Tool box–Borescope (option)

Through wireless borescope, you can check the interior spaces of

mechanical equipment, which are difficult to observe directly with naked
eyes.

-1-
Precautions Before Use
The user is responsible for all damages that are caused by not
understanding the contents of this Wireless Borescope User Manual
thoroughly or by controlling it differently from the contents of the
User Manual.

• In the case of connecting to DC charger, do not use chargers other than the designated DC charger.

• Please make sure that all the cables are normally connected during the operation, and do
not disconnect the communication cable or power cable before the operation completed.
• Please be cautious that you may not be able to receive a normal service, in the case where the
product is arbitrarily disassembled, modified or remodeled.
• Make sure to use genuine products manufactured at GIT Co., Ltd. for cables,
chargers, other parts and accessories that are used together, and also use the
designated devices and programs.
• Please handle the product within the operating temperature and humidity range.

• A wireless communication failure might occur if this product is used in an excessively

obstructed space. Wireless communication can be stopped temporarily or continuously
depending on the wireless communication environment.

• The use of this product may be restricted in long-range communication setting as it is a

short-range wireless device.

Personal injuries or material damages can occur if the user does not
pay attention for handling, and more serious results may occur under
certain conditions. Please comply with all safety rules and instructions.

• Please do not store the product in places where flammable materials or strong static electricity
can be generated. Chemical or acid substances may cause corrosion of the product and
accessories. Please do not apply shock to the product.
• Please cool down the engine sufficiently (50℃ or lower), and use the product at low
temperature conditions.
• Please do not touch the camera part with your hands while LED lighting is turned on as it may
be hot. There is a risk of burns. When you use the product in the vehicle’s engine room, pay
attention to damages caused by high-temperature and moving parts.
• Please make sure that the main body that contains the charging battery and cables does not
make contact with water. Please do not disassemble the charging battery.
• Pay attention to prevent water leak caused by inappropriate use of the charging battery from
making contact with your eyes or skin. Make sure to use only the designated product for the
charging battery.
• Pay attention to prevent connections of the camera and charging cables from making contact
with water. Be cautious for storing all components when not in use.
• Please do not pull the cables when moving or using the product.

-2-
• GIT Co., Ltd. is not responsible for damages caused by using a PC that is not recommended by
the company.
• Please do not expose the product to X-ray or microwave. Serious damages might occur to the
product. Please do not store the product in the following places:
- Places where temperature or humidity is too high (please check the specification of the
product).
- Places that are exposed to direct light for a long time
- Inside the vehicle during summer
- Places having a lot of moisture

-3-
Basic Configuration Items
Item Image Description
The Main Body performs the borescope
Main Body function by connecting with the camera and
Flexible Tube.
This is a 0˚ camera used for taking the front
0˚ Camera
view.

This is a 90˚ camera used for taking the side

90˚ Camera
views.

This is a probe used to connect the Main Body

Flexible Tube
with the camera.

You can lift small bolts or screws by mounting

0˚ Magnetic Holder
it on the camera lens home.

You can lift small bolts or screws by mounting

90˚ Magnetic Holder
it on the camera lens home.
This is a cable used to perform wire
communication between the borescope and
Micro USB Cable
tablet.
Cable length: 150 cm

This is a jack used to supply power to VCI,

DC Cable
using DC power adaptor.

This is used for charging by connecting DC

Charger and Plug cable.
Plug: 1 type out of 3 types is provided.
This is Wireless Borescope User Manual,
which contains methods of using the product
safety and normally, as well as the product
Manual
specification, etc.
(the specification may vary depending on
situation.)
This is a c-type gender that can replace 5-pin
USB C-type Gender
cable.

This is a cleaning fabric for wiping the camera

Cleaning Fabric
lens.

This is a container for carrying and storing the

Container
Wireless Borescope product.

-4-
Name of Each Part

Wi-Fi mode power button

UP: LED brightness button (0 to 3 level)

DOWN: free-view rotation button (90°)

Capture button
Press for a long time: start/stop video recording
Press for a short time: photo taking

Status indicating LED

+DC 5V input terminal

USB input terminal

Status Indicating LED

Connection Status LED Remarks

Type
Booting Flashing blue light
Booting completed/hold status for Wi-Fi Flashing blue and
connection green lights
Connecting to Wi-Fi Flashing green light
Wi-Fi
Connecting to Wi-Fi completed Green light turned on
Flashing red and blue
Low battery
lights
When terminating the device Flashing red light
Charging Red light turned on
Charge
Fully charged Red light turned off
USB Program connection completed Blue light turned on

-5-
Product Assembly
1. Plug the flexible tube to the Main Body, and fix it by rotating the screws.

Check the arrows and the

direction of the holes.

2. Mount the camera on the opposite side of the Flexible Tube, and fix it by rotating the
screws.

Camera

-6-
Charging of the Product
This product requires charging as it consumes its own battery when used in wireless
condition.
* USB connection type can be used without charging.

1. Connect DC cable to 5V 2A charger.

DC Cable

2. Peel of the waterproof cover on the rear side of the Main Body, and connect DC cable
to DC input terminal.

* Power supply method

Wi-Fi mode: battery and charger
USB mode: tablet

-7-
Diagnosis Device ↔ Product Connection

USB Connection Method

1. If Wi-Fi power is turned on, press the Power button to turn it off.
To enter USB mode, Wi-Fi power should be turned on.

Wi-Fi mode power LED

Wi-Fi mode power button

2. Use Micro USB Cable to connect the Diagnosis Device to Wireless Borescope Module.

-8-
3. Touch the Borescope.

4. Attempt to connect USB automatically. Once USB connection is completed, the screen
moves to the photo taking screen.

KA981121312449231

If USB connection is failed, try connecting USB cable again.

-9-
Wi-Fi Connection Method
1. Press button for 3 seconds to allow the Wireless Borescope Module to enter Wi-
Fi hold status.
Flashing red and green LED lights appear.

Wi-Fi mode power button

2. Run the Wireless Borescope, and enter 4-digit code indicated on the device label.

CODE : XXXX

3. Once the device is searched, press Connect button to complete the connection.

- 10 -
Screen Description

Recording Screen
Battery life LED brightness
Connection status Mic volume Setting

Text writing
mode

Photo editing

Photo taking

Video
recording

Switch to free-
view screen

Function Description
You can adjust the screen to a desired brightness by pressing LDF Brightness
LED brightness
Adjustment button.
You can configure the resolution of the photo to be taken, as well as required
Setting
time for entering the power-saving mode.

Text writing mode You can write a memo on the captured screen.

Photo editing You can edit the captured photo using a pen or textbox.

Switch to free-view
You can rotate the free-view screen by 90° each time.
screen

- 11 -
Battery Replacement
1. Use a driver to rotate the screw on the rear side in counterclockwise direction.

2. Take out the screw, and disassemble the batter cover on the handle side downwards.

3. Take out the battery and replace it with a new battery.

- 12 -
Product Specification

Item Details

Camera 2 EA [front view (0°), side views (90°)]

Resolution C-MOS [640X480, 800X600, 1,280X960]

Lens Angle of view: 67°/ Aperture: F2.8 None AF/Antifogging coating

Focus range 9.5 to 300 mm

LED White Chip LED 6 EA

Outer diameter Camera Head Ø8.2 Camera Joint Wire Ø8.0

Product length 1m

Magnetic holder 2 EA [front view (0°), side views (90°)]

3 Regions
segmentation Camera/Flexible Tube/Main Body
assembly
Brightness
Adjusted from the hardware (3-phase)
adjustment
Camera connection
Wi-Fi Direct (Wireless LAN IEEE 802.11 b/g/n) USB (UVC 1.1)
type

Battery capacity 2,600 mAh

Use temperature -20 ℃ ~ +70 ℃

Dust-
proofing/moisture- IP64
proofing

Certifications
The wireless device has a possibility of having a radio interference during its
operation.
This device complies with part 15 of FCC Rules. Operation is subject to
the following two condition: (1) This Device may not cause harmful, and
(2) This device must accept any interface received, including interface
that may cause undesired operation.

- 13 -