Privacy Notice upon the purchase of equivalent new equipment, 1.

2 Overview
Surveillance laws vary by jurisdiction. Check all or dispose of it at designated collection points.
relevant laws in your jurisdiction before using For more information see: www.recyclethis.info. 1.2.1 Overview of Type I Camera
this product for surveillance purposes to ensure 2006/66/EC (battery directive):
Please refer to the product specification for This product contains a battery that
Mounting Base
camera parameters and functions. cannot be disposed of as unsorted Power Cable
municipal waste in the European
Regulatory Information Union.
See the product documentation for specific
FCC Information HD Video Cable
battery information. The battery is marked with Sun Shield
FCC compliance: This equipment has been
this symbol, which may include lettering to
tested and found to comply with the limits for a Lens
indicate cadmium (Cd), lead (Pb), or mercury (Hg). IR LED
digital device, pursuant to part 15 of the FCC
For proper recycling, return the battery to your
Rules. These limits are designed to provide
supplier or to a designated collection point. For
reasonable protection against harmful Figure 1-1 Overview of Type I Camera
more information see: www.recyclethis.info.
interference when the equipment is operated in

HDTVI a commercial environment. This equipment Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (A)/NMB-3(A)
generates, uses, and can radiate radio
MiniBullet & Dome Camera frequency energy and, if not installed and used standards requirements.
1.2.2 Overview of Type II Camera
in accordance with the instruction manual, may
User Manual cause harmful interference to radio
Side Opening Mounting Base
communications. Operation of this equipment in
a residential area is likely to cause harmful
interference in which case the user will be Trim Ring Enclosure
required to correct the interference at his own
Thank you for purchasing our product. If there expense.
are any questions, or requests, please do not FCC Conditions 1 Introduction Camera
This device complies with part 15 of the FCC HD Video Cable
hesitate to contact the dealer.
Rules. Operation is subject to the following two 1.1 Product Features
This manual may contain several technical
conditions: Power Cable
incorrect places or printing errors, and the This series of camera adopts new generation
1. This device may not cause harmful
content is subject to change without notice. sensor with high sensitivity and advanced circuit
interference.
The updates will be added to the new version of design technology . It features high resolution, Figure 1-2 Overview of Type II Camera
2. This device must accept any interference
this manual. We will readily improve or update low image distortion and low noise, etc . , which
received, including interference that may
the products or procedures described in the makes it suitable for surveillance system and
cause undesired operation. 1.2.3 Overview of Type III Camera
manual. image processing system.
EU Conformity Statement lHigh performance CMOS sensor and high
This product and - if applicable - the
resolution bring high-quality image;
supplied accessories too are marked
lLow illumination; Enclosure
with "CE" and comply therefore with Camera
lSupport auto white balance;
the applicable harmonized European
lUnit transmission control;
standards listed under the Low Voltage Directive
lAdvanced 3-axis design meets different Trim Ring HD Video Cable
2006/95/EC, the EMC Directive 2004/108/EC,
installation requirements.
the RoHS Directive 2011/65/EU.
Mounting Base Power Cable
2012/19/EU (WEEE directive):
Products marked with this symbol
cannot be disposed of as unsorted
municipal waste in the European Figure 1-3 Overview of Type III Camera
Union. For proper recycling, return
this product to your local supplier
 3.Connect the corresponding power cable and 2. Screw the clip plate onto the mounting base
2 Installation video cable. loosely. 2.3 Installation of Type III Camera
Steps:
Before you start: 4.Fix the camera to the ceiling with the supplied Clip Plate
lPlease make sure that the device in the package screws. 1.Drill the screw holes and the cable hole on the
is in good condition and all the assembly parts ceiling according to the supplied drill template.
are included.
lMake sure that all the related equipment is
power-off during the installation.
lCheck the specification of the products for the
installation environment. Figure 2-5 Screw the Clip Plate
lCheck whether the power supply is matched
with your power output to avoid damage.
lPlease make sure the wall is strong enough to 3. Fix the mounting base to the ceiling with the
Figure 2-2 Fix the Camera to the Ceiling Figure 2-8 The Drill Template
withstand three times the weight of the camera supplied screws.
5.Adjust the surveillance angle. 2.Fix the mounting base to the ceiling with the
and the mounting. 4.Route the cables through the side opening and
1).Loosen No.3 adjusting screw to adjust the supplied screws.
lIf the wall is the cement wall, you need to insert connect the corresponding power cable and
panning position ( 0° ~ 360° ).
expansion screws before you install the camera. video cable.
2).Tighten No.3 adjusting screw .
If the wall is the wooden wall, you can use 5.Pull out the clip plate and secure the camera
3).Loosen the No.2 adjusting screw to adjust the
self-tapping screw to secure the camera. with the trim ring to the mounting base.
tilting position ( 0° ~ 180° ).
lIf the product does not function properly, 6.Push the clip plate in and tighten the lock screw
4).Tighten No.2 adjusting screw.
please contact your dealer or the nearest to secure the trim ring.
5).Loosen No.1 adjusting screw to adjust the
service center. Do not disassemble the camera
for repair or maintenance by yourself. azimuth angle of the image ( 0° ~ 360° ).
6).Tighten No.1 adjusting screw . Side Opening Figure 2-9 Fix the Mounting Base and Camera
Clip Plate 3.Route the cables through the cable hole and
2.1 Ceiling Mounting for Type I
connect the corresponding power cable and
Camera video cables.
4.Secure the camera to the mounting base and fix
Both wall mounting and ceiling mounting are 3 0° to 360° the trim ring to the camera, as shown in the
P Direction
suitable for type I bullet camera. Ceiling mounting figure below.
will be taken as an example in the section. And you 2 0° to 180° j
T Direction
can take steps of ceiling mounting as a reference 1 Figure 2-6 Fix the the Camera
if wall mounting is adopted. 0° to 360°
R Direction
Steps: 7. Adjust the camera according to the figure 2-7 to
Figure 2-3 3-axis Adjustment
1.Drill the screw holes in the ceiling according get an optimum angle and tighten the trim ring.
to the supplied drill template.
2.2 Installation of Type II Camera P Direction Figure 2-10 Fix the Trim Ring to the Camera
2.Hammer the supplied plastic expansion bolt into
Steps: 0° to 360°
the screw holes. 5. Adjust the camera according to the figure below
1.Drill the screw holes according to the drill to get an optimum angle.
template.
R Direction
0° to 360°
0° to 75°
T Direction

Screw hole
Screw hole
Figure 2-7 3-axis Adjustment

Figure 2-1 The Drill Template

Figure 2-4 The Drill Template Figure 2-11 3-axis Adjustment