Scribd
Upload
199 views21 pages

PYQ

The document outlines the examination structure for the Design of Concrete Structures course at the National Institute of Technology Durgapur, including details about a double storey lecture hall complex and various design tasks related to structural components. Students are required to answer specific questions, including calculations for loads, design of slabs and footings, and reinforcement detailing. The examination emphasizes the application of IS codes and design methodologies such as Limit State Method (LSM) and Working Stress Method (WSM).

Uploaded by

souradas47
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
199 views21 pages

PYQ

The document outlines the examination structure for the Design of Concrete Structures course at the National Institute of Technology Durgapur, including details about a double storey lecture hall complex and various design tasks related to structural components. Students are required to answer specific questions, including calculations for loads, design of slabs and footings, and reinforcement detailing. The examination emphasizes the application of IS codes and design methodologies such as Limit State Method (LSM) and Working Stress Method (WSM).

Uploaded by

souradas47
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
Ea Body of the Question NrroGr/BTECHOCe) Answer to the point and brief Use of IS Code is permitted. Use Combination M25 & Fes15, if not mentioned specifically Assume any suitable data, if not supplied Answer Ques No.1 and any two from the rest. reg Even 2023-24 NATIONAL INSTITUTE OF TECHNOLOGY DURGAPUR Even Semester End-term Examination, 2am@@*23 -24 Full Marks: 60 Course Code: CEC 402 Course Name: Design of Concrete Structures Time: 180 Minutes Question Paper No.: [Link]/CEC 402/2024.04/01 ate of Exam: 23/04/2024 co | A double storey lecture hall complex has clear hall dimension 15m x 6m at both floor /storey levels. Floor to floor height is 3.6m. The complex along, with the floor slab is supported on RCC frame structure with 4 nos. of | 250x250 columns (equally spaced) along the longer sides /edges each. Columns are supported on isolated footing at 1.2m below existing ground level (EGL) At ground floor level (+0.6m) GFL, the floor is supported directly on ground. At 1* floor level, the floor slab is supported on five intermediate RC beams along shorter direction, having clear span = 5.0m placed @2.5 m c/c. At 2” floor /Roof level, the floor slab is supported on ‘two intermediate RC beams along shorter direction, and one intermediate RC beams along longer direction placed centrally. Assume live load of 3.0 kNim a) | Draw aneat sketch (single line) of the hall with plan at both 1* and 2 floor ‘roof level showing column, beam positions including dimensions 22. co2 b) | Caleulate the floor load, load of brick work, self-wt of beams at 2" f1, (Roof level of the Hall, 1* floor level and GFL. col ©) | Design the roof slab (two-way) following LSM. Draw / Show details of reinforcements with curtailments in plan and section OR Design the slab (one-way) at 1* floor level following WSM. Draw / Show details of reinforcements with curtailments in plan and section 10 CO3 f Ques No. Body of the Question Marks Consider the above hall (Ques.-1) Calculate the load for a corner column or intermediate column at Ground level (GL,). Also calculate moment due to minimum eccentricity. OR Design an isolated footing for a rectangular column 400mm x 250mm. carrying a unfactored load P=500 KN and M=15.0 kN-m. Assume safe bearing capacity of soil as 150 kN/m2 at a depth of 1.2 m below ground level. Design the reinforcement for the same and draw rebar layout in plan and section. és Course Outcomes CO1. Apply knowledge of solid mechanics for design solutions C02: Understand basic design philosophies apy C03: Formulate, analyze, plicable to concrete st ‘and design basic components of Civil Engineering Reinforced Concrete stru ictures Ea Body of the Question NrroGr/BTECHOCe) Answer to the point and brief Use of IS Code is permitted. Use Combination M25 & Fes15, if not mentioned specifically Assume any suitable data, if not supplied Answer Ques No.1 and any two from the rest. reg Even 2023-24 NATIONAL INSTITUTE OF TECHNOLOGY DURGAPUR Even Semester End-term Examination, 2am@@*23 -24 Full Marks: 60 Course Code: CEC 402 Course Name: Design of Concrete Structures Time: 180 Minutes Question Paper No.: [Link]/CEC 402/2024.04/01 ate of Exam: 23/04/2024 co | A double storey lecture hall complex has clear hall dimension 15m x 6m at both floor /storey levels. Floor to floor height is 3.6m. The complex along, with the floor slab is supported on RCC frame structure with 4 nos. of | 250x250 columns (equally spaced) along the longer sides /edges each. Columns are supported on isolated footing at 1.2m below existing ground level (EGL) At ground floor level (+0.6m) GFL, the floor is supported directly on ground. At 1* floor level, the floor slab is supported on five intermediate RC beams along shorter direction, having clear span = 5.0m placed @2.5 m c/c. At 2” floor /Roof level, the floor slab is supported on ‘two intermediate RC beams along shorter direction, and one intermediate RC beams along longer direction placed centrally. Assume live load of 3.0 kNim a) | Draw aneat sketch (single line) of the hall with plan at both 1* and 2 floor ‘roof level showing column, beam positions including dimensions 22. co2 b) | Caleulate the floor load, load of brick work, self-wt of beams at 2" f1, (Roof level of the Hall, 1* floor level and GFL. col ©) | Design the roof slab (two-way) following LSM. Draw / Show details of reinforcements with curtailments in plan and section OR Design the slab (one-way) at 1* floor level following WSM. Draw / Show details of reinforcements with curtailments in plan and section 10 CO3 f Ques No. Body of the Question Marks Consider the above hall (Ques.-1) Calculate the load for a corner column or intermediate column at Ground level (GL,). Also calculate moment due to minimum eccentricity. OR Design an isolated footing for a rectangular column 400mm x 250mm. carrying a unfactored load P=500 KN and M=15.0 kN-m. Assume safe bearing capacity of soil as 150 kN/m2 at a depth of 1.2 m below ground level. Design the reinforcement for the same and draw rebar layout in plan and section. és Course Outcomes CO1. Apply knowledge of solid mechanics for design solutions C02: Understand basic design philosophies apy C03: Formulate, analyze, plicable to concrete st ‘and design basic components of Civil Engineering Reinforced Concrete stru ictures Body of the Question ‘A short R.C column of 250mm x 400mm section, reinforced with 4 bars of 16mm di the longer sides. Determine the maximum allowable ulti if the unsupported lengths about x-axis and y-axis are 3.0m and 3.2m respectively. Use M20 grade concrete and Fe415 steel. Assume cover to the centre of steel as 50mm. the four corners and 2 bars of 12mm dia at the middle of te axial load, ‘An RC, Column 500X300mm is subjected to an axial ultimate load of } 2500 KN and bent in single curvature about the major axis with M=90 KNm ‘as ultimate moments. Taking the unsupported length as 7.0m, design the column section (both main rebar & ties) 12 C03 OR Design a typical flight of dog-legged staircase for the following data. Riser R=150mm, Tread T=250mm, floor to floor height equal to 3.6 m, width of each flight 1.25m and live load = 400 kg/m?. Show the reinforcement details the flight. 20 CO3 Body of the Question Marks ‘A T-beam with flange width of 600mm, flange thickness of 100mm, width of rib 250mm, effective depth 400mm and with a tension steel area 2000mm? has to be constructed. Calculate ultimate moment capacity of the section according to IS456-2000 20 OR b) Design a cantilever retaining wall to retain earth embankment 4.5 m_ above ground level. The unit weight of cohesionless fill is 18kN/m?> and the earth pressure co-efficient is 0.35 .The embankment is horizontal at its top. The safe bearing capacity of soil may be taken as 150KN/m?, coefficient of friction between concrete and soil is 0.5 20 C03 ee ne saa on/2023°24 e yew eee INSTITUTE OF TECHNOLOGY DURGAPUR- ‘ven Semester Mid-term Examination, 2023-24 Course Code: CEC 402 G ( : ull Marks: 25 ues. Pap. sot Bam 2 ‘aper No.: [Link]/AKS,CEC402/2024.02/01 Date of Exam: 20-02-2024 Answer to the point and brief, 2 marks allotted for neatmess. Use of IS:456-2000 is permitted. Use combination of M20 and Fe415 Show details/sections compulsorily Assume any suitable data, if not supplied Ques Body of the Question ~ ‘| Marks | Mapped | No. £8 1 a) | State the assumptions of working stress method(WSM) biome ce! draw a)Original c/s, b)Transformed c/s, and c)Stress profile for a singly reinforced rectangular section OR and State the assumptions of limit state method (LSM)of design | 3+3 and draw a)Original c/s, b)Stress profile and c)strain profile for a singly reinforced rectangular section b) | Derive the expression for “moment factor” for balanced singly | 2+2 co2 reinforced concrete section following WSM and LSM. | ©) | State the advantage of Flanged Beam over rectangular beam | 1+1 col and its applicability. Total=12 Ques _| Body of the Question Marks | Mapped | No. co mnerete beam of length 3m carries a} 2+2 C03 2 a) | A cantilever reinforced co uniformly distributed load of 10.0 KN/m over the entire span and a point load of 20.0 KN at its free end and mid-point each. Draw BMD & SFD b) | Design the beam section against i)Flexure and ii) Shear from | 4*3 cO3 the first principle considering doubly-reinforced section from the first principle. Use applicable codal provisions and draw 2 the length of the beam considering length. Assume the width of the t WSM or LSM. RC details alon; appropriate bond /anchorage beam 250mm and follow either let. ee 4 a a ee Total=11 [Link]. / 4 Sem, / End Term (Reg,) Exam./ 2023-24 NATIONAL INSTITUTE OF TECHNOLOGY DURGAPUR Even Semester End-term Regular Examination, 2023-24 Course Code: CEC401 Full Marks: 60 Course Name: STRUCTURAL ANALYSIS~ 1 Time: 3 Hours {Question Paper No.: NITOGP-CE-401/2023-24/7-REG/1 Date of Exam: 23/08/2024 ‘Answer all questions in Part-A (Qt to Q3) & Par-6 (Q4 to a8), Attempt Q5 or Q. Figures in the margin indicate full marks Part A [ Question | & 7 No | 1 Find the correct answer ofthe folowing (Fora. prismatic cantilever beam of length °L', carrying a triangular load of Pano, st the support and zero athe free end, the slope tthe fre end is given by (2) wLY8EL —(b) wLVI2E1——_(e) wLYoae (4) L486 | (0 Fora cantilever beam of length ‘L’ & flexural rigidity El carries a moment °M’ | concentrated atthe fre end. the deflection at the free end is given by | Pereee et (HMIVIZEN Xe) MLGEL dy MLE (Gi simply supported beam of span L'& flexural rigidity El, caries a unit point load at the centre. The strain energy inthe beam due to bending i given by (@) 10cm (b) 2.0m ()[Link] () 25 em () Fora cantilever beam of length *L’ & flexural rigidity El carries a point load |

You might also like