No. of Printed Pages : 7 CC/CE4003 Roll No. MAY 2023 (Semester) THEORY OF STRUCTURES rete ware: 3 2] parftrenert 3a : 60 ‘Time allowed : 3 Hours] [Maximum Marks : 60 mW: (i) wa-watdrdeny aoa Note: There are THREE sections in the paper A, B and C. (i) Baer eA wea Bs BH 10 TT eR Afr | eda ATT es Te TB wt 10 ITT RGAE TER WEA S| Answer all the 10 parts of the question No. I in Section A. Each part carries ‘one mark and all 10 parts have objective type questions. (iti) Barr HH 8 eat HF Frore 6 Meat Fe Gif | Wea WETS aw BT BUT FBT S OT / 50 Wea TR AHA | Answer any 6 questions out of the 8 questions in Section B. Each question carries 3 marks and to be answered within 5 lines / 50 words (iv) Baer at 6 weal FB Peal 4 weal & sere Aiea | eden We 8 sie aT Be For 1S TART / 150 Weel TTA AA | Answer any 4 questions out of the 6 questions in Section C. Each question carries 8 marks and to be answered within 15 lines / 150 words. (vy) eeben aera & areth eat ah sere Ue ATT Ber ITE | Solve all the questions of a section consecutively together. (vi) Gat aranait Fare ai Ht ale F aiitatt sygara aT e | Only English version is valid in case of difference in both the languages. Pt (of 8) P.T.O.CC/ICE4003 (of8) 7155 1. @ (ii) Git) aa -T Section - A Sebiga wa 8 ahaa ere fi ora She fete oor a a frat @ arftres Star Bat al sera eT (@) waiter (o) 7A (© water aa at @ waaatag When direct stress is greater than bending stress in a eccentrically compressed column; then there will be (a) Compression (b) Tension (©) Compression & Tension both (d) None of these SETTER Gs & Rave F ofa Ht wpe aa wh ate ae aa arate fase are | (a) wea geist (b) wea arate (© Fearaguist @ Rida In a rectangular section the stress will be of the same nature throughout the section if the load lies within the of the section. (a) middle third (6) middle half (©) _ middle fourth (@ None of these ren H fata (y) ara eR & fre Fea HS ae eae a Te? ME M @ y= pe &) y= ff © y= [fre @ y= Shan Which of the following is the correct relation for finding deflection (y) in a beam ? @ y= ff w ff co [fe oo y= ffm‘CCICE4003 Gof 8) 7155 (iv) “L” Regt are edicts wet ft yo Regia © o aaftatte a or & rT, Te ) H caren faata err: SoL* oL* ©) 384 ET ©) SET 4 Lt © Sei © StF ‘The maximum deflection, in cantilever beam (Span ‘L”) subjected to UDL of *e’ on whole span, will be SaL* @L* © 384 ET © GET oL* ol © SET @ SEF +L faegta ht ara a, rach ao feegfa oC o oft garg rang ar afeafta ae am S, & a fr sre Tae sept elas - L L? @ © 2 iz © oo @ ‘The magnitude of fixed and moment, at the right support in a fixed beam of span ‘L’ subjected to a UDL of per unit length on its whole span, is L. 1b? @ 6 © L? yb? © oF oF (vi) Prafeaa a a ota ft ae sifted 3 2 @ eae we (b) sag a (oc) estefan ret (@) Weare sitees ae Which of the following is an indeterminate beam ? (a) Simply supported beam () Fixed beam (©) Cantilever beam (4) Simply supported overhang beam P.O.CC/CE4003 (4 of 8) 7155 (vil) Je arenas orca Ht ofaieen & feng ware et ere tear seit AM srrephe Set B - (a) Buster (>) Farr (© Tact @) Hae ‘The shape of influence line diagram for reaction of a simply supported beam, will be: (@) Triangular () Circular (©) Parabolic (@ Rectangular (vii) 100 KN TG wet AK 20 m Pegi Ft wwe Yaraltaa aa Mase g, arftenar dapa aarept a - (@) 100 kN-m (6) $00 KN-m © S500KN @ 250kNm (x) oy A single load of 100 KN rolls along a simply supported beam of 20 m, the maximum bending moment will be @ 100kN-m (b) 500 kN-m (© S00kN (@) 250kNm We ye arrest cian 8 @ fa (bo) sit © a @ wae The basic perfect frame is (2) Triangle (b) Rectangle (©) Square (® Hexagon ‘Sits fafer at ugaa act 8g fase Sits Tara acti Al aiftrere ce A ee @ 1 @) 2 © 4 @ 3 Method of joint is applicable only when the number of unknown forces at the joint under consideration is not more than @ 1 () 2 © 4 @ 5 (1x10)CC/CE4003 (of8) aan- at Section -B 2, fad agen a wards fie Gd fw Sef Homer we fife | Differentiate between compound fink and fink truss with the help of sketch. 3, fia sits cial & facia ¥ oft wf araersit at aaa | Explain the assumptions made in the analysis of pin jointed frames. 4, werd cre we fae fae act oe Pit wee? ‘On what factors the slope and deflection in a beam depends ? 5. Hie UGS Recta pean & fara at are | Explain principle of superposition in the analysis of fixed beams. 6, mea agate fre sar 2 ‘What is the middle fourth rule ? 7155 @) e& 8) 8) ) 7. ee 3 thee are Seticftae oes & gas PRE TS KN ar fieg aR rT ga 2 | oT onftraran are we Paeta are FAG | BL ATA STR APR | ‘A cantilever beam is 3 m long and is acted upon by a point load of 5 KN at the free end, Find out the maximum slope and deflection in the beam. Take EI as constant. 8, ward tar atte ws gee oer aesTET | Explain influence line diagram and its uses. @) @) P10.CCICE4003 (6 0f8) 155 9, faa e1 Sata srg eres & chal et ae a sere ar aa ocr eh 7 ‘What will be the value of fixed end moments at both ends of the given fixed beam in 1 (3) figure. 1 > @) A B —— $ —*— § —4 fad. -1/ Figure 1 aan - at Section—C 10. 200 mm ANS GE 150 mm Ae eaeT A erg wt aH BEI are eT 20 mm. AL TPR TW 60 KN Br Sea A AT Te! | BTN} are oR afr ea TT ferret ara fag | A column of 200 mm wide and 150 mm thick carries a vertical load of 60 KN at an eccentricity of 20 mm on the axis bisecting the thickness. Find the maximum and minimum stress on the base of the column. ®) 11. fa-erererere fee grat fara a. 2 ah ag eer & fore orate da & aetewe ware eT rer tre crete fade ser aa aa fare | EL ore ehhh | By using Double Integration method, prepare equations for slope and deflection and find out the value of the maximum slope and deflection for the given beam in figure 2. Take EI as constant. ® 4 kN/n A B 5m ————_>| ~2/Figure2 12. fea a. 3 9 qahti owh arag ue & fee dea reel ante wa adh aa oty, vem ‘arama fae ara wage | Draw the bending moment diagram and shear force diagram using first principle method, for the fixed beam shown in figure 3. 8) 30 ke ° A B k$— 4m ——%*—— 4m —— fad. —3/ Figure 3CCICE4003 (70f8) 7185 13, fara. 4H fea ae aia & ash areal 8 eer gra Hire | Find out the forces in all the members of the given truss in figure-4. ® ] | 4m . ic —E 3m 3m 40 kN 30KN fad. —4/ Figure 4 14. drafear ae 16 N48 N (16 NAR TM) GH 10 er fag ha Ht oa TOTS S| Sa aT sara & tte eh 2 her 2 1 ard fart a St sex A an Sea orp & fore wae tar wriga @ afta dara arrept ara AST | ‘Two wheel loads of 16 N & 8 N (16 N load leading) crosses a beam of span 10 m. Distance between two loads is 2 m. Draw the influence line for bending moment at a section 2 m from left support and calculate maximum bending moment. () 15. We 125 Rett Ast wa 200 Fee aterg aA Aesteftan eres 3 alex eat B 1 ale gee Fate 4 finh 2 sift fadta a a at oer Ge a @ faahea aR ae APE | aT A 200 GN/m? zfifarg | ‘A cantilever beam 125 mm wide and 200 mm deep is 3 m long. Calculate the uniformly distributed load, which the beam should carry; if the deflection of the free end should not exceed 4 mm. Take E = 200 GN/m?. (8)CC/CE4003 (of 8) 7155.