Technical Support - Instruction

CP SB1 Self check

Author
Simon Morscher E-Mail: support@omicronenergy.com

Date
February 12, 2018

Related OMICRON Product

CPC100, CP SB1, PTM

Version
v1.0

Document ID
TSI_1508_CP_SB1_CP_SB1_Self_check_ENU

opp[Type here]
Table of Content

1 Scope of instruction .............................................................................................................................. 3

2 Step by Step Instructions - PTM .......................................................................................................... 4
2.1 CP SB1 self-check Job import........................................................................................................ 4
2.2 TTR Prim-Sec ................................................................................................................................. 5
2.3 RWinding Prim ................................................................................................................................ 6
2.4 RWinding Sec ................................................................................................................................. 8
3 Step by Step Instructions – CPC100 ................................................................................................... 9
3.1 CP SB1 self-check template ........................................................................................................... 9
3.2 TTR Prim-Sec ............................................................................................................................... 10
3.3 RWinding Prim .............................................................................................................................. 12
3.4 RWinding-Sec ............................................................................................................................... 13
4 Support ................................................................................................................................................. 15

Please use this note only in combination with the related product manual which contains several important safety
instructions. The user is responsible for every application that makes use of an OMICRON product.

OMICRON electronics GmbH including all international branch offices is henceforth referred to as OMICRON.

© OMICRON 2018. All rights reserved. This application note is a publication of OMICRON.
All rights including translation reserved. Reproduction of any kind, for example, photocopying, microfilming, optical
character recognition and/or storage in electronic data processing systems, requires the explicit consent of OMICRON.
Reprinting, wholly or in part, is not permitted.
The product information, specifications, and technical data embodied in this application note represent the technical
status at the time of writing and are subject to change without prior notice.
We have done our best to ensure that the information given in this application note is useful, accurate and entirely
reliable. However, OMICRON does not assume responsibility for any inaccuracies which may be present.
OMICRON translates this application note from the source language English into a number of other languages. Any
translation of this document is done for local requirements, and in the event of a dispute between the English and a non-
English version, the English version of this note shall govern.

@ OMICRON Page | 2
1 Scope of instruction

In case you suspect a problem with your CP SB1 device, it is possible to make some tests and save them.
Afterwards you can send these files via E-Mail to the OMICRON Technical Support.
This helps the support team finding a faster solution for the problem. Please also provide an error
description and serial number of the devices.

You can do the test either with the PTM (Omicron Primary Test Manager) or with the CPC100.

The check consists of three tests in order to check all HV and LV connections, as well as the tap control
(up/down):

 TTR Prim-Sec
 DC Winding Resistance Prim
 DC Winding Resistance Sec

@ OMICRON Page | 3
2 Step by Step Instructions - PTM

2.1 CP SB1 self-check Job import

Please find enclosed the Job for the test. (CP_SB1_self_check.ptm)
The job can be imported with a double click on the .ptm file.

Figure 1

Start the job called CP SB1 Selfcheck with a double click, afterwards you see the three tests on the left hand
side.

Figure 2

Please click on the first test (Turns Ratio Prim-Sec).

@ OMICRON Page | 4
2.2 TTR Prim-Sec
Connect the CP SB1 and the CPC100 according to Figure 3.

Figure 3

Check the settings according to Figure 4 and start the measurement, afterwards compare the results with
Figure 5 The Ratio dev field should be near 0% (±0.1%).

Figure 4

@ OMICRON Page | 5
Results:

Figure 5

2.3 RWinding Prim

Connect the CP SB1 and the CPC100 according to Figure 6. The DC Winding resistance Prim test should
show only the resistance of the test leads and contact resistance, if they are stacked upon each other on the
neutral point.
The test is configured with a tap changer (OLTC) with two taps in order to verify the function of the tap
control contacts for the up and down direction switching process. The function can be checked with a
multimeter during the switching process.

Figure 6

@ OMICRON Page | 6
Check the settings according to Figure 7 and start the measurement, afterwards compare the results with
Figure 8. The resistance should be in the range of a few mΩ.

Figure 7

Results:

Figure 8

@ OMICRON Page | 7
 2.4 RWinding Sec
Connect the CP SB1 and the CPC100 according to Figure 9.

Figure 9

Check the settings according to Figure 10 and start the measurements, afterwards compare the results with
Figure 11. The resistance should be in the range of a few mΩ.

Figure 10

@ OMICRON Page | 8
 Results:

Figure 11

3 Step by Step Instructions – CPC100

3.1 CP SB1 self-check template

Please find enclosed the template for the test (CP_SB1_self_check.xml). You can copy the template via
OMICRON Devices which is located on your Desktop, or via USB memory stick which is provided with the
CPC 100.

Figure 12

Double click on the serial number of CPC 100 you want to copy the template to.

Figure 13

Copy the .xml file into the Test folder which is attached in the e-mail.

@ OMICRON Page | 9
 CP_SB1_self_check.xml

Figure 14

Afterwards load the test from the file operations view on the CPC 100.

3.2 TTR Prim-Sec

Connect the CP SB1 and the CPC100 according to Figure 15.

Figure 15

@ OMICRON Page | 10
Check the settings according to Figure 16 and start the measurement, afterwards compare the results with
Figure 17. The Ratio dev field should be near 0% (±0.1%).

Figure 16

Results:

Figure 17

@ OMICRON Page | 11
 3.3 RWinding Prim
Connect the CP SB1 and the CPC100 according to Figure 18. The DC Winding resistance Prim test should
only show the resistance of the test leads and contact resistance if they are stacked upon each other on the
neutral point.
The test is configured with a tap changer (OLTC) with two taps in order to verify the function of the tap
control contacts for the up and down direction switching process. The function can be checked with a
multimeter during the switching process.

Figure 18

Check the settings according to Figure 19 and start the measurement, afterwards compare the results with
Figure 20. The resistance should be in the range of a few mΩ.

Figure 19

@ OMICRON Page | 12
Results:

Figure 20

3.4 RWinding-Sec
Connect the CP SB1 and the CPC100 according to Figure 21.

Figure 21

@ OMICRON Page | 13
Check the settings according to Figure 22 and start the measurement, afterwards compare the results with
Figure 23. The resistance should be in the range of a few mΩ.

Figure 22

Results:

Figure 23

@ OMICRON Page | 14
4 Support
For any further inquiries or questions regarding these instructions, please contact
your regional OMICRON Service Center. Information can be obtained from below.

24/7 Technical Support – Get Support

www.omicronenergy.com/support

At our technical support hotline, you can reach well-educated technicians for all
of your questions. Around the clock – competent and free of charge.

Make use of our 24/7 international technical support hotline:

Americas: +1 713 830-4660 or +1 800-OMICRON
Asia-Pacific: +852 3767 5500
Europe / Middle East / Africa: +43 59495 4444

Additionally, you can find our Service Center or Sales Partner closest to you at
www.omicronenergy.com.

Customer Area – Stay Informed

www.omicronenergy.com/customer

The customer area on our website is an international knowledge exchange platform.

Download the latest software updates for all products and share your own experiences in
our user forum.
Browse through the knowledge library and find application notes, conference papers, articles
about daily working experiences, user manuals and much more.

OMICRON Academy – Learn More

www.omicronenergy.com/academy

Learn more about your product in one of the training courses offered by the OMICRON
Academy.

OMICRON electronics GmbH, Oberes Ried 1, 6833 Klaus, Austria, +43 59495

@ OMICRON Page | 15
OMICRON is an international company serving the electrical power
industry with innovative testing and diagnostic solutions. The application of
OMICRON products provides users with the highest level of confidence in
the condition assessment of primary and secondary equipment on their
systems. Services offered in the area of consulting, commissioning,
testing, diagnosis, and training make the product range complete.
Customers in more than 140 countries rely on the company's ability to
supply leading edge technology of excellent quality. Broad application
knowledge and extraordinary customer support provided by offices in
North America, Europe, South and East Asia, and the Middle East,
together with a worldwide network of distributors and representatives,
make the company a market leader in its sector.

For addresses of OMICRON offices with customer service

centers, regional sales offices or offices for training,
consulting and commissioning please visit our web site.
@ OMICRON Page | 16

www.omicronenergy.at