ISO 4190-1:1999(E)
ISO
Table 1 Class I, II and VI lifts Functional dimensions of cars
Dimensions in millimetres Parameter Rated speed vn Rated load (mass)
320 kg 450 kg 630 kg 1 000 kg 630 kg 800 kg 1 000 kg/ 1 275 kg 1 275 kg 1 600 kg 1 800 kg 2 000 kg
Lifts in residential buildings
General-purpose lifts
Intensive-use lifts
Height of car, h4 Height of car door and landing doors, h3 Pit depth a, d3 0,40 m/s b 0,63 m/s 1,00 m/s 1,60 m/s 2,00 m/s 2,50 m/s 3,00 m/s 3,50 m/s 4,00 m/s d 5,00 m/s d 6,00 m/s d Headroom a, h1 0,40 m/s b 0,63 m/s 1,00 m/s 1,60 m/s 2,00 m/s 2,50 m/s 3,00 m/s 3,50 m/s 4,00 m/s d 5,00 m/s d 6,00 m/s d
a b c d Some countries require additional headroom (h1) and pit depth (d3). For hydraulic lifts only. Non-standard configuration. Assumes advantages taken of reduced stroke buffering. c c c 3 600 3 600 3 700 c c c 2 000
2 200
2 300 2 100 c
2 400
1 400 1 400
c 1 600 1 750 2 200 c c 1 750 2 200 3 200 3 400 c 3 800 3 800 4 000 c
3 800 4 000 c c
4 200 4 200 4 400
3 800 4 300 5 000
5 000
5 200
5 500 5 500
5 700 5 700 5 700 6 200
10
ISO
ISO 4190-1:1999(E)
Table 2 Class I, II and VI lifts Machine room dimensions
Dimensions in millimetres Rated load (mass) Rated speed, 320 kg to 630 kg b4 d4 800 kg to 1 000 kg b4 d4 1 275 kg to 1 600 kg b4 d4 1 800 kg to 2 000 kg b4 d4
vn
m/s Machine room for electric lifts 0,63 to 1,6 2,0 to 3,0 3,5 to 6,0 Machine room for hydraulic lifts a a 0,4 to 1,0
2 500
3 700
3 200 2 700 3 000
4 900 5 100 5 700
3 200 3 000 3 000
4 900 5 300 5 700
3 000 3 300 3 300
5 000 5 700 5 700
Width or depth of well
2 000 mm for lifts in residential buildings
Non-standard configuration for general-purpose or intensive-use lifts
Site conditions and national regulations may require different machine room dimensions (b4, d4, h2).
Table 3 Class III lifts (Health-care lifts) Functional dimensions
Parameter Rated speed vn m/s Car Car door and landing doors Pit depth, d3 0,63 1,00 1,60 2,00 2,50 Headroom, h1 0,63 1,00 1,60 2,00 2,50 Machine room a 0,63 to 2,50
a b
Rated load (mass)
1 275 kg 1 600 kg 2 000 kg 2 500 kg
Height, h4 Height, h3
(mm) (mm)
2 300 2 100 1 600 1 700 1 900 2 100 2 500 4 400 4 400 4 400 4 600 5 400 4 600 4 600 4 600 4 800 5 600 27 3 200 5 500 29 3 500 5 800 1 800 1 900 2 100 2 300
Surface, A Width b, b4 Depth b, d4
(m2) (mm) (mm)
25
Site conditions and national regulations may require different machine room dimensions (b4, d4, h2). b4 and d4 are minimum values. The actual dimensions shall provide a floor area at least equal to A.
11
ISO 4190-1:1999(E)
ISO
Key b1 Car width b2 Entrance width d1 Car depth h3 Entrance height h4 Car height 1) Decorative panels 2) Dropped ceiling
Figure 1 Car and entrance dimensions
12
ISO
ISO 4190-1:1999(E)
Key 1 2 3 4 5 Machine room Trap door Highest level served Lowest level served Vertical section of well and machine room
b3 b4 d2 d3 d4 h1 h2
Well width Machine room width Well depth Pit depth Machine room depth Headroom height Machine room height
a) For door details see Figure 1. b) It is necessary to have an access door to the machine room although this is not indicated on the sketch. c) See 2.3.12.
Figure 2 Electric lifts
13
ISO 4190-1:1999(E)
ISO
Dimensions in millimetres
Key 1 Machine room 2 Highest level served 3 Lowest level served 4 Vertical section of well and machine room
b3 b4 d2 d3 d4 h1 h2
Well width Machine room width Well depth Pit depth Machine room depth Headroom height Machine room height
a) For door details see Figure 1. b) It is necessary to have an access door to the machine room although this is not indicated on the sketch. c) See 2.3.12.
Figure 3 Hydraulic lifts
14
ISO
ISO 4190-1:1999(E)
Dimensions in millimetres
700 mm ENTRANCES Car height: Entrance height: 2 200 2 000
SERIES A 800 mm ENTRANCES Car height: Entrance height: 2 200 2 100
NOTES 1 Lifts suitable for speeds up to and including 2,5 m/s.
SERIES B 900 mm ENTRANCES Car height: Entrance height: 2 200 2 100
2 The selection of either series A or B depends on national regulations or market requirements. 3 Both series A and B fulfil handicap requirements and carry the symbol .
However, the selection of either an 800 mm or 900 mm door is subject to individual national regulations. 4 Even though counterweights are shown in the diagrams, the dimensions apply to all lifts irrespective of the drive system. a) Dimensions of stretcher 600 mm 2 000 mm.
Figure 4 Class I Residential lifts
15
ISO 4190-1:1999(E)
ISO
Dimensions in millimetres
Car height: Entrance height: 2 200 2 100 Car height: Entrance height: 2 300 2 100
SERIES A 800 mm ENTRANCES
SERIES B 900 mm ENTRANCES
SERIES C 1 100 mm ENTRANCES
NOTES 1 Lifts suitable for speeds up to and including 2,5 m/s. (When higher speeds are used, add 100 mm to the well width and depth.) 2 The selection of either series A, B or C depends on national regulations or market requirements. 3 Series A, B and C fulfil handicap requirements and carry the symbol .
However, the selection of either an 800 mm or 900 mm door is subject to individual national regulations. 4 Lifts marked thus
* allow full manuvrability of a wheelchair.
(For countries where the minimum requirement is that of full manuvrability.)
Figure 5 Class I General-purpose lifts
16
ISO
ISO 4190-1:1999(E)
Dimensions in millimetres
Car height: Entrance height:
2 400 2 100
NOTES 1 Lifts suitable for speeds 2,5 m/s up to and including 6,0 m/s because of having larger well sizes. 2 Lift marked thus
* allow full manuvrability of a wheelchair.
(For countries where the minimum requirement is that of full manuvrability.) a) Only for lifts with 1 275 kg rated load and 2,50 m/s rated speed (see Figure 5).
Figure 6 Class VI Intensive-use lifts
17
ISO 4190-1:1999(E)
ISO
Dimensions in millimetres
Car height: Entrance height:
2 300 2 100
NOTES 1 Lifts suitable for speeds up to and including 2,5 m/s. 2 Well dimensions shown in brackets are valid for hydraulic lifts. 3 Lifts marked thus
* allow full manuvrability of a wheelchair.
(For countries where the minimum requirement is that of full manuvrability.) 4 Even though counterweights are shown in the diagrams, the dimensions apply to all lifts irrespective of the drive system.
a) Bed dimensions 900 mm 2 000 mm. b) Bed dimensions 1 000 mm 2 300 mm. c) Bed dimensions 1 000 mm 2 300 mm, with additional instruments. Figure 7 Class III Health-care lifts
18
