DATA SHEET
SERIES Interchangeable with
assessed
R5000
5000
Baseefa 10ATEX0002DRR
IP50
Parker Commercial
50 and 51 Series
Roller Bearing Gear Pumps
Motors and Flow Dividers
• Single or multiple units available.
• Piggy back options available.
• Type II mounting available.
• Displacement 21 cc/rev to 105 cc/rev.
• Minimum operating speed 600 rpm.
• Maximum operating speed 2400 rpm.
• Maximum continuous operating pressure
3000 psi (207 bar).*1
• Cast iron construction.
• Dowelled units available.
Mounting Flange Options: Single unit
SAE ‘B’ 2 bolt, SAE ‘B’ 4 bolt, SAE ‘C’ 2 bolt,
SAE ‘C’ 4 bolt.
Drive Shaft Options:
SAE ‘B’ 13 tooth, SAE ‘C’ 14 tooth, SAE ‘B’ 15 tooth,
SAE ‘C’ keyed, Taper shaft.
Various Porting Options:
BSP, SAE, NPT, JIC (ODT).
*1 Only available in 21, 32, 42 and 52cc.
Tandem Unit
Performance and Dimensions overleaf
Recommended Operating
Conditions:
Fluid viscosity, normal operating conditions
16 to 220 cst.
Fluid temperature should not exceed 65°C.
Recommended system oil cleanliness should
be equal to or better than ISO4406 19/17/14.
Inlet pressure; for best operation with
mineral oil, pressure should not exceed minus
LTD 0.237 bar (7 in HG).
Please discuss your application with our sales engineers
Series 5000 Pumps, Motors and Flow Dividers
PERFORMANCE DATA
Input Speed – rpm
Pump Performance
1000 1500 1800 • Flows quoted are at test
pressures of 138 bar/2000 psi,
Output- L/min/igpm – Input-Kw/Horsepower Output Input Output Input Output Input using 32cSt oil at 65° C.
05 1/2 21 207/3000 18 / 4.0 6/8 29 / 6.3 9 / 12 34 / 7.5 11 / 15
• 2.3/4” gear width also
07 3/4 32 207/3000 27 / 5.9 8 / 11 43 / 9.5 14 / 18 51 / 11.2 17 / 23
working pressure–bar/psi
available, ask sales engineers
Displacement – cc/rev
Maximum continuous
Gear widths – inches
Gear widths – code
10 1 42 207/3000 36 / 7.8 11 / 15 57 / 12.6 18 / 24 68 / 15.0 22 / 30 for details.
12 1.1/4 52 207/3000 46 / 10.1 14 / 18 72 / 15.9 22 / 30 87 / 19.2 26 / 35
• Dowelled units also available
15 1.1/2 63 180/2610 54 / 11.9 16 / 21 87 / 19.2 26 / 35 106 / 23.3 31 / 41 5100/51.
17 1.3/4 74 180/2610 67 / 14.8 18 / 24 102 / 22.5 30 / 40 124 / 27.3 36 / 48
• Performance data is derived
20 2 84 180/2610 73 / 16.1 21 / 28 115 / 25.3 34 / 46 139 / 30.6 41 / 54 from tests conducted to
22 2.1/4 95 155/2250 80 / 17.6 23 / 31 126 / 27.8 38 / 51 155 / 34.1 46 / 61 simulate working conditions
Continuous operation at
25 2.1/2 105 155/2250 88 / 19.4 26 / 35 141 / 31.2 43 / 57 173 / 38.1 51 / 69 maximum performance may
compromise unit life
Output Speed – rpm If in doubt when specifying,
Motor Performance please consult our sales
900 1200 1600 2000
department
Output Kw / hp 6.5 / 9.0 10.0 / 13.5 13.0 / 17.5 15.5 / 21.0
10 1 Output Nm / in.lb 82.5 / 730 81.5 / 720 80.0 / 710 75.0 / 670
Input flow. Output hp & torque
Input l.min / igpm 41.0 / 9.0 61.5 / 13.5 77.5 / 17.0 95.5 / 21.0
*Gear widths – inches
Output Kw / hp 10.5 / 14.0 15.5 / 21.0 20.0 / 27.0 24.0 / 32.5
Gear widths – code
15 1.1/2 Output Nm / in.lb 129.0 / 1140 126.5 / 1120 124.5 / 1100 117.5 /1040
Input l.min / igpm 61.5 / 13.5 86.5 / 19.0 116.0 / 25.5 143.0 / 31.5
Output Kw / hp 14.0 / 18.5 21.0 / 28.0 27.5 / 37.0 33.0 / 44.5
20 2 Output Nm / in.lb 173 / 1530 169.0 / 1495 166.0 / 1470 159.5 / 1410 * These gear widths are the
82.0 / 18.0 116.0 / 25.5 154.5 / 34.0 188.5 / 41.5 popular sizes for motor
Input l.min / igpm
configurations but any of the
Output Kw / hp 18.0 / 24.0 26.5 / 35.5 33.5 / 45.0 41.0 / 55.0
gear widths listed in the Pump
25 2.1/2 Output Nm / in.lb 214.5 / 1900 211.5 / 1870 205.5 / 1820 196.5 / 1740 Data table can be supplied.
Input l.min / igpm 100.0 / 22.0 141.0 / 31.0 188.5 / 41.5 234.0 / 51.5
Weights (approximate)
Gear widths (ins) 1/2 3/4 1 1.1/4 1.1/2 1.3/4 2 2.1/4 2.1/2 2.3/4
For multiple unit weights, please
Single unit (kg) 17.0 18.5 19.5 20.5 21.0 22.0 22.5 23.5 24.5 25.5 consult our sales department
Dimensions
5.88
+ Gear Width
149.35
**See **See
Drive ***3.38 .75 1.75 Drive ***3.38 .75 2.88 .75 1.75
Shaft *85.85 19.05 44.45 Shaft *85.85 19.05 73.15 19.05 44.45
Options + Gear Width Options + Gear Width + Gear Width
1.00 1.00
25.40 25.40
6.25 6.25
158.7 158.75
3.12 3.12
79.24 79.24
3.75 3.75 1.81 *5.61
95.25 95.25 45.97 *142.49
1
+ Gear Width
2
1
+ Gear Width
2
1
+ Gear Width
2
Single unit Tandem unit
* Standard port arrangement, dimension will change with ***Dimensions for Type II mounting 2.39
the type of port 60.70
** Dimensional information for mounting flange and shaft
options are shown on the attached Data Sheet FS100.
LTD
HYDRAULIC ENGINEERS
Unit 20 Silver Court, Intercity Way, Bramley, Leeds, West Yorkshire LS13 4LY. UK.
Tel: +44 (0) 113 2361367 Email: [email protected] web: www.hydra-perm.co.uk
