MILLIPORE

Page 1/36

Operating and
Maintenance Manual

Simplicity™
Water Purification System

MILLIPORE
Page 1/36

Operating and
Maintenance Manual
 Page 2/36

NOTICE ___________________________________________
Information in this document is subject to change without notice and should not be construed as a
commitment by Millipore Corporation. Millipore Corporation assumes no responsibility for any er-
rors that may appear in this document. This manual is believed to be complete and accurate at the
time of publication. In no event shall Millipore Corporation be liable for incidental or consequential
damages in connection with or arising from the use of this manual.

Copyright © 2004, all rights reserved, Millipore Corporation.

User manual: PF06022 (Rev. 1 - 05/04)

Manufacturer : MILLIPORE S.A.S., 67120 MOLSHEIM, FRANCE

Trademarks
Millipore is a registered trademark of Millipore Corporation or an affiliated company.
Simplicity, Elix, SimPak and SimFilter are trademarks of Millipore Corporation.
All other trademarks are trademarks of their respective manufacturer.

Congratulations on your purchase of the Simplicity Ultrapure Water System. This system has been
manufactured using state-of-the-art technologies and the highest quality components to insure years
of reliable performance. The system has been designed to be extremely easy-to-use and maintain.
This manual contains important safety information so we urge you to please read it thoroughly
before using the system. If you should have any questions or comments on this system, please
contact your local Millipore representative or visit our web site at http://www.millipore.com.

Page 2/36

NOTICE ___________________________________________
Information in this document is subject to change without notice and should not be construed as a
commitment by Millipore Corporation. Millipore Corporation assumes no responsibility for any er-
 Page 3/36

___________________________ DECLARATION OF CONFORMITY

DECLARATION OF CONFORMITY
EUROPEAN UNION EC DIRECTIVES

Directive 89/336/CEE
Directive 73/23/CEE

◆ These Lab Water Systems are designed and manufactured in application of the following
European Council directives :

– 89/336/CEE relating to Electromagnetic compatibility

– 73/23/CEE relating to electrical equipment designed for use within certain voltage
limits

◆ Standards to which conformity is declared as applicable are the following :

– EN 55022-1 : 1992
– EN 50082-1 : 1994

– EN 61010-1 : 1993 /A2 : 1995

Page 3/36

___________________________ DECLARATION OF CONFORMITY

DECLARATION OF CONFORMITY
EUROPEAN UNION EC DIRECTIVES
Cleaning ........................................................................................................... 16
System maintenance messages ............................................................................ 16
Page 4/36

TABLE OF CONTENTS _____________________________________

GETTING STARTED
HOW TO USE THIS MANUAL ............................................................... 6
Warnings ............................................................................................................ 6
Illustrations .......................................................................................................... 6
INTRODUCTION .................................................................................. 7
General Information ............................................................................................. 7
System performance ........................................................................................ 8
Environmental Conditions ................................................................................. 9
Electrical Operating Conditions ........................................................................ 9
Composition of materials in contact with water .................................................. 9
Dimensions and weight .................................................................................. 10
Safety information ......................................................................................... 10
INSTALLATION .................................................................................. 11
Unpacking ........................................................................................................ 11
Selecting a site for the Simplicity system ............................................................... 11
Filling the Integral Reservoir ................................................................................ 12
Installing the Reservoir Vent Filter ........................................................................ 12
Installating the purification Pack .......................................................................... 12
Electrical connection .......................................................................................... 13
Language Selection ............................................................................................ 13
Purging the Pak ................................................................................................. 14
Installing the SimFilter ........................................................................................ 14
STANDARD OPERATING OF THE SIMPLICITY ....................................... 15
Maintaining a minimum level of water in the reservoir .......................................... 15
Standard displayed messages ............................................................................. 15
Cleaning ........................................................................................................... 16
System maintenance messages ............................................................................ 16

Page 4/36

TABLE OF CONTENTS _____________________________________

GETTING STARTED
HOW TO USE THIS MANUAL ............................................................... 6
Warnings ............................................................................................................ 6
 Page 5/36

_____________________________________ TABLE OF CONTENTS

MORE ABOUT SIMPLICITY
USE OF THE KEYPAD ......................................................................... 17
Standard menu .................................................................................................. 17
Consumable lifetime ........................................................................................... 18
Choosing the non-temperature compensated resistivity display .............................. 19
Selecting the unit of measure .............................................................................. 20
Setting the displayed language ........................................................................... 21
UV lamp reset (Only for Simplicity 185) .............................................................. 21
MAINTENANCE ................................................................................. 22
Replacing the consumables ................................................................................. 22
Replacing the UV lamp (Only for Simplicity 185) ................................................. 23
UV Lamp replacement .................................................................................... 23
UV lamp reset ............................................................................................... 24
Shutting down the system for an extended period of time ...................................... 25
TROUBLESHOOTING ......................................................................... 26
Troubleshooting table ......................................................................................... 26
ORDERING INFORMATION ................................................................ 28
Millipore’s Standard Warranty ............................................................................ 29
ILLUSTRATIONS ................................................................................. 30
At the back of the document: ILLUSTRATIONS and TECHNICAL ASSISTANCE

Page 5/36

_____________________________________ TABLE OF CONTENTS

MORE ABOUT SIMPLICITY
USE OF THE KEYPAD ......................................................................... 17
Standard menu .................................................................................................. 17
 Page 6/36

HOW TO USE THIS MANUAL ______________________________

This manual describes how to install, maintain and use the Simplicity.
It is recommended that this document is completely read before
plugging in the unit to a source of electrical power. The system is easy
to use and to maintain. However, it is wise to be familiar with all its
functions as described in this manual.

Warnings _______________________________________________

Warning and Attention symbols will be placed near text when

important information is present.

: Attention (Important Details)

: Refer to Documentation

Illustrations _____________________________________________

Illustrations are referenced in the text and are located in the back
of this manual.

Page 6/36

HOW TO USE THIS MANUAL ______________________________

This manual describes how to install, maintain and use the Simplicity.
It is recommended that this document is completely read before
plugging in the unit to a source of electrical power. The system is easy
 Dispensing valve button 4
Front panel with Liquid Crystal Display and Keypad 5
Page 7/36

_________________________________________ INTRODUCTION
General Information ______________________________________

Simplicity is a water purification

system fed through an integrated
vented storage reservoir. The system 5 1
provides the final “polish” to remove
any remaining contaminants in water 2
pretreated by reverse osmosis, 4
electrodeionization (Elix), distillation
or deionization.
The Simplicity system is designed to 3
produce water of Type 1 quality.
This is equal to or better than ASTM,
CAP and NCCLS Type 1 water
quality standards.

Reservoir 1
SimPak locking handle 2
SimPak 3
Dispensing valve button 4
Front panel with Liquid Crystal Display and Keypad 5
Page 7/36

_________________________________________ INTRODUCTION
General Information ______________________________________

Simplicity is a water purification

 Page 8/36

INTRODUCTION _________________________________________
System performance

Purified water quality

Simplicity Simplicity 185

Resistivity 18.2 MΩ-cm at 25 °C 18.2 MΩ-cm at 25 °C

TOC* 15 ppb 5 ppb

Micro-organisms ≤ 1 cfu/ml ≤ 1 cfu/ml

Particles (0.22 µm) < 1 / ml < 1 / ml
Flowrates

Typical product water flowrate Up to 0.5 L/mn 0.5 L/mn

Sound level 48 dB A at 1 metre 48 dB A at 1 metre

* Test conditions: System was equipped with a SimPak 1 purification

Pack. The feedwater for the reservoir came from an Elix system.
TOC in the feedwater was < 50 ppb. The quality of the product
water can vary as a function of the quality of the feedwater.

Page 8/36

INTRODUCTION _________________________________________
System performance

Purified water quality

 housing: Ultrapure Quartz, SST

Page 9/36

_________________________________________ INTRODUCTION
Environmental Specifications
Storage temperature -40°C to 70°C at 5% to 80% RH
Operating temperature 5°C to 35°C at 5% to 80% RH
Feed water temperature 5°C to 30°C at 5% to 80% RH
Altitude range 2000 meters

This equipment is designed to be used in installation/overvoltage category II and pollution degree II.

Electrical Operating Conditions

Electrical consumption 30 VA
Electrical voltage 100, 120 VAC +/– 10%, 50/60 HZ +/– 3%
UV lamp lifetime after installation 2 years (700 days)

Main power cord length 2.4 meters / 8.3 feet

Composition of materials
Part Material Part Material
Pack adapter: PE Final Filter: Polycarbonate, Polysulfone
Pack: PP Fitting: PE, PA,
3.5 L reservoir: HDPE Resistivity cell: Stainless steel 316 L
Reservoir adapter: POM
Pump head: PP, Santoprene® Tubing: PE
Three way valve: PP, POM
UV lamp and O-rings: EPDM
housing: Ultrapure Quartz, SST

Page 9/36

_________________________________________ INTRODUCTION
Environmental Specifications
Storage temperature -40°C to 70°C at 5% to 80% RH
Operating temperature 5°C to 35°C at 5% to 80% RH
 Page 10/36

INTRODUCTION _________________________________________
Dimensions and weight
Height 460 mm (18.11 inches)
Length 248 mm (9.76 inches)
Depth 345 mm (13.58 inches)
Weight of dry system in his box Simplicity: 5.7 Kg (12.7 lbs)
Simplicity 185: 6.3 Kg (14.0 lbs)
Operating weight with full reservoir Simplicity:10.4 Kg (23.1 lbs)
Simplicity 185: 11.1 Kg (24.6 lbs)
Space required to remove and
install the reservoir. 20 cm around the unit (0.5 inches)

Safety information

: Danger!

: Electrical Danger!

: Ground Connection!

: Danger : UV Radiation!

Page 10/36

INTRODUCTION _________________________________________
Dimensions and weight
Height 460 mm (18.11 inches)
Length 248 mm (9.76 inches)
 to the space needed to remove and install the reservoir.
Page 11/36

___________________________________________ INSTALLATION
Unpacking ______________________________________________

After unpacking the shipping container you should find (Figure 2):
Present?
Yes No

(A) Simplicity water purification system with reservoir

(B) User manual
(C) Point-of-use valve hose barb connector for purging a new SimPak
Ordered separately
(D) SimPak purification pack
(E) Reservoir vent filter
(F) SimFilter

Selecting a site for the Simplicity system _____________________

Warning: Do not plug in the electrical power cord into

a power source at this step.

The Simplicity system has been designed to be placed on any

laboratory bench (or suitable alternative). See the section
“Dimensions” page 10 of this manual for information related
to the space needed to remove and install the reservoir.

Page 11/36

___________________________________________ INSTALLATION
Unpacking ______________________________________________

After unpacking the shipping container you should find (Figure 2):
 Page 12/36

INSTALLATION ___________________________________________
Filling the Integral Reservoir _______________________________
Figure 3
1. Raise the reservoir-locking handle to vertical position. (A)
2. Pull out the reservoir (B) using the locking handle.
3. Remove the reservoir cap (C) by twisting counter-clockwise 1/4 turn.
4. Fill the reservoir, re-install it and secure the locking handle into the body of the system.

Installing the Reservoir Vent Filter ___________________________

1. Install the Reservoir vent filter (D) into the reservoir cap.
2. Replace the reservoir cap by twisting clockwise 1/4 turn

Installating the purification Pack ____________________________

Figure 4
1. Swing the Pack locking handle to the left by pressing on the locking tab (A).
2. Remove the two protective caps on the Simplicity connector (B).
3. Remove the two protective caps on the SimPak cartridge (C), Wet the two O-rings of the
Pack with a few drops of water.
4. Push the SimPak (D) firmly into the unit.
5. Secure the pak in place by closing the locking handle (E). The locking handle should
engage easily. If you need to force the handle, then the pack is not fully positioned into
the pack adapter.

Page 12/36

INSTALLATION ___________________________________________
Filling the Integral Reservoir _______________________________
Figure 3
1. Raise the reservoir-locking handle to vertical position. (A)
 To accept and go back to normal operating mode,
press MENU button for 1 sec.

Page 13/36

___________________________________________ INSTALLATION
Electrical connection ______________________________________

The electrical wall outlet must be accessible in the event that the Simplicity must be
unplugged quickly. To turn off the Simplicity, remove the power cord from the wall
outlet. The AC plug is the main disconnect for the system.

1. Connect the power cord to a grounded power source.

2. If necessary, put the system in STANDBY mode by depressing the OPERATE/STANDBY
button for two seconds.
3. Check that the point of use valve knob is in the upright position (closed).

Language Selection _______________________________________

It is possible to change the displayed language on the LCD. The choices for the languages are
English, French (Français), German (Deutsch), Spanish (Español), Italian (Italiano) and Japanese
(( ).

0PERATE DISPLAY MENU

In either OPERATE or STANDBY mode, PACK AGE
press MENU for at least 2 seconds. 30 DAYS

0PERATE DISPLAY MENU

SET LANGUAGE
Press MENU several times to display ENGLISH

0PERATE DISPLAY MENU Press DISPLAY to change between: English, SET LANGUAGE
French, German, Italian, Spanish or Japanese FRANCAIS

To accept and go back to normal operating mode,

press MENU button for 1 sec.

Page 13/36

___________________________________________ INSTALLATION
Electrical connection ______________________________________

The electrical wall outlet must be accessible in the event that the Simplicity must be
unplugged quickly. To turn off the Simplicity, remove the power cord from the wall
 The system is now ready to produce high quality water.

Page 14/36

INSTALLATION ___________________________________________
Purging the Pak __________________________________________
1. Install the connector (Figure 2,C) into the POU valve.

Note: Do not use Teflon tap on the connector tread. The seat of the valve contains
an O-ring seal.
The part should turn easily. Do not force, otherwise the valve thread could be
damaged.

2. Position a container under the outlet fitting.

3. Move the dispensing valve button down to open the valve.
4. Press the OPERATE button to switch from STANDBY to OPERATE mode.
5. After having drawn 1-2 litres of water from the system, close the valve.
6. If possible, leave the system in STANDBY mode overnight. This helps to hydrate the ion
exchange resin inside the SimPak. This procedure is requested each time a new SimPak is
installed.

Installing the SimFilter ____________________________________

Figure 5
1. Remove the connector (A) from the POU valve if installed.
2. Install the SimFilter (B) into the POU valve.

Note: Do not use teflon tape on the threading.

3. Press the OPERATE button to go from STANDBY to OPERATE mode.

4. Open the POU valve and draw around 0.5 litre of water through the SimFilter.
5. Switch the unit to STANDBY mode.

The system is now ready to produce high quality water.

Page 14/36

INSTALLATION ___________________________________________
Purging the Pak __________________________________________
1. Install the connector (Figure 2,C) into the POU valve.
 Page 15/36

__________________ STANDARD OPERATING OF THE SIMPLICITY

The simplicity system should be used in the manner specified by this user’s manual, otherwise the
protection provided by this equipment may be impaired.

Maintaining a minimum level of water in the reservoir _________

The simplicity is fed through the reservoir located at the back of the unit. Whenever the water in the
reservoir reaches half a liter level it is recommended to refill it.

If the simplicity runs out of water, proceed as follows:

1. Press the OPERATE button to go from OPERATE to STANDBY mode.

2. Refill the reservoir.
3. Replace the SimFilter by the hose barb connector and start the unit.
4. Open the POU valve, press OPERATE and draw approximately 0.2 litre of water.
5. Re-install the SimFilter.

Standard displayed messages _____________________________

Your Simplicity system has a number of operating modes which can be activated via the keypad.
Other modes are automatically activated by the microprocessor.

Page 15/36

__________________ STANDARD OPERATING OF THE SIMPLICITY

The simplicity system should be used in the manner specified by this user’s manual, otherwise the
protection provided by this equipment may be impaired.

Maintaining a minimum level of water in the reservoir _________

See section “Troubleshooting” pages 26 and 27.

Page 16/36

STANDARD OPERATING OF THE SIMPLICITY __________________

These different modes are displayed on the screen, and are described below:

OPERATING STATUS OF SYSTEM

MODE DISPLAY

STANDBY While in this mode, the system is not producing purified water.
Periodic recirculation is performed.

OPERATE System is running. Purified water can be delivered by opening the

PROD:18.2 MΩ.cm dispensing valve.

RECIRCULATION In STANDBY mode, the system automatically recirculates the water

5 mn every 3 hours in order to maintain the water quality during
periods of non-use.

OPERATE System is running and displays the water temperature instead of

TEMP.19°C the resistivity.

OPERATE System is running. Purified water can be delivered. Resistivity

19.8 MΩ.cm 22.9°C measure is not compensated at 25 °C. Water resistivity and
temperature are displayed permanently.

Cleaning ________________________________________________
The exterior of the Simplicity may be cleaned using a soft cloth dampened with a mild detergent.
Prior to cleaning assure that the system main AC power has been disconnected.

System maintenance messages _____________________________

See section “Troubleshooting” pages 26 and 27.

Page 16/36

STANDARD OPERATING OF THE SIMPLICITY __________________

These different modes are displayed on the screen, and are described below:

OPERATING STATUS OF SYSTEM

MODE DISPLAY
 Page 17/36

_____________________________________ USE OF THE KEYPAD

The keypad allows the user to activate the different operating
modes and to review information about consumables lifetime and
system configuration.

Standard menu __________________________________________

KEYPAD ACTION DISPLAY

STANDBY and OPERATE

0PERATE DISPLAY MENU

Press the OPERATE keypad to switch between STANDBY

these two modes

STANDBY

OPERATE
OPERATE
In OPERATE mode the system is ready to PROD: 18.2MΩ. cm
deliver water through the dispensing valve
MEASURE

0PERATE DISPLAY MENU

Press the DISPLAY button during OPERATE or OPERATE

STANDBY mode to display the water temperature. TEMP: 24.2°C

(Temperature display will be replaced by

resistivity after 3 seconds).

Page 17/36

_____________________________________ USE OF THE KEYPAD

The keypad allows the user to activate the different operating
modes and to review information about consumables lifetime and
system configuration.
 Page 18/36

USE OF THE KEYPAD ______________________________________

Consumable lifetime ______________________________________
KEYPAD ACTION DISPLAY

PAK LIFETIME
0PERATE DISPLAY MENU
In either OPERATE or STANDBY mode, PACK AGE
45 DAYS
press MENU for at least 2 seconds

(The pak must be replaced after a maximum 365 days in service)

UV LAMP USE (only Simplicity 185)

0PERATE DISPLAY MENU UV LAMP AGE

9 DAYS
Press MENU once more to display the
UV lamp age.
To go back to normal operating mode,
maintain MENU button for 2 sec.

(The UV lamp must be replaced after a maximum 700 days in service)

Page 18/36

USE OF THE KEYPAD ______________________________________

Consumable lifetime ______________________________________
KEYPAD ACTION DISPLAY
 Page 19/36

_____________________________________ USE OF THE KEYPAD

Choosing the non-temperature compensated resistivity display __
KEYPAD ACTION DISPLAY

0PERATE DISPLAY MENU PACK AGE

In either OPERATE or STANDBY mode, 45 DAYS

press MENU for at least 2 seconds

0PERATE DISPLAY MENU

TEMP.CORRECTION
Press MENU button until it displays. ON

0PERATE DISPLAY MENU

TEMP.CORRECTION
Press DISPLAY once to select Temperature OFF
correction OFF.

0PERATE DISPLAY MENU STANDBY

To accept and go back to normal operating
mode, press MENU button for 2 sec.

OPERATE
19.8 Ω cm 22.9°C
(Example of displays in Operate mode)

Page 19/36

_____________________________________ USE OF THE KEYPAD

Choosing the non-temperature compensated resistivity display __
KEYPAD ACTION DISPLAY

0PERATE DISPLAY MENU

 Page 20/36

USE OF THE KEYPAD ______________________________________

Selecting the unit of measure ______________________________
KEYPAD ACTION DISPLAY

0PERATE DISPLAY MENU In either OPERATE or STANDBY mode PACK AGE

Press MENU for at least 2 seconds. 45 DAYS

0PERATE DISPLAY MENU

Press several times MENU to display. PRODUCTION UNIT
MΩ . cm

0PERATE DISPLAY MENU

Press DISPLAY once to select MΩ.cm (resistivity) PRODUCTION UNIT
or µS/cm (conductivity). µS / cm

To accept and go back to normal operating mode,

press MENU button for 2 sec.

Page 20/36

USE OF THE KEYPAD ______________________________________

Selecting the unit of measure ______________________________
KEYPAD ACTION DISPLAY
 Page 21/36

_____________________________________ USE OF THE KEYPAD

Setting the displayed language _____________________________
KEYPAD ACTION DISPLAY
0PERATE DISPLAY MENU
In either OPERATE or STANDBY mode PACK AGE
45 DAYS
Press MENU for at least 2 seconds.

0PERATE DISPLAY MENU SET LANGUAGE

Press MENU several times to display
ENGLISH

0PERATE DISPLAY MENU Press DISPLAY to change between: SET LANGUAGE

English, French, German, Italian, Spanish ESPAGNOL
or Japanese

0PERATE DISPLAY MENU STANDBY

To accept and go back to normal operating

mode, press MENU button for 1 sec

UV lamp reset (Only for Simplicity 185) _____________________

See “Maintenance” chapter page 23.

Page 21/36

_____________________________________ USE OF THE KEYPAD

Setting the displayed language _____________________________
KEYPAD ACTION DISPLAY
0PERATE DISPLAY MENU PACK AGE
 Page 22/36

MAINTENANCE __________________________________________
Replacing the consumables ________________________________
1. Put the Simplicity into STANDBY mode by pressing the OPERATE button. Do not turn off
the electrical power to the system.
2. Remove the old SimFilter ( Figure 5,B) from the Point of Use valve.
3. Open the Point Of Use valve for a few seconds to depressurize the system.
4. Swing the Pack locking handle (Figure 4,E) to the left by pressing on the locking tab (4,A).
5. Remove the old SimPak (4,D).
6. Remove the two protective caps on the new SimPak. Wet the two O-rings on the pak with
a few drops of water.
7. Push the new SimPak firmly into the unit.
8. Secure the place by closing the locking handle (4,E).
9. Remove the reservoir cap (3,C) and install the Millex vent filter (3,D), shipped with the
SimPak into the inner connector of the reservoir cap.
10. Install the connector (Figure 2,C) into the POU valve.

Note: Do not use Teflon tap on the connector tread

11. Position a container under the outlet fitting.

12. Move the dispensing valve button down to open the valve.
13. Press the OPERATE button to switch from STANDBY to OPERATE mode.
14. After having drawn 1-2 litres of water from the system, close the valve.
15. If possible, leave the system in STANDBY mode overnight. This helps to hydrate the ion
exchange resin inside the SimPak. This only needs to be followed each time a new SimPak
is installed.
16. Remove the connector (Figure 5,A) from the POU valve if installed.
17. Install the SimFilter (5,B) into the POU valve. Do not use teflon tape on the threading.

Page 22/36

MAINTENANCE __________________________________________
Replacing the consumables ________________________________
1. Put the Simplicity into STANDBY mode by pressing the OPERATE button. Do not turn off
the electrical power to the system.
 Page 23/36

_________________________________________ MAINTENANCE
18. Press the OPERATE button to go from STANDBY to OPERATE mode
19. Open the POU valve and draw around 0.5 litre of water through the SimFilter.
20. Switch the unit to STANDBY mode.

The SimFilter should be changed whenever the product flowrate becomes too low (< 0.3 Litres/mn)
or whenever the SimPak is replaced. The lifetime of the SimFilter is dependent upon the quality of the
feedwater and dependent upon the amount of water dispensed through the unit. It is recommended
to replace the filter during replacement of the SimPak.

Replacing the UV lamp (Only for Simplicity 185) ______________

The UV lamp should be replaced every second year. The age of the UV lamp can be checked during
normal use. See “Consumable lifetime” page 18.
When, the message “EXCHANGE UV LAMP” is displayed, proceed as follows.

UV Lamp replacement
Note: The used UV lamp contains metallic mercury and should therefore be
disposed of by the owner, in agreement with local regulations.

1. Put the Simplicity into STANDBY mode by pressing the OPERATE button. Unplug the
electrical power cord from the power source.
2. Open the Point of Use valve for a few seconds to depressurise the system.
3. Swing the Pack locking handle (Figure 4,E) to the left by pressing on the locking tab
(Figure 4,A).
4. Remove the SimPak.

Page 23/36

_________________________________________ MAINTENANCE
18. Press the OPERATE button to go from STANDBY to OPERATE mode
19. Open the POU valve and draw around 0.5 litre of water through the SimFilter.
20. Switch the unit to STANDBY mode.

The SimFilter should be changed whenever the product flowrate becomes too low (< 0.3 Litres/mn)
 Page 24/36

MAINTENANCE __________________________________________
WARNING: Verify that there is no electrical power going to the Pack at this time.
Accidental exposure to Ultraviolet light can cause damage to the eyes
and skin.

5. Push the UV lamp clip to the left and remove it (Figure 6,A).
6. The UV lamp can now be removed from the housing (Figure 6,B). Using the new UV
Lamp, follow steps 1-5 in reverse order.

Note: Use the gloves to avoid getting fingerprints on the new UV lamp.

UV lamp reset
KEYPAD ACTION DISPLAY

0PERATE DISPLAY MENU PACK AGE

In either OPERATE or STANDBY mode,
45 DAYS
press MENU for at least 2 seconds

0PERATE DISPLAY MENU

UV COUNTER RESET
Press MENU several times to display
VALID:OP SWITCH

0PERATE DISPLAY MENU STANDBY

Maintain OPERATE button for at least 10 sec.
to reset the UV lamp age.
The unit goes automatically back to
STANDBY mode.

Page 24/36

MAINTENANCE __________________________________________
WARNING: Verify that there is no electrical power going to the Pack at this time.
Accidental exposure to Ultraviolet light can cause damage to the eyes
and skin.

5. Push the UV lamp clip to the left and remove it (Figure 6,A).
 Page 25/36

_________________________________________ MAINTENANCE
Shutting down the system for an extended period of time ______

Keep the Simplicity in STANDBY mode when water is not needed

for a few days. In this mode, the unit will operate all cycles to keep
the water quality optimum.
If the Simplicity is to be shut down for a long time, drain the
reservoir, remove the SimPak and Simfilter, and unplug the system.
Upon start-up, new cartridges should be installed. For further
information, please contact Millipore Technical Service.

Page 25/36

_________________________________________ MAINTENANCE
Shutting down the system for an extended period of time ______

Keep the Simplicity in STANDBY mode when water is not needed

 Page 26/36

TROUBLESHOOTING ______________________________________
Troubleshooting table _____________________________________
Whenever the Yellow SERVICE LED is blinking, a message is displayed on the screen, which indicates
the nature of the service needed.

STATUS / PROBLEM CAUSE REMEDY

There is no electrical power to - No electrical power. Check the source of power.

the system. - The power cord is not plugged Check the power cord.
into the wall.

The Simplicity system is in - The tank is empty. Fill the tank.

PRODUCT mode but does not - Tank is not well positioned Check tank position
produce any or very little water. - Clogged Point of use filter. Replace the SimFilter
- Tank vent filter plugged Remove tank lid. If flowrate is
OK, replace the vent filter.
- Air is trapped in the SimPak Remove the SimFilter, purge
and the SimFilter. the system.

The system switches The simplicity is pre-set to Re-fill the reservoir if necessary
automatically from produce continuously for and press on OPERATE button.
PRODUCTION mode to 10 min. maximum.
mode to STANDBY mode.

RESISTIVITY < SP The reservoir is empty Fill the reservoir

Resistivity is below the Set Point Install new purification
cartridges.

Page 26/36

TROUBLESHOOTING ______________________________________
Troubleshooting table _____________________________________
Whenever the Yellow SERVICE LED is blinking, a message is displayed on the screen, which indicates
the nature of the service needed.
 Page 27/36

_____________________________________ TROUBLESHOOTING
STATUS / PROBLEM CAUSE REMEDY

EXCHANGE PACK. The operational lifetime of the Change the purification pack.
purification Pack has expired.

PACK OUT The Pak has not been installed Put the Pack back in place.
properly or has been removed.

EXCHANGE UV LAMP The operational lifetime of the Replace the UV lamp

UV lamp has expired.

CHECK UV LAMP Defective UV lamp Occurs when the UV lamp

doesn’t light anymore.

EEPROM ERROR The unit needs to be initialised Press the OPERATE button twice

Page 27/36

_____________________________________ TROUBLESHOOTING
STATUS / PROBLEM CAUSE REMEDY

EXCHANGE PACK. The operational lifetime of the Change the purification pack.
purification Pack has expired.
 Page 28/36

ORDERING INFORMATION ________________________________

Systems

Simplicity Water Purification System, 230 V 50 Hz SIMS50000

Simplicity Water Purification System, 115 V 60 Hz SIMS60000

Simplicity 185 Water Purification System, 230 V 50 Hz SIMS5V000

Simplicity 185 Water Purification System, 115 V 60 Hz SIMS6V000

Consumables

SimPak 1 Kit, for Distilled, RO or Elix feed SIMPAKKR1

(Includes SimPak 1, SimFilter and Vent Filter)
SimPak 2 Kit, for DI feed SIMPAKKD2
(Includes SimPak 2, SimFilter and Vent Filter)
SimPak 1 purification pack SIMPAK0R1
SimPak 2 purification pack SIMPAK0D2
SimFilter Final Filter SIMFILTER
Reservoir Vent Filter SIMVENT00
Spare Reservoir SIMTANK01
UV Lamp Simplicity SIM0000UV

Page 28/36

ORDERING INFORMATION ________________________________

Systems

Simplicity Water Purification System, 230 V 50 Hz SIMS50000

Simplicity Water Purification System, 115 V 60 Hz SIMS60000
 Page 29/36

________________________________ ORDERING INFORMATION

Millipore’s Standard Warranty _____________________________

Millipore Corporation (“Millipore”) warrants the products will meet their applicable published
specifications when used in accordance with the applicable instructions for a period of one year from
shipment of the products. MILLIPORE MAKES NO OTHER WARRANTY, EXPRESSED OR IMPLIED.
THERE IS NO WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

The warranty provided herein and the data, specifications and descriptions of Millipore products
appearing in Millipore’s published catalogues and product literature may not be altered except by
express written agreement signed by an officer of Millipore. Representations, oral or written, which
are inconsistent with this warranty or such publications are not authorized and if given, should not be
relied upon.

In the event of a breach of the foregoing warranty, Millipore’s sole obligation shall be to repair or
replace, at its option, the applicable product or part thereof, provided the customer notifies Millipore
promptly of any such breach. If after exercising reasonable efforts, Millipore is unable to repair or
replace the product or part, then Millipore shall refund to the customer all monies paid for such
applicable product or part. MILLIPORE SHALL NOT BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL,
SPECIAL OR ANY OTHER INDIRECT DAMAGES RESULTING FROM ECONOMIC LOSS OR
PROPERTY DAMAGE SUSTAINED BY ANY CUSTOMER FROM THE USE OF ITS PRODUCTS.

Page 29/36

________________________________ ORDERING INFORMATION

Millipore’s Standard Warranty _____________________________

Millipore Corporation (“Millipore”) warrants the products will meet their applicable published
specifications when used in accordance with the applicable instructions for a period of one year from
* Only present on Simplicity 185.

Page 30/36

ILLUSTRATIONS __________________________________________
Figure 1
The water flow schematic of the Simplicity is shown below. Only the main components are shown.

1 3

2 4
5

7
8

Reservoir 1
Pump 2
* UV Lamp 3
Pak 4
Resistivity cell 5
Point of use with dispensing valve 6
Check valve 7
Final filter 8
* Only present on Simplicity 185.

Page 30/36

ILLUSTRATIONS __________________________________________
Figure 1
The water flow schematic of the Simplicity is shown below. Only the main components are shown.

1 3
 Page 31/36

__________________________________________ ILLUSTRATIONS
Figure 2
A
B

MAN
UAL

MMILL
ILLIP
IPOORRE
E

D
C
E

Page 31/36

__________________________________________ ILLUSTRATIONS
Figure 2
A
B
 Page 32/36

ILLUSTRATIONS __________________________________________
Figure 3

B
D

Page 32/36

ILLUSTRATIONS __________________________________________
Figure 3
 Page 33/36

__________________________________________ ILLUSTRATIONS
Figure 4

E
A
B
C

Page 33/36

__________________________________________ ILLUSTRATIONS
Figure 4
 Page 34/36

ILLUSTRATIONS __________________________________________
Figure 5

Page 34/36

ILLUSTRATIONS __________________________________________
Figure 5
 Page 35/36

__________________________________________ ILLUSTRATIONS
Figure 6

Page 35/36

__________________________________________ ILLUSTRATIONS
Figure 6
Tel. (852) 2803-9111 Fax (06) 52.95.735
Fax +1 (781) 533-8630
Fax (852) 2513-0313

Page 36/36

To Place an Order or Receive Technical Assistance

For additional information call the nearest number listed below:
In the U.S. and Canada, call toll-free 1-800-MILLIPORE (1-800-645-5476)
In the U.S., Canada and Puerto Rico, fax orders toll-free 1-800-MILLIFX (1-800-645-5439)
On the Internet http://www.millipore.com
E-mail: tech_service@millipore.com

Millipore Worldwide Shanghai: JAPAN SPAIN AND PORTUGAL

Tel. (8621) 5306-9100 Tel. (03) 5442-9711 Madrid:
AUSTRALIA Fax (8621) 5306-0838 Fax (03) 5442- Tel. 917 283 960
Tel. 1 800 222 111 9736 Analytical Fax 917 292 909
or (02) 9888 8999 CZECH REPUBLIC 9737 BioProcess Barcelona:
Fax (02) 9878 0788 Tel. 02-205 138 41 9734 Lab Water Tel. 934 525 530
02-205 138 42 Fax 934 516 048
AUSTRIA, CENTRAL EUROPE, Fax 02-205 14294 KOREA
C.I.S., AFRICA, MIDDLE EAST Tel. (822) 551-0990 SWEDEN
AND GULF DENMARK Fax (822) 551-0228 Tel. 08-628 69 60
Tel. (43) 1 877-8926 Tel. 70 10 00 23 Fax 08-628 64 57
Fax (43) 1 877-1654 Fax 70 10 13 14 MALAYSIA
Tel. 603-757 1322 SWITZERLAND
BALTIC COUNTRIES FINLAND Fax 603-757 1711 Volketswil:
Tel. 358-9-804 5110 Tel. (09) 804 5110 Tel. (01) 908-30-60
Fax 358-9-256 5660 Fax (09) 256 5660 MEXICO Fax (01) 908-30-80
Tel. (525) 576-9688 Lausanne:
BELGIUM AND FRANCE Fax (525) 576-8706
LUXEMBOURG Tel. (01) 30.12.70.00 Tel. (021) 648 51 18
Tel. (02) 726 88 40 Fax (01) 30.12.71.80 THE NETHERLANDS Fax (021) 648 51 37
Fax (02) 726 98 84 Tel. 076-5022000 TAIWAN
GERMANY Fax 076-5022436
BRAZIL Tel. (06196) 494-0 Taipei:
Tel. (011) 548-7011 Fax (06196) 43901 NORWAY Tel. (886-2) 700-1742
Fax (011) 548-7923 Tel. 22 67 82 53 Fax (886-2) 755-3267
HUNGARY Fax 22 66 04 60 Hsin Chu City:
CANADA Tel. 1-205 9784 Tel. (886-3) 571-0178
Tel. 1-800-645-5476 Fax 1-205 9792 POLAND Fax (886-3) 572-9520
Fax 1-800-645-5439 Tel. 22-669 12 25
INDIA 22-663 70 31 U.K. AND IRELAND
CHINA, PEOPLE’S Tel. (91) 80-839 46 57 Fax 22-663 70 33 Tel. (01923) 816375
REPUBLIC OF Fax (91) 80-839 63 45 Fax (01923) 818297
Beijing: PUERTO RICO
Tel. (8610) 6500-8063 ITALY Tel. (787) 273-8495 U.S.A.
Fax (8610) 6500-7372 Vimodrone (Milano): Fax (787) 747-6553 Tel. (781) 533-6000
Guangzhou: Tel. (02) 25.07.81 Fax (781) 533-3110
Tel. (8620) 8755-4021 Fax (02) 26.50.324 SINGAPORE
Roma: Tel. (65) 842 1822 OTHER COUNTRIES
Fax (8620) 8755-4350 Millipore Intertech (U.S.A.)
Hong Kong: Tel. (06) 52.03.600 Fax (65) 842 4988
Fax (06) 52.95.735 Tel. +1 (781) 533-8622
Tel. (852) 2803-9111 Fax +1 (781) 533-8630
Fax (852) 2513-0313

Page 36/36

To Place an Order or Receive Technical Assistance

For additional information call the nearest number listed below:
In the U.S. and Canada, call toll-free 1-800-MILLIPORE (1-800-645-5476)
In the U.S., Canada and Puerto Rico, fax orders toll-free 1-800-MILLIFX (1-800-645-5439)
On the Internet http://www.millipore.com
Shanghai: