PRE - PRINTED WIRE MARKERS

Porta-Pack® Wire Marker Books

 PORTA - PACK BOOKS
Vinyl Cloth (B-500)
Part Markers
Number LEGEND each Legend
PWM-PK-1 0-9 45
PWM-PK-2 A - Z, 10
0 - 15,
, , /
PWM-PK-3 1 - 45 10
PWM-PK-4 1, 2, 3 150
PWM-PK-5 A, B, C 150
PWM-PK-6 T1, T2, T3 150
PWM-PK-7 L1, L2, L3 150
PWM-PK-8 1 - 15 6
16 - 90 4
A - Z,
, , /, 0 2
PWM-PK-9 1, 2, 3, A, B, C 45
T1, T2, T3, L1, L2, L3 30
PWM-PK-10 10 different 45
NEMA colors
PWM-PK-11 1 - 30 15
PWM-PK-12 A-Z 15
Write-On Labels (Blank) 18

8
 7
PWM-PK-13
, , AC, DC 45
 POS, NEG, GND, NEUT 33
Ten pages per book
PORTA-PACK WIRE MARKER BOOKS PRE-PRINTED WIRE MARKERS


Spare 21
Slim, lightweight, pocket-sized book is easy to carry and easy to use Blank Write-On Labels 21

Large selections of legends available; 15 different books and 250 different refill packs PWM-PK-14 46 - 90 10

Numbers…letters…special symbols…NEMA colors PWM-PK-15 1 - 45 5
 46 - 90 5
Includes terminal marker with each wire marker

 PORTA - PACK BOOKS WITH TELECOMMUNICATION LEGENDS


Ten pages per book.

Customized for telecommunication applications.
D
D
A
A
B
B
C
C
1
1
1
1
2
2
2
2
3
3
4
4
5
5
6
6

E
E

Part Size Markers

PHONE
PHONE
PHONE
PHONE

Number Material Inch (mm) Each Legend

F
F

TCOM-PK-1 B-621 0.625 x 0.187 20 (min)

MODEM
MODEM
MODEM
MODEM

Polyester Film (15.88 x 4.75)

VIDEO
VIDEO
VIDEO
VIDEO

VOICE
VOICE
VOICE
E-NET
E-NET
E-NET
E-NET

DATA
DATA
DATA
LAN
LAN
LAN
LAN
FAX
FAX
FAX
FAX

TCOM-PK-2 B-969 0.625 x 0.187 20 (min)

Metallized Polyester (15.88 x 4.75)
PRINTER
PRINTER
VOICE 1
VOICE 1
VOICE 1
VOICE 1
VOICE 2
VOICE 2
VOICE 2
VOICE 2
VOICE 3
VOICE 3
VOICE 4
VOICE 4
DATA 1
DATA 1
DATA 1
DATA 1
DATA 2
DATA 2
DATA 2
DATA 2
DATA 3
DATA 3
DATA 4
DATA 4

 LOAD CENTER AND RESIDENTIAL WIRE MARKERS


DEN OUTSIDE LIGHTS LIGHTS
Fits right on switch or circuit breaker.
MAIN BEDROOM 2 HEATING 2

DEN
MASTER BATH
ATTIC
ATTIC
LIGHTS
LIGHTS
REFRIGERATOR
FREEZER
BEDROOM 2
BEDROOM 3
AIR COND 1
AIR COND 2
Comes in ten page pocket-sized book for convenient use (five
MASTER BATH
BATH 1
BASEMENT
BASEMENT
LIGHTS
LIGHTS
RANGE
DISPOSAL
BEDROOM 3
BEDROOM 4
WATER HEATER 1
WATER HEATER 2
cards each of two legends).
BATH 1 UTILITY ROOM OUTLETS COMPACTOR BEDROOM 4 WASHER
BATH 2 UTILITY ROOM OUTLETS DISHWASHER WHIRLPOOL HEATER DRYER
BATH 2 DRIVEWAY LIGHTS OUTLETS KITCHEN WHIRLPOOL SUMP PUMP
SMOKE DETECTOR
SMOKE DETECTOR
POOL
POOL HEATER
OUTLETS
OUTLETS
KITCHEN
KITCHEN
VENT SYSTEM
ENTERTM’T CENTER
WATER PUMP
FAMILY ROOM
Vinyl Cloth (B-500)
GARAGE SHED SECURITY OUTLETS MASTER BEDROOM REC ROOM FAMILY ROOM
GARAGE
SUNROOM
SYSTEM GFCI
GFCI
MASTER BEDROOM REC ROOM LIVING ROOM Part Size Markers
MASTER BEDROOM PATIO LIVING ROOM
SUNROOM
ENTRY LIGHTS
LIGHTS GFCI
GFCI
BEDROOM 1 PATIO DINING ROOM Number Inch (mm) Each Legend
BEDROOM 1 HEATING 1 DINING ROOM
PWM-LC-3 1.550 x 0.200 (39.37 x 5.08) 5

262 [Link]
PRE - PRINTED WIRE MARKERS
Pre-Printed Wire Markers Materials Chart

Brady’s exclusive ZipStrip® release card

lets you easily remove the markers you
need, when you need them.

Max. Service
Type Temp. °F (°C) Color Finish Use Special Properties
ACETATE CLOTH
B-12 221 (105) White Matte Wire marker for varnish dip or baking cycles Oil and heat resistant
ALUMINUM FOIL
B-184 266 (130) Silver Matte Permanent debossed marking Heat, oil, solvent and abrasion resistant
OVERLAMINATED TEDLAR®
B-605 260 (127) White Gloss Machine tools; hostile environments Heat, oil, solvent and abrasion resistant
POLYESTER
B-11 266 (130) White Gloss Roll-form wire marking; hostile environments Heat, oil and solvent resistant
B-702 221 (105) White Gloss Vinyl coated; machine tool labeling Oil and mild solvent resistant;
high adhesion
POLYOLEFIN
B-319 221 (105) White Matte Computer printable sleeve markers Permanent; not heat shrinkable
B-321 221 (105) White/Yellow Matte Computer printable sleeve markers Permanent; heat shrinkable

PRE-PRINTED WIRE MARKERS MATERIALS CHART

VINYL
B-292 150 (66) White Matte Machine tool, flat ribbon, and wire marking Conformable, durable; oil, water and mild solvent resistant
B-708 150 (66) White Gloss Indoor/outdoor cable marking Conformable, durable; oil, water and mild solvent resistant;
self laminating
VINYL CLOTH
B-500 180 (82) White/Yellow Matte All-purpose marker Moderate heat, oil and dirt resistance;
high adhesion

Tedlar ® is a registered trademark of DuPont.

[Link] 249
REFERENCE
Master Materials Chart
Brady
Material # Material Color Temp. Range Print Technology Properties & Applications
B-484 Polyester White -40°F to 248°F Thermal Transfer 1 mil white polyester with a permanent, ultra-agressive adhesive. Designed for
(-40°C to 120°C) powder-coated surfaces and curved/angled surfaces.

B-486 Metallized Silver -40°F to 248°F Thermal Transfer Matte metallized polyester with a permanent, ultra aggressive adhesive. Designed
Polyester (-40°C to 120°C) for applications like rating and serial plates that require high adhesion to textured
metals, low surface energy plastics, or powder coated surfaces. ®

B-487 Polyimide White -94°F to 662°F Thermal Transfer Polyimide film with a permanent acrylic adhesive, designed to withstand the
(-70°C to 350°C) various processes, fluxes and cleaning solvents encountered in the manufacture
80 seconds at of printed circuit boards. Matte topcoat provides excellent resistance to solder
662°F (350°C) balling. Can be used for top- or bottom-side component or board identification. ®

B-488 Polyester White -40°F to 320°F Thermal Transfer Electronic PCB and component; bar code label and rating plates. High performance
(-40°C to 160°C) matte white. ®

B-489 Polyester White -40°F to 248°F Thermal Transfer Matte polyester with ultra agressive, permanent adhesive. Designed for high
(-40°C to 120°C) adhesion to textured metals, low surface energy plastics, or powder
coated surfaces. ®

B-490 Polyester White –––– Thermal Transfer This material offers the unique ability to apply identification to a frost
covered/cryogenically frozen surface.

B-495 Polyethylene White -94°F to 464°F Thermal Transfer High temperature PEN film with a permanent acrylic adhesive, designed to
Napthalate (PEN) (-70°C to 240°C) withstand most processes, fluxes and cleaning solvents encountered in the
manufacture of printed circuit boards. Glossy topcoat provides excellent
contrast and smear resistance. Can be used for top- or bottom-side component
or board identification, except bottom-side Through Hole applications. ®

B-497 Polyimide White -94°F to 662°F Thermal Transfer 1-mil low profile polyimide film with a permanent acrylic adhesive, designed to ®

(-70°C to 350°C) withstand the various processes, fluxes and cleaning solvents encountered in the
80 seconds at manufacture of printed circuit boards. Matte topcoat provides excellent resistance to
662°F (350°C) solder balling. Can be used for top- or bottom-side component or board identification.

B-498 Vinyl Cloth White -40°F to 175°F Thermal Transfer Wire, cable and component marking. Reposistionable, removes cleanly.
(-40°C to 70°C) TLS2200® Suitable for general identification.

B-499 Nylon Cloth White -94°F to 194°F Thermal Transfer Wire and electronic component marking. Permanent adhesive. High adhesion
(-70°C to 90°C) Dot Matrix makes all purpose wire marking ideal for environments where heat, cold, oil
ID PRO Plus and dirt are present. Also ideal for laboratory vial identification.
LS2000, TLS2200 ®

B-500 Vinyl Cloth White and -40°F to 180°F Pre-Printed Moderately resistant to heat, oil and dirt. Environments containing heat, oil
Colors (-40°C to 82°C) or dirt. Wire and cable marker. Repositionable.

B-502 Vinyl Cloth White -40°F to 180°F Dot Matrix Resistant to oil, water, humidity. Excellent printability; ink-receptive coating.
(-40°C to 82°C) ID PRO Plus Applications requiring general-purpose permanent or temporary labeling or

REFERENCE MASTER MATERIALS CHART

LS2000 marking with printable or write-on properties. Leaves no adhesive residue when
removed - good EPROM label. Cable and wire markers. Repositionable.

B-503 Cloth White -40°F to 194°F Dot Matrix Highly conformable. Self-extinguishing, printable tag. Designed for wire and
(-40°C to 90°C) cable identification. Meets UL94VTM-0 for flame retardancy.

B-505 Polyester White -40°F to 266°F Dot Matrix Self-extinguishing, white polyester with a zone coated, permanent pressure sensitive
(-40°C to 130°C) acrylic adhesive. Designed to be used as a connector pull tab and passes the
requirements of UL94 VTM-0.

B-508 Nomex® Tag White or -40°F to 180°F Dot Matrix Computer-printable Nomex tag stock. Designed as a high-performance wire
Yellow (-40°C to 82°C) bundle and cable identification tag for use in harsh environments.

B-520 Glass Cloth White -85°F to 932°F Thermal Transfer Woven glass cloth. Adheres strongly to glass and a variety of metal surfaces.
(-65°C to 500°C) Custom Designed to withstand harsh temperatures, acidic and alkaline environments.
No Stock Parts Label is pressure sensitive at room temperature and becomes permanently affixed
at temperatures above 400°C.

B-521 Glass Cloth White, Green, -85°F to 932°F Custom Non-printable woven glass cloth. Adheres strongly to glass and a variety of metal
Red, Purple, (-65°C to 500°C) No Stock Parts surfaces. Designed to withstand harsh temperatures, acidic and alkaline
Yellow environments. Label is pressure sensitive at room temperature and becomes
permanently affixed at temperatures above 400°C.

®
*These materials are UL recognized.
*These materials are CSA approved.
*These materials are AGA approved.
*Refer to the full page charts on pages 280-281 for more
information and complete listing of parts.

[Link] 273