Spring lock washer with square ends

DIN 127 B
NEN 1197 B
NF E25-515
BS 4464 B

Technical data
For nom.size d1 (min.) d2 (max.) s
M2 2,1 4,4 0,5
M2,3 (≠DIN) 2,4 4,9 0,6
M2,5 2,6 5,1 0,6
M2,6 (≠DIN) 2,7 5,2 0,6
M3 3,1 6,2 0,8
M3,5 3,6 6,7 0,8
M4 4,1 7,6 0,9
M5 5,1 9,2 1,2
M6 6,1 11,8 1,6
1/4 (≠DIN) 6,4 12,1 1,6
M7 7,1 12,8 1,6
M8 8,1 14,8 2
3/8 (≠DIN) 9,7 17,6 2,2
M10 10,2 18,1 2,2
M11 (≠DIN) 11,2 18,2 2,2
M12 12,2 21,1 2,5
1/2 (≠DIN) 13 21,8 2,5
M14 14,2 24,1 3
M16 16,2 27,4 3,5
M18 18,2 29,4 3,5
M20 20,2 33,6 4
M22 22,5 35,9 4
M24 24,5 40 5
1.IN. (≠DIN) 26,5 42,5 5
M27 27,5 43 5
M30 30,5 48,2 6
M33 (≠DIN) 33,5 55,2 6
M36 36,5 58,2 6
7 M39
M42
39,5
42,5
61,2
68,2
6
7
M45 45,5 71,2 7
M48 49 75 7
M52 53 83 8
M56 57 87 8
M60 61 91 8
M64 65 95 8
M68 69 99 8
M72 73 103 8
M76 (≠DIN) 77 107 8
• Spring washers acc. to DIN 127 B should be used in combination with fasteners of property class ≤ 5.8, use under dynamic load is not allowed.
• For locking under dynamic load is referred to locking edge washers, SCHNORR safety washers and NORD-LOCK vibration proof washers.
• Depending on availability these articles can be supplied zinc plated as well as mechanical plated.
• WARNING: electro-galvanizing of these products may cause hydrogen embrittlement

Article groups
Material Surface treatment Packaging Code Page
Spring steel DIN267-26 Standard 37000 7-39
Spring steel DIN267-26 FLZNNC-NC6 Standard 37024 7-39
Spring steel DIN267-26 Zipl Standard 37020 7-39
Spring steel DIN267-26 Zipl Large 37030 7-39
Spring steel DIN267-26 Zipl yell.p. Standard 37060 7-40
Spring steel DIN267-26 Hot d.g. Standard 37025 7-40
St.St. A2 Standard 51450 7-40
St.St. A4 Standard 55450 7-40

7-38 121 - www.fabory.com

 37000 Spring lock washer with square ends L05A
Material Spring steel DIN267-26
Packaging Standard

Spring lock washer with square ends

37000

For nom. size  Art.number For nom. size  Art.number For nom. size  Art.number
M3 250 37000.030.001 1/2 150 37000.127.001 M39 10 37000.390.001
M3,5 250 37000.035.001 M14 100 37000.140.001 M42 10 37000.420.001
M4 250 37000.040.001 M16 100 37000.160.001 M45 10 37000.450.001
M5 250 37000.050.001 M18 100 37000.180.001 M48 10 37000.480.001
M6 250 37000.060.001 M20 100 37000.200.001 M52 10 37000.520.001
1/4 250 37000.063.001 M22 50 37000.220.001 M56 5 37000.560.001
M7 250 37000.070.001 M24 50 37000.240.001 M60 5 37000.600.001
M8 200 37000.080.001 1.IN. 50 37000.254.001 M64 5 37000.640.001
3/8 200 37000.096.001 M27 25 37000.270.001 M68 5 37000.680.001
M10 200 37000.100.001 M30 25 37000.300.001 M72 5 37000.720.001
M11 150 37000.110.001 M33 25 37000.330.001 M76 5 37000.760.001
M12 150 37000.120.001 M36 25 37000.360.001
Spring lock washer with square ends
37000

37024 Spring lock washer with square ends L05A

Material Spring steel DIN267-26
Surface treatment Zinc flake Cr6+ free - ISO 10683 flZnnc
Packaging Standard

Spring lock washer with square ends

37024

For nom. size  Art.number For nom. size  Art.number For nom. size  Art.number
M6 250 37024.060.001 M12 150 37024.120.001 M24 50 37024.240.001
M8 200 37024.080.001 M16 100 37024.160.001 M30 25 37024.300.001
M10 200 37024.100.001 M20 100 37024.200.001

• Technical brochure available on request.

Spring lock washer with square ends
37024

37020 Spring lock washer with square ends L05A

Material Spring steel DIN267-26
Surface treatment Zinc plated
Packaging Standard

Spring lock washer with square ends

37020

For nom. size  Art.number For nom. size  Art.number For nom. size  Art.number
7
M2 500 37020.020.001 M7 250 37020.070.001 M18 100 37020.180.001
M2,3 500 37020.023.001 M8 200 37020.080.001 M20 100 37020.200.001
M2,6 500 37020.026.001 3/8 200 37020.096.001 M22 50 37020.220.001
M3 250 37020.030.001 M10 200 37020.100.001 M24 50 37020.240.001
M3,5 250 37020.035.001 M11 150 37020.110.001 1.IN. 50 37020.254.001
M4 250 37020.040.001 M12 150 37020.120.001 M27 25 37020.270.001
M5 250 37020.050.001 1/2 150 37020.127.001 M30 25 37020.300.001
M6 250 37020.060.001 M14 100 37020.140.001 M33 25 37020.330.001
1/4 250 37020.063.001 M16 100 37020.160.001 M36 25 37020.360.001
Spring lock washer with square ends
37020

37030 Spring lock washer with square ends L05A

Material Spring steel DIN267-26
Surface treatment Zinc plated
Packaging Large

Spring lock washer with square ends

37030

For nom. size  Art.number For nom. size  Art.number For nom. size  Art.number
M3 2500 37030.030.001 M8 2000 37030.080.001 M16 500 37030.160.001
M4 2500 37030.040.001 M10 1500 37030.100.001 M20 250 37030.200.001
M5 2500 37030.050.001 M12 1000 37030.120.001 M22 250 37030.220.001
M6 2000 37030.060.001 M14 500 37030.140.001 M24 250 37030.240.001
Spring lock washer with square ends

121 - www.fabory.com 7-39

 37060 Spring lock washer with square ends L05A
Material Spring steel DIN267-26
Surface treatment Zinc plated yellow passivated
Packaging Standard

Spring lock washer with square ends

37060

For nom. size  Art.number For nom. size  Art.number For nom. size  Art.number
M3 250 37060.030.001 M8 200 37060.080.001 M18 100 37060.180.001
M4 250 37060.040.001 M10 200 37060.100.001 M20 100 37060.200.001
M5 250 37060.050.001 M12 150 37060.120.001 M22 50 37060.220.001
M6 250 37060.060.001 M14 100 37060.140.001 M24 50 37060.240.001
M7 250 37060.070.001 M16 100 37060.160.001
Spring lock washer with square ends
37060

37025 Spring lock washer with square ends L05A

Material Spring steel DIN267-26
Surface treatment Hot dip galvanized
Packaging Standard

Spring lock washer with square ends

37025

For nom. size  Art.number For nom. size  Art.number For nom. size  Art.number
M6 250 37025.060.001 M14 150 37025.140.001 M22 50 37025.220.001
M8 200 37025.080.001 M16 100 37025.160.001 M24 50 37025.240.001
M10 200 37025.100.001 M18 100 37025.180.001 M27 25 37025.270.001
M12 150 37025.120.001 M20 100 37025.200.001 M30 25 37025.300.001
Spring lock washer with square ends
37025

51450 Spring lock washer with square ends R07A

Material Stainless steel A2
Packaging Standard
DIN ≈127 B
NEN ≈1197 B
NF ≈E25-515
BS ≈4464 B
Spring lock washer with square ends
51450

For nom. size  Art.number For nom. size  Art.number For nom. size  Art.number
M2 200 51450.020.001 M7 500 51450.070.001 M20 200 51450.200.001
M2,3 200 51450.023.001 M8 500 51450.080.001 M22 100 51450.220.001
M2,5 200 51450.025.001 3/8 500 51450.096.001 M24 100 51450.240.001
M2,6 200 51450.026.001 M10 500 51450.100.001 1.IN. 100 51450.254.001
M3 500 51450.030.001 M11 500 51450.110.001 M27 50 51450.270.001
7 M3,5
M4
500
500
51450.035.001
51450.040.001
M12
1/2
500
500
51450.120.001
51450.127.001
M30
M33
50
50
51450.300.001
51450.330.001
M5 500 51450.050.001 M14 200 51450.140.001 M36 50 51450.360.001
M6 500 51450.060.001 M16 200 51450.160.001
1/4 500 51450.063.001 M18 200 51450.180.001

• Technical data is according to DIN with the exception of material type stainless steel.
Spring lock washer with square ends
51450

55450 Spring lock washer with square ends R47A

Material Stainless steel A4
Packaging Standard
DIN ≈127 B
NEN ≈1197 B
NF ≈E25-515
BS ≈4464 B
Spring lock washer with square ends
55450

For nom. size  Art.number For nom. size  Art.number For nom. size  Art.number
M2 200 55450.020.001 3/8 500 55450.096.001 M22 100 55450.220.001
M2,5 200 55450.025.001 M10 500 55450.100.001 M24 100 55450.240.001
M3 500 55450.030.001 M12 500 55450.120.001 1.IN. 100 55450.254.001
M4 500 55450.040.001 1/2 500 55450.127.001 M27 50 55450.270.001
M5 500 55450.050.001 M14 200 55450.140.001 M30 50 55450.300.001
M6 500 55450.060.001 M16 200 55450.160.001 M33 50 55450.330.001
1/4 500 55450.063.001 M18 200 55450.180.001 M36 50 55450.360.001
M8 500 55450.080.001 M20 200 55450.200.001
Spring lock washer with square ends
55450

• Technical data is according to DIN with the exception of material type stainless steel.

7-40 121 - www.fabory.com

 Spring lock washer for screws with cylindrical heads
DIN 7980
BS 4464 A

Technical data
For nom.size d1 (min.) d2 (max.) s
M3 3,1 5,6 1
M4 4,1 7 1,2
M5 5,1 8,8 1,6
M6 6,1 9,9 1,6
1/4 (≠DIN) 6,5 11,2 2
M8 8,1 12,7 2
M10 10,2 16 2,5
M12 12,2 18 2,5
1/2 (≠DIN) 13 20,2 3
M14 14,2 21,1 3
M16 16,2 24,4 3,5
M18 18,2 26,4 3,5
M20 20,2 30,6 4,5
M22 22,5 32,9 4,5
M24 24,5 35,9 5
1.IN. 25,9 38,4 5
M27 27,5 38,9 5
M30 30,5 44,1 6
M36 36,5 52.2 7

Article groups
Material Surface treatment Packaging Code Page
Spring steel DIN267-26 Standard 37200 7-41
Spring steel DIN267-26 Zipl Standard 37220 7-42
St.St. A2 Standard 51390 7-42
St.St. A4 Standard 55390 7-42

37200 Spring lock washer for screws with cylindrical heads L07D
7
Material Spring steel DIN267-26
Packaging Standard

Spring lock washer for screws with cylindrical heads

37200

For nom. size  Art.number For nom. size  Art.number For nom. size  Art.number
M3 250 37200.030.001 M12 150 37200.120.001 M24 50 37200.240.001
M4 250 37200.040.001 1/2 150 37200.127.001 1.IN. 50 37200.254.001
M5 250 37200.050.001 M14 100 37200.140.001 M27 50 37200.270.001
M6 250 37200.060.001 M16 100 37200.160.001 M30 50 37200.300.001
1/4 250 37200.063.001 M18 250 37200.180.001 M36 50 37200.360.001
M8 200 37200.080.001 M20 100 37200.200.001
M10 200 37200.100.001 M22 50 37200.220.001

• Spring lock washers acc. to DIN 7980 should be used in combination with fasteners of property class < 8.8, use under dynamic load is not allowed.
• For locking under dynamic load is referred to locking edge washers, SCHNORR safety washers and NORD-LOCK vibration proof washers.
• Depending on availability these articles can be supplied zinc plated as well as mechanical plated.
• Warning: electro-galvanizing of these products may cause hydrogen embrittlement.
Spring lock washer for screws with cylindrical heads

121 - www.fabory.com 7-41

 37220 Spring lock washer for screws with cylindrical heads L07D
Material Spring steel DIN267-26
Surface treatment Zinc plated
Packaging Standard

Spring lock washer for screws with cylindrical heads

37220

For nom. size  Art.number For nom. size  Art.number For nom. size  Art.number
M3 250 37220.030.001 M10 200 37220.100.001 M22 50 37220.220.001
M4 250 37220.040.001 M12 150 37220.120.001 M24 50 37220.240.001
M5 250 37220.050.001 M14 100 37220.140.001 M27 50 37220.270.001
M6 250 37220.060.001 M16 100 37220.160.001 M30 50 37220.300.001
M8 200 37220.080.001 M20 100 37220.200.001

• Spring lock washers acc. to DIN 7980 should be used in combination with fasteners of property class < 8.8, use under dynamic load is not allowed.
• For locking under dynamic load is referred to locking edge washers, SCHNORR safety washers and NORD-LOCK vibration proof washers.
• Depending on availability these articles can be supplied zinc plated as well as mechanical plated.
Spring lock washer for screws with cylindrical heads
37220

51390 Spring lock washer for screws with cylindrical heads R09A
Material Stainless steel A2
Packaging Standard
DIN ≈7980
BS ≈4464 A

Spring lock washer for screws with cylindrical heads

51390

For nom. size  Art.number For nom. size  Art.number For nom. size  Art.number
M3 250 51390.030.001 M10 200 51390.100.001 M20 100 51390.200.001
M4 250 51390.040.001 M12 200 51390.120.001 M24 50 51390.240.001
M5 250 51390.050.001 M14 100 51390.140.001 M27 50 51390.270.001
M6 250 51390.060.001 M16 100 51390.160.001 M30 50 51390.300.001
M8 250 51390.080.001 M18 100 51390.180.001

• Use under dynamic load is not allowed.

• For locking under dynamic load is referred to NORD-LOCK vibration proof washers and SCHNORR safety washers.
• The austenetic steel type is at the manufacturer’s discretion, and can vary from the steel types stated in DIN 267-11.
Spring lock washer for screws with cylindrical heads
51390

55390 Spring lock washer for screws with cylindrical heads R49A
Material Stainless steel A4
Packaging Standard
DIN ≈7980
BS ≈4464 A

7
Spring lock washer for screws with cylindrical heads
55390

For nom. size  Art.number For nom. size  Art.number For nom. size  Art.number
M3 250 55390.030.001 M10 200 55390.100.001 M20 100 55390.200.001
M4 250 55390.040.001 M12 200 55390.120.001 M24 50 55390.240.001
M5 250 55390.050.001 M14 100 55390.140.001 M27 50 55390.270.001
M6 250 55390.060.001 M16 100 55390.160.001 M30 50 55390.300.001
M8 250 55390.080.001 M18 100 55390.180.001
Spring lock washer for screws with cylindrical heads
55390

• Use under dynamic load is not allowed.

• For locking under dynamic load is referred to NORD-LOCK vibration proof washers and SCHNORR safety washers.
• The austenetic steel type is at the manufacturer’s discretion, and can vary from the steel types stated in DIN 267-11.

7-42 121 - www.fabory.com

 Double coil spring lock washer

Technical data
For nom.size d1 d2 s h
M5 5,1 8,7 1,2 4,2
M6 6,1 11,1 1,6 5,6
M8 8,2 14,2 2 7
M10 10,2 17,2 2,2 7,7
M12 12,2 20,2 2,5 8,8
M16 16,2 26,2 3,5 12,3
M20 20,2 32,2 4 14
M22 22,5 34,5 4 14
M26 26,5 40,5 5 17,5

37240 Double coil spring lock washer L07D

Material Spring steel
Packaging Standard

Double coil spring lock washer

37240

For nom. size  Art.number For nom. size  Art.number For nom. size  Art.number
M5 100 37240.050.001 M10 100 37240.100.001 M20 50 37240.200.001
M6 100 37240.060.001 M12 100 37240.120.001 M22 25 37240.220.001
M8 100 37240.080.001 M16 50 37240.160.001 M26 25 37240.260.001
Double coil spring lock washer
37240

• Warning: electro-galvanizing of these products may cause hydrogen embrittlement.

121 - www.fabory.com 7-43

 Conical spring washer
DIN 74361 C

Technical data
d d6 d7 h6
M12 12,5 23 5
M14 14,5 26 6
M16 (≠DIN) 17,5 27 7
M18 18,5 29 7
M20 20,5 34 8
M22 22,5 34 8

72030 Conical spring washer Y92E

Material Spring steel DIN17221
Packaging Standard

Conical spring washer

72030

d  Art.number d  Art.number d  Art.number

M12 50 72030.120.001 M16 50 72030.160.001 M20 25 72030.200.001
M14 50 72030.140.001 M18 25 72030.180.001 M22 25 72030.220.001
Conical spring washer
72030

• Usable for wheelbolts

7-44 121 - www.fabory.com

 Wave spring washer
DIN 137 B
NEN 2457
NF E27-620

Technical data
For nom.size d1 d2 s
M3 3,2 8 0,5
M3,5 3,7 8 0,5
M4 4,3 9 0,5
M5 5,3 11 0,5
M6 6,4 12 0,5
M7 7,4 14 0,8
M8 8,4 15 0,8
M10 10,5 21 1
M12 13 24 1,2
M14 15 28 1,6
M16 17 30 1,6
M18 19 34 1,6
M20 21 36 1,6
M22 23 40 1,8
M24 25 44 1,8
M27 28 50 2

Article groups
Material Surface treatment Packaging Code Page
Spring steel DIN267-26 Standard 37160 7-45
Spring steel DIN267-26 Zipl yell.p. Standard 37150 7-45
St.St. A2 Standard 51551 7-46

37160 Wave spring washer L07D

Material Spring steel DIN267-26
Packaging Standard

7
Wave spring washer
37160

For nom. size  Art.number For nom. size  Art.number For nom. size  Art.number
M3 1000 37160.030.001 M8 1000 37160.080.001 M20 100 37160.200.001
M4 1000 37160.040.001 M10 500 37160.100.001 M22 100 37160.220.001
M5 1000 37160.050.001 M12 500 37160.120.001 M24 100 37160.240.001
M6 1000 37160.060.001 M14 100 37160.140.001
M7 1000 37160.070.001 M16 100 37160.160.001

• Spring washers acc. to DIN 137 should be used in combination with fasteners of property class < 5.8, use under dynamic load is not allowed.
• They are intended to counteract the effect of ”play or setting” which results in bolt/nut assemblies working loose (see DIN 267-26).
• They do not effectively prevent loosening of the assembly under varying radial load and are designed for use with short bolts predominantly subject to
thrust.
• For locking under dynamic load is referred to locking edge washers, SCHNORR safety washers and NORD-LOCK vibration proof washers.
• Warning: electro-galvanizing of these products may cause hydrogen embrittlement.
Wave spring washer
37160

37150 Wave spring washer L07D

Material Spring steel DIN267-26
Surface treatment Zinc plated yellow passivated
Packaging Standard

Wave spring washer

37150

For nom. size  Art.number For nom. size  Art.number For nom. size  Art.number
M3 1000 37150.030.001 M7 1000 37150.070.001 M14 100 37150.140.001
M4 1000 37150.040.001 M8 1000 37150.080.001 M16 100 37150.160.001
M5 1000 37150.050.001 M10 500 37150.100.001
M6 1000 37150.060.001 M12 500 37150.120.001

121 - www.fabory.com 7-45

 37150 Wave spring washer 
For nom. size  Art.number For nom. size  Art.number For nom. size  Art.number
• Spring washers acc. to DIN 137 should be used in combination with fasteners of property class < 5.8, use under dynamic load is not allowed.
• They are intended to counteract the effect of ”play or setting” which results in bolt/nut assemblies working loose (see DIN 267-26).
• They do not effectively prevent loosening of the assembly under varying radial load and are designed for use with short bolts predominantly subject to
thrust.
• For locking under dynamic load is referred to locking edge washers, SCHNORR safety washers and NORD-LOCK vibration proof washers.
• Warning: electro-galvanizing of these products may cause hydrogen embrittlement.
Wave spring washer
37150

51551 Wave spring washer R09A

Material Stainless steel A2
Packaging Standard
DIN ≈137 B
NEN ≈2457
NF ≈E27-620

Wave spring washer

51551

For nom. size  Art.number For nom. size  Art.number For nom. size  Art.number
M3 200 51551.030.001 M8 200 51551.080.001 M20 50 51551.200.001
M3,5 1000 51551.035.001 M10 100 51551.100.001 M22 * 100 51551.220.001
M4 200 51551.040.001 M12 100 51551.120.001 M24 50 51551.240.001
M5 200 51551.050.001 M14 * 200 51551.140.001 M27 * 100 51551.270.001
M6 200 51551.060.001 M16 100 51551.160.001
M7 * 500 51551.070.001 M18 * 200 51551.180.001
Wave spring washer
51551

• Use under dynamic load is not allowed.

• For locking under dynamic load is referred to NORD-LOCK vibration proof washers and SCHNORR safety washers.
• The austenetic steel type is at the manufacturer’s discretion, and can vary from the steel types stated in DIN 267-11.

7-46 121 - www.fabory.com

 Curved spring washer DIN 137A
DIN 137 A
NEN 2456

Technical data
For nom.size d1 d2 s h (max.)
M2 2,2 4,5 0,3 1
M2,3 2,5 5 0,3 1
M2,5 (≠DIN) 2,6 5 0,3 1
M2,6 2,8 5,5 0,3 1,1
M3 3,2 6 0,4 1,3
M3,5 3,7 7 0,4 1,4
M4 4,3 8 0,5 1,6
M5 5,3 10 0,5 1,8
M6 6,4 11 0,5 2,2
M7 7,4 12 0,5 2,4
M8 8,4 15 0,5 3,4
M10 10,5 18 0,8 4
• Spring washers acc. to DIN 137 should be used in combination with fasteners of property class < 5.8, use under dynamic load is not allowed.
• They are intended to counteract the effect of ”play or setting” which results in bolt/nut assemblies working loose (see DIN 267-26).
• They do not effectively prevent loosening of the assembly under varying radial load and are designed for use with short bolts predominantly subject to
thrust.
• For locking under dynamic load is referred to locking edge washers, SCHNORR safety washers and NORD-LOCK vibration proof washers.

Article groups
Material Surface treatment Packaging Code Page
Spring steel DIN267-26 Standard 37120 7-47
Spring steel DIN267-26 Zipl yell.p. Standard 37110 7-47

37120 Curved spring washer DIN 137A L07D

Material Spring steel DIN267-26
Packaging Standard
7
Curved spring washer DIN 137A
37120

For nom. size  Art.number For nom. size  Art.number For nom. size  Art.number
M2 500 37120.020.001 M3,5 500 37120.035.001 M7 500 37120.070.001
M2,3 500 37120.023.001 M4 500 37120.040.001 M8 500 37120.080.001
M2,6 500 37120.026.001 M5 500 37120.050.001 M10 200 37120.100.001
M3 500 37120.030.001 M6 500 37120.060.001

• Warning: electro-galvanizing of these products may cause hydrogen embrittlement.

Curved spring washer DIN 137A
37120

37110 Curved spring washer DIN 137A L07D

Material Spring steel DIN267-26
Surface treatment Zinc plated yellow passivated
Packaging Standard

Curved spring washer DIN 137A

37110

For nom. size  Art.number For nom. size  Art.number For nom. size  Art.number
M2 500 37110.020.001 M4 500 37110.040.001 M7 500 37110.070.001
M2,5 500 37110.025.001 M5 500 37110.050.001 M8 500 37110.080.001
M3 500 37110.030.001 M6 500 37110.060.001 M10 200 37110.100.001
Curved spring washer DIN 137A
37110

• Warning: electro-galvanizing of these products may cause hydrogen embrittlement.

121 - www.fabory.com 7-47

 Curved spring lock washer DIN 128A
DIN 128 A
NEN 1570

Technical data
For nom.size d1 (min.) d2 (max.) s
M2 2,1 4,4 0,5
M2,3 (≠DIN) 2,4 4,9 0,6
M2,5 2,6 5,1 0,6
M2,6 (≠DIN) 2,7 5,2 0,6
M3 3,1 6,2 0,7
M3,5 3,6 6,7 0,7
M4 4,1 7,6 0,8
M5 5,1 9,2 1
M6 6,1 11,8 1,3
1/4 (≠DIN) 6,5 12,6 1,3
M7 7,1 12,7 1,3
M8 8,1 14,8 1,6
3/8 (≠DIN) 9,7 17,6 1,8
M10 10,2 18,1 1,8
M11 (≠DIN) 11,3 19,3 2,1
M12 12,2 21,1 2,1
1/2 (≠DIN) 13 22,8 2,4
M14 14,2 24,1 2,4
M16 16,2 27,4 2,8
M18 18,2 29,4 2,8
M20 20,2 33,6 3,2
M22 22,5 35,9 3,2
M24 24,5 40 4
1.IN. (≠DIN) 26,5 42,5 4
M27 27,5 43 4
M30 30,5 48,2 6
M33 (≠DIN) 34 54,2 6
M36 36,5 58,2 6
7 M39 (≠DIN)
M42 (≠DIN)
39,5
42,5
59,2
68,2
6
7
M45 (≠DIN) 46,7 70,5 7
M48 (≠DIN) 49 75 7

Article groups
Material Surface treatment Packaging Code Page
Spring steel DIN267-26 Mech.zipl. Standard 37080 7-48
Spring steel DIN267-26 Zipl yell.p. Standard 37092 7-49
St.St. A2 Standard 51520 7-49
St.St. A4 Standard 55520 7-49
Phosphor bronze Cu4 Standard 50500 7-50

37080 Curved spring lock washer DIN 128A L07D

Material Spring steel DIN267-26
Surface treatment Mechanical zinc plated
Packaging Standard

Curved spring lock washer DIN 128A

37080

For nom. size  Art.number For nom. size  Art.number For nom. size  Art.number
M2 500 37080.020.001 M7 250 37080.070.001 M18 100 37080.180.001
M2,5 500 37080.025.001 M8 200 37080.080.001 M20 100 37080.200.001
M2,6 500 37080.026.001 3/8 200 37080.096.001 M22 50 37080.220.001
M3 250 37080.030.001 M10 200 37080.100.001 M24 50 37080.240.001
M3,5 250 37080.035.001 M11 150 37080.110.001 1.IN. 50 37080.254.001
M4 250 37080.040.001 M12 150 37080.120.001 M27 25 37080.270.001
M5 250 37080.050.001 1/2 150 37080.127.001 M30 25 37080.300.001
M6 250 37080.060.001 M14 100 37080.140.001 M33 25 37080.330.001
1/4 250 37080.063.001 M16 100 37080.160.001 M36 25 37080.360.001

7-48 121 - www.fabory.com

 37080 Curved spring lock washer DIN 128A 
For nom. size  Art.number For nom. size  Art.number For nom. size  Art.number
M39 10 37080.390.001 M45 10 37080.450.001
M42 10 37080.420.001 M48 10 37080.480.001

• Curved spring lock washers acc. to DIN 128 A are improved compared to spring lock washers acc. to DIN 127 A and due to the curved form have
moreover the advantages: do not damage surfaces of the construction, nut or bolt; also to use with left hand thread; do not disform during tightening and
dis-assembly, thus re-useable; do not tangle, so suitable for automatic feeding and should be used in combination with fasteners of property class < 8.8,
use under dynamic load is not allowed.
• For locking under dynamic load is referred to locking edge washers, SCHNORR safety washers and NORD-LOCK vibration proof washers, see
elsewhere in this section.
Curved spring lock washer DIN 128A
37080

37092 Curved spring lock washer DIN 128A L07D

Material Spring steel DIN267-26
Surface treatment Zinc plated yellow passivated
Packaging Standard

Curved spring lock washer DIN 128A

37092

For nom. size  Art.number For nom. size  Art.number For nom. size  Art.number
M4 250 37092.040.001 M8 200 37092.080.001 M14 100 37092.140.001
M5 250 37092.050.001 M10 200 37092.100.001
M6 250 37092.060.001 M12 150 37092.120.001

• Curved spring lock washers acc. to DIN 128 A are improved compared to spring lock washers acc. to DIN 127 A and due to the curved form have
moreover the advantages: do not damage surfaces of the construction, nut or bolt; also to use with left hand thread; do not disform during tightening and
dis-assembly, thus re-useable; do not tangle, so suitable for automatic feeding and should be used in combination with fasteners of property class < 8.8,
use under dynamic load is not allowed.
• For locking under dynamic load is referred to locking edge washers, SCHNORR safety washers and NORD-LOCK vibration proof washers, see
elsewhere in this section.
Curved spring lock washer DIN 128A
37092

51520 Curved spring lock washer DIN 128A R09A

Material Stainless steel A2
Packaging Standard
DIN ≈128 A
NEN ≈1570

Curved spring lock washer DIN 128A

51520

For nom. size  Art.number For nom. size  Art.number For nom. size  Art.number
M2 100 51520.020.001 M6 250 51520.060.001 M20 100 51520.200.001
M2,5
M2,6
100
100
51520.025.001
51520.026.001
M8
M10
200
200
51520.080.001
51520.100.001
M22
M24
50
50
51520.220.001
51520.240.001
7
M3 250 51520.030.001 M12 150 51520.120.001 M30 25 51520.300.001
M3,5 250 51520.035.001 M14 100 51520.140.001 M36 25 51520.360.001
M4 250 51520.040.001 M16 100 51520.160.001
M5 250 51520.050.001 M18 100 51520.180.001

• The measurements deviate slightly from DIN 128 A, these spring lock washers have a deviating ”reinforced” thickness resulting in considerably improved
spring characteristics.
• Curved spring lock washers acc. to DIN 128 A are improved compared to spring lock washers acc. to DIN 127 A and due to the curved form have
moreover the advantages: do not damage surfaces of the construction, nut or bolt; also to use with left hand thread; do not disform during tightening and
dis-assembly, thus re-useable; do not tangle, so suitable for automatic feeding. Use under dynamic load is not allowed.
• For locking under dynamic load is referred to NORD-LOCK vibration proof washers and SCHNORR safety washers.
• The austenetic steel type is at the manufacturer’s discretion, and can vary from the steel types stated in DIN 267-11.
Curved spring lock washer DIN 128A
51520

55520 Curved spring lock washer DIN 128A R49A

Material Stainless steel A4
Packaging Standard
DIN ≈128 A
NEN ≈1570

Curved spring lock washer DIN 128A

55520

For nom. size  Art.number For nom. size  Art.number For nom. size  Art.number
M3 250 55520.030.001 M8 200 55520.080.001 M20 100 55520.200.001
M4 250 55520.040.001 M10 200 55520.100.001 M24 * 100 55520.240.001
M5 250 55520.050.001 M12 150 55520.120.001
M6 250 55520.060.001 M16 100 55520.160.001

• The measurements deviate slightly from DIN 128 A, these spring lock washers have a deviating ”reinforced” thickness resulting in considerably improved
spring characteristics.
• Curved spring lock washers acc. to DIN 128 A are improved compared to spring lock washers acc. to DIN 127 A and due to the curved form have
moreover the advantages: do not damage surfaces of the construction, nut or bolt; also to use with left hand thread; do not disform during tightening and
dis-assembly, thus re-useable; do not tangle, so suitable for automatic feeding.
• Use under dynamic load is not allowed. For locking under dynamic load is referred to NORD-LOCK vibration proof washers and SCHNORR safety
washers.

121 - www.fabory.com 7-49

 55520 Curved spring lock washer DIN 128A 
For nom. size  Art.number For nom. size  Art.number For nom. size  Art.number
• The austenetic steel type is at the manufacturer’s discretion, and can vary from the steel types stated in DIN 267-11.
Curved spring lock washer DIN 128A
55520

50500 Curved spring lock washer DIN 128A M11F

Material Phosphor bronze Cu4
Packaging Standard
DIN ≈128 A
NEN ≈1570

Curved spring lock washer DIN 128A

50500

For nom. size  Art.number For nom. size  Art.number For nom. size  Art.number
M2,6 500 50500.026.001 M6 250 50500.060.001 M16 100 50500.160.001
M3 250 50500.030.001 M8 200 50500.080.001 M18 100 50500.180.001
M4 250 50500.040.001 M10 200 50500.100.001 M20 100 50500.200.001
M5 250 50500.050.001 M12 150 50500.120.001
Curved spring lock washer DIN 128A
50500

• The measurements deviate slightly from DIN 128 A, these spring lock washers have a deviating ”reinforced” thickness resulting in considerably improved
spring characteristics.

7-50 121 - www.fabory.com

 Locking edge washer ≈ DIN 128A
DIN ≈128 A
NEN ≈1570

Technical data
For nom.size d1 d2 (max.) s
M4 4,1 7,6 0,8
M5 5,1 9,2 1
M6 6,1 11,8 1,3
M8 8,1 14,9 1,6
M10 10,2 18,1 1,8
M12 12,2 21,1 2,1
M14 14,2 24,1 2,4
M16 16,2 27,4 2,8
M18 18,2 29,4 2,8
M20 20,2 33,6 3,2
M22 22,5 35,9 3,2
M24 24,5 40 4
M27 27,5 43 4
M30 30,5 48,2 6

Special features of FABORY locking edge washers:

- apllicable with hexagon head bolts, hexagon nuts, etc. of property class ” 8.8
- the profile surface (patented) ensures good locking against loosening properties and reduces loss of assembly pre-load
- compensation against play or setting of the joint by a long spring deflection
- little damage, so also usable with softer materials and surface coatings
- re-usable
- suited for automatic installation
- insensitive for temperature from -10°C up to +300°C
- sizes and other properties according to DIN 128 A
- simple application together with current standard fasteners
- also applicable for hexagon head bolts, hexagon nuts etc. with left-hand thread

37070 Locking edge washer L07D

Material Spring steel DIN267-26
Surface treatment Mechanical zinc plated yellow passivated
Packaging Standard

Locking edge washer

37070

For nom. size  Art.number For nom. size  Art.number For nom. size  Art.number
M4 250 37070.040.001 M12 150 37070.120.001 M22 50 37070.220.001
M5 250 37070.050.001 M14 100 37070.140.001 M24 50 37070.240.001
M6 250 37070.060.001 M16 100 37070.160.001 M27 25 37070.270.001
M8 200 37070.080.001 M18 100 37070.180.001 M30 25 37070.300.001
M10 200 37070.100.001 M20 100 37070.200.001
Locking edge washer

121 - www.fabory.com 7-51