Data sheet 6ES7142-6BR00-0BB0

SIMATIC ET 200eco PN, DQ 8x 24 V DC/2A, M12-L, 8x M12, single and double

assignment, source output (PNP,switching to P potential), substitute value output,
channel diagnostics for wire break and short-circuit at the output, shared device
with 2 controllers, 0.25 ms isochronous mode, prioritized startup, MSO, MRP, S2
redundancy, I&M0...3, multi-fieldbus, PN IO, Ethernet IP, Modbus TCP, degree of
protection IP67 / IP69K

General information
HW functional status FS06
Firmware version V5.1.x
● FW update possible Yes
Vendor identification (VendorID) 002AH
Device identifier (DeviceID) 0306H
Manufacturer ID according to ODVA (VendorID) 04E3H
Device ID according to ODVA (Product code) 0FA7H
Product function
● I&M data Yes; I&M0 to I&M3
● Isochronous mode Yes
● Prioritized startup Yes
Engineering with
● STEP 7 TIA Portal configurable/integrated from version STEP 7 V17 or higher with HSP 0363
● PROFINET from GSD version/GSD revision GSDML V2.3.x
● Multi Fieldbus Configuration Tool (MFCT) from V1.3 SP1
Operating mode
● DQ Yes
● MSO Yes
Supply voltage
power supply according to NEC Class 2 required No
Load voltage 1L+
● Rated value (DC) 24 V
● permissible range, lower limit (DC) 20.4 V
● permissible range, upper limit (DC) 28.8 V
● Reverse polarity protection Yes
Load voltage 2L+
● Rated value (DC) 24 V
● permissible range, lower limit (DC) 20.4 V
● permissible range, upper limit (DC) 28.8 V
● Reverse polarity protection Yes; against destruction
Input current
Current consumption (rated value) 65 mA; without load
from load voltage 1L+ (unswitched voltage) 12 A; Maximum value
from load voltage 2L+, max. 12 A; Maximum value
Power loss
Power loss, typ. 8.2 W
Address area
Address space per module
● Inputs 1 byte for QI information

6ES71426BR000BB0 Subject to change without notice

2/21/2025
Page 1/5 © Copyright Siemens
 ● Outputs 1 byte
Hardware configuration
Submodules
● Number of configurable submodules, max. 2
Digital outputs
Number of digital outputs 8
Current-sourcing Yes
output characteristic acc. to IEC 61131, type 2 Yes
Short-circuit protection Yes; per channel, electronic
● Response threshold, typ. 4A
Limitation of inductive shutdown voltage to Type -14 V
Controlling a digital input Yes
Switching capacity of the outputs
● with resistive load, max. 2A
● with inductive load, max. 2A
● on lamp load, max. 10 W
Load resistance range
● lower limit 12 Ω
● upper limit 4 kΩ
Output voltage
● for signal "1", min. 2L+ (-0,8 V)
Output current
● for signal "1" rated value 2A
● for signal "1" permissible range, max. 2A
● for signal "0" residual current, max. 0.2 mA
Output delay with resistive load
● "0" to "1", max. 50 µs; at rated load
● "1" to "0", max. 100 µs; at rated load
Parallel switching of two outputs
● for uprating No
● for redundant control of a load Yes
Switching frequency
● with resistive load, max. 100 Hz
● with inductive load, max. 0.5 Hz
● on lamp load, max. 1 Hz
Total current of the outputs
● Current per module, max. 8A
Cable length
● unshielded, max. 30 m
Interfaces
Number of PROFINET interfaces 1
1. Interface
Interface type PROFINET with 100 Mbit/s full duplex (100BASE-TX)
Interface types
● M12 port Yes; 2x M12, 4-pin, D-coded
● Number of ports 2
● integrated switch Yes
Protocols
● PROFINET IO Device Yes
● Open IE communication Yes
Interface types
M12 port
● Autonegotiation Yes
● Autocrossing Yes
● Transmission rate, max. 100 Mbit/s
Protocols
Supports protocol for PROFINET IO Yes
PROFIsafe No
EtherNet/IP Yes
Modbus TCP Yes

6ES71426BR000BB0 Subject to change without notice

2/21/2025
Page 2/5 © Copyright Siemens
 PROFINET IO Device
Services
— IRT Yes; 250 µs to 4 ms in 125 µs frame
— Prioritized startup Yes
— Shared device Yes
— Number of IO Controllers with shared device, max. 2
Redundancy mode
● PROFINET system redundancy (S2) Yes
— on S7-1500R/H Yes
— on S7-400H Yes
● PROFINET system redundancy (R1) No
● H-Sync forwarding Yes
Media redundancy
— MRP Yes
EtherNet/IP
Services
— CIP Implicit Messaging Yes
— CIP Explicit Messaging Yes
— CIP Safety No
— Shared device Yes; 2x EtherNet/IP Scanner
— Number of scanners with shared device, max. 2
Updating times
— Requested Packet Interval (RPI) 2 ms
Redundancy mode
— DLR (Device Level Ring) No
Address area
— Address space per module, max. 20 byte
— LargeForwardOpen (Class3) No
Modbus TCP
Services
— read coils (code=1) Yes
— read discrete inputs (code=2) Yes
— Read Holding Registers (Code=3) Yes
— write single coil (code=5) Yes
— write multiple coils (code=15) Yes
— Write Multiple Registers (Code=16) Yes
— Parameter change by master No
— Modbus TCP Security Protocol No
Address space per station
— Address space per station, max. 20 byte
— Access-consistent address space 2 byte
Updating time
— I/O request interval 2 ms
Connections
— number of connections per device 12
Open IE communication
● TCP/IP Yes; (only EtherNet/IP or Modbus TCP)
● SNMP Yes
● LLDP Yes
● ARP Yes
Isochronous mode
Equidistance Yes
shortest clock pulse 250 µs
max. cycle 4 ms
Jitter, max. 10 µs
Interrupts/diagnostics/status information
Substitute values connectable Yes
Alarms
● Diagnostic alarm Yes; Parameterizable
● Maintenance interrupt Yes; Parameterizable
Diagnoses

6ES71426BR000BB0 Subject to change without notice

2/21/2025
Page 3/5 © Copyright Siemens
 ● Diagnostic information readable Yes
● Monitoring the supply voltage Yes
— parameterizable Yes
● Wire-break Yes
● Short-circuit Yes; Outputs to M; channel by channel
Diagnostics indication LED
● RUN LED Yes; green LED
● ERROR LED Yes; red LED
● MAINT LED Yes; Yellow LED
● NS LED Yes; green/red LED
● MS LED Yes; green/red LED
● IO LED Yes; red/green/yellow LEDs
● Channel status display Yes; green LED
● for channel diagnostics Yes; red LED
● For load voltage monitoring Yes; green LED
● Connection display LINK TX/RX Yes; green LED, only link
Potential separation
between the load voltages Yes
between Ethernet and electronics Yes
Potential separation channels
● between the channels No
● between the channels and the power supply of the Yes
electronics
Isolation
tested with
● 24 V DC circuits 707 V DC (type test)
● Test voltage for interface, rms value [Vrms] 1 500 V; According to IEEE 802.3
Degree and class of protection
IP degree of protection IP65/67/69K
Standards, approvals, certificates
Suitable for safety-related tripping of standard modules Yes; From FS02
Ecological footprint
● environmental product declaration Yes
Global warming potential
— global warming potential, (total) [CO2 eq] 63 kg
— global warming potential, (during production) [CO2 12.7 kg
eq]
— global warming potential, (during operation) [CO2 52.8 kg
eq]
— global warming potential, (after end of life cycle) -2.65 kg
[CO2 eq]
Highest safety class achievable for safety-related tripping of standard modules
● Performance level according to ISO 13849-1 PL d
● Category according to ISO 13849-1 Cat. 3
● SIL acc. to IEC 62061 SIL 2
● remark on safety-oriented shutdown https://support.industry.siemens.com/cs/de/en/view/39198632
Use in hazardous areas
● Explosion protection category for gas ATEX, UKEX, IECEx, CCCEx for Zone 2
● Explosion protection category for dust ATEX, UKEX, IECEx, CCCEx for Zone 22
product functions / security / header
signed firmware update Yes
safely removing data Yes
Ambient conditions
Ambient temperature during operation
● min. -40 °C
● max. 60 °C
Altitude during operation relating to sea level
● Ambient air temperature-barometric pressure-altitude Up to max. 5 000 m, at installation height > 2 000 m additional restrictions
connection method
Design of electrical connection 4/5-pin M12 circular connectors
Design of electrical connection for the inputs and outputs M12, 5-pin, A-coded

6ES71426BR000BB0 Subject to change without notice

2/21/2025
Page 4/5 © Copyright Siemens
 Design of electrical connection for supply voltage M12, 4-pin, L-coded
Dimensions
Width 45 mm
Height 200 mm
Depth 48 mm
Weights
Weight, approx. 780 g
Classifications
Version Classification

eClass 14 27-24-26-04
eClass 12 27-24-26-04
eClass 9.1 27-24-26-04
eClass 9 27-24-26-04
eClass 8 27-24-26-04
eClass 7.1 27-24-26-04
eClass 6 27-24-26-04
ETIM 9 EC001599
ETIM 8 EC001599
ETIM 7 EC001599
IDEA 4 3566
UNSPSC 15 32-15-17-05

Approvals / Certificates
For use in hazard-
General Product Approval
ous locations

Manufacturer Declara- CCC-Ex

tion

For use in hazardous locations Marine / Shipping

Miscellaneous

Food, Pharmaceut-
Marine / Shipping
ical, Medical

NK / Nippon Kaiji Ky- CCS (China Classifica- Confirmation

okai tion Society)

Environment Industrial Communication

PROFINET

last modified: 11/22/2024

6ES71426BR000BB0 Subject to change without notice

2/21/2025
Page 5/5 © Copyright Siemens