User Manual

of

D
Advanced Kiddie Rides
ITE
LIM
（for Single-Support and Multi-Support Kiddy Rides）
G
IN
D
N

E-BIZ2CHINA LIMITED
VE

www.pandavending.com
A
D

Tel: 0086-21-52926646
N
PA

Fax: 0086-21-52950439

Please read this <User Manual> carefully before operating machines!

User Manual of Kiddie Rides

1
1. Technical Parameters:

Item Value Remark

Working Voltage AC220V (or on your request)

Machine Working Current ≤2.4A

Motor Power 180W

Rocking Frequency 0.58-0.75S

Carrying Capacity 40KGS

2. Applicability:
Place indoor, and apply to 3~7 years old children under 40Kgs.

D
3. Configuration and Operation:

ITE
1. Connect the machine to electrical outlet with plug.
2. LIM
Open the panel of control box with key, and turn on the electric switch on the
control box. Please make sure the indicial LED light inside the switch is shining.
G
3. Configure coin acceptor according to following instructions and picture –
IN

1) Open the panel of coin acceptor with key, and take out the coin acceptor.
2) Put the mode switch on N.O. (Normal Open).
D

3) Put the speed switch on MEDIUM (45ms medium pulse signal).

N

4) Mount a coin to be used into the coin holder according to the below picture.
VE

5) Adjust the sensitivity knob (it’s a small knob marked as “VR” on the coin acceptor), until
the coin acceptor can accept the right coins correctly, and reject other coins or tokens.
A

THIS STEP IS VERY IMPORTANT.

D

6) Close and lock up the panel.

N
PA

4. Configure the control box according to following instructions and picture-

1) Open the panel of control box with key.
2) Turn on the electric switch on the control box, and make sure the LED light is shining.
2
 3) Set the price from 1~3 coins by the “COUNT” knob.
4) Set the time from 1~3 minutes by the “TIMER” knob.
5) Adjust the volume by the “VOLUME” knob.
6) Switch off the machine for 10 seconds, and then restart the machine. THIS STEP IS
VERY IMPORTANT; OTHERWISE YOUR CONFIGURATION WILL NOT TAKE EFFECT.
7) Close and lock up the panel of control box.

D
ITE
LIM
5. After inserting coin (coins), the machine will give out alarm sound, and then rock with
G
IN

music according to the time set previously, and will give out alarm sound again 3
seconds before game over.
D
N

6. When suspend the operation of machine, please switch off the machine.
VE

4. Attentions:
A
D

1. Please make sure the ground line is connected well, when the machine is in use.
N

2. When machines can not work or stop automatically, please switch off the machine
PA

immediately and examine & repair the machine.

5. Maintenance:
1. When machine is dirty, you can lean it with cotton fabric.
2. In order to protect the machines, please lubricate the main moving parts of the
machine termly. You’d better lubricate the rocking shafts and bearings every 2
month, and lubricate other parts in every 6 months.
3. After a period of use, the straps or chains inside machines would get loose, and the
straps would possibly skid. At this time, please reposition the straps or chains inside
the machines.

3
6. Examine and Repair:
1. LED light is not shining, when turn on the electric switch on control box.

The LED light is not shining, means the PCB is NOT power-on. Please make sure
following things -
1) The electric switch is connected well and not broken.
2) The “Motor Fuse” and “Line Fuse” on the control box are not blown.
3) All plugs and wire lines related with PCB are good, and connected firmly and not
loose.

2. Motor cannot start-up, and machine cannot work.

1) Please check if the indicial LED light inside electric switch is shining or not.
2) Please check if “Motor Fuse” and “Line Fuse” on the control box are blown.
3) If the above is ok. Please take off the PCB from the machine and test on another
machine, to see if the PCB is good or broken.

D
i. If the PCB does not work on another machine, please change the CPU on the

ITE
PCB and try again. If still not works, we should change the whole PCB.
ii. If the PCB works on another machine, please go to the next step.
4) LIM
If all above no problem, but motors can not work, please examine the motor by this
way: pull out the plug of the motor, and connect the motor to AC220V power supply by
wire directly, to see if the motor works.
G
i. If the motor works correctly, please check all plugs and wire lines related with
IN

motor, and make sure they are all good, and connected firmly and not loose.
D

ii. If the motor cannot work, it means the motor is broken. Please change a new
N

motor.
VE
A
D
N
PA

4
3. No any sound from sound speaker.
1) Check if the “VOLUME” knob is on right position, and adjust it to see what happens.
2) Check if the sound speaker is damaged or broken.
3) Make sure all plugs and wire lines related with sound speaker is good and
connected firmly and not loose.
4) Please check if the PCB is ok, according to the way stated in 6-2-3.

4. Machine continually works by itself without coins.

1) Continually works by itself but without music.

a) Please change or just take off the capacitor (yellow color) from the PCB, and then
restart the machine.
b) If still problem, it means the relay (blue color) on the PCB is broken, and please
changes a new reply to test. Attached is a picture to show the capacitor and
relay.
2) Continually works by itself and with music. Please check if coin acceptor was jammed
by something or it's broken. Please change a new coin acceptor to try on the machine.

D
ITE
LIM
G
IN
D
N
VE
A
D

5. Straps skid.
N

After a long period use, the traps inside the machine will get loose or become slack.
PA

Please change the invalid straps on time.

--- Over ---