Notes:-
1. All dimensions to be checked on site, written
dimensions to be followed in preference to scaled
dimensions.
2. All walls less than 200mm thick to be reinforced with
6,300 6,700
hoop iron at every alternate course.
03
A
3. All reinforced concrete work is to be in accordance
200 200 2,850 200 2,850 200 200 with structural engineer's details.
200
200
6,100 4. All sanitary work to be in accordance with M.O.H rules
5,898 and regulations.
Foundation trench Container outline 5. Where drain passes under building or driveway
200
area,pipe to be of cast iron or encased in 150mm
concrete.
200
6. All waste pipes and soil pipes are to be in ducts and
2,352
200
Direction of flow
the bends to have all cleaning eyes accessible from
200 200 200
of rainwater
outside.
3,340
200 200 2,450 200 200 2,450 200 200 OFFICE SPACE 7. All windows and external glazed doors on ground floor
04
02
to have burglar proofing to Architect's detail.
2,640
2,440
1,840
2,240
(In a 20ft container)
HARDCORE HARDCORE 1500x2100mm 8. All door frames to be rebated & moulded & be full
1500x1200 mm (WxH) width of wall with moulded architrave to detail, provide
Steel & Glass door rubber door stops to all doors.
300
Steel & Glass window
Roof pitch - 3deg 9. Stair case and lobby doors to be self closing and 1/2
200
Galvanised roofing sheets hour fire resistant.
200
10. All internal plaster to be two coats steel float finished.
300
Foundation trench
200
11. All manholes within building area, driveway and
parking to have heavy duty air tight covers and double
Foundation trench GROUND FLOOR PLAN sealed.
200
200
300
RC Stub column the
01 ROOF PLAN 12. Provide G.I. 125 x 100 rainwater down pipes and125 x
A
100 [Link] gutter with brackets etc. where shown.
height of the plinth walls
FOUNDATION PLAN 13. All painting to be 3 coats.
14. Splash apron of 1000mm along the perimeter of
building.
15. Samples of fittings, materials etc. to be produced &
approved before commencing work.
16. All windows to have P.C. cills, built in reinforced
concrete Pelmet boxes & timber internal window cills &
Skirtings.
17. Steel trusses/portal frames & purlins to be painted
with 2 coats of oil paint.
ROOF LVL ROOF LVL
18. Fire fighting equipment to be provided and installed
Roof notes 1,500 1,000 1,500 by Building Fire Consultants where shown on plan.
Roof pitch 25 degrees [Link] architectural drawings shall be read in
conjunction with the Structural drawings,Electrical-
Clay roofing tiles Mechanical drawings, Bills of Quantities & Technical
1,200
Ridge caps to match roof type Specifications. Any discrepancy shall be reported
immediately to the Architect.
100x50mm timber purlins on
2,590
2,590
150x50mm rafters on
2,100
100x50mm Strut & Tie on
20. The Architect shall not accept any liability for works
150x50mm Tie beam on which he has not been expressly instructed to Supervise
150x75mm wall plate and in writing and has accepted to proceed in writing, or
225x25mm Fascia board for any ommissions or deviations from his
drawings/technical specifications.
Nor shall he take responsibility for works handled by
150
150
other nominated Consultants or Contractors.
ROOF LVL
GROUND FLOOR LVL GROUND FLOOR LVL
150
450
150
450
Client:
150
150
ELEVATION 01 ELEVATION 02
2,590
2,590
OFFICE
SPACE CLIENT'S SIGNATURE...............................................
ROOF LVL ROOF LVL
100
150
GROUND FLOOR LVL
150
350
150
Project Name and Address:
PROPOSED OFFICE DEVELOPMENT TO BE
BUILT ON PLOT , BLOCK , ENTEBBE,
2,590
2,590
600
200
WAKISO DISTRICT
Foundation notes
100mm thick concrete floor slab to SE's details on
1000g polythene sheet water proofing,
50mm thick on murram blinding on
well compacted hardcore fill
Foundation depth to be determined on site SECTION A-A
150
GROUND FLOOR LVL GROUND FLOOR LVL Drawing Title:
TECHNICAL DOCUMENTATION
450
150
150
Job no: Drwg no:
ELEVATION 03 ELEVATION 04
Scales: 1:20, 1:50,
1:100
REVISIONS
Drawn by: No: Date Descriptions
MA
Checked by:
Date:
MARCH - 2025
GSPublisherVersion [Link]
