MAHSR - PACKAGE NO.

C - 6
LOGO Project for Construction of
Mumbai-Ahmedabad High Speed Rail

DESIGN CERTIFICATE
(Design not developed from Standard Design)

This Design Certificate refers to Submission No. which comprises of

Design Package No: 1/2/3/4 Design developed from: Basic Designs Others

Design Stage Inception Report Technical Design

As Built Construction Design

Documents in respect of :

Pull-out test documents forM10 Stud using Fosroc Lokfix E77 chemical

.
Documents for which a Notice of No Objection has previously been issued and which are of
relevance to this Submission are listed in Section B below.

DESIGNER’S STATEMENT

We certify that the design detailing of the Works, as shown and described in the drawings
and documents listed in Section A below,
1) has been designed by us and complies with the Employer's Requirements and all other requirements
of the Contract;
2) has been confirmed as complete, adequate and valid for the design through an in-house design and QA check

3) includes all necessary and required approvals (e.g. from Local Authorities or agencies, etc.) relating
to the design. Copies of such approvals are annexed in Section C below;
4) all effects of the design comprising the submission on, or from, the design of adjacent or other parts
of the Works and Interfacing Contracts have been fully taken into account in the design;

Signed by ‘Authorised Representative’ (Designer)

Name: Rajiv Kannan Date: September 19, 2024

Position / Designation: SR. ENGINEERING MANAGER

# Sensitivity: Unclassified
Fosroc® Lokfix E77
(supersedes Lokfix E75)

High performance pure epoxy 3:1 resin car- ■ Waterproof, protecting the embedded fixing from corro-
tridge system, for anchoring reinforcement
sion and water penetration into the substrate.
and fixings into a variety of substrates.
■ Extended gel times allow for more complex procedures

■ Fire rated up to 2 hours*

■ 24 month shelf life

*Consult Fosroc technical department for specific data.

Description

Lokfix E77 is a two-component Epoxy anchoring material,

supplied in 3:1 ratio side-by-side cartridges with a static
mixer nozzle. When applied it sets and cures to firmly se-
cure a variety of steel fixings into concrete and solid ma-
sonry substrates.
Uses
Other grades of Lokfix are also available
For concrete (solid, porous and light) and solid masonry. Lokfix E55/E45 Rapid curing resin anchor cartridge sys-
■ Accredited* for use in dry, wet and flooded concrete sub- tem based on styrene free vinylester for heavy /medium
strates, internal and external exposure. duty anchoring.

■ Can be used with cracked concrete Lokfix P, Lokfix S High strength polyester resin anchor
grout for non critical fixings.
■ Fixing of post installed reinforcement
Lokfix TR High strength carbon steel and Stainless Steel
■ Anchoring of threaded rod fixings threaded rods of various diameters in customized lengths.
■ Anchoring of internal threaded rod sleeves Specification Clause
■ Can be applied to a wide variety of fixing and rebar sizes The anchor grout shall be Fosroc Lokfix E77 cartridge sys-
■ For horizontal, vertical and overhead application tem. The Anchoring grout shall comply with EAD 330087-
00-0601, systems for post-installed rebar connections, and
■ C1 and C2 seismic resistance*
EAD 330499-01-0601 for anchoring fixings into cracked
Advantages and un-cracked concrete.

■ High durability: Tested to achieve 100 year design life* Standards Compliance
■ High Bond strengths for heavyweight fixings or economi- Lokfix E77 complies with the following standards:
cal design.
■ European approval to EAD 330499-01-0601, anchoring
■ No additional mixing equipment required in cracked and un-cracked concrete (which supersedes
ETAG 001 option 5) includes fire testing, (threaded rod
■ Does not apply expansive force to the substrate
only) to 120 minutes and C1 & C2 seismic approval.
■ Fixings can be spaced closer together than mechanical
■ European approval to EAD 330087-00-0601, for use in
anchors
post-installed rebar connections (supersedes EOTA
■ Enables fixings closer to edges than mechanical anchors TR 023).
■ Low VOC ■ Émissions dans l’air intérieur : A+
■ Re-usable by replacing sealing cap product may be kept ■ LEED compliant VOC Level
to the end of original shelf life.

■ Tested with diamond drilled bore holes*

Page 1
Fosroc® Lokfix E77
**The stated curing time is for dry conditions. In wet/damp
conditions, the curing time will double.

Be aware that the substrate temperature can vary signifi-

cantly from the ambient temperature.

Chemical resistance

Lokfix E77 has resistance to a wide variety of chemicals.

*Consult Fosroc technical department for specific data.

Material Properties Design Criteria

Table 1 — Material Properties Assistance and qualification

Table 2 — Lokfix E77 Gel & Dry Curing Times. Design of fixings and reinforcement must be undertaken by
suitably qualified personnel with understanding of the con-
Compressive Strength (EN196-1) >110 MPa
struction and use of the structure, the use of the fixing, as
Flexural Strength (EN196-1) >60MPa well as being in compliance with local legislation.

E Modulus (ISO 527-2) >6000 MPa In applications where fixings or rebar must be designed
and applied in compliance with the requirements of the
Axial Tensile Strength (ISO 527-2) >40
relevant ETA and EAD, designers should consult the rele-
Shore A Hardness (ISO 868) >90 vant Fosroc accreditation documents.

Shore D Hardness (ISO 868) >85 Fosroc provides software which may be used to aid design,
available at [Link] or through your local technical
Density ~1.5kg/L
office.
Temporary service temp. (<24h) -40°C to +72°C

Permanent service temp. (>24h) Note tables 3, 4 and 5 suggestions for use and data provid-
-40°C to +50°C
ed has been selected based on following criteria: Compres-
Watertightness (EN12390-8) 0 mm sive class C20/25 dry/wet, un-cracked concrete, hammer
drilled or compressed air drilled. Rebar class Bst 500,
Electrical resistance (IEC93) 8 x1012 Ωm
threaded rod 8.8 class. 50 year design life with long/short
Thermal Conductivity (EN993-15) 0.50W/m.K term service temps maximums of +25/+40°C. Calculations
performed to comply with EN1992-4 (2018).
Substrate Gel Time **Dry Curing
All values in mm unless otherwise stated.
Temp. (mins) Time (hrs) * Data provided does not form part of the EAD
0ºC 90 144
For all other conditions including 100 year design life, in-
+10 ºC 60 28 creased concrete strength, fixings into solid masonry types,
fixings into cracked concrete, fixings subject to seismic
+20 ºC 30 12
conditions and post installation of reinforcement refer to the
+30 ºC 12 9 relevant method statement, EAD document or use the de-
sign software [Link], also available through your
+40ºC 8 4
local technical office.

For optimal use the cartridge temperature should be between

+5ºC to +40ºC. Note general storage conditions.

Page 2
 Fosroc® Lokfix E77
Table 3 - Rebar Anchoring Setting Parameters – details below

Rebar Anchor Size Ø8 Ø10 Ø12 Ø14 Ø16 Ø20 Ø24 Ø25 Ø28 Ø32 Ø36 
Ø40 

Min. Edge Distance Cmin 35 40 45 50 50 60 70 70 75 85 180 200

Min. Spacing Smin 40 50 60 70 75 90 120 120 130 150 180 200

Max. Embedment Depth hef,, max 160 200 240 280 320 400 480 500 560 640 720 800

Min. Embedment Depth hef,, min 60 60 70 75 80 90 96 100 112 128 144 240
hef +30mm
Min. Part Thickness hmin ≥100mm hef +2d0

Min. Drill Diameter D0, min 10 12 14 18 20 25 30 30 35 40 45 50

Max. Drill Diameter D0, max 12 14 16 18 20 25 32 32 35 40 45 50

Table 4 - Threaded Rod Anchoring Setting Parameters -details below

Anchor Size M8 M10 M12 M16 M20 M24 M27 M30 M33 
M36 
M39 
M42 
M48 

Min. Edge Distance Cmin 35 40 45 50 60 65 75 80 165 180 195 210 240

Min. Spacing Smin 40 50 60 75 95 115 125 140 165 180 195 210 240

Max. Embedment Depth hef,ma 160 200 240 320 400 480 540 600 660 720 780 840 960

Min. Embedment Depth hef,mi 60 60 70 80 90 96 108 120 132 144 156 168 192

Min Part Thickness hmin

hef +30mm ≥100mm hef +2d0

Drill Diameter d0 10 12 14 18 22 28 30 35 38 42 45 52 60

Max. Installation Torque Tinst. 10 20 40 60 100 170 250 300 330 360 390 460 550

Table 5 - Example Fixing loads

Fixing diameter 8 10 12 14 16 20 24 25 27 28

Embedment depth hef, 80 90 110 115 125 170 210 210 250 250

Edge distance C 120 135 165 173 188 255 315 315 375 375

Spacing S 240 270 330 345 375 510 630 630 750 750

Tension load for Threaded rod (kN) 13.8 20.0 27.0 - 32.7 51.9 71.3 - 92.6 -

Tension load for rebar (kN) 14.3 20.0 27.0 28.9 32.7 51.9 68.8 71.3 - 92.6

Fixing diameter 30 32 33 
36 
39 
40 
42 
48  Note: Greater/lesser
loads per fixing are
Embedment depth hef, 270 270 320 350 380 380 420 480 possible depending
on embedment depth
Edge distance C 405 405 480 525 570 570 630 720 and other factors.
Consult Fosroc tech-
Spacing S 810 810 960 1050 1140 1140 1260 1440 nical for advice.

Tension load for Threaded rod (kN) 103.9 - 111.7 127.8 144.6 - 168.0 205.3 * Data provided does
not form part of the
Tension load for rebar (kN) - 103.9 - 127.8 - 144.6 - - EAD

Page 3
Fosroc® Lokfix E77
Product Installation Unscrew the fixing cap from the cartridge.

Full details are available in the application method statement, Screw the static mixer nozzle onto the cartridge. Place the
a copy of which may be obtained from your local Fosroc cartridge into the application gun.
technical department. Pull the trigger to extrude the Lokfix E77.
The following methodology is for installation into solid sub- Important: extrude the initial material until the colour be-
strates such as reinforced concrete. For other substrates or comes red and consistent. This typically takes two or three
fixings please request a separate method statement. full squeezes. Discard material that is streaky in colour.
Hole Formation and Preparation Insert the nozzle to the back of the hole and pump the Lokfix
Drill hole with percussive drill or compressed air drill ensuring material gently pulling back until the hole is ⅔ to ¾ full. En-
sides of the concrete are rough. If using a hollow drill bit sure there are no voids in the resin. If the hole is too deep
system, additional hole preparation is not generally neces- for the nozzle to reach the back, use an extension nozzle.
sary. If using diamond drill, the hole must be flushed with In wide/overhead holes a piston plug will help reduce slump
clean water, cleaned with a wire brush and flushed again and ensure a void-free application. This is particularly rec-
before using the cleaning process described below. ommended for holes above 16mm diameter.
If rebar is encountered, immediately stop drilling and seek Observing the product gel time, insert the fixing into the hole
the advice of the designing engineer. using a gentle twisting motion. Ensure the fixing is inserted
Clean holes immediately prior to installation of fixings to to the required depth and is held straight until the resin sets.
avoid them becoming re-contaminated. There should be some extrusion of the Lokfix material from
the hole which indicates that there is full embedment.
Standing water in the hole shall be removed prior to prepara-
tion. Using compressed air, insert the nozzle to the back of Do not load or apply tension to the fixing until the product
the hole and blow out 2 times. fixing time has been observed, see table 2 .

Insert a wire cleaning brush to the bottom of the hole and Do not over-tighten fixings. Observe maximum installation
brush out 2 times. Cleaning brush should be at least 0.5mm torque as stated in table 4.
wider than diameter of drill hole. If the cartridge is to be re-used, remove the mixing nozzle
Using compressed air, insert the nozzle to the back of the and re-apply the cap. When using again, a new mixing noz-
hole and blow out an additional 2 times. zle will be required, ensure product is pre-extruded and of
consistent colour before use.
If dust is still present, repeat the process until no further dust
is visible. Cleaning

Ensure the drill bit and the cleaning brush are of suitable Uncured resin should be removed from tools and equipment
diameter for the fixing used. Consult tables 3 and 4 for spe- using Nitoflor SOL immediately after use.
cific diameters.
Estimating
Fixings Preparation
Supply
Fixings shall be free from rust, paint, grease and contami-
nants which will interfere with the bond. Lokfix E77 is supplied in box containing 12 no’s of 585 ml
cartridges, each supplied with a mixer nozzle.
Mark the required depth on the fixing.
Fosroc may also supply:
Installation
■ Lokfix TR: High strength carbon steel and Stainless
Lokfix E77 requires a special 3:1 application gun, this can be
Steel threaded rods of various diameters in customized
supplied by Fosroc.
lengths.

■ Lokfix application gun, suitable for 440 and 585ml sizes.

■ Various sized steel brushes, to clean the hole.

Page 4
Fosroc® Lokfix E77
■ Extension nozzle, essential where the embedment depth Further Information
is greater than 190mm in various lengths.
Further product information is available including, EAD certifi-
■ Piston plugs, required where the hole diameter is >18mm cation, SDS, Method Statements and calculation software.
or where embedment depth is >250mm. Must be used This can be found at [Link] or by contacting your
with an extension nozzle. local Fosroc office.

■ Spare mixer nozzles, required if a cartridge is to be re-

Precautions
used.
Health & Safety
Yield
The following calculation of theoretical consumption may be Observe the information provided on the relevant SDS.
used. Factors such as over-drilling, extrusion from bolt hole,
initial gun extrusion and some wastage should also be con-
sidered.

Theoretical Consumption:
( radius cm hole2 -  radius cm bolt2) x hole length cm =
consumption ml.

Practical Consumption:
 radius cm hole2 x hole length cm x 0.67= consumption ml.

Limitations

Load calculations should always be undertaken by a qualified

engineer.
*Consult Fosroc technical department for specific data.
For designing under conditions where extended service life,
seismic forces or fire is a consideration, please consult the ®Fosroc and Lokfix are registered trademarks of Fosroc
relevant certification to make suitable adjustments for load- International Limited
ing.

Lokfix E77 may stain natural or decorative stone. Please

check suitability before using for such applications.

Where faster gelling or setting times are required, consider

using Lokfix E55 or Lokfix E45T.

Storage

Lokfix E77 Cartridges have a maximum shelf life of 24

months when kept in a dry warehouse at between +5 to
+35ºC. It is possible to allow cartridge temperature to raise to
+40ºC immediately prior to application.

Page 5
 Fosroc® Lokfix E77
Notes

……………………………………………………………………………………………………………………………………………………………………………………………………

……………………………………………………………………………………………………………………………………………………………………………………………………

……………………………………………………………………………………………………………………………………………………………………………………………………

……………………………………………………………………………………………………………………………………………………………………………………………………

……………………………………………………………………………………………………………………………………………………………………………………………………

……………………………………………………………………………………………………………………………………………………………………………………………………

……………………………………………………………………………………………………………………………………………………………………………………………………

……………………………………………………………………………………………………………………………………………………………………………………………………

……………………………………………………………………………………………………………………………………………………………………………………………………

……………………………………………………………………………………………………………………………………………………………………………………………………

……………………………………………………………………………………………………………………………………………………………………………………………………

……………………………………………………………………………………………………………………………………………………………………………………………………

……………………………………………………………………………………………………………………………………………………………………………………………………

……………………………………………………………………………………………………………………………………………………………………………………………………

……………………………………………………………………………………………………………………………………………………………………………………………………

……………………………………………………………………………………………………………………………………………………………………………………………………

Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for the Supply
of Goods and Services, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that any advice, recommendation,
specification of information it may give is accurate and correct, it cannot, because it has no direct or continuous control over where or how its
products are applied, accept any liability either directly or indirectly arising from the use of its products, whether or not in accordance with any
advice, specification, recommendation of information given by it.

Fosroc Chemicals Telephone: Fax: email:

(India) Pvt. Ltd. +91 80 42521900 +91 22281510 enquiryindia@[Link]

Head Office
Embassy Point
No:150, 2nd Floor,
Infantry Road,
Bangalore — 560001. Regional Offices
Chennai Mumbai Noida Kolkata
Hills Center Old No.5, New No.9 MBC Park, 12th floor, Office No, 12B, Unit No. 601, Highway Tower-II, 304, Jodhpur Park,
3rd Cross Street, Jeth Nagar, “D” Block, Near G Corp/Hyper City, A-13/2, 6th Floor, Sector — 62, Kolkata—700068.
Raja Annamalaipuram, Kasarwadawali, Ghodbunder Road, Gautam Buddha Nagar, Tel: +91 33 65343188
Chennai — 600028. Thane (West) - 400615. Noida — 201309. Fax: 033 2499 0280
Tel: +91 44 24899949-94 Tel: +91 22 62296800 Tel: +91 120 6121900
Fax: 044 2489641 Fax: 022 62296809.

[Link]
Page 6 INDIA/2021/0340/A
Revision date: 25/08/2021 Revision: 0

SAFETY DATA SHEET

LOKFIX E77 Part A

SECTION 1: Identification of the substance/mixture and of the company/undertaking

1.1. Product identifier

Product name LOKFIX E77 Part A

1.2. Relevant identified uses of the substance or mixture and uses advised against
Identified uses Adhesive mortar for fastening elements. A-Component. For professional use.

1.3. Details of the supplier of the safety data sheet

Supplier Fosroc Chemical (India) Pvt. Ltd
Embassy Point, No 150, 2nd Floor,
Infantry Road,
Bangalore - 560001
+91 80 2355 1500/ 4252 1900
+91 80 2355 1510

1.4. Emergency telephone number

Emergency telephone +91 80 2355 1500/ 4252 1900

SECTION 2: Hazards identification

2.1. Classification of the substance or mixture

Classification (EC 1272/2008)
Physical hazards Not Classified

Health hazards Skin Irrit. 2 - H315 Eye Irrit. 2 - H319 Skin Sens. 1 - H317

Environmental hazards Aquatic Chronic 2 - H411

Human health May cause skin sensitisation or allergic reactions in sensitive individuals.

2.2. Label elements

Hazard pictograms

Signal word Warning

Hazard statements H315 Causes skin irritation.

H319 Causes serious eye irritation.
H317 May cause an allergic skin reaction.
H411 Toxic to aquatic life with long lasting effects.

1/11
Revision date: 25/08/2021 Revision: 0

LOKFIX E77 Part A

Precautionary statements P264 Wash contaminated skin thoroughly after handling.

P273 Avoid release to the environment.
P280 Wear protective gloves/ protective clothing/ eye protection/ face protection.
P333+P313 If skin irritation or rash occurs: Get medical advice/ attention.
P337+P313 If eye irritation persists: Get medical advice/ attention.
P391 Collect spillage.

Contains 2,2'-[1-METHYLETHYLIDENE)BIS(4,1-PHENYLENEOXYMETHYLENE)]BISOXIRANE, 1,6

HEXANEDIOL DIGLYCIDYL ETHER

Supplementary precautionary P261 Avoid breathing dust.

statements P272 Contaminated work clothing should not be allowed out of the workplace.
P302+P352 IF ON SKIN: Wash with plenty of water.
P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove
contact lenses, if present and easy to do. Continue rinsing.
P321 Specific treatment (see medical advice on this label).
P332+P313 If skin irritation occurs: Get medical advice/ attention.
P362+P364 Take off contaminated clothing and wash it before reuse.
P501 Dispose of contents/ container in accordance with national regulations.

2.3. Other hazards

This product does not contain any substances classified as PBT or vPvB.

SECTION 3: Composition/information on ingredients

3.2. Mixtures

2,2'-[1-METHYLETHYLIDENE)BIS(4,1- 30-60%
PHENYLENEOXYMETHYLENE)]BISOXIRANE
CAS number: 1675-54-3 EC number: 216-823-5

Classification
Skin Irrit. 2 - H315
Eye Irrit. 2 - H319
Skin Sens. 1 - H317
Aquatic Chronic 2 - H411

1,6 HEXANEDIOL DIGLYCIDYL ETHER 10-30%

CAS number: 16096-31-4 EC number: 240-260-4

Classification
Skin Irrit. 2 - H315
Eye Irrit. 2 - H319
Skin Sens. 1 - H317
Aquatic Chronic 3 - H412

The Full Text for all R-Phrases and Hazard Statements are Displayed in Section 16.

SECTION 4: First aid measures

4.1. Description of first aid measures

General information Promptly remove any clothing that becomes contaminated. Get medical advice/attention if you
feel unwell.

Inhalation Move affected person to fresh air at once. If in doubt, get medical attention promptly.

Ingestion Do not induce vomiting. Rinse mouth thoroughly with water. Get medical attention.

2/11
Revision date: 25/08/2021 Revision: 0

LOKFIX E77 Part A

Skin contact After contact with skin, take off immediately all contaminated clothing, and wash immediately
with plenty of water. Get medical attention. Wash contaminated clothing before reuse.

Eye contact Rinse with water. Remove contact lenses, if present and easy to do. Continue rinsing.
Continue to rinse for at least 15 minutes. Get medical attention.

4.2. Most important symptoms and effects, both acute and delayed
Skin contact Causes skin irritation. May cause skin sensitisation or allergic reactions in sensitive
individuals.

Eye contact Causes serious eye irritation.

4.3. Indication of any immediate medical attention and special treatment needed
Notes for the doctor Treat symptomatically.

SECTION 5: Firefighting measures

5.1. Extinguishing media

Suitable extinguishing media Extinguish with foam, carbon dioxide, dry powder or water fog.

Unsuitable extinguishing Do not use water jet as an extinguisher, as this will spread the fire.
media

5.2. Special hazards arising from the substance or mixture

Hazardous combustion Toxic pyrolysis products Carbon monoxide (CO).
products

5.3. Advice for firefighters

Protective actions during In case of fire and/or explosion do not breathe fumes. Use water spray to reduce vapours.
firefighting Avoid the spillage or runoff entering drains, sewers or watercourses.

Special protective equipment Wear positive-pressure self-contained breathing apparatus (SCBA) and appropriate protective
for firefighters clothing.

SECTION 6: Accidental release measures

6.1. Personal precautions, protective equipment and emergency procedures

Personal precautions Wear protective gloves, eye and face protection. Avoid contact with skin, eyes and clothing.
Provide adequate ventilation.

6.2. Environmental precautions

Environmental precautions Avoid release to the environment. Avoid the spillage or runoff entering drains, sewers or
watercourses.

6.3. Methods and material for containment and cleaning up

Methods for cleaning up Collect spillage. Absorb in vermiculite, dry sand or earth and place into containers. For waste
disposal, see Section 13.

6.4. Reference to other sections

Reference to other sections For personal protection, see Section 8. For waste disposal, see Section 13.

SECTION 7: Handling and storage

7.1. Precautions for safe handling

Usage precautions For professional users only. Use only outdoors or in a well-ventilated area. Wear protective
clothing as described in Section 8 of this safety data sheet. Avoid contact with skin, eyes and
clothing. Do not eat, drink or smoke when using this product.

3/11
Revision date: 25/08/2021 Revision: 0

LOKFIX E77 Part A

7.2. Conditions for safe storage, including any incompatibilities

Storage precautions Keep only in the original container in a cool, well-ventilated place. Container must be kept
tightly closed when not in use. Avoid contact with oxidising agents. Keep away from food,
drink and animal feeding stuffs.

7.3. Specific end use(s)

Specific end use(s) The identified uses for this product are detailed in Section 1.2.

SECTION 8: Exposure controls/Personal protection

8.1. Control parameters

Additional advice on limit This mixture contains quartz filler which is firmly bound in the pasty component, and thus not
values freely available during use, so that a risk of dust inhalation is excluded. Exposure limit values
for respirable dusts are not relevant for this product.

2,2'-[1-METHYLETHYLIDENE)BIS(4,1-PHENYLENEOXYMETHYLENE)]BISOXIRANE (CAS: 1675-54-3)

DNEL Workers - Dermal; Short term systemic effects: 8.33 mg/kg/day

Workers - Inhalation; Short term systemic effects: 12.25 mg/kg/day
Workers - Dermal; Long term systemic effects: 8.33 mg/kg/day
Workers - Inhalation; Long term systemic effects: 12.25 mg/kg/day
Consumer - Dermal; Short term systemic effects: 3.571 mg/kg/day
Consumer - Oral; Short term systemic effects: 0.75 mg/kg/day
Consumer - Dermal; Long term systemic effects: 3.571 mg/kg/day
Consumer - Oral; Long term systemic effects: 0.75 mg/kg/day

1,6 HEXANEDIOL DIGLYCIDYL ETHER (CAS: 16096-31-4)

DNEL Workers - Inhalation; Long term systemic effects: 10.57 mg/m³

Workers - Inhalation; Long term local effects: 0.44 mg/m³
Workers - Dermal; Long term systemic effects: 6.0 mg/kg/day
Workers - Dermal; Long term local effects: 0.0226 mg/cm²

PNEC Fresh water; 0.0115 mg/l

marine water; 0.00115 mg/l
Sediment (Freshwater); 0.283 mg/kg
Sediment (Marinewater); 0.283 mg/kg

8.2. Exposure controls

Protective equipment

Appropriate engineering Provide adequate ventilation. Mechanical ventilation or local exhaust ventilation may be
controls required.

Eye/face protection Wear tight-fitting, chemical splash goggles or face shield.

Hand protection To protect hands from chemicals, gloves should comply with European Standard EN374. It is
recommended that gloves are made of the following material: Nitrile rubber. Thickness: > 0.7
mm The selected gloves should have a breakthrough time of at least 8 hours.

Other skin and body Wear protective clothing.

protection

4/11
Revision date: 25/08/2021 Revision: 0

LOKFIX E77 Part A

Hygiene measures Take off contaminated clothing and wash it before reuse. Wash contaminated skin thoroughly
after handling. Wash after use and before eating, smoking and using the toilet. Do not eat,
drink or smoke when using this product.

Respiratory protection If ventilation is inadequate, suitable respiratory protection must be worn. Wear a respirator
fitted with the following cartridge: Combination filter, type A2/P2.

SECTION 9: Physical and chemical properties

9.1. Information on basic physical and chemical properties

Appearance Solid. Paste.

Colour Beige.

Odour Characteristic.

pH Not determined.

Melting point Not determined.

Initial boiling point and range Not determined.

Flash point Not applicable.

Evaporation rate Not determined.

Flammability (solid, gas) Not determined.

Upper/lower flammability or Not determined.

explosive limits

Vapour pressure Not determined.

Relative density 1.45 @ 20°C

Solubility(ies) Insoluble in water.

Partition coefficient Not determined.

Auto-ignition temperature Not determined.

Decomposition Temperature Not determined.

Explosive properties Not considered to be explosive.

Oxidising properties Does not meet the criteria for classification as oxidising.

9.2. Other information

Other information No data available.

SECTION 10: Stability and reactivity

10.1. Reactivity
Reactivity See Section 10.3 (Possibility of hazardous reactions) for further information.

10.2. Chemical stability

Stability Stable at normal ambient temperatures.

10.3. Possibility of hazardous reactions

Possibility of hazardous The following materials may react violently with the product: Strong oxidising agents.
reactions

10.4. Conditions to avoid

5/11
Revision date: 25/08/2021 Revision: 0

LOKFIX E77 Part A

Conditions to avoid Avoid heat. Avoid exposure to high temperatures or direct sunlight.

10.5. Incompatible materials

Materials to avoid Oxidising agents.

10.6. Hazardous decomposition products

Hazardous decomposition No known hazardous decomposition products.
products

SECTION 11: Toxicological information

11.1. Information on toxicological effects

Toxicological effects Based on available data the classification criteria are not met.

Skin corrosion/irritation
Skin corrosion/irritation Causes skin irritation.

Serious eye damage/irritation

Serious eye damage/irritation Causes serious eye irritation.

Respiratory sensitisation
Respiratory sensitisation Based on available data the classification criteria are not met.

Skin sensitisation
Skin sensitisation May cause an allergic skin reaction.

Germ cell mutagenicity

Summary Based on available data the classification criteria are not met.

Carcinogenicity
Carcinogenicity Based on available data the classification criteria are not met.

Reproductive toxicity
Summary Based on available data the classification criteria are not met.

Specific target organ toxicity - single exposure

STOT - single exposure Based on available data the classification criteria are not met.

Specific target organ toxicity - repeated exposure

STOT - repeated exposure Based on available data the classification criteria are not met.

Aspiration hazard
Aspiration hazard Based on available data the classification criteria are not met.

Toxicological information on ingredients.

1,6 HEXANEDIOL DIGLYCIDYL ETHER

Acute toxicity - oral

Acute toxicity oral (LD₅₀ 2,190.0

mg/kg)

Species Rat

ATE oral (mg/kg) 2,190.0

Acute toxicity - dermal

Notes (dermal LD₅₀) LD₅₀ >2000 mg/kg, Dermal, Rat

6/11
Revision date: 25/08/2021 Revision: 0

LOKFIX E77 Part A

Acute toxicity - inhalation

Acute toxicity inhalation 0.035

(LC₅₀ vapours mg/l)

Species Rat

SECTION 12: Ecological information

Ecotoxicity Toxic to aquatic life with long lasting effects.

Ecological information on ingredients.

2,2'-[1-METHYLETHYLIDENE)BIS(4,1-PHENYLENEOXYMETHYLENE)]BISOXIRANE

Ecotoxicity Toxic to aquatic life with long lasting effects.

12.1. Toxicity
Ecological information on ingredients.

2,2'-[1-METHYLETHYLIDENE)BIS(4,1-PHENYLENEOXYMETHYLENE)]BISOXIRANE

Toxicity Very toxic to aquatic life with long lasting effects.

Acute aquatic toxicity

Acute toxicity - fish LC₅₀, 96 hours: 2 mg/l, Oncorhynchus mykiss (Rainbow trout)

Acute toxicity - aquatic EC₅₀, 48 hours: 1.8 mg/l, Daphnia magna

invertebrates

Acute toxicity - aquatic ErC50, 72 hours: 11 mg/l, Scenedesmus capricornutum (fresh water algae)
plants

Chronic aquatic toxicity

Chronic toxicity - aquatic NOEC, 21 days: 0.3 mg/l, Daphnia magna

invertebrates

1,6 HEXANEDIOL DIGLYCIDYL ETHER

Acute aquatic toxicity

Acute toxicity - fish LC₅₀, 96 hours: 30 mg/l, Oncorhynchus mykiss (Rainbow trout)

Acute toxicity - aquatic EC₅₀, 48 hours: 47 mg/l, Daphnia magna

invertebrates

12.2. Persistence and degradability

Persistence and degradability The product contains persistent (not readily degradable) substances. The other substances in
the product are expected to be readily biodegradable.

Ecological information on ingredients.

2,2'-[1-METHYLETHYLIDENE)BIS(4,1-PHENYLENEOXYMETHYLENE)]BISOXIRANE

Persistence and The product is not readily biodegradable.

degradability

Biodegradation - Degradation 12%: 28 days

OECD 302B

1,6 HEXANEDIOL DIGLYCIDYL ETHER

7/11
Revision date: 25/08/2021 Revision: 0

LOKFIX E77 Part A

Biodegradation - 71%: 28 days

OECD 301D

12.3. Bioaccumulative potential

Bioaccumulative potential Not determined.

Partition coefficient Not determined.

Ecological information on ingredients.

2,2'-[1-METHYLETHYLIDENE)BIS(4,1-PHENYLENEOXYMETHYLENE)]BISOXIRANE

Bioaccumulative potential Potentially bioaccumulating.

Partition coefficient log Pow: 3.24 Estimated value

1,6 HEXANEDIOL DIGLYCIDYL ETHER

Bioaccumulative potential BCF: 3.57,

Partition coefficient log Pow: 0.822

12.4. Mobility in soil

Mobility Insoluble in water.

Ecological information on ingredients.

2,2'-[1-METHYLETHYLIDENE)BIS(4,1-PHENYLENEOXYMETHYLENE)]BISOXIRANE

Mobility Low mobility.

Adsorption/desorption - Koc: Estimated value. 1800 - 4400 @ 20°C

coefficient

12.5. Results of PBT and vPvB assessment

Results of PBT and vPvB This product does not contain any substances classified as PBT or vPvB.
assessment

Ecological information on ingredients.

2,2'-[1-METHYLETHYLIDENE)BIS(4,1-PHENYLENEOXYMETHYLENE)]BISOXIRANE

Results of PBT and vPvB This substance is not classified as PBT or vPvB according to current EU criteria.
assessment

12.6. Other adverse effects

Other adverse effects None known.

SECTION 13: Disposal considerations

13.1. Waste treatment methods

General information Dispose of waste product or used containers in accordance with local regulations

Waste class 080409

150110

SECTION 14: Transport information

14.1. UN number
UN No. (ADR/RID) 3077

8/11
Revision date: 25/08/2021 Revision: 0

LOKFIX E77 Part A

UN No. (IMDG) 3077

UN No. (ICAO) 3077

UN No. (ADN) 3077

14.2. UN proper shipping name

Proper shipping name ENVIRONMENTALLY HAZARDOUS SUBSTANCE, SOLID, N.O.S. (EPOXY RESIN)
(ADR/RID)

Proper shipping name (IMDG) ENVIRONMENTALLY HAZARDOUS SUBSTANCE, SOLID, N.O.S. (EPOXY RESIN)

Proper shipping name (ICAO) ENVIRONMENTALLY HAZARDOUS SUBSTANCE, SOLID, N.O.S. (EPOXY RESIN)

Proper shipping name (ADN) ENVIRONMENTALLY HAZARDOUS SUBSTANCE, SOLID, N.O.S. (EPOXY RESIN)

14.3. Transport hazard class(es)

ADR/RID class 9

ADR/RID classification code M7

ADR/RID label 9

IMDG class 9

ICAO class/division 9

ADN class 9

Transport labels

14.4. Packing group

ADR/RID packing group III

IMDG packing group III

ICAO packing group III

ADN packing group III

14.5. Environmental hazards

Environmentally hazardous substance/marine pollutant

14.6. Special precautions for user

EmS F-A, S-F

ADR transport category 3

Emergency Action Code 2Z

Hazard Identification Number 90

(ADR/RID)

Tunnel restriction code (-)

14.7. Transport in bulk according to Annex II of MARPOL and the IBC Code

9/11
Revision date: 25/08/2021 Revision: 0

LOKFIX E77 Part A

Transport in bulk according to Not applicable.

Annex II of MARPOL 73/78
and the IBC Code

SECTION 15: Regulatory information

15.1. Safety, health and environmental regulations/legislation specific for the substance or mixture
EU legislation Regulation (EC) No 1907/2006 of the European Parliament and of the Council of 18
December 2006 concerning the Registration, Evaluation, Authorisation and Restriction of
Chemicals (REACH) (as amended).
Regulation (EC) No 1272/2008 of the European Parliament and of the Council of 16
December 2008 on classification, labelling and packaging of substances and mixtures (as
amended).
Commission Regulation (EU) No 453/2010 of 20 May 2010.

15.2. Chemical safety assessment

No chemical safety assessment has been carried out.

SECTION 16: Other information

Abbreviations and acronyms ADR: European Agreement concerning the International Carriage of Dangerous Goods by
used in the safety data sheet Road.
ADN: European Agreement concerning the International Carriage of Dangerous Goods by
Inland Waterways.
ATE: Acute Toxicity Estimate.
BCF: Bioconcentration Factor.
CAS: Chemical Abstracts Service.
DNEL: Derived No Effect Level.
EC₅₀: 50% of maximal Effective Concentration.
ErC50: the concentration of test substance which results in a 50% reduction in growth rate
relative to the control.
ICAO: Technical Instructions for the Safe Transport of Dangerous Goods by Air.
IMDG: International Maritime Dangerous Goods.
LC₅₀: Lethal Concentration to 50 % of a test population.
LD₅₀: Lethal Dose to 50% of a test population (Median Lethal Dose).
NOEC: No Observed Effect Concentration.
PBT: Persistent, Bioaccumulative and Toxic substance.
PNEC: Predicted No Effect Concentration.
REACH: Registration, Evaluation, Authorisation and Restriction of Chemicals Regulation
(EC) No 1907/2006.
RID: European Agreement concerning the International Carriage of Dangerous Goods by
Rail.
STP: Sewage treatment plant
vPvB: Very Persistent and Very Bioaccumulative.

Revision comments This is the first issue.

Revision date 25/08/2021

Revision 0

SDS number 29984

10/11
Revision date: 25/08/2021 Revision: 0

LOKFIX E77 Part A

Hazard statements in full H315 Causes skin irritation.

H317 May cause an allergic skin reaction.
H319 Causes serious eye irritation.
H411 Toxic to aquatic life with long lasting effects.
H412 Harmful to aquatic life with long lasting effects.

This information relates only to the specific material designated and may not be valid for such material used in combination
with any other materials or in any process. Such information is, to the best of the company's knowledge and belief, accurate
and reliable as of the date indicated. However, no warranty, guarantee or representation is made to its accuracy, reliability or
completeness. It is the user's responsibility to satisfy himself as to the suitability of such information for his own particular use.

11/11
Revision date: 25/08/2021 Revision: 0

SAFETY DATA SHEET

LOKFIX E77 Part B

SECTION 1: Identification of the substance/mixture and of the company/undertaking

1.1. Product identifier

Product name LOKFIX E77 Part B

1.2. Relevant identified uses of the substance or mixture and uses advised against
Identified uses Adhesive mortar for fastening elements. B-Component. For professional use.

1.3. Details of the supplier of the safety data sheet

Supplier Fosroc Chemical (India) Pvt. Ltd
Embassy Point, No 150, 2nd Floor,
Infantry Road,
Bangalore - 560001
+91 80 2355 1500/ 4252 1900
+91 80 2355 1510

1.4. Emergency telephone number

Emergency telephone +91 80 2355 1500/ 4252 1900

SECTION 2: Hazards identification

2.1. Classification of the substance or mixture

Classification (EC 1272/2008)
Physical hazards Not Classified

Health hazards Acute Tox. 4 - H302 Skin Corr. 1B - H314 Eye Dam. 1 - H318 Skin Sens. 1 - H317

Environmental hazards Aquatic Chronic 3 - H412

Human health May cause sensitisation or allergic reactions in sensitive individuals.

2.2. Label elements

Hazard pictograms

Signal word Danger

Hazard statements H302 Harmful if swallowed.

H314 Causes severe skin burns and eye damage.
H317 May cause an allergic skin reaction.
H412 Harmful to aquatic life with long lasting effects.

1/12
Revision date: 25/08/2021 Revision: 0

LOKFIX E77 Part B

Precautionary statements P273 Avoid release to the environment.

P280 Wear protective gloves/ protective clothing/ eye protection/ face protection.
P301+P330+P331 IF SWALLOWED: Rinse mouth. Do NOT induce vomiting.
P303+P361+P353 IF ON SKIN (or hair): Take off immediately all contaminated clothing.
Rinse skin with water or shower.
P333+P313 If skin irritation or rash occurs: Get medical advice/ attention.
P501 Dispose of contents/ container in accordance with national regulations.

Contains 2,2,4(or 2,4,4)-TRIMETHYLHEXANE-1,6-DIAMINE, 2,4,6-

TRIS(DIMETHYLAMINOMETHYL)PHENOL, m-PHENYLENEBIS( METHYLAMINE)

Supplementary precautionary P260 Do not breathe dust.

statements P261 Avoid breathing dust.
P264 Wash contaminated skin thoroughly after handling.
P270 Do not eat, drink or smoke when using this product.
P272 Contaminated work clothing should not be allowed out of the workplace.
P301+P312 IF SWALLOWED: Call a POISON CENTRE/doctor if you feel unwell.
P302+P352 IF ON SKIN: Wash with plenty of water.
P304+P340 IF INHALED: Remove person to fresh air and keep comfortable for breathing.
P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove
contact lenses, if present and easy to do. Continue rinsing.
P310 Immediately call a POISON CENTER/ doctor.
P321 Specific treatment (see medical advice on this label).
P362+P364 Take off contaminated clothing and wash it before reuse.
P363 Wash contaminated clothing before reuse.
P405 Store locked up.

2.3. Other hazards

This product does not contain any substances classified as PBT or vPvB.

SECTION 3: Composition/information on ingredients

3.2. Mixtures

2,2,4(or 2,4,4)-TRIMETHYLHEXANE-1,6-DIAMINE 30-60%

CAS number: 25620-58-0 EC number: 247-134-8 REACH registration number: 01-
2119560598-25-XXXX

Classification
Acute Tox. 4 - H302
Skin Corr. 1B - H314
Eye Dam. 1 - H318
Skin Sens. 1 - H317
Aquatic Chronic 3 - H412

2,4,6-TRIS(DIMETHYLAMINOMETHYL)PHENOL 5-10%
CAS number: 90-72-2 EC number: 202-013-9 REACH registration number: 01-
2119560597-27-XXXX

Classification
Acute Tox. 4 - H302
Skin Irrit. 2 - H315
Eye Irrit. 2 - H319

2/12
Revision date: 25/08/2021 Revision: 0

LOKFIX E77 Part B

m-PHENYLENEBIS( METHYLAMINE) 5-10%

CAS number: 1477-55-0 EC number: 216-032-5 REACH registration number: 01-
2119480150-50-XXXX

Classification
Acute Tox. 4 - H302
Acute Tox. 4 - H332
Skin Corr. 1B - H314
Skin Sens. 1 - H317
Aquatic Chronic 3 - H412

p-TOLUENESULPHONIC ACID 1-5%

CAS number: 104-15-4 EC number: 203-180-0 REACH registration number: 01-
2119538811-39-XXXX

Classification
Skin Irrit. 2 - H315
Eye Irrit. 2 - H319
STOT SE 3 - H335

The Full Text for all R-Phrases and Hazard Statements are Displayed in Section 16.

SECTION 4: First aid measures

4.1. Description of first aid measures

General information Promptly remove any clothing that becomes contaminated. Get medical advice/attention if you
feel unwell.

Inhalation Move affected person to fresh air at once. If in doubt, get medical attention promptly.

Ingestion Do not induce vomiting. Rinse mouth thoroughly with water. Get medical attention.

Skin contact After contact with skin, take off immediately all contaminated clothing, and wash immediately
with plenty of water. Get medical attention. Wash contaminated clothing before reuse.

Eye contact Rinse with water. Remove contact lenses, if present and easy to do. Continue rinsing.
Continue to rinse for at least 15 minutes. Get medical attention.

4.2. Most important symptoms and effects, both acute and delayed
Ingestion Harmful if swallowed.

Skin contact Causes severe burns. May cause skin sensitisation or allergic reactions in sensitive
individuals.

Eye contact Causes serious eye damage.

4.3. Indication of any immediate medical attention and special treatment needed
Notes for the doctor Treat symptomatically.

SECTION 5: Firefighting measures

5.1. Extinguishing media

Suitable extinguishing media Extinguish with foam, carbon dioxide, dry powder or water fog.

Unsuitable extinguishing Do not use water jet as an extinguisher, as this will spread the fire.
media

3/12
Revision date: 25/08/2021 Revision: 0

LOKFIX E77 Part B

5.2. Special hazards arising from the substance or mixture

Hazardous combustion Toxic pyrolysis products Carbon monoxide (CO).
products

5.3. Advice for firefighters

Protective actions during In case of fire and/or explosion do not breathe fumes. Use water spray to reduce vapours.
firefighting Avoid the spillage or runoff entering drains, sewers or watercourses.

Special protective equipment Wear positive-pressure self-contained breathing apparatus (SCBA) and appropriate protective
for firefighters clothing.

SECTION 6: Accidental release measures

6.1. Personal precautions, protective equipment and emergency procedures

Personal precautions Wear protective gloves, eye and face protection. Avoid contact with skin, eyes and clothing.
Provide adequate ventilation.

6.2. Environmental precautions

Environmental precautions Avoid release to the environment. Avoid the spillage or runoff entering drains, sewers or
watercourses.

6.3. Methods and material for containment and cleaning up

Methods for cleaning up Collect spillage. Absorb in vermiculite, dry sand or earth and place into containers. For waste
disposal, see Section 13.

6.4. Reference to other sections

Reference to other sections For personal protection, see Section 8. For waste disposal, see Section 13.

SECTION 7: Handling and storage

7.1. Precautions for safe handling

Usage precautions For professional users only. Use only outdoors or in a well-ventilated area. Wear protective
clothing as described in Section 8 of this safety data sheet. Avoid contact with skin, eyes and
clothing. Do not eat, drink or smoke when using this product.

7.2. Conditions for safe storage, including any incompatibilities

Storage precautions Keep only in the original container in a cool, well-ventilated place. Container must be kept
tightly closed when not in use. Avoid contact with oxidising agents. Keep away from food,
drink and animal feeding stuffs. Store at temperatures between 5°C and 35°C.

7.3. Specific end use(s)

Specific end use(s) The identified uses for this product are detailed in Section 1.2.

SECTION 8: Exposure controls/Personal protection

8.1. Control parameters

Additional advice on limit This mixture contains quartz filler which is firmly bound in the pasty component, and thus not
values freely available during use, so that a risk of dust inhalation is excluded. Exposure limit values
for respirable dusts are not relevant for this product.

2,2,4(or 2,4,4)-TRIMETHYLHEXANE-1,6-DIAMINE (CAS: 25620-58-0)

4/12
Revision date: 25/08/2021 Revision: 0

LOKFIX E77 Part B

PNEC Fresh water; 0.102 mg/l

marine water; 0.01 mg/l
Sediment (Freshwater); 0.662 mg/kg
Sediment (Marinewater); 0.062 mg/kg
STP; 72 mg/l

2,4,6-TRIS(DIMETHYLAMINOMETHYL)PHENOL (CAS: 90-72-2)

PNEC Fresh water; 0.084 mg/l

marine water; 0.0084 mg/l
STP; 0.2 mg/l

m-PHENYLENEBIS( METHYLAMINE) (CAS: 1477-55-0)

DNEL Workers - Inhalation; Long term systemic effects: 1.2 mg/m³

Workers - Inhalation; Long term local effects: 0.2 mg/m³
Workers - Dermal; Long term systemic effects: 0.33 mg/kg/day

PNEC Fresh water; 0.094 mg/l

marine water; 0.009 mg/l
Sediment (Freshwater); 0.43 mg/kg
Sediment (Marinewater); 0.043 mg/kg
STP; 10 mg/l
Soil; 0.045 mg/kg

p-TOLUENESULPHONIC ACID (CAS: 104-15-4)

DNEL Workers - Dermal; Long term systemic effects: 7.6 mg/kg/day

Workers - Inhalation; Long term systemic effects: 53.6 mg/m³

PNEC Fresh water; 0.073 mg/l

marine water; 0.0073 mg/l
Sediment (Freshwater); 0.0577 mg/kg
Sediment (Marinewater); 0.00577 mg/kg
Soil; 0.016 mg/kg

8.2. Exposure controls

Protective equipment

Appropriate engineering Provide adequate ventilation. Mechanical ventilation or local exhaust ventilation may be
controls required.

Eye/face protection Wear tight-fitting, chemical splash goggles or face shield.

Hand protection To protect hands from chemicals, gloves should comply with European Standard EN374. It is
recommended that gloves are made of the following material: Nitrile rubber. Thickness: > 0.7
mm The selected gloves should have a breakthrough time of at least 8 hours.

Other skin and body Wear protective clothing.

protection

Hygiene measures Take off contaminated clothing and wash it before reuse. Wash contaminated skin thoroughly
after handling. Wash after use and before eating, smoking and using the toilet. Do not eat,
drink or smoke when using this product.

5/12
Revision date: 25/08/2021 Revision: 0

LOKFIX E77 Part B

Respiratory protection If ventilation is inadequate, suitable respiratory protection must be worn. Wear a respirator
fitted with the following cartridge: Combination filter, type A2/P2.

SECTION 9: Physical and chemical properties

9.1. Information on basic physical and chemical properties

Appearance Solid. Paste.

Colour Grey. Red.

Odour Characteristic.

pH Not determined.

Melting point Not determined.

Initial boiling point and range Not determined.

Flash point Not applicable.

Evaporation rate Not determined.

Flammability (solid, gas) Not determined.

Upper/lower flammability or Not determined.

explosive limits

Vapour pressure Not determined.

Relative density 1.42 @ 20°C

Solubility(ies) Insoluble in water.

Partition coefficient Not determined.

Auto-ignition temperature Not determined.

Decomposition Temperature Not determined.

Explosive properties Not considered to be explosive.

Oxidising properties Does not meet the criteria for classification as oxidising.

9.2. Other information

Other information No data available.

Volatile organic compound This product contains a maximum VOC content of 21.7 %.

SECTION 10: Stability and reactivity

10.1. Reactivity
Reactivity See Section 10.3 (Possibility of hazardous reactions) for further information.

10.2. Chemical stability

Stability Stable at normal ambient temperatures.

10.3. Possibility of hazardous reactions

Possibility of hazardous The following materials may react violently with the product: Oxidising agents.
reactions

10.4. Conditions to avoid

Conditions to avoid Avoid heat.

10.5. Incompatible materials

6/12
Revision date: 25/08/2021 Revision: 0

LOKFIX E77 Part B

Materials to avoid Strong oxidising agents. Organic peroxides/hydroperoxides.

10.6. Hazardous decomposition products

Hazardous decomposition No known hazardous decomposition products.
products

SECTION 11: Toxicological information

11.1. Information on toxicological effects

Toxicological effects Based on available data the classification criteria are not met.

Acute toxicity - oral

ATE oral (mg/kg) 914.08

Acute toxicity - inhalation

ATE inhalation (vapours mg/l) 111.11

Skin corrosion/irritation
Skin corrosion/irritation Causes severe burns.

Serious eye damage/irritation

Serious eye damage/irritation Causes serious eye damage.

Respiratory sensitisation
Respiratory sensitisation Based on available data the classification criteria are not met.

Skin sensitisation
Skin sensitisation May cause an allergic skin reaction.

Germ cell mutagenicity

Summary Based on available data the classification criteria are not met.

Carcinogenicity
Carcinogenicity Based on available data the classification criteria are not met.

Reproductive toxicity
Summary Based on available data the classification criteria are not met.

Specific target organ toxicity - single exposure

STOT - single exposure Based on available data the classification criteria are not met.

Specific target organ toxicity - repeated exposure

STOT - repeated exposure Based on available data the classification criteria are not met.

Aspiration hazard
Aspiration hazard Based on available data the classification criteria are not met.

Toxicological information on ingredients.

2,2,4(or 2,4,4)-TRIMETHYLHEXANE-1,6-DIAMINE

Acute toxicity - oral

ATE oral (mg/kg) 500.0

2,4,6-TRIS(DIMETHYLAMINOMETHYL)PHENOL

Acute toxicity - oral

Notes (oral LD₅₀) LD₅₀ 2169 mg/kg, Oral, Rat

7/12
Revision date: 25/08/2021 Revision: 0

LOKFIX E77 Part B

ATE oral (mg/kg) 500.0

Acute toxicity - dermal

Notes (dermal LD₅₀) LD₅₀ 1280 mg/kg, Dermal, Rat

m-PHENYLENEBIS( METHYLAMINE)

Acute toxicity - oral

Notes (oral LD₅₀) LD₅₀ 930 mg/kg, Oral, Rat

ATE oral (mg/kg) 500.0

Acute toxicity - dermal

Notes (dermal LD₅₀) LD₅₀ >3100 mg/kg, Dermal, Rabbit

Acute toxicity - inhalation

Notes (inhalation LC₅₀) LC50 1.34 mg/l, Inhalative, (Mist), Rat (OECD 403)

ATE inhalation (vapours 11.0

mg/l)

SECTION 12: Ecological information

Ecotoxicity Harmful to aquatic life with long lasting effects.

12.1. Toxicity
Ecological information on ingredients.

2,2,4(or 2,4,4)-TRIMETHYLHEXANE-1,6-DIAMINE

Acute aquatic toxicity

Acute toxicity - fish NOEC, 30 days: 10.9 mg/l, Brachydanio rerio (Zebra Fish)

Acute toxicity - aquatic NOEC, 21 days: 1.02 mg/l, Daphnia magna

invertebrates

Acute toxicity - aquatic ErC50, 72 hours: 43.5 mg/l, Selenastrum capricornutum

plants

2,4,6-TRIS(DIMETHYLAMINOMETHYL)PHENOL

Acute aquatic toxicity

Acute toxicity - fish LC₅₀, 96 hours: 175 mg/l, Cyprinus carpio (Common carp)

Acute toxicity - aquatic ErC50, 72 hours: 84 mg/l, Desmodesmus subspicatus

plants

m-PHENYLENEBIS( METHYLAMINE)

Acute aquatic toxicity

Acute toxicity - fish LC₅₀, 96 hours: 87.6 mg/l, Oryzias latipes (Red killifish)

Acute toxicity - aquatic EC₅₀, 48 hours: 15.2 mg/l, Daphnia magna

invertebrates NOEC, 21 days: 4.7 mg/l, Daphnia magna

Acute toxicity - aquatic ErC50, 72 hours: 32.1 mg/l, Selenastrum capricornutum

plants

12.2. Persistence and degradability

8/12
Revision date: 25/08/2021 Revision: 0

LOKFIX E77 Part B

Persistence and degradability No data available.

12.3. Bioaccumulative potential

Bioaccumulative potential Not determined.

Partition coefficient Not determined.

Ecological information on ingredients.

2,2,4(or 2,4,4)-TRIMETHYLHEXANE-1,6-DIAMINE

Partition coefficient log Pow: -0.3

2,4,6-TRIS(DIMETHYLAMINOMETHYL)PHENOL

Partition coefficient log Pow: 0.219

m-PHENYLENEBIS( METHYLAMINE)

Bioaccumulative potential BCF: 2.69,

Partition coefficient log Pow: 0.18

p-TOLUENESULPHONIC ACID

Partition coefficient log Pow: 0.93

12.4. Mobility in soil

Mobility Insoluble in water.

12.5. Results of PBT and vPvB assessment

Results of PBT and vPvB This product does not contain any substances classified as PBT or vPvB.
assessment

12.6. Other adverse effects

Other adverse effects None known.

SECTION 13: Disposal considerations

13.1. Waste treatment methods

General information Dispose of waste product or used containers in accordance with local regulations

Waste class 080409

150110

SECTION 14: Transport information

14.1. UN number
UN No. (ADR/RID) 3259

UN No. (IMDG) 3259

UN No. (ICAO) 3259

UN No. (ADN) 3259

14.2. UN proper shipping name

Proper shipping name AMINES, SOLID, CORROSIVE, N.O.S. (2,2,4(or 2,4,4)-trimethylhexane-1,6-diamine, m-
(ADR/RID) Phenylenebis( methylamine))

9/12
Revision date: 25/08/2021 Revision: 0

LOKFIX E77 Part B

Proper shipping name (IMDG) AMINES, SOLID, CORROSIVE, N.O.S. (2,2,4(or 2,4,4)-trimethylhexane-1,6-diamine, m-
Phenylenebis( methylamine))

Proper shipping name (ICAO) AMINES, SOLID, CORROSIVE, N.O.S. (2,2,4(or 2,4,4)-trimethylhexane-1,6-diamine, m-
Phenylenebis( methylamine))

Proper shipping name (ADN) AMINES, SOLID, CORROSIVE, N.O.S. (2,2,4(or 2,4,4)-trimethylhexane-1,6-diamine, m-
Phenylenebis( methylamine))

14.3. Transport hazard class(es)

ADR/RID class 8

ADR/RID classification code C8

ADR/RID label 8

IMDG class 8

ICAO class/division 8

ADN class 8

Transport labels

14.4. Packing group

ADR/RID packing group II

IMDG packing group II

ICAO packing group II

ADN packing group II

14.5. Environmental hazards

Environmentally hazardous substance/marine pollutant

No.

14.6. Special precautions for user

IMDG Code segregation 18. Alkalis
group

EmS F-A, S-B

ADR transport category 2

Emergency Action Code 2X

Hazard Identification Number 80

(ADR/RID)

Tunnel restriction code (E)

14.7. Transport in bulk according to Annex II of MARPOL and the IBC Code
Transport in bulk according to Not applicable.
Annex II of MARPOL 73/78
and the IBC Code

SECTION 15: Regulatory information

10/12
Revision date: 25/08/2021 Revision: 0

LOKFIX E77 Part B

15.1. Safety, health and environmental regulations/legislation specific for the substance or mixture
National regulations The Manufacture, storage and import of hazardous chemicals rules 1989.

EU legislation Regulation (EC) No 1907/2006 of the European Parliament and of the Council of 18
December 2006 concerning the Registration, Evaluation, Authorisation and Restriction of
Chemicals (REACH) (as amended).
Regulation (EC) No 1272/2008 of the European Parliament and of the Council of 16
December 2008 on classification, labelling and packaging of substances and mixtures (as
amended).
Commission Regulation (EU) No 453/2010 of 20 May 2010.

15.2. Chemical safety assessment

No chemical safety assessment has been carried out.

SECTION 16: Other information

Abbreviations and acronyms ADR: European Agreement concerning the International Carriage of Dangerous Goods by
used in the safety data sheet Road.
ADN: European Agreement concerning the International Carriage of Dangerous Goods by
Inland Waterways.
ATE: Acute Toxicity Estimate.
BCF: Bioconcentration Factor.
CAS: Chemical Abstracts Service.
DNEL: Derived No Effect Level.
EC₅₀: 50% of maximal Effective Concentration.
ErC50: the concentration of test substance which results in a 50% reduction in growth rate
relative to the control.
ICAO: Technical Instructions for the Safe Transport of Dangerous Goods by Air.
IMDG: International Maritime Dangerous Goods.
LC₅₀: Lethal Concentration to 50 % of a test population.
LD₅₀: Lethal Dose to 50% of a test population (Median Lethal Dose).
NOEC: No Observed Effect Concentration.
PBT: Persistent, Bioaccumulative and Toxic substance.
PNEC: Predicted No Effect Concentration.
REACH: Registration, Evaluation, Authorisation and Restriction of Chemicals Regulation
(EC) No 1907/2006.
RID: European Agreement concerning the International Carriage of Dangerous Goods by
Rail.
STP: Sewage treatment plant
vPvB: Very Persistent and Very Bioaccumulative.

Revision comments This is the first issue.

Revision date 25/08/2021

Revision 0

SDS number 29985

11/12
Revision date: 25/08/2021 Revision: 0

LOKFIX E77 Part B

Hazard statements in full H302 Harmful if swallowed.

H314 Causes severe skin burns and eye damage.
H315 Causes skin irritation.
H317 May cause an allergic skin reaction.
H318 Causes serious eye damage.
H319 Causes serious eye irritation.
H332 Harmful if inhaled.
H335 May cause respiratory irritation.
H412 Harmful to aquatic life with long lasting effects.

This information relates only to the specific material designated and may not be valid for such material used in combination
with any other materials or in any process. Such information is, to the best of the company's knowledge and belief, accurate
and reliable as of the date indicated. However, no warranty, guarantee or representation is made to its accuracy, reliability or
completeness. It is the user's responsibility to satisfy himself as to the suitability of such information for his own particular use.

12/12
 Design Yield
Rebar Hole
Load Rebar
Diameter Diameter Design Tension Load Nbd (kN) - C20/25 Concrete
FE500
(mm) (mm)
NRd,s (kN)

Ø8 10 21.87 16.08 18.77 21.45 21.87

Ø10 12 34.16 20.11 23.46 26.81 30.16 33.51 34.16
Ø12 16 49.20 28.15 32.17 36.19 40.21 44.23 48.25 49.20
Ø16 20 87.46 42.89 48.25 53.62 58.98 64.34 69.70 85.79 87.46
Ø20 25 136.66 60.32 67.02 73.72 80.42 87.13 107.23 113.94 134.04 136.66
Ø25 30/32 213.53 78.54 86.39 94.25 102.10 125.66 133.52 157.08 164.93 196.35 204.20 213.53
Ø28 35 267.85 105.56 114.35 140.74 149.54 175.93 184.73 219.91 228.71 246.30
Ø32 40 349.85 130.69 160.85 170.90 201.06 211.12 251.33 261.38 281.49
Embedment Depth (mm) 60 70 80 90 100 110 120 130 160 170 200 210 250 260 280

Rebar Hole Rebar

Diameter Diameter FE500/550 Design Tension Load Nbd (kN) - C20/25 Concrete
(mm) (mm) NRk,s (kN)

Ø28 35 267.85 255.10 263.89 267.85

Ø32 40 349.85 291.54 301.59 311.65 321.70 331.75 341.81 349.85 349.85
Embedment Depth (mm) 290 300 310 320 330 340 350 360
Note:
1. The above shown values are obtained for single rebar in uncracked concrete.
2. The above values are considering ideal condition where concrete cone failure doesn't happen first.
3. For post installed rebar connection, the minimum embedment depth shall be 10x diameter of rebar.
4. Incase of higher grade of concrete, the values has to be multipied with increasing factor mentioned in ETA