2012 Ford Pickup F150
2012 ENGINE Engine Cooling System - F-150
COOLANT PUMP - 3.5L GTDI, 3.7L
MATERIAL SPECIFICATIONS
Item Specification
Motorcraft® Orange Antifreeze/Coolant Concentrated
WSS-M97B44-D
VC-3-B (US); CVC-3-B2 (Canada)
Fig. 32: Exploded View Of Coolant Pump - 3.5L GTDI, 3.7L
Courtesy of FORD MOTOR CO.
Item Part Number Description
1 W503291 Coolant pump pulley bolt - 25 Nm (18 lb-ft) (4 required)
2 8A528 Coolant pump pulley
3 W503278 Coolant pump bolt (7 required)
4 8501 Coolant pump
5 8507 Coolant pump gasket (part of 8501)
6 8565 Coolant pump O-ring seal (part of 8501)
Removal
1. Remove the air cleaner outlet pipe. For additional information, REFER to INTAKE AIR
DISTRIBUTION & FILTERING .
2. Loosen the 4 coolant pump pulley bolts.
3. Remove the accessory drive belt. For additional information, REFER to ACCESSORY DRIVE .
NOTE: Cover the A/C compressor belt to prevent coolant contamination of the
belt.
miércoles, 27 de noviembre de 2024 8:15:52
8:15:46 Page 1 © 2011 Mitchell Repair Information Company, LLC.
2012 Ford Pickup F150
2012 ENGINE Engine Cooling System - F-150
4. Completely cover the A/C compressor belt with waterproof plastic.
5. Remove the thermostat housing. For additional information, refer to THERMOSTAT HOUSING -
3.5L GTDI or THERMOSTAT HOUSING - 3.7L .
6. Remove the 4 bolts and the coolant pump pulley.
7. Remove the 7 bolts and the coolant pump.
l Remove and discard the gasket and the O-ring seal in the coolant pump.
Installation
1. Install a new O-ring seal in the coolant pump and lubricate it with clean engine coolant.
2. Position a new gasket, press the coolant pump over the channel cover plate snout protruding from the
engine front cover and install the 7 bolts finger tight.
3. Tighten the coolant pump bolts in the sequence shown in 2 stages.
l Stage 1: Tighten to 10 Nm (89 lb-in).
l Stage 2: Tighten an additional 45 degrees.
Fig. 33: Identifying Coolant Pump Bolts Tightening Sequence
Courtesy of FORD MOTOR CO.
4. Position the coolant pump pulley and install the 4 bolts finger tight.
5. Install the thermostat housing. For additional information, refer to THERMOSTAT HOUSING -
3.5L GTDI or THERMOSTAT HOUSING - 3.7L .
6. Remove the plastic from the A/C compressor belt.
7. Install the accessory drive belt. For additional information, REFER to ACCESSORY DRIVE .
miércoles, 27 de noviembre de 2024 8:15:46 Page 2 © 2011 Mitchell Repair Information Company, LLC.
2012 Ford Pickup F150
2012 ENGINE Engine Cooling System - F-150
8. Tighten the 4 coolant pump pulley bolts.
l Tighten to 25 Nm (18 lb-ft).
9. Install the air cleaner outlet pipe. For additional information, REFER to INTAKE AIR
DISTRIBUTION & FILTERING .
10. Fill and bleed the cooling system. For additional information, refer to COOLING SYSTEM
DRAINING, FILLING AND BLEEDING .
miércoles, 27 de noviembre de 2024 8:15:46 Page 3 © 2011 Mitchell Repair Information Company, LLC.
