philips 19HFL5014W/12:
2.1 Current Main Software TPM181HE_R.005.003.125.000
