BEI LEVEL IV COC
1. From those of electric current a generation of heat due the friction created
by the movement of electrons produced by.
A/ Inductive material B/Semiconductor element
C/ Capacitive material D/ Resistive Element
2. One thing that the air conditioner performs but be ordinary ventilator
cannot.
A/ The ordinary ventilator can set required temperature
B/ The air conditioner perform by setting temperature
C/ The ordinary ventilator can perform in hot area only
D/ They are almost the same both do the same thing
3. A Light source of intensity 450cd is 3m above he point and the second point
4m from the first point .determine the illumination of the first and the
second?
A/ 15 ande 20lux B/ 12.5 and 30lux
C/ 20 and 30 lux D/ 50 and 10.8 lux
To determine the illumination at the first and second points, we can use the
formula for luminance (E) based on the inverse square law:
E = I / d^2
Where:
- E is the luminance (in lux)
- I is the intensity of the light source (in candela)
- d is the distance from the light source (in meters)
Given information:
- Light source intensity (I) = 450 cd
- Distance to the first point (d1) = 3 m
- Distance to the second point (d2) = 4 m
Calculation for the first point:
IL luminance (E1) = I / d1^2
E1 = 450 cd / (3 m)^2
E1 = 50 lux
Calculation for the second point:
IL luminance (E2) = I / d2^2
E2 = 450 cd / (4 m)^2
E2 = 28.125 lux
Rounding the result for the second point to one decimal place, the answer is:
B) 12.5 and 30 lux
The other options are incorrect:
A) 15 and 20 lux: The calculated values are different from these.
C) 20 and 30 lux: The calculated value for the first point is different.
D) 50 and 10.8 lux: The calculated values are different from these.
Therefore, the correct answer is B) 12.5 and 30 lux.
4. Main disadvantage of steel conduit.
A/ internal condensation result insulation damage.
B/ it can be used as circuit protective conductor
C/ complete protection against fire hazard
D/ Not withstand especially mechanical accident
5. Ignoring contingencies point for electric contractor has consequence.
A/ produce much profit for contactor
B/ Intensive labor work produces work area
C/ Quality finishing accomplished
D/ Delaying the project and produce deficit
6. Most affected area by unbalanced 3 phase voltage supply?
A/ Industrial motor control area
B / part of building lighting area
C/ part of heating appliance area
D/ General purpose socket area
7. Which is mainly required to determine the dimension of building for preparing
wiring estimation?
A/ schedule of work B/ drawing layout
C/ Types of building D specification of materials
8. Consider the residual current device (RCD), according to I.E.E the maximum
voltage to earth when a fault occurs should not exceed.
A/ 70 volt B/ 40 volt C/ 50 volt D/ 80 volt
9. The first step in the design of lighting system is ………………………
A/ Determine the method of lighting
B/ Identify the requirements
C/ select the lighting equipment
D/ calculate the lighting parameters
equipment, and calculate the necessary lighting parameters to meet the
identified needs.
Therefore, the correct answer is B) Identify the requirements.
10. …………is widely used in analog telephone to connect the phone.
Tele socket outlet through coaxial cable. A/ RJ45 connector
B/ RJ11 connector C/ Terminal lug connector D/ BNC connector
11 The advantage of overhead trucking system
A/ carries small load B/ fitting is simple C/ Expansion is easy D/ Not
exposed to danger
12. The average passenger lifting speed of elevator.
A. 2-5m/hr. B. 5-22m/hr. C. 20-40m/hr. d. 10-20m/hr.
13. which one of the following electrical equipment/apparatus is resistive load?
A. florescent lamp B. cloth iron C. motor D. LED lamp.
14. Which type of lighting schemes mostly used for indoor light decoration?
A. Direct lighting incandescent B. semi direct lighting
C. semi direct lighting D. Direct lighting fluorescent
15. If the circuit breaker trips without significant short circuit, the expected
problem will be
A. A phase to neutral contact B. A disconnect of phase wire
C. A phase to wet ground contact D. A phase to phase contact
16. Rigid and flexible conduits are jointly used.
A. when all equipment require supply from ground
B. when all machines and equipment are taking supply from ground
C. for industrial installation
D. when all machines are installed horizontally from its source
17. Which type of special low voltage circuit must not be drawn in the same
enclosure?
A. Heating and ventilation circuit
B. Socket and lighting circuit
C. Lighting and bell circuit
D. fire alarm and emergency circuit
18. Electrical protection devices are primarily required to protect.
A. Electrical devices B. Conductors and cable
C. Customers D. The power system
19. Discrimination of circuit breaker in main distribution board helps to:
A. Display consumed current of system
B. Organize consumed power of system
C. Sustain systems in case of problem
D. Decide how many breakers allotted for a system
20. For 40 household an average 4000 watt per head allocated how much size of
transformer do you order?
A. 250kva size B. 160 kw size C. 500 kva size D. 350 kw size
21. This standard drawing symbol of electrical equipment /device means.
A. The equipment functions at > 45 degree
B. keep the equipment away from children
C. The equipment has a voltage regulator inside
D. The equipment is double insulated
To calculate the required transformer size for 40 households with an average of
4000 watts per head, we can use the following formula:
Total power demand = Number of households × Average power per household
Total power demand = 40 × 4000 watts = 160,000 watts
To convert this to the required transformer size in kVA, we can use the formula:
Transformer size (kVA) = Total power demand (watts) / 1000
Plugging in the values:
Transformer size (kVA) = 160,000 watts / 1000 = 160 kVA
Therefore, the appropriate transformer size to order would be a 250 kVA
transformer, as it is the closest standard size that can accommodate the total
power demand.
22. Which one of the following help cost estimate of work order as accurate as
possible?
A. Deal agreement between owner and supervisor
B. Refer up-to-date information from manufacturer
C. Guess the price inadequate information about material
D. Direct contact with wholesales and dealers
23. What happens if undersized cable is used for connecting pump-motor set?
A. over voltage and pump speed increases
B. Over loading of the cable and speed
C. Under loading of the cable and speed decreases
D. under voltage and pump speed decreases
24. If light source of intensity 450 Cd is 3 meter directly above the point and the
second point 4 meter from the first point the illumination in the first and
second point.
A. 15 and 20 lux C. 12.5 and 10.5 lux
B. 50 and 10.8 lux D. 20 and 30 lux
The correct answer is B) 50 and 10.8 lux.
To calculate the illumination at the first and second points, we can use the
formula for luminance (E) based on the inverse square law:
E = I / d^2
Where:
- E is the luminance (in lux)
- I is the luminous intensity of the light source (in candela, Cd)
- d is the distance from the light source (in meters)
For the first point:
Distance (d1) = 3 meters
Luminous intensity (I) = 450 Cd
IL luminance (E1) = I / d1^2
E1 = 450 / (3^2) = 50 lux
For the second point:
Distance (d2) = 4 meters
Luminous intensity (I) = 450 Cd
IL luminance (E2) = I / d2^2
E2 = 450 / (4^2) = 10.8 lux
Therefore, the illumination at the first point is 50 lux, and the illumination at the
second point is 10.8 lux.
The other options are incorrect:
A) 15 and 20 lux: This is not the correct answer.
C) 12.5 and 10.5 lux: This is not the correct answer.
D) 20 and 30 lux: This is not the correct answer.
So, the correct answer is B) 50 and 10.8 lux.
25. A current transformer with 20:5 ratio in a distribution board indicates………….
A. The total flow of current from the source
B. Primary side to source & secondary to an ammeter
C. primary side to an ammeter & secondary to high voltage
D. Rating of current and voltage of the system
26. According to IEC regulation a 10-ampere miniature circuit breaker control.
A. 8 incandescent lamps B. 15 incandescent lamps
C. 20 incandescent lamps D. incandescent lamp
According to the IEC (International Electro technical Commission) regulations, a
10-ampere miniature circuit breaker (MCB) can control a maximum of 8
incandescent lamps.
Let's explain the reasoning behind this:
A) 8 incandescent lamps: This is the correct answer.
The IEC regulations state that the maximum load that can be connected to a 10-
ampere MCB should not exceed 80% of the rated current. This is to account for
potential overloads and ensure the circuit breaker can effectively protect the
circuit.
Calculation:
- Rated current of the MCB = 10 Amps
- 80% of 10 Amps = 8 Amps
- Assuming each incandescent lamp has a power rating of 100 watts and operates
at 230 volts, the current drawn by each lamp would be:
Current = Power / Voltage = 100 W / 230 V = 0.435 Amps
- Therefore, the maximum number of incandescent lamps that can be connected
to a 10-Amp MCB is 8 (8 Amps / 0.435 Amps per lamp).
B) 15 incandescent lamps: This is incorrect. The maximum number of
incandescent lamps that can be connected to a 10-Amp MCB is 8, not 15.
C) 20 incandescent lamps: This is also incorrect. The maximum number of
incandescent lamps that can be connected to a 10-Amp MCB is 8, not 20.
D) Incandescent lamp: This is not a complete answer. The question specifically
asks about the number of incandescent lamps that can be controlled by a 10-Amp
MCB.
Therefore, the correct answer is A) 8 incandescent lamps, as per the IEC
regulations.
27. The final most probable solution,if cook top heating is open circuited is
A. Check –up thermostat and replace
B. Replace heating element
C. Adjusting work time
D. Check –up incoming if the cooktop heating is open-circuited, the most
probable solution is to replace the heating element.
28. Most elevator provided for home go through up to ………………..floor.
A. 7 B. 5 C. 3 D. 2 The correct answer is B) 5 floors.
29. ………………. Is fabricated casing for conductor use to laid rather than drawn.
A. Trucking B. Metallic conduit C. PVC conduit D. Flexible conduit
Trucking is the fabricated casing for conductor use that is laid rather than drawn.
30. If short circuit present in an electrical installation circuit what will be testing
result expected?
A. The millimeter reading constantly vary
B. The millimeter shows almost zero resistance
C. . The millimeter shows infinite resistance
D. The millimeter display high resistance
31. The very beginning start of work after interpreting blue print is?
A. start to fix accessories C. perform wiring system
B. Collect material for termination D. Start to erect conduit .
33. The minimum size of PVc conduit used in electrical installation wiring is
…………..
A. 16mm diameter B. 20mm diameter
C. 12mm diameter D. 24mm diameter
34. Technical wiring diagram contains information of…………….
A. How to scale up drawing fixtures and apparatus
B. All fixtures location with technic of wiring
C. the overall information of apparatus
D. how to disassemble and assemble fixtures
35. Which point is to be considered while panning for load in wiring installation?
A, Type of dwelling area
B. Selections of brand of materials
C. provision for the anticipated increase in loads
36. standard wire size next to 16mm2 and 50mm2 respectively is ;
A. 20mm2 and 80mm2 B. 10mm2 and 50mm2
C. 35mm2 and 70mm2 D. 25mm2 and 70mm2
37. Which of the following measuring instrument used to light intensity?
A. Galano meter B. Photo meter
C. current meter D. Volt meter
A) Galvanometer: A galvanometer is an instrument used to measure electric
current, not light intensity.
C) Current meter: A current meter is used to measure electric current, not light
intensity.
D) Voltmeter: A voltmeter is used to measure electric voltage, not light intensity.
A photometer is a specialized instrument designed to measure the intensity or
brightness of light. It works by converting the light energy into an electrical signal,
which can then be displayed or recorded as a measurement of the light intensity.
Photometers are commonly used in various applications, such as:
- Lighting design and evaluation
- Photographic exposure metering
- Measurement of illumination levels in buildings, streets, and other
environments
- Quality control in manufacturing processes involving light-sensitive materials
- Research and scientific experiments related to light and optics
Compared to the other options, which are used for measuring electrical
quantities, a photometer is the appropriate instrument for measuring light
intensity, making it the correct answer.
Therefore, the correct answer is B) Photometer.
38. The best precautions taken when removing fuse from control board?
A. Find the incoming wire to a fuse
B. Check which fuse you are going to replace
C. Ensure the circuit is not carrying current
D. Wear proper eye glass for safety case
39. Which work analyzed first to select & install industrial motor control board?
A. knowing voltage rating of motor
B. Identifying insulation class of a motor
C. Calculating load current of motor
D. Identifying duty class of a motor
40. Which of the following work area usually does not require bench work?
A. preparing sufficient work place
B. prepare scaffold for building
C. fixing junction box in flush mounted
D. Adjusting emergency exit area
41. The voltage drops between the supply terminal and fixed current-using
equipment.
A. Shall not exceed 4% of the nominal voltage of supply line
B. It could not be exceed to 5% of the nominal voltage of the supply line
C. It could not exceed 2% of the design voltage of the supply line
D. It could be equivalent to 10% of the nominal voltage of the supply line
42. Depending on the elevator shaft the voltage supply ranges
A. From 1000 volt /100 ampere up to 1100v/150 ampere
B. from 550 volt/50 ampere up to 380v/38 ampere
C. from 100 volt/20 ampere up to 22v/30 ampere
D. 400 volt/40 ampere up to 220 volt/30 ampere
43. The recommended cable size for general purpose socket outlet is:
A. 1mm2 copper conductors
B. 2.5mm2 aluminum conductor
C. 4mm2 copper conductor
D. 2.5mm2 copper conductor
44. Which of the following electric load causes high bill?
A. Using 1kw cloth iron 2 hours a day
B. effectively lighting 02kw lamp 4 hours a day
C. using 1.5 kW cooks top 2 hours a day
D. using 0.5 kW water heater 2 hours a day
45. Cable specially designed for bringing supply in to a building as service
entrance conductor is
A. Underground feeder cable
B. Armored cable
C. Nonmetallic sheathed cable
D. service entrance cable
46. What makes a lump type contract different from bill of quantities type
contract?
A. Critical path Analysis is common and only used in lump type contract
B. In a lump type contract the estimator has to organize specific category
only
C. Measured work from bill of quantities contract is common contract
D. In a lump type contract the estimatortake all the quantities from the
drawing
47. …………….. Trucking is used in office where the service can be sited on the
perimeter
A. Bus bar
B. compartmented
C. Bench
D. Skirting
48. The loss due to aging of light source in illumination study considered as
………………. And its value ranges from………………
A. Coefficent of utiizatationfrom 1-2
B. Deprecation factor from 0.5-0.6
C. Illumination intensity fron 2-3
D. Maintenance factor from 0.6-08
49. Which type of lighting is used for playing fields and sport events?
A. Street lighting
B. Residential lighting
C. Flood lighting
D. Interior lighting The correct answer is C) Flood lighting.
50. Maximum number of single core 2.5mm2 wire in 16mm diameter conduit is?
A. 5
B. 6
C. 2
D. 10
51. According to EBC code 10 the color of cable for a three phase 4 wire system
A. Black. Black, Brown and blue
B. Blue, Red, Green and White
C. Green, Yellow, Red and Black
D. Red, Yellow, Blue and Black
According to the Electrical Wiring Regulations (EBC Code 10) for a three-
phase, four-wire system, the standard color coding for the cables is:
- Red - Phase 1
- Yellow - Phase 2
- Blue - Phase 3
- Black - Neutral
52. Polarity test in AC electrical installation helps to;
A. Know earthing loop impedance
B. Identify short circuit
C. prevent risk of electric shock
D. Show insulation resistance
53. Total Opposition to the current flow when fault arises due breakage of
insulation.
A. Reactance of a circuit
B. Earth leakage circuit breaker
C. Earth loop impedance of a circuit
D. Capacitance value of a circuit
54. To reduce voltage drop
A. Increase cable size
B. Decrease voltage rate
C. Minimize designed current
D. Increase customer load .
55. What will be fault finding road if security alarm fails to operate?
A. Check sensor operation of the system
B. Analyze the rating of voltage in the system
C. Check protection unit of high voltage system
D. Check the flow of current in the system
56. Which step considered first before preparing wiring estimation for house?
A. Collect the supply service from electricity board
B. Collect the Data from consumer like light, fan, and power point required
C. Collect the required wiring accessories and materials
D. Prepare the wiring layout
57. the most basic hand tools for electrician is;
A. Combination plier, screw drivers and knife
B. Chisel, measuring instrument and wrench
C. Caliper, screw driver and cutter
D. Engineers rule, caliper and hammer
58. After you isolate main power to test insulation resistance of new installation
A. All lamps and switches are in a proper place with power
B. All lamps out and continuity could be checked by meager
C. It is not possible to check insulation resistance between conductors
D. The phase and neural are shunted and take one terminal of meager
59. The common most abundant length of lightning arrestor of residential
building.
A. 3 Meter and 40 mm diameter alloy of brass
B. Meter and 35mm diameter steel made
C. 1 Meter and 25 mm diameter copper made
D. 5 Meter and 25 mm diameter aluminum made
60. The first step in the design of lighting is;
A. Select the lighting equipment
B. Identify the equipment
C. Determine the method of lighting
D. Calculate the lighting parameters
61. What does it mean ergonomic requirement to perform computer operation?
A. Gives idea about part of computer/hard ware
B. Indicates comfort ability in performing operation
C. Signifies computer company profile /experience
D. It clarifies the computer operation /
62. The maximum permissible load in a lighting sub-circuit is……………….
A. 800 watt
B. 1250 watt
C. 600 Watt
D. 1000 Watt
63. At what condition the earth leakage circuit breaker operates?
A. When leakage current not return by neutral conductor
B. When there is under voltage in the overall system
C. When neutral wire detached from supply
D. When a supply system becomes open
64. To read an accurate measurement less than 0.01mm usually we use………….
A. Outside caliper
B. Engineers rule
C. Micro meter
D. Tape rule
65. The main advantage of village transformer with star connected customer
side.
A. To double existing power
B. To produce sufficient illumination
C. To get the neutral wire
D. To gain extra voltage
66. Advantage of potential multiple earthling supply system is:
A. Provides an effective earthling connection to customers
B. Higher earthling impedance excluding private electrode
C. Prepare higher voltage to consumer area
D. Eating become live if a break in E and N happens
67. Which of the following comes first while designing electrical wiring installation
A. Prepare earting system size
B. Prepare protection equipment size
C. prepare distribution board sizing
D. Calculating total load current
68. The diversity factor in an installed electrical installation is nearly 0.9 indicates:
A. Partially installed loads are connected
B. 90% installed loads are connected
C. All installed loads are connected
D. 90% installed load is disconnected
69. The unit of luminous intensity from light source is ………………
A. Hz
B. Candela
C. siemen
D. Lux The correct unit of luminous intensity from a light source is
Candela (cd).
70. The two main common elevator types:
A. Hydraulic, robotic or pneumatic type
B. Hydraulic and electric or cable driven
C. Ac motor or dc motor type only
D. Pneumatic and electric or robotic type
71. High sensitivity protection device used for safety of the person even without
ground and fault loop and as an additional protection for direct contact.
A. MCCB
B. RCD
C. ELCB
D. MCB The correct answer is B) RCD (Residual Current Device).
72 Classification of electricity supply system depending on the type of earthling
arrangement TNC-S on the load side implies?
Separate conductor for PE and N
Combined conductor for PE and N
Separate earthling of supply
Combined PEN conductor for earthling
73. Importance of starting system for large induction motor is……………
A. To increase starting power
B. To regulate starting voltage
C. To decrease starting current
D. To decrease starting voltage
74. In circuit protection technique, fusing factor is:
A. The ratio of nominal current to designed current
B. Way how to size resistance for residential installation
C. The ratio of fusing current to current rating of fuse
D. System of current grading for nominal current
75. Illumination is studied:
A. To set exact light source for different class
B. For assigning different volt for different class
C. To assign exact beauty paint for classes
D. To study and appreciate beauty of building
76. The main cause of earth fault in the branch circuitries.
A. Breakdown of insulation
B. Detachment of neutral wire
C. Under size circuit breaker
D. Cut of feeder wire
77. What is the full load current of 5 HP, 400V 3 phase induction motor
having the efficiency 80% and power factor of0.85?
A. 9.5 Amps
B. 6.9 Amps
C. 7.8 Amps
D.5.2 Amps
The correct answer is C) 7.8 Amps.
To calculate the full load current of a 5 HP, 400V, 3-phase induction motor with an
efficiency of 80% and a power factor of 0.85, we can use the following formula:
Full load current = (5 HP × 746 W/HP) / (√3 × 400V × 0.85 × 0.80)
Where:
- 5 HP is the motor's horsepower
- 746 W/HP is the conversion factor from horsepower to watts
- √3 is the square root of 3, which is used for 3-phase systems
- 400V is the line voltage
- 0.85 is the power factor
- 0.80 is the efficiency
Plugging in the values, we get:
Full load current = (5 HP × 746 W/HP) / (√3 × 400V × 0.85 × 0.80)
Full load current = (3730 W) / (548.64 V)
Full load current = 7.8 Amps
Therefore, the correct answer is C) 7.8 Amps.
