DRAFT SCHEDULE OF QTY.

Name of work :- Providing separate water supply scheme for Malookpur, Behdala,Jalgran (Tabba) in Tehsil Una(SH: Construction of pump house at Green
Avenue colony Jalgran) Job-1 Estimated cost #VALUE!
Earnest money Rs. 2,000.00
Time 3 months
Sl. Description of work Qty. Unit RATE AMOUNT
No. Figures Words
1.00 Excavation in foundation and trenches up to all depths and in all classification of earth work such as Pick 11.13 Cum Cum 225.00 #VALUE! 2504.00
work, Jumper work, chiselling or wedging out of soft and hard rock as blasting is prohibited, saturated soil
including bailing or pumping out of water, including cutting of bitumenous/concrete surface wherever
required, in all lifts including trimming and dressing of sides, levelling of beds to correct grade including
shoring, strutting , planking, timbering and dewatering where ever required. Stacking usable and unusable
material /soil seperataly and after laying, jointing and testing of pipes (for pipes, Pipe duct, chambers, x-
sings etc.), returning the usable soil in 15cm layers by ramming and watering and then disposing of all
surplus excavated soil/ unusable material as directed within all leads/ lifts and including cost of diversion for
traffic, night signal boards, fixing caution boards, crossing over trenches for access to houses, fencing etc.
complete in all respects within all leads and lifts as per direction of the Engineer-in-charge.

2.00 Providing and laying Cement Concrete [Link] ( 1 cement : 6 sand : 12 graded stone aggregate 40 mm 3.50 Cum Cum #VALUE! #VALUE! #VALUE!
nominal size) and curing complete excluding the cost of form work in foundation and plinth in all leads and
lifts and as per the direction of the .Engineer-in-Chaarge.
3.00 Ist class brick work using common burnt clay building bricks of appraoved quality in foundation and plinth in 3.38 Cum Cum #VALUE! #VALUE! #VALUE!
cement mortar 1:6 (1cement:6sand) in all leads and lift to the entire satisfaction of Engineer-in-charge.

4.00 Ist class brick work using common burnt clay building bricks of approved quality in super structure in cement 3.64 Cum Cum #VALUE! #VALUE! #VALUE!
mortar 1:6(1cement:6sand) in all leads and lift to the entire satisfaction of Engineer-in-charge.

5.00 Providing and fixing pressed steel doors frames manufactured from commercial mild steel sheet of 1.25 mm 38.40 Rmt. Rmt. #VALUE! #VALUE! #VALUE!
thickness including hinges, jump lock jamb, beed and if required angle threshold of mild steel angle of
section 50X25 mm or base ties of 1.25 mm pressed mild steel welded or regidly fixed together by
mechanical means, adjustable lugs with split and tails to each jamb including steel but things 2.5 mm thick
with gaurds, lock strike plate and shock as specified and applying a coat of approved steel primer after
pretreatment of the surface as directed by Engineer-in-charge.

6.00 Providing and laying cement concrete using M - 30 concrete mix (not less than 1:1.5:3) with graded stone 2.98 Cum Cum #VALUE! #VALUE! #VALUE!
aggregate 20 mm nominal size) and curing complete excluding the cost of form work and reinforcement for
reinforced concrete work in Suspended floor roofs, landing and shelves and their support balconies, beam
girderes bressumers and cantiliver. as directed by Engineer-in-charge.
7.00 Providing form work with steel plate 3.15 mm thick welded with angle iron frame 30x30x5mm so as give a
fair finish including centring, shuttering, strutting and propping etc with wooden battens and ballies, height of
propping and centring below supporting floor to ceiling upto any height and removal of the same for in site-
reinforced concrete and plain concrete work in
8.00 Flat surfaces such as soffits of suspended floors,roofs,landing and the like floor etc. up to 20 mm in 28.52 sqm sqm #VALUE! #VALUE! #VALUE!
thickness including all leads and lifts complete in all respect.
9.00 Providing Tor steel reinforcement for R.C.C. work including bending, binding and placing in position 278.00 kg kg #VALUE! #VALUE! #VALUE!
complete in all respect in all leads and lifts & as per direction of the Engineer-in-Charge
Total in Figures #VALUE!

Total in Words #VALUE!

TERMS AND CONDITIONS:-

1 The work will be carried out according to the Jalshakti vibhag specifications
2 Income tax, GST, security & labour cess as applicable will be deducted from the each bill of the contractor.
3 Nothing will be paid for rejected work.
4 The cement will be issued to the contractor from divisional store Malahat and recovery will be made @ Rs.300/-per bag & steel issued 6678/- per Qtl.
5 The empty bags of cement have to be returned to the Department otherwise the recovery will be made @ Rs 5/- per bag.
6 The contractor is fully responsible for watch and ward of the materials at site of work & nothing shall be paid extra for this purpose.

Page 1
 Sl. Description of work Qty. Unit RATE AMOUNT
No. Figures Words
DRAFT SCHEDULE OF QTY.
Name of work :- Providing separate water supply scheme for Malookpur, Behdala,Jalgran (Tabba) in Tehsil Una(SH: Construction of pump house and
internal electrical wiring of pump house at Green Avenue colony Jalgran) Job-2 Estimated cost #VALUE!
Earnest money Rs. 1,860.00
Time 3 months
Sl. Description of work Qty. Unit RATE AMOUNT
No. Figures Words
1.00 Providing and fixing, panelled glazed or panelled & glazed shutter for doors, windows & clearstory windows 11.58 sqm sqm #VALUE! #VALUE! #VALUE!
including bright finished black enamelled from butt hings with necessary screw in all leads and lift to the
entire satisfaction of Engineer-in-charge. 2nd class deodar wood 40mm thick.
2.00 Providing and fixing MS grill of required pattern in wooden frames / pressed steel frames of windows etc. 62.61 kg kg #VALUE! #VALUE! #VALUE!
with M.S. Flat square or rounded bar 12mm dia round headed bolts and nuts or by screws and or square
bars, ruled spacing to wooden frames windows and clearstory windows etc within all leads and lifts as per
direction of Engineer-in-charge.
3.00 Providing and laying cement concrete flooring [Link](1cement:2sand:4graded stone agg., 20mm nominal 18.00 sqm sqm #VALUE! #VALUE! #VALUE!
size) laid in one layer finished with a floating coat of neat cement within all leads and lifts as per direction of
Engineer-in-charge. 40mm thick
4.00 20 mm cement plaster in single coat on rough side of brick masonry for interior plastering upto floor two 51.60 sqm sqm #VALUE! #VALUE! #VALUE!
level including arrises, internal rounded angle, chamfers and or rounded angles not exceeding 80 mm in
girth and finished even and smooth with cement mortor 1:6 ( 1 cement :6 sand ) in all leads and lifts as per
the direction of the Enginner-in-Charge.
5.00 Pointing on brick work with cement mortor 1:3 (1cement : 3 sand) Raised and cut in all leads and lifts and as 38.62 sqm sqm #VALUE! #VALUE! #VALUE!
per the direction of the Engineer-in-Charge.
6.00 Providing plinth protection 50mm thick cement concrete [Link](1cement:3asand:6graded stone agg., 40mm 13.59 sqm sqm #VALUE! #VALUE! #VALUE!
nominal size) including finishing the top surface concrete smooth within all leads and lifts as per direction of
Engineer-in-charge.
7.00 Applying priming coat on new wood and wood based surfaces after and including preparing the surface by 26.06 sqm sqm #VALUE! #VALUE! #VALUE!
thoroughly cleaning oil,greese,dirt and other foreign matters,sand papering and [Link] mixed paint
brushing wood primer pink in all leads and lifts and as per the direction of the Engineer-in-Charge.

8.00 Painting two coats (excluding priming coat) on new wood and wood based surfaces,with enamel paint to 26.06 sqm sqm #VALUE! #VALUE! #VALUE!
give an even shade including cleaningthe surface of dirt ,dust and other foreign matters sand papering and
stopping with enamel paint other than white in all leads and lifts and as per the direction of the Engineer-in-
Charge.
9.00 White washing with lime on undecorated wall surfaces two coats to give an even shade including thoroughly 51.60 sqm sqm #VALUE! #VALUE! #VALUE!
brooming the surface to remove all dirt , dust and other foreign matters in all leads and lifts and as per the
direction of the Engineer-in-Charge.
10.00 Hirmachi colour wash on undecorated wall surfaces (Three coats) to give an even shade including 51.60 sqm sqm #VALUE! #VALUE! #VALUE!
thoroughly brooming the surfaces to remove all dirt,dust, mortar drops and other foreign matter complete in
in all respect as per the direction of the Engineer-in-Charge.
11.00 Providing and fixing anodised M.S. sliding door bolts with bolts and nuts screws etc in all leads and lifts and
as per the direction of the Engineer-in-Charge.
250x16mm 3.00 Nos. Each #VALUE! #VALUE! #VALUE!

12.00 Providing and fixing anodised MS tower bolts ( barrel type) with screws etc. in all leads and lifts and as per
the direction of the Engineer-in-Charge
200x10m 6.00 Nos. Each #VALUE! #VALUE! #VALUE!

150x10mm 10.00 Nos. Each #VALUE! #VALUE! #VALUE!

13.00 Providing ad fixing anodised MS handles with necessary screws etc. in all leads and lifts and as per the 14.00 Nos. Each #VALUE! #VALUE! #VALUE!
direction of the Engineer-in-Charge. 125 mm
14.00 P/F MS fan clamps type 1 of 16 mm dia bar bent to shape with hooked ends in RCC slab during laying 1.00 Nos. Each #VALUE! #VALUE! #VALUE!
including painting the exposed portion of roof as per standard design complete within all lead and lifts as per
the direction of the Engineer-in-Charge..

15.00 Wiring for light/Fan point/Exhaust fan point/call bell point with 1.5 [Link] PVC insulated copper conductor 5.00 Nos. Each 592.00 #VALUE! 2960.00
cable in surface/recessed PVC conduct at required including carriage of all material within all leads and lifts.
Group "C"

Page 2
 Sl. Description of work Qty. Unit RATE AMOUNT
No. Figures Words
16.00 Wiring for light/power plug with 2 x 4 [Link] PVC insulated copper conductor or single core cable in 20.00 Mtrs [Link] 148.00 #VALUE! 2960.00
surface/recessed steel conduit alongwith 1 No. 2.24 mm dia bare copper wire for loop earthing as required
including carriage of materials within all leads and lifts.

17.00 Wiring for circuit wiring with 2 x 1.5 [Link] PVC insulated copper conductor single core cable in 15.00 Mtrs [Link] 96.00 #VALUE! 1440.00
surface/recessed steel conduit as required including carriage of material within all leads and lifts.

18.00 Wiring for sub-main wiring with the following size of copper conductor single core cable in surface/recessed 2.00 Mtrs [Link] 199.00 #VALUE! 398.00
steel conduit as required including carriage of materials upto all leads and lifts. 2x6 [Link]

19.00 Supplying and fixing metal box of 180 x 100 x 60mm deep (Nominal size) on surface/recess with suitable 1.00 No. Each 136.00 #VALUE! 136.00
size phonolic leminated sheet cover fixing 3 pim 15/16 amps socket tumber/piano type switch connections
painting etc. including carriage of materials within all leads and lifts.
20.00 Supplying and fixing backellite batten/angle holder including connection as required. 3.00 Nos. Each 32.00 #VALUE! 96.00

21.00 Providing, installing, testing and commissioning of ceiling fan and regulator including wiring the rod of 1.00 No. Each 1548.00 #VALUE! 1548.00
standard length (upto 30cm) with 1.5 Sqmm PVC insulated copper conductor single core cabe etc. as
required sweep type. Cat. A
22.00 Providing, installation, testing and commissioning of prewired flourscent tube fitting complete with ballast, 1.00 No. Each 759.00 #VALUE! 759.00
starter and capactors but excluding flourscent tube rod, suitable to operate on 230 volts single phase
[Link] directly on surface with copper wiring as required including carriage of materials within all leads
and lifts tube fixture 1 x 36 watt Box type Category "A".
23.00 Supplying and fixing 40Amps to 63 Amps rating 240 Volts "L" series miniature circuit breaker of following 1.00 Nos. Each 652.00 #VALUE! 652.00
poles in the existing MCB DB complete with connections, testing and commissioning etc. as required
including carriage of material within all leads and lifts. Category- A, 63 Amps.
24.00 Supplying and fixing of following way single pole and neutral sheet steel MCB distribution board 240 volts on 1.00 No. Each 899.00 #VALUE! 899.00
surface/recessed completed with tinned, copper busher neutral link, earth bar, detachable gland plate inter -
connections, including painting, earthing etc. as required Bus bar 8 way.

25.00 Supplying and fixing 5 Amps to 32 Amps rating 240 volts, G series miniature circuit breaker of following 3.00 Nos. Each 153.00 #VALUE! 459.00
poles in the existing MCB, DB complete with connections testing and commissioning etc. as required
Category "A", single pole.

26.00 Earthing with G.I. pipe earth, pipe 4.5 mtrs length, 40mm dia including accessories and providing masonry 1.00 Set Set 2679.00 #VALUE! 2679.00
enclousres with cover plate having locking arrangement and watering pipe etc.( but without charcal coke
and salt) complete as required including carriage of materials within all leads and lifts.

27.00 Extra using salt and charcoal for pipe earth electrode as required, including carriage of materials within 1.00 Set Set 904.00 #VALUE! 904.00
all leads and lifts.

28.00 Supplying and laying 6 Sqmm [Link] at 0.50 mtr below ground level for conductor earth electrode, 20.00 Rmt [Link] 24.00 #VALUE! 480.00
including soldering etc. as required including carriage of materials within all leads and lifts.

29.00 Providing, fixing & testing Street Light Fixture with CFL of 36 watt, copper ballast, G.I. Pipe bracket, 1.00 No. Each 1500.00 #VALUE! 1500.00
complete in all respects.

Total in Figures #VALUE!

Total in Words #VALUE!

TERMS AND CONDITIONS:-

1 The work will be carried out according to the Jalshakti vibhag specifications
2 Income tax, GST, security & labour cess as applicable will be deducted from the each bill of the contractor.
3 Nothing will be paid for rejected work.
4 The cement will be issued to the contractor from divisional store Malahat and recovery will be made @ Rs.300/-per bag & steel issued 6678/- per Qtl.
5 The empty bags of cement have to be returned to the Department otherwise the recovery will be made @ Rs 5/- per bag.
6 The contractor is fully responsible for watch and ward of the materials at site of work & nothing shall be paid extra for this purpose.

Page 3
 Sl. Description of work Qty. Unit RATE AMOUNT
No. Figures Words
DRAFT SCHEDULE OF QTY.
Name of work :- Providing separate water supply scheme for Malookpur, Behdala,Jalgran (Tabba) in Tehsil Una(SH: Laying, jointing and testing of GMS
pipe in Rising Mains at Green Avnue colony water supply scheme Jalgran) Estimated cost #VALUE!
Earnest money Rs. 1,460.00
Time 1 month
Sl. Description of work Qty. Unit RATE AMOUNT
No. Figures Words
1.00 Excavation in foundation and trenches up to all depths and in all classification of earth work such as Pick 214.92 Cum Cum 225.00 #VALUE! 48357.00
work, Jumper work, chiselling or wedging out of soft and hard rock as blasting is prohibited, saturated soil
including bailing or pumping out of water, including cutting of bitumenous/concrete surface wherever
required, in all lifts including trimming and dressing of sides, levelling of beds to correct grade including
shoring, strutting , planking, timbering and dewatering where ever required. Stacking usable and unusable
material /soil seperataly and after laying, jointing and testing of pipes (for pipes, Pipe duct, chambers, x-
sings etc.), returning the usable soil in 15cm layers by ramming and watering and then disposing of all
surplus excavated soil/ unusable material as directed within all leads/ lifts and including cost of diversion for
traffic, night signal boards, fixing caution boards, crossing over trenches for access to houses, fencing etc.
complete in all respects within all leads and lifts as per direction of the Engineer-in-charge.

2.00 Laying,Jointing and Testing in trenches Galvanized mild steel flanged/butt welded pipe of below mentioned
dia and grade conforming to IS 1239-2004 (with latest ammendments The M.S. flanges are to be provided
1% of total joints as per table below conforming to 6392-1971 ( Latest uptodate ammendments) and welding
of M.S. flanges with pipe as per IS: 816-1965 with electrode as per IS: 814-1967 including required Nos.
and size of M.S. nuts and bolts as per IS: 1369-1967 and compressed asbestos fibre jointing gaskets sheet
not less than 3mm thick as per IS: 27121-1965. The welding of flanges to be done on both faces in three
layers in each face to make the joints leak proof including all kind of specials such as bends of all degree to
be made from parent tube, short pieces, tail pieces all made from parent tube and to the entire satisfaction
of enginer-in-charge. The pipes end should be bevelled suitable for butt welding. The circumferencial butt
welded joints ( 99% of the total joints) by electrical arc welding to following dia & class pipes,welding of
pipes to be done in three layers to make the joints leak proof and to achieve the minimum effective throat
thickness of weld conforming to IS- 816-1969 specifications, by using welding electrodes of 2.5 mm to 6.3
mm of Advani oerlikon (Adore)-CITOJET/ESAB make, conforming to IS 814-1991, at site of work complete
in all respects and including DPT test for joints & manual/mechnical handing of pipes. The laying of pipe
shall confirm to BIS-5822 (with latest ammendments uptodate), including all kind of specials such as bends
of all degree to be made from parent tube, short pieces, tail pieces all made from parent tube within all leads
and lifts. ( Earth work in trenches, M.S. flanges and butt welded joints to be measured and paid for
separately)

125mm dia GMS (M) IS 1239-2004 300.00 Rmt Rmt #VALUE! #VALUE! #VALUE!

3.00 Providing and welding M.S. flanges @1% at suitable point, conforming to following tables as per IS: 6392-
1971 (Latest with upto date amendments) with plain end GMS/MSERW pipe in requsite number of layers on
both faces to make the joint leak proof (The cost of providing and laying of MSERW pipes to be measured
and paid for seprately). The welding of flanges should conform to IS:816-1969 with electrodes as per IS:
814-1991 and required number of nuts and bolts conforming to IS 1364. including cost of gasket sheet nuts
& bolts. The thickness of gasket sheet not less then 3.00 mm conforming to IS 2712-1998. The work shall
be done to the entire satifaction of engineer in charge with in all leads and [Link] of Engineer-in-Charge.

125mm dia T-17 1.00 Pair Pair #VALUE! #VALUE! #VALUE!

5.00 Providing circumferential butt welded joints @99% by electrical arc welding to GMS pipe, welded in
requisite number of weld runs so as to achieve the minimum effective throat thickness of weld conforming to
IS 816-1969 specifications, by using welding electrodes of 2.5mm to 6.3mm of Advani Oerilikon (Adore)-
CITOJET/ES/ESAB make,conforming to IS 814-1991, include Die pentration test,at site of work complete in
all respects, including manual/mechanical handling of pipes in all leads and lifts to the entire satisfaction of
Engineer-in-Charge.

125mm dia 49.00 Joints Joint #VALUE! #VALUE! #VALUE!

Total in Figures #VALUE!

Total in Words #VALUE!

Page 4
 Sl. Description of work Qty. Unit RATE AMOUNT
No. Figures Words
TERMS AND CONDITIONS:-
1 The work will be carried out according to the Jalshakti vibhag specifications
2 Income tax, GST, security & labour cess as applicable will be deducted from the each bill of the contractor.
3 Nothing will be paid for rejected work.
4 The GMS will be issued free of cost to the contractor at divisional store Malahat .
6 The contractor is fully responsible for watch and ward of the materials at site of work & nothing shall be paid extra for this purpose.

REVISED SCHEDULE OF QTY.

Name of work :- Providing separate water supply scheme for Malookpur, Behdala,Jalgran (Tabba) in Tehsil Una(SH;-Construction of OHSR 3,50,000 ltrs Tendered amount. Rs. 2,446,707.00
cap with 25 mts staging height at Jalgran (Green Avenue) Estimated cost
Earnest money Rs. 1,460.00
Time 1 month
Sl. Description of work Qty. Unit RATE AMOUNT
No. Figures Words
1.00 Excavation in foundations, trenches etc., in earth work. In all kind of soil such as spade work, pick work, 194.98 cum cum 205.00 #VALUE! 39971.00
jumper work, blasting work in soft and hard rock chiselling / wedging out of rock where blasting is
prohibited and in saturated soil etc. in all leads and lifts, stacking the excavated soil not more than 3 metres
clear from the edge of excavation and then returning the stacked soil in fifteen centimetre layers,when
required into plinths sides of foundations etc. consolidating each deposited layer by ramming and
dewatering and then disposing of all surplus excavated earth as directed within all leads and lifts as per
direction of the Engineer-in-Charge.
2.00 Providing and laying cement concrete 1: 3 :6 ( 1 cement :3 sand :6 graded stone aggregate 20 mm nominal 7.50 cum cum 4000.00 #VALUE! 30000.00
size) and curing complete excluding the cost of form work in foundation and plinth in all leads and lifts and
as per the direction of the Engineer-in-Charge.

3.00 Providing and laying cement concrete M-30 (not leaner than 1:1.5:3) mix concrete using crushed stone
aggregate 20 mm nominal size ) and curing complete excluding the cost of form work and reingorcement
for reinforced concrete work in:

3.01 Foundation, footing bases of columns and the like and mass concrete. 31.66 cum cum 6000.00 #VALUE! 189960.00

3.02 Columns pillars,post and struts. 33.00 cum cum 6300.00 #VALUE! 207900.00

3.03 Lintels, beams,girders,bressumer and cantilever. 32.78 cum cum 6300.00 #VALUE! 206514.00

3.04 Stair case(except spiral stair case)excluding landing but including preparing of the surface and finishing of 7.42 cum cum 6300.00 #VALUE! 46746.00
nosing.

3.05 Arches upto all heights. 11.23 cum cum 6400.00 #VALUE! 71872.00

3.06 Suspended floor roofs, landing and shelves and their support balconies, beam girderes bressumers and 3.65 cum cum 6300.00 #VALUE! 22995.00
cantiliver.

3.07 Wall ( any thickness but not less than 0.10 mtrs thickness attached pilasters butteress, plinth and string 23.14 cum cum 6400.00 #VALUE! 148096.00
courses etc. from top of foundation level.

Page 5
Sl. Description of work Qty. Unit RATE AMOUNT
No. Figures Words
4.00 Providing form work with steel plates 3.15 mm thick welded with angle iron in frame 30 x 30 x 5 mm, so as
to give a fair finish including centring , shuttering, strutting and propping etc with wooden battans and
ballies height of propping and centring below supporting floor to ceiling not exceeding 4 mtrs. and removal
of the same for insitu-reinforced concrete and plain concrete work in all leads and lifts & as per the direction
of the Engineer-in-Charge.

4.01 Foundation , footings , basis of columns etc. and mass concrete. 39.78 sqm sqm 200.00 #VALUE! 7956.00

4.02 Columns,pillars posts,struts circular or curved in plan. 264.00 sqm sqm 600.00 #VALUE! 158400.00

4.03 Sides and soffits of beams,beam haunching , cantiliver,bressumers & lintle not exceeding 1.00 mtr. Depth in 221.83 sqm sqm 600.00 #VALUE! 133098.00
all height. of floors.

4.04 Vertical surfaces such as wall of (any thickness), partitions and the like inculding attached 231.41 sqm sqm 600.00 #VALUE! 138846.00
pillasters,buttresses, plinth and string courses and the like..

4.05 Sloping or battering surface i/c folded plates where inclination to horizontal plan exceed 30 deg (where 67.29 sqm sqm 1400.00 #VALUE! 94206.00
shuttering may be provided both on underside and upperside if reqd only the area of under side shall be
measured for payment)

4.06 Flat surfaces such as soffits of suspended floors, roofs, landings and the [Link] 200 mm thickness. 49.99 sqm sqm 600.00 #VALUE! 29994.00

4.07 Stair cases with slopping or stepped soffits excluding landings. 66.76 sqm sqm 600.00 #VALUE! 40056.00

5.00 Providing of form work of ordinary timber planking so as to give a rough finish including centering, shuttering 189.39 sqm sqm 2400.00 #VALUE! 454536.00
, strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding
6 mtrs. and removal of the same insitu reinforced concrete and plain concrete work in all leads and lifts and
as per the direction of the Engineer- in - Charge in Arches not exceeding 6 mtrs span.

6.00 Steel work welded in built up section , trusses and framed work i/c cutting hoisting fixing in position and 8.41 Qtl Qtl 9600.00 #VALUE! 80736.00
applying a priming coat of red lead paint in gretings, framed guards, bors ladders railing brackets and
similar works.
7.00 Placing of Tor steel reinforcement for R.C.C. work including bending, binding and placing in position 14373.79 Kg Kg 15.00 #VALUE! 215607.00
complete in all respect in all leads and lifts & as per direction of the Engineer-in-Charge floor two level.

8.00 Providing plinth protection 50 mm thick in cement concrete 1: 3: 6 (1cement : 3 sand : 6 graded stone 94.02 sqm sqm 220.00 #VALUE! 20684.00
aggregate 20 mm nominal size ) including entire carriage of material and as per direction of the Engineer-
in-Charge.
9.00 Providing under layer for plinth protection of 75 mm thick ( unconsolidated )bed dry brick/ stone 94.02 sqm sqm 220.00 #VALUE! 20684.00
aggregaated 40 mm nominal size will rammed and consolidated and grouted with fine sand including
preparation of ground.
10.00 Providing and fixing MS manhole cover of 500 mm dia with frame ( medium grade duty ) weight of cover 1.00 No. Each 2500.00 #VALUE! 2500.00
and frame to be not less than 23 kg.

11.00 Fixing inlet, outlet, over flow and Scour pipe of GMS pipe of following internal dia ( medium grade)i/c extra
carriage within all leads and lifts and as per the direction of the Engineer-in-Charge.

11.01 Inlet R/main 150 mm. 30.00 Rmt Rmt 65.00 #VALUE! 1950.00

11.02 Outlet R/main 100 mm. 30.00 Rmt Rmt 55.00 #VALUE! 1650.00

11.03 Over flow & scour pipe 80 mm dia 30.00 Rmt Rmt 45.00 #VALUE! 1350.00

12.00 Providing ,fixing and welding of MS flanges conforming to IS code 6392-1971 table 5 of below noted
diameter ( Latest with upto date ammendments ) welding of M.S. flanges on G.I. pipe on both ends
according to relevent BIS standard and detailed technical specification ) and provided with nuts,bolts of
required size complete in all respect and as per diection of the Engineer-in-Charge.
12.01 Inlet R/main 150 mm. 8.00 Pair Pair 1550.00 #VALUE! 12400.00

Page 6
 Sl. Description of work Qty. Unit RATE AMOUNT
No. Figures Words
12.02 Out let pipe 100 mm ( Distribution ) 7.00 Pair Pair 1400.00 #VALUE! 9800.00

12.03 Over flow & scour pipe 80 mm dia 8.00 Pair Pair 1150.00 #VALUE! 9200.00

13.00 Providing and fixing [Link] valve ( With hand whell ) as per IS 780 class for following dia ( including brass
spindle and as per IS 2906 class-II including MS Flange, bolts, nuts, rubber insertion etc. complete in all
respect i/c carriage of material within all leads and lifts.
13.01 Out let pipe 100 mm ( Distribution ) 1.00 No. Each 10000.00 #VALUE! 10000.00

13.02 Scour pipe 80 mm 1.00 No. Each 9000.00 #VALUE! 9000.00

14.00 P/F of water measuring gauge of standard design complete in all respect. 3.00 Job Job 3500.00 #VALUE! 10500.00

15.00 Providing and fixing sky lightening arrestot complete in all respect in all leads and lifts i/c carriage as per the 3.00 Job Job 4000.00 #VALUE! 12000.00
direction of the Engineer-in-Charge.
16.00 Providing and fixing vent opening including cowl with mesh in the top of the tank i/c carriage all leads and 3.00 Job Job 2500.00 #VALUE! 7500.00
lifts and as per the direction of the Engineer-in-charge.

Total in Figures 2446707.00

Total in Words #VALUE!

Executive Engineer,
Jalshakti Division No.1 Una

Page 7
Please Enable Macros to View BoQ information
Q information
 ABSTRACT OF QTY
Name of Work: Providing Separate Water Supply Scheme to PGI SATELLITE CENTRE UNA at Malahat in Tehsil and District UNA (HP). (SH:- Providing, laying, jointing and
testing of GMSERW / GMS pipe in Rising Mains, Supply & Errection of Pumping Machinery and Construction of civil work)

Sl. Description of work Unit P/L of C/O P/H C/O C/O Single room P/H C/O coll. C/O 2 No. Storage tank Total Qty
No. R/main cum att. Boundary Toilet Tank 2.0 3,50,000 ltrs each.
room wall lakh ltrs
cap
1 2 3 4 5 6 7 8 9 10 11
1.00 Excavation in foundation and trenches Cum 6273.45 39.64 42.87 6.91 10.19 x 2= 20.38 88.02 114.04 x 2= 228.08 6699.35

92.00 Providing, laying cement concrete [Link] (40mm Cum 17.65 10.72 0.65 3.9 x 2= 7.8 36.82
nominal size) in foundation and plinths.

93.00 Providing, laying cement concrete [Link] (20mm Cum 9.86 12.87 x 2= 25.74 35.60
nominal size) in foundation and plinths.

94.00 Ist class brick work using common burnt clay Cum 9.38 30.35 3.12 9.37 x 2= 18.74 61.59
building bricks in foundation and plinth in cement
mortar 1:6
95.00 Ist class brick work using common burnt clay Cum 29.32 1.15 5.95 x 2= 11.90 42.37
building bricks of approved quality in super
structure in cement mortar 1:6
96.00 Half brick work using common burnt clay building Sqm 40.08 120.84 160.92
bricks in super structure in cement mortar 1 : 4

97.00 Boulder filling under floor dry hand packed tightly in Cum 18.30 18.30
foundation and plinths.

98.00 Providing form work with steel plates work in:- 0.00

98.01 Foundation, footing and bases of columns Sqm 37.10 37.10

98.02 i) Square, rectangular or polygonal in plan Sqm 61.32 61.32

98.03 ii) Circular in plan Sqm 39.56 39.56

98.04 Beams,cantilivers,girders and lintels sides and Sqm 139.93 9.41 x 2= 18.82 158.75
soffits of beams,beam haunchings, cantilivers ,
girders, bressumers
98.05 Flat surfaces such as soffits,suspended floors,roofs Sqm 29.36 5.87 13.5 x 2= 27 62.23
landing

98.06 Edges of slab and breaks in floors and walls under Rmt 16.70 16.70
20 cm wide.

98.07 vertical wall Sqm 212.20 315.63 x 2= 631.26 843.46

99.00 Providing of form work of ordinary timber planking Sqm 63.48 84.64 x 2= 169.28 232.76
in arches

100.00 P/L C.C. 1:1.5:3 ( 20 mm nominal size ) in :-

100.01 Suspended floors, roofs, Cum 0.73 4.29 x 2= 8.58 1.69 1.94 x 2= 3.88 14.88

100.02 -do- foundation Cum 13.15 17.15 x 2= 34.3 47.45

100.03 -do- walls Cum 21.22 31.56 x 2= 63.12 84.34

100.04 do- arches Cum 6.35 8.46 x 2= 16.92 23.27

101.00 Providing and laying cement concrete [Link] ( 20 0.00

mm nominal size ) work in:-

101.01 Foundation footings bases of columns Cum 8.15 8.15

101.02 i) Square or rectangalar in Plan Cum 10.51 10.51

101.03 ii) Circular in plan Cum 6.08 6.08

101.04 Suspended floors, roofs,landings and shelves and Cum 19.15 19.15
their supports, balconies, beams, girders,
bressumers
102.00 Providing tor steel reinforcement for RCC work Kg 3705.60 65.89 385.96 x 2= 771.92 3668.4 5148.90 x 2= 10297.8 18509.61

103.01 Providing and fixing pressed steel doors frames Rmt 141.65 14.9 x 2= 29.8 171.45
Profile A

103.02 -do- Profile B Rmt 9.7 x 2= 19.4 19.40

104.00 Providing and fixing panneled glazed or panelled Sqm 36.04 5.01 x 2= 10.02 46.06
and glazed shutters for doors, windows 40 mm
thick 2nd class deodar wood.
105.00 Providing & fixing M.S. grills Kg 161.45 5.65 27.23 x 2= 54.46 221.56

106.00 Cement concrete flooring [Link] , Sqm 26.77 1.57 13.5 x 2= 27 55.34

107.00 6mm cement plaster to ceiling in CM 1:3 Sqm 18.90 6.95 25.85

108.00 15 mm cement plaster in single coat on rough side Sqm 393.40 164.14 26.74 45 x 2= 90 674.28
of brick/concrete stone walls cement mortar 1:6

109.00 Pointing on brick work with cement mortor 1:3 Sqm 264.25 174.95 50.91 x 2= 101.82 541.02

110.00 RCC smooth finishing Sqm 212.20 315.63 x 2= 631.26 843.46

111.00 White washing with lime on undecorated wall Sqm 18.90 45.00 x 2= 90 108.90

112.00 Hirmachi colour wash on undecorated wall surfaces Sqm 45.00 x 2= 90 90.00

113.00 Distempering with dry distemper of approved brand Sqm 393.40 393.40
 1 2 3 4 5 6 7 8 9 10 11
114.00 Applying priming coat on new wood and wood Sqm 81.09 11.28 x 2= 22.56 103.65
based surfaces

115.00 Painting two coats (excluding priming coat) on new Sqm 81.09 11.28 x 2= 22.56 103.65
wood and wood based surfaces

116.00 Applying priming coat over new steel Sqm 3.966 3.97

117.00 Painting two coats on new steel Sqm 11.34 3.966 15.31

118.01 Providing and fixing anodised MS sliding door bolts Each 5.00 5.00
300x16 mm

118.02 -do-250x16 Each 1 2 x 2= 4 5.00

119.00 Providing and fixing anodised MS tower bolts

119.01 200x16 mm Each 10.00 10.00

119.02 250x10 mm Each 2 2 x 2= 4 6.00

119.03 150 x 10 mm Each 33.00 10 x 2= 20 53.00

120.00 Providing ad fixing anodised MS handles 125 mm Each 47.00 2 14 x 2= 28 77.00

121.00 Providing and fixing MS Hooks 250 mm. Each 54.00 54.00

122.00 Providing plinth protection 50mm thick cement Sqm 25.29 14.88 x 2= 29.76 55.05
concrete [Link]

123.00 Proving under layer for plinth protection of 75 mm Sqm 33.72 33.72
thick

124.00 White glazed tiles 6 mm thick in flooring cement Sqm 2.65 2.65
mortar 1:3

125.00 White glazed tiles 6 mm thick in Skirting Sqm 9.87 9.87

126.00 Steel work welded in built up sections,trusses and Kg 5231.74 104.1 15.75 69.79 90.82 x 2= 181.64 5603.02
framed work In trusses and trussed purlings

127.00 Providing & fixing 0.60 mm thick prepainted steel Sqm 166.44 166.44
sheet

128.00 Providing ridges or hips 60cm over all in plinth with Rmt 42.10 42.10
galvanised iron G.I. sheet

129.00 Providing valley 90cm over all in plain G.I. sheets Rmt 13.60 13.60
fixed with galvanised iron J or L hooks

130.00 Excavation in earth work and filling in 15 cm. layers Cum 40.21 40.21
in foundation & plinths

131.00 Finishing wall with water proofing cement paint Sqm 339.09 33.69 372.78

132.00 Providing and laying Damp proof course 38 mm Sqm 1.45 1.45
thick cement concrete [Link]

133.00 Applying a coat of hot bitumen ( Mexphalt 80/100 of Sqm 1.45 1.45
equivalent ) using 1.70 Kg/sqmtrs.

134.00 P/F of angle iron door, window, clerestory windows Rmt 7.05 7.05
manufactured from MS angle iron section of
40x40x6mm thicknes

135.00 P/F of 1 mm thick MS Sheet garage door with Sqm 1.46 1.46
frame of 40x40x6mm angle iron 3.15 mm gusset
plates
136.00 Providing 40x3mm flat iron hold fast Each 6 20 x 2= 40 46.00

137.00 Providing / fixing vitreous china water closet Each 1 1.00

squatting pan ( Indian type WC pan ) size 580
mm
138.00 Providing / fixing of PVC "P" Trap complete in all Each 1 1.00
respect.

139.00 Providing / fixing of PVC bend 50 mm dia complete Each 2 2.00

in all respect.

140.00 Providing / fixing of PVC waste pipe and ventilating Rmt. 1.8 1.80
pipes complete in all respect.
100 mm dia
141.00 -do- 50 mm dia Rmt. 3 3.00

142.00 Providing / fixing of wall ceiling and floor Rmt. 10 10.00

galvanized MS tube (Light) tube fitting

143.00 Providing / fixing of CP brass bib cock with Rmt. 1 1.00

capstan head 15 mm dia complete in all respect.

144.00 Providing / fixing of CC Hume pipes each 750 mm Each 4 4.00

dia 1200 mm long

145.00 Providing / fixing of 10.00/12.50/15.00 litres Each 1 1.00

vitreous china low level flushing cistern.

146.00 P/F MS fan clamps type 1 of 16 mm dia bar Each 1 x 2= 2 2.00

147.00 laying in trenches GMS/MS Tubes (L/M class) tube Rmt 21 21 x 2= 42 63.00
fitting 100mm dia

148.00 Providing and fixing [Link] valve 100mm dia Each 3 3 x 2= 6 9.00

149.00 Constructing chamber for sluice valve, with CI Each 2 2 x 2= 4 6.00

surface box 100 mm top dia.,160 mm bottom dia. &
180 mm deep.

150.00 Prov. & fixing SFRC Man hole cover Each 2 2 x 2= 4 6.00
 1 2 3 4 5 6 7 8 9 10 11
151.00 Wiring for light/Fan point/Exhaust fan point/call bell Point 25 5 x 2= 10 35.00
point with 1.5 [Link] Group "C"

152.00 Wiring for light/power plug with 2 x 4 [Link] PVC Rmt 150 20 x 2= 40 190.00
insulated copper conductor or single core cable

153.00 Wiring for circuit wiring with 2 x 2.5 [Link] PVC Rmt 100 15 x 2= 30 130.00
insulated copper conductor single core cable

154.00 Wiring for sub-main wiring . 2x6 [Link] Rmt 20 2 x 2= 4 24.00

155.00 Supplying and fixing metal box of 180 x 100 x Each 5 5.00
60mm deep (Nominal size) fixing 3 pin 15/16 amps
socket

156.00 Supplying and fixing metal box of 180 x 100 x Each 1 x 2= 2 2.00
60mm deep (Nominal size) fixing 3 pin 5/6 amps
socket

157.00 Supplying and fixing backellite batten/angle holder Each 15 3 x 2= 6 21.00

including connection as required.

158.01 Providing, installing, testing and commissioning of Each 1 1.00

ceiling fan and regulator Cat. A

158.02 Providing, installing, testing and commissioning of Each 1 x 2= 2 2.00

ceiling fan and regulator Cat. B

159.00 Providing, installation, testing and commissioning of Each 1 1 x 2= 2 3.00

prewired flourscent tube fitting complete 1 x 36
watt Box type Category "A".

160.00 Supplying and fixing 40 Amps to 63 Amps rating Each 2 1 x 2= 2 4.00

240 Volts "L" series miniature circuit breaker of
following poles in the existing MCB DB complete
with connections, testing and commissioning etc. as
required including carriage of material within all
161.01 Supplying and fixing of following way single pole Each 2 2.00
and neutral sheet steel MCB distribution board 240
volts on surface/recessed completed with tinned,
copper busher neutral link, earth bar, detachable
gland plate inter -connections, including painting,
161.02 Supplying and fixing of following way single pole Each 1 x 2= 2 2.00
and neutral sheet steel MCB distribution board 240
volts on surface/recessed completed with tinned,
copper busher neutral link, earth bar, detachable
gland plate inter -connections, including painting,
162.00 Supplying and fixing 5 Amps to 32 Amps rating 240 Each 2 3 x 2= 6 8.00
volts, G series miniature circuit breaker of following
poles in the existing MCB, DB complete with
connections testing and commissioning etc. as
required Category "A", single pole.
163.00 Earthing with G.I. pipe earth, pipe 4.5 mtrs length, Set. 1 1 x 2= 2 3.00
40mm dia including accessories and providing
masonry enclousres with cover plate having locking
arrangement and watering pipe etc.( but without
charcal coke and salt) complete as required
164.00 Extra using salt and charcoal for pipe earth Set. 1 1 x 2= 2 3.00
electrode as required, including carriage of
materials within all leads and lifts.

165.00 Supplying and laying 6 Sqmm [Link] at 0.50 mtr Rmt 50 20 x 2= 40 90.00
below ground level for conductor earth electrode,
including soldering etc. as required including
carriage of materials within all leads and lifts.
166.00 Providing, fixing & testing Street Light Fixture with Each 5 5.00
CFL of 36 watt, copper ballast, G.I. Pipe bracket,
complete in all respects.
167.00 Supplying and fixing of integral CFL Post Top Each 5 5.00
Lantern of following capacity, cast aluminium
spigot, spun aluminium canopy, opal acrylic
diffuser, complete with all accessories but excluding
CFL lamp including making connections,testing etc.
168.00 Providing and laying of one No. aluminium 0.00
conductor, PVC insulated and PVC sheathed,
armoured / XLPE power cable, working voltage
1100 volts grade direct in ground; to be laid 1 meter
below the ground level including excavation sand
cushioning, protective covering and refilling the
trench etc. of the required size:-

168.01 Armoured cable 4 sq. mm (twin core) P/Mtrs 60 60.00

168.02 Armoured cable 6 sq. mm (twin core) P/Mtrs 50 50.00

169.00 Supplying and fixing following rating, double pole Each 3 3.00
(single phase & neutral) 240 volts, residual current
circuit breaker (RCCB),having a sensitivity current
170.00 Providing
up to 300 and installation
miliampers of existing
in the exhaustMCBfan ofDB
following 0.00
sizes in the existing opening, including making the
hole to suit the size of the above fan, making good
170.01 the
Exhaust Fan, Heavy duty, 300
damages,connections, mmand
testing sweep Each 2 2.00

170.02 Exhaust Fan, Heavy duty, 600 mm sweep Each 1 1.00

171.00 Providing and fixing of Street Light Aqua Roadway Each 5 5.00
Lumairies " WAVE" (IP-66) single pole peice,
pressure die cast aluminium housing top opening
luminaries ( IP-66) with all accessories i/c cost of
lamp ISI Mark BGWRLL-150-SV FG PDC make
complet with all accessories and balast i.e 15/16
Amp Switch and socket with board copper wire 8
SWG ( 4mm dia ) bracket and suitable angle lamps
for fixing and other fittings etc complete in all
respects.
172.00 Providing, fixing & testing Street Light Fixture with Each 1 x 2= 2 2.00
CFL of 36 watt, copper ballast, G.I. Pipe bracket,
complete in all respects.

173.00 Supply, delivery, erection and commissioning of Job 1 1.00

pressure transmitter, GSM based remote terminal
unit with analog and digital parameter,GSM/GPRS
wireless communication modem, electromegnatic
flow meter, equators,SCADA software.
1 2 3 4 5 6 7 8 9 10 11

Executive Engineer,
Jalshakti Division No.1 Una