PACE BMS quick wiring guide
This manual for PACE low-voltage household storage BMS;
Note: If you find that the product is inconsistent with the description in this manual during use, please refer to
the actual product.·
Wiring method of PACE BMS board, interface board and battery box
Battery box/BMS board/Interface board
Sampling cable
B+
B-
Interface board
BMS mainboard
BMS board/interface board Interface board BMS board/Interface board
BMS mainboard Sampling cable
BMS terminal
1 2 3 4 1, 2, 3 , 4, corresponding
to battery cell B0~B15,
plugging in the wires in
order from low to high.
10P 20P 6P B+
Description of PACE BMS interface board
Parts name Description
① 4-digit dip switch | Address encoder of the pack, binary, from 0~15.
② R eset switch | R eset BMS or shutdown
1 running indicator lamp, 1 red alarm lamp and 4~6 SOC
③ L ED lamp | lamps.
W hen voltage and current faults occur, dry contact can
④ D ry contact | trigger closure or disconnection.
Communicating
Used to communicated with inverter, and can be used with
⑤ with the inverter | various brands of 485 protocols.
2 1 485 port
4 5 6 7 Communicating
8 Used to communicated with inverter, and can be used with
⑥ with inverter CAN | various inverters of CAN protocol
3 port
Communicating
with 232 the
Used to connect the upper computer, monitor data, read
⑦ communication | working status, modify parameters, etc.
port of the upper
computer
Adopts 8P8C second-order RJ45 socket, and uses standard
network cable for docking, which is used for parallel
⑧ 485 parallel port | connection, can also be used to connect the upper computer
(using 485 cables).
More questions,
Scan code to obtain
you can scan the code
PACE electronic version
to enter official website
of BMS wiring manual
for consultation.
Testing and upgrading tools
RS232 RS485
USB to RS232
6pin or 4pin
USB to RS485 serial
DB9 connector DB9 connector RJ45 crystal head
serial port cable crystal head port cable
The 3rd, 4th , and 5th pins of the crystal head correspond to the B：Crystal head 1, 8 pins;
2nd, 3rd , 5th pins of the DB9 head, which is the TX, RX and GND of A：Crystal head 2, 7 pins;
the bms socket, connecting with the 232 communicationcable;
The crystal heads A (2,7 pins) and B (1, 8 pins) correspond to pins 1
Specific connections are:TX-RX，RX-TX，GND-GND and 2 of the DB9 connector.
CAN box
Wiring description of each interface
Wiring description of Description of RS485
RS232 interface parallel port connection
232 communication 485 communication
BMS Socket BMS Socket
line cable
The 1st ,8th ,9th
RX (2nd pin) TX ( 3rd pin)
,16th be the
Adopt standards same way as B
TX ( 3rd pin) RX (4th pin) Network cable
The 2nd , 7th,
docking
10th ,15th be
the same way
GND(5th pin) GND(5th pin)
as A
Note: BMS sockets are in order from right to Note: BMS sockets are in order from right to
left, for the 1st pin to the 6th pin, the 3rd pin left, for the 1st pin to the 16th pin
is TX, and the 4th pin is RX, and the 5th pin is
GND.
Description of RS485 Description of CAN
communication port wiring interface wiring
485 communication
BMS Socket CAN box BMS socket
cable
The 2nd pin B The 9th, 16th pin CANH The 4th pin
The 10th, 15th
The 1st pin A CANL The 5th pin
pin
Note: BMS sockets are in order from right to Note: BMS sockets are in order from right to
left, for the 1st pin to the 16th pin left, for the 1st pin to the 8th pin
