Gas Service

Handbook
Commercial/Industrial &
Multifamily Developments

MADISON GAS AND ELECTRIC CO. • MADISON, WISCONSIN

GS1315 09/27/2012
 Service - The pipe which carries gas from the Stub - The portion of the gas service from the
main to the customer’s meter. main to the property line.

Service shutoff valve - A convenient shutoff Therm - A therm of gas contains 100,000 Btu of
located outside of the customer’s building. If energy and is roughly equivalent to 100 cubic
the meter is located outside of the building, the feet of gas.
meter set assembly shutoff valve may also be the
service shutoff valve. In some commercial service
applications this buried valve may be located in Trench - An excavated ditch of specific depth and
the right-of-way at the customer’s property line. width into which underground utility lines are
installed.

© Copyright 2007, Madison Gas and Electric Co.

✓✓Fall 2012 Edition

29
 Table of Contents
Main (Gas) - The distribution line (or pipe) that Natural gas - A naturally occurring mixture of
serves as a common source of supply for more flammable hydrocarbon and nonhydrocarbon Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
than one service line. Owned and maintained by gases found in porous geologic formations What This Handbook Contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
MGE. beneath the earth’s surface often in association
with petroleum. It’s supplied as a fuel for millions MGE’s Service Territory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
of applications worldwide. The chemical composi- Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Manifold - Usually two or more natural gas meters tion is approximately 96 percent methane,
on one service line and regulator. 2 percent ethane, and 2 percent inert gases. Scheduling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Codes and Jurisdictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Mercaptan - An organic chemical odorant added Propane gas (C3H8 ) - A colorless flammable gas How to Contact MGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
to natural gas to give it a distinctive smell to alert found in petroleum and natural gas. It is odor- MGE’s Service Providers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
customers in case of leaks. Natural gas is odor- ized to make it easy to detect (smells sort of like
less in its natural state. Mercaptan smells some- garlic), heavier than air (specific gravity of 1.5),
thing like rotten eggs. and has a Btu of 2,544 per cubic foot, whereas Overview: Bringing Natural Gas to Your Building Site . . . . . . . . . . . . . . . . . . . . . . . . . . 4
natural gas contains about 1,000 Btu per cubic
foot.
Meter - A device for measuring and recording the Chapter 1: Steps to a Smooth Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
volume of gas used. The Basics: Understanding the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Rate - Method of charging for energy usage. In the
case of natural gas, for therms used. Getting Started With the Installation Process . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Meter set assembly shutoff valve - A positive Is There a Gas Main Located Near Your Site? . . . . . . . . . . . . . . . . . . . . . . . . . 5
shutoff valve on all metering and/or service regu-
lating facilities. The valve is located immediately Regulator (also Pressure regulator) - A device to What Natural Gas Equipment Will Be Installed in Your New Facility? . . . . . . . . . . . . 5
upstream (on the service line side) of the meter lower the gas pressure. District regulators lower Customer Fuel Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
set assembly. the pressure in mains. Meter regulators lower
pressure at the meter, and appliance regulators Underground Fuel Line Piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
• Open position - Valve handle is parallel with
the line (gas is flowing through the meter). lower pressure at the appliance. Factors That Can Delay Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

• Closed position - Valve is crosswise or at a Job Site Safety Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

right angle to the fuel line (gas is not flowing Right-of-way - A collection of easements and/ Locating Other Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
through the meter). or permits allowing the holder to specific limited
use of a parcel(s) of property (such as running a
gas main through private properties or a dedi- Chapter 2: Codes and Property Issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Methane gas (CH4 ) - A hydrocarbon gas that is cated area for use by the public for travel and Relevant Inspections and Local Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
the main component of natural gas (about 96 per- utilities). This term refers to the land itself, not
cent). It is colorless, odorless, and flammable and the right of passage over it. (See also Easement.) Easements and Public Right-of-Way Issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
the same substance produced in some swamps,
sewers, and landfills.
Riser - The portion of the service that terminates Chapter 3: Natural Gas Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
aboveground at the structure to support the Ordering Gas Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Multiple meter - Two or more meter sets branch- meter.
ing off separate risers. Bringing the Natural Gas Main to a New Commercial, Industrial, or Multifamily Facility . . . 9
Step 1: Application Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Riser valve - See meter set assembly shutoff
valve. Step 2: Design Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Step 3: Construction Scheduling Process . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

28 1
 Glossary
Chapter 4: Meter Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Selecting a Gas Meter Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Appliance shutoff valve - A valve readily acces- DOT (Department of Transportation) -
Required Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 sible and operable by the customer, located on U.S. Department of Transportation Office of
the fuel line at or very near the appliance. Pipeline Safety initiates and enforces regulations
Locations to Avoid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 relating to gas pipeline safety nationwide. Wis-
• Open position - Valve handle is parallel with
Minimum Meter Clearance Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 consin State Department of Transportation initi-
the line.
ates and enforces regulations relating to the use
Meter Set Assembly Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 • Closed position - Valve is crosswise or at a of public rights-of-way in the state.
Meter Installation and Turn-On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 right angle to the fuel line.
Guard Post and Curb Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Dry Utility - Power, phone, cable, or natural gas.
Backfill - Earth or other material used to refill a
trench. Also the act of refilling a trench.
Chapter 5: Pressure Gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Easement - A legal document entitling its holder
What is Pressure Gas? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 the right to use a specified parcel of property.
British thermal unit (Btu) - Quantity of heat nec- Easements give MGE the right to install under-
Requirements for Pressure Delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
essary to raise one pound of water one degree ground natural gas facilities on private property.
Upgrading Facilities to Accommodate Pressure Delivery . . . . . . . . . . . . . . . . . . . . 20 Fahreneheit at sea level pressure. The heating
quality of the gas. (One cubic foot of natural gas
contains about 1,000 Btu.) Emergency - A situation in which there is an
Appendices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 immediate threat to life or property. In the case of
Appendix A: MGE’s Natural Gas Service Territory Map . . . . . . . . . . . . . . . . . . . . . 22 natural gas, an emergency is an immediate threat
Carbon dioxide (CO2 ) - A gas which is a product and/or the uncontrolled escape of gas.
Appendix B: Natural Gas Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 of combustion, resulting when carbon unites with
What is Natural Gas? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 sufficient oxygen to produce complete combus-
tion. When natural gas burns completely, it Fuel line - Gas piping from the meter to the appli-
Things to Know About Natural Gas Safety . . . . . . . . . . . . . . . . . . . . . . . . . . 23 produces carbon dioxide and water vapor as well ance that is owned and maintained by the cus-
- Call Before You Dig! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 as heat. tomer.
- What to do if You Suspect a Natural Gas Leak . . . . . . . . . . . . . . . . . . . . . . 23
When and How to Shut Off Gas Service . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Carbon monoxide (CO) - A poisonous combustible Ignition temperature of natural gas - Natural gas
gas produced by the incomplete combustion of ignites at about 1,100 degrees Fahrenheit.
- When to Shut Off Your Gas Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
carbon or reduction of carbon dioxide.
- How to Shut Off Your Gas Service in an Emergency Situation . . . . . . . . . . . . . . 24
Ignitor - Any device used to light gas. A spark
- In a Nonemergency Situation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Combustion - The process of burning requiring ignitor uses an electric spark generated across an
- Gas Service Shutoff Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 three components: fuel, air, and ignition tem- air gap for this purpose.
What is Carbon Monoxide? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 perature.

- Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 • Complete combustion of natural gas results in Joint utility trench - Two or more utilities occupy-
carbon dioxide and water vapor; harmless. ing a common trench.
- Know the Early Symptoms of Carbon Monoxide Poisoning . . . . . . . . . . . . . . . . 25
• Incomplete combustion of natural gas can
produce carbon monoxide and aldehydes;
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 potentially hazardous. Load (Gas) - The connected load is calculated by
totaling the Btu rating for all gas appliances con-
nected to the meter.

2 27
Appendix C Preface
Codes and jurisdictions
Protection of Gas System from Back Pressure
or Vacuum What this handbook contains
This handbook shall not be interpreted to conflict
with the regulations of the State of Wisconsin
This handbook contains common information on or other regulatory bodies having jurisdiction.
A device shall be installed to protect MGE’s equip- Interconnection for Standby Fuels nonresidential service which includes:
ment/system should our customer’s equipment MGE’s requirements may be more stringent. Local
create a vacuum or back pressure (192.355)(a). • Commercial and industrial buildings codes and requirements related to the planned
Where a supplementary gas for standby use is
work should be addressed before any construc-
Natural gas compressors connected to MGE’s connected downstream from a meter or a service • Apartment complexes tion begins.
system shall be connected through a check valve regulator where a meter is not provided, equip-
• Multifamily structures
capable of withstanding the outlet pressure of the ment to prevent backflow shall be installed
compressor. (NFPA 5.3.2.1).
How to contact MGE
A three-way valve installed to admit the standby MGE’s service territory map
supply and at the same time shut off the regular
supply of natural gas shall be permitted to be Please direct any technical questions regarding
For your reference, the Territory Map in Appen- the information in this booklet to MGE’s Gas
used for this purpose (NFPA 5.3.2.2). dix A provides the general boundaries for MGE’s Engineering Department at (608) 252-7933 or
natural gas service. (608) 252-7931.
If you have any general billing questions
regarding your account, contact one of our cus-
Glossary of terms
tomer service representatives at (608) 252-7222
or 1-800-245-1125 from 7:00 a.m. to 7:00 p.m.
For your convenience, glossary terms appear in weekdays. You may also contact us by e-mail at
bold italics throughout the handbook the first mge@mge.com.
time they are referenced (e.g., meter).

MGE’s service providers

Scheduling
MGE contracts with a partner company, KS
The time needed for engineering, scheduling, Energy, to provide construction services. The
and construction of the work will vary depending project manager and employees who install your
upon the complexity of the job and the volume of service may work for these service providers on
work requested by MGE customers. Contact your MGE’s behalf.
operations scheduling representative at (608)
252-7373 for current construction scheduling.

26 3
Overview:
Bringing Natural Gas to Your Building Site
What is carbon monoxide? Know the early symptoms
of carbon monoxide poisoning
T his checklist notes the steps to bring natural gas to your
construction site. The information in this handbook
applies to MGE customers who require new nonresidential
plans (if new construction) and the legal
description or tax parcel identification. Carbon monoxide (CO) is an odorless, taste-
less, and invisible gas which can build up when If you think someone is suffering from carbon
natural gas service. If additional information is needed, • Call MGE after your fuel line has been any fuel-burning equipmentûan automobile,
contact a local MGE customer construction services repre- monoxide poisoning, move the person outside to
inspected and approved by your city or county fireplace, natural gas or oil furnace, wood stove,
sentative. fresh air immediately and seek medical help.
building department so MGE may unlock the propane heater, charcoal grill, or kerosene heater
valve, turn on the meter, and light your appli- has insufficient air to burn the fuel completely. Early symptoms include:
GAS ENGINEERING DEPART- ances (if necessary). Carbon monoxide exposure can be dangerous. • Dizziness
MENT ✓✓Removal of the lock or operation of the
• Flu-like symptoms
Commercial/Industrial and Multifamily shutoff valve may damage this equipment. Safety precautions
Customer Responsibilities: Only authorized MGE personnel can remove • Weakness
the lock and operate the valve. Here are suggestions to guard against carbon
monoxide exposure in any structure: • Nausea and vomiting
• Call MGE Gas Engineering Department to
• Use only fuel-burning equipment inside the • Partial loss of muscular control
determine if a natural gas main is located near
your building site.
MGE’s Responsibilities: structure that is designed to operate indoors. • Drowsiness
Vented gas equipment must vent to the out-
• Decide on your gas equipment and inform • Determine and inform you of gas availability. • Consider calling 9-1-1 if you have
side according to the manufacturer’s specifi-
MGE of its requirements. these symptoms
• Perform an economic feasibility study, if appli- cations.
✓✓MGE offers different delivery pressure cable. • Make sure fuel-burning equipment is main-
options that depend upon equipment load tained and operated safely and properly.
and equipment pressure requirements, • Notify you of:
which may result in special meter set and ✓✓Charges, if any. • Never run an automobile engine, lawn mower,
customer installation requirements. portable generator, or any combustion engine
✓✓Right-of-way or easement requirements. in an enclosed space.
• Complete and return the Gas Service Applica-
✓✓Additional permit requirements, if neces- • Keep flues and chimneys free of debris and
tion (provided by an MGE representative) via:
sary. clear of soot buildup.
✓✓The internet at https://www.mge.com/
• Install the natural gas main, service, and • Consider the installation of a carbon monox-
my_mge/serviceforms/installation/service-
meter set assembly. ide detector, particularly near sleeping areas
installation.asp
• Turn on and test your natural gas meter. in a structure.
✓✓Fax to MGE New Services at (608) 252-
5623, or
✓✓Mail to: Scheduling:
Madison Gas and Electric Co.
New Services • Scheduling will be based on a mutually
Post Office Box 1231 agreed-upon time frame that is consistent
Madison, Wisconsin 53701-1231 with your needs, permit requirements, and
• Provide MGE Gas Engineering Department design criteria.
with an approved, complete set of civil site

4 25
 Chapter 1
Steps to a Smooth Installation
When and how to shut off gas service In a nonemergency situation
The basics: understanding the installation What natural gas equipment
When an emergency strikes, it is not always nec- If you need gas service to be shut off for a tem- will be installed in your new facility?
essary to shut off your natural gas service. Know- porary, nonemergency situation, shut off service
at the fuel-line valve located near the particular Before MGE installs your natural gas facilities, it is
ing when and how to shut off natural gas service
appliance . important to understand the overall components Next, you will need to decide what natural gas
can save you from being without gas service
of an installation. You are responsible for your equipment will be installed so you can inform
needlessly.
natural gas fuel line and appliance hookup. MGE MGE of your estimated natural gas load. Evaluate
is responsible for the installation of the natural your total natural gas load by adding up the Btu
gas main, service, and meter (see Figure 1). inputs for all equipment being installed (immedi-
When to shut off your gas service ate and future), and tell us the desired pressure
delivery at the point of connection to the meter.
It is necessary to shut off your gas service at the Remember, besides space and water heat-
service shutoff valve at the meter only when you ing, natural gas can be used for air-conditioning,
hear or smell natural gas leaking. clothes drying, cooking, pool and spa heating,
barbecues, fireplaces, patio heaters, and genera-
tors. Be sure to consider all the options.
How to shut off your gas service
in an emergency situation
Customer fuel line
If there is an emergency situation and you need The fuel line is the gas piping (installed, owned,
to shut off gas service at your meter, follow these and maintained by the customer) that runs from
three steps: the meter to the customer’s equipment. There are
three types of fuel lines you can use:
Step Action Figure 1. Example of typical gas system components.
1. Locate the service shutoff valve (usually the first
fitting) on the natural gas supply pipe coming Getting started with 1. Rigid steel piping. Typically, threaded, rigid
out of the ground near the meter. the installation process steel pipe is used for natural gas piping. This
type of pipe has been used in the gas industry
Before the installation process can begin, you for a long time and is a reliable alternative for
2. Use a long-handled wrench to turn the valve need to know the following: house piping.
one-quarter turn so the lever is crosswise to the
pipe.
2. Flexible corrugated stainless steel tubing
Is there a gas main located near your site? (may require two-pound pressure delivery).
This is a new alternative that is gaining
To determine if a natural gas main is located near
3. Once the gas is off, leave it off. Call MGE to popularity because of ease of installation.
your building site, call MGE Gas Engineering at
inspect the system, check, and relight appli- Although flexible, corrugated stainless steel
(608) 252-7933 or (608) 252-7931.
ances. tubing (CSST) and fitting material is more
If there is no gas main located near your build- expensive to purchase than rigid steel pipe.
ing site, MGE will need to review and estimate
the feasibility of extending gas facilities to you. If
MGE determines that extending a gas main to you
is needed, main extension charges may apply.

Figure 11. Gas service shutoff valve

24 5
 Appendix B
Natural Gas Safety
3. Flexible copper tubing (may require two- If you smell the rotten egg smell of odorized
pound pressure delivery). Since its code natural gas, call MGE any time, 24 hours a day, at What is natural gas? What to do if you suspect
approval, flexible copper tubing (Type K or L (608) 252-1111 or 1-800-245-1123 and we will a natural gas leak
copper with 1,000° silver-soldered joints) has check it for you. For emergencies, call 9-1-1. Natural gas is 96 percent methane, a natural
received positive feedback from contractors. Caution: When excavating near buried gas piping, compound formed as plants, trees, and other The odorant added to the gas will enable you
Copper tubing is another good alternative for locate the piping first and excavate by hand. organic matter break down. While natural gas is to detect a small gas leak; however, using your
natural gas house piping that is flexible and combustible, it ignites only within a narrow range nose is not the only way to detect a leak. Bubbles
reliable. between 4 and 14 percent gas-in-air mixture. In blowing in a puddle or a hissing sound also may
smaller or greater concentrations, it will not burn. indicate a natural gas leak. If you suspect a natu-
NOTE: The International Fuel Gas Code regulates the For this reason, natural gas is a more stable fuel ral gas leak, follow these steps to ensure your
design and installation of fuel lines and appliances. The source than propane or gasoline. The exhaust safety and the safety of those around you:
International Fuel Gas Code also contains charts to cor- Factors that can delay installation from a properly working natural gas appliance is
rectly size your fuel line. Use this book as a reference when
designing your gas lines. It will be your responsibility to No one wants to have their project delayed. essentially carbon dioxide and water vaporûthe
• Leave the building immediately and leave the
ensure that a mechanical permit or a gas piping permit is We have identified the following circum- same substances released when we exhale.
obtained from your city or county building department and
door open on the way out.
that the building department performs an inspection of the
stances as common impediments to installing Natural gas is colorless and has no smell in
service lines: ✓✓Do not use a telephone inside the affected
completed installation. its natural state. A harmless odorant, mercaptan ,
building or do anything that might cause a
is added to create a distinct scent, so it is easy to
• Debris in the work area or along the route spark.
detect even the smallest natural gas leak. In addi-
Underground fuel line piping of the proposed service extension. tion, natural gas is 40 percent lighter than air. ✓✓Do not light a match.
Fuel gas piping between your gas meter and your • Building is not framed and sided at the Unlike propane, which will tend to pool close to ✓✓Do not turn on a light switch.
natural gas appliances or equipment, in most meter location for the meter set assembly the ground, if natural gas escapes, it will rise and
cases, will belong to you. If any of this piping runs dissipate safely into the atmosphere. ✓✓Do not attempt to put out flames if a gas
installation.
underground, such as to serve a hot tub, pool, leak ignites.
shop, other building or for a natural gas fueled • Requested meter location is not usable
• Use a neighbor’s phone or find a pay phone
standby generator, it needs to be maintained. or fails to meet minimum clearances (see Things to know about natural gas safety and call MGE at (608) 252-1111. (If you must
It is your responsibility to maintain this piping. Chapter 4, Selecting a gas meter location).
use your cellular phone, be sure you are well
If your buried piping is not maintained, it may • The foundation is not sufficiently back- When using any energy source, it is wise to be away from the building.)
leak or corrode. Be sure to periodically inspect filled to support the meter or service aware of and follow certain precautions to keep
• For emergencies, call 9-1-1.
buried pipes for leaks, and if the piping is metal- piping. yourself and those around you safe. Here are
lic, inspect for corrosion. Make sure repairs are some of the things you should know to safely
• Alterations that must be made to meet
done immediately to correct any unsafe condi- obtain gas service and use it safely once it has
local codes are not completed.
tion. A corrosion control company or a plumbing been established in your structure.
or heating contractor can help inspect and repair • In some cases, MGE will require a con-
it. crete pad to support the gas meter.
Call before you dig!
If you plan to excavate near your buried
piping, it should be located in advance and the
Be sure to call to have all underground utilities
excavation should be done by hand. A locating
located any time you plan to dig on your property.
service can help locate the piping if you are not
sure of its location. For free locating of utility- Call Diggers Hotline at 1-800-242-8511 to
owned lines (typically from the street to your have all underground utilities on your property
meter), call Diggers Hotline three business days identified at least three working days before you
in advance at 1-800-242-8511. dig.
NOTE: This is required even if you think you know there are
no other utilities where you intend to dig.

6 23
Appendix A
MGE’s Natural Gas Service Territory Map
Job site safety requirements Locating other utilities

In case of emergency involving a service line or State law requires that anyone planning to dig
main break, call our Customer Service Center at must notify Diggers Hotline three working days
1-800-252-1111 and 9-1-1. before you dig: 1-800-242-8511.
MGE asks that customers follow these safety The locator uses the following color codes to
requirements: identify underground utilities:
• Buildings should be framed and sided at the
meter location before we can set a gas meter. Color Utility
MGE may not install meter set assemblies Yellow Gas, oil, steam, petroleum, or gaseous
against foundations only. materials
Red Electric power lines, cables, conduit,
• A meter may be installed, but gas will not be
and lighting cables
turned on until your fuel line has been pres-
sure tested and an approved permit has been Orange Communication, alarm, or signal lines; cables,
obtained from and signed off by the local conduit, cable TV
administrative authority. Blue Water, irrigation, and slurry lines
Green Sewers and drain lines
• Our crew will ask you to extinguish any smok-
White Proposed excavation
ing material or open flame that presents a
Pink Temporary survey markings
danger to the operation prior to a line purge.

Figure 10. Natural gas service territory within and

contiguous to Dane County

22 7
Chapter 2 Appendices
Codes and Property Issues
Appendix A

Relevant inspections and local codes Easements and public right-of-way issues • MGE’s Natural Gas Service Territory Map

This handbook provides most of the informa- As part of the installation process, MGE will:
tion and requirements needed to bring natural Appendix B
• Apply for any necessary easements prior to
gas to your building site. However, it does not
installation using the customer’s information.
include all possible standards and specifica- • Natural Gas Safety
tions required by MGE or state, federal, or local • Apply for all necessary permits for the portion
code. If you need additional information, contact of the work done in the public right-of-way.
your MGE representative, your local government • Request Diggers Hotline utility locations.
agency, or state authority.
• Dig trench to install all necessary gas facili-
This handbook shall not be interpreted to con- ties.
flict with the regulations of the State of Wisconsin
or other regulatory bodies having jurisdiction. • Backfill and be responsible for the trench dug
MGE’s requirements may be more stringent. Local to install gas facilities.
codes and requirements related to the planned • If MGE is digging the trench on private prop-
work should be addressed before any construc- erty, MGE will provide and install the bedding
tion begins. material to protect the pipe.

8 21
Chapter 5 Chapter 3
Pressure Gas Natural Gas Installation
What is ‘pressure gas?’ Upgrading facilities
to accommodate pressure delivery
The standard delivery pressure for MGE is Ordering gas service Bringing the natural gas main
8 inches of water column (w.c.), which is approxi- Occasionally, existing MGE gas facilities (such as to a new commercial, industrial,
mately one-quarter pound per square inch (psi). mains, services, or meter set assemblies) are not To order individual service lines, call our New Ser- or multifamily facility
This is the lowest delivery pressure provided by adequate to meet the new or additional pressure vice Installation Department at (608) 252-7373 or
MGE. Anything higher than 8-inch w.c. is consid- delivery requirements of multifamily, commercial, complete a Gas and Electric Service Application
Step 1: Application process
ered “pressure gas” or “pressure delivery.” or industrial customers. Existing customer-owned with the following information:
fuel line and other equipment may also be under- Please complete and sign the Application for
In addition, 8-inch w.c., the most common Service and provide MGE with an original scaled
sized if load is being added. • Service address, including suite number
pressures used by multifamily, commercial, and copy of the approved site plan(s) drawings and,
industrial customers, are 2 psi and 5 psi. (Higher There are various solutions to this problem. • Engineering site plan with corresponding if available, a disk with the electronic files of the
pressures are also available by special request MGE may choose to: meter location plans in a .dgn or .dwg file format. Include lot
based on application.) • Increase the size or pressure of the gas mains. lines and driveways and omit extraneous informa-
• Pressure required at meter connection point
NOTE: Pressures other than those listed above require tion.
special review and approval by MGE. • Increase the size of the service piping. • Loads for each individual meter
• Increase the metering capacity of the existing Step 2: Design process
If you desire pressure delivery, discuss the • Contact name and mailing address
requirements with your customer service repre- meter set assembly. MGE creates the design for gas main, gas service,
sentative. and metering to serve your facility and applies for
At times, the costs to make these changes appropriate easements and permits. This process
are the customer’s responsibility. At other times, averages four to six weeks.
Requirements for pressure delivery the responsibility for these costs is that of MGE. Step 3: Construction scheduling process
Please contact MGE to make this determination. When ready, please call a construction schedul-
For your safety and to maintain system integrity, ing representative to discuss your anticipated
the following basic requirements must be met construction schedule.
before MGE can provide you with pressure deliv-
ery:
• MGE must be assured that providing such
service is not detrimental to the Company or
its other customers.
• Your use of such service is or will be in accor-
dance with MGE’s rates, tariffs, and stan-
dards.

20 9
Typical Gas Main Trench

Meter installation and turn on • See Figure 9 for guard post spacing require-
ments. Maximum spacing is required to pro-
tect meter set assembly and service riser from
Figures 4 and 5 (see pages 14 and 15) show a
damage.
typical small-load gas meter installation after the
meter has been turned on. • Do not install a guard post in line with or to
the sides of the gas meter in order to ensure
When MGE installs the gas meter, the follow-
proper access for maintenance.
ing components will be installed.
Before the gas meter can be turned on, the
fuel line shall be inspected and approved (permit In cases where the meter will be installed behind
signed and approved by the local administrative a curb, observe the following:
authority).
The customers’ gas piping shall be connected • If there is less than 5 feet between the curb
to the meter and at least one piece of utiliza- and the meter, guard posts shall be installed
tion equipment. MGE will not set the meter if per Figure 9.
the appliances are not vented correctly. Also, to • Other guard post designs will be considered.
assist in establising your service, the unit number Please contact MGE Gas Systems Engineer-
being served by a particular meter needs to be ing at (608) 252-7933 or (608) 252-7931 to
marked on the meter bar as well as the doorway. discuss those options.
To arrange for the gas meter turn on, please
call MGE at (608) 252-7222. Call by 3:00 p.m. for
same-day gas meter turn on for up to two meters.
For facilities with more than two meters, call MGE
to schedule meter turn on.
NOTE: This applies on regular business days, subject to
delays associated with major storms, supply interruptions,
or other adverse events beyond MGE’s control.
Figure 2. Typical commercial gas main line trench.

Guard post and curb requirements

For commercial/industrial and multifamily

meters, guard posts shall be, at a minimum:
• 4-inch diameter steel pipe, 6-foot long, filled Figure 9. Commercial/industrial and multifamily meter
with wet concrete. guard post requirements.

• Each guard post shall be embedded in a mini-

mum of a 15-inch diameter by 30-inch high
concrete base with at least 24 inches of the
guard post encased in the base.

10 19
Typical Apartment Meter Bank (Four High) Typical Gas Service Line

Figure 8. This is a typical inside meter rack where the floor-to-ceiling

height is 8 feet or more. MGE would install the rack on an outside
wall with meter rows going three high and extending out to accom-
modate the number of meters desired. This rack will either extend
from the wall penetration and go left to right or right to left depend-
ing on available space. The dimensions are relatively accurate, but
verification of room needs to be done by MGE’s Gas Engineering
Department. MGE would prefer the gas regulating equipment to be
outside, but if circumstances dictate it being inside, we will con-
sider installing it with the meter set. The wall to the front face of the
meter will be approximately 18 inches. MGE requires the contractor
to install meter protection posts and brackets to protect the rack/
meters from damage. All designs of this and clearances will be veri-
fied by the Gas Engineering Department. MGE also requires the
contractor to core holes in the wall of the building so associated gas Figure 3. Typical commercial/industrial/multifamily joint
pipes can be installed in the basement and vent lines can exit. Exact utility service trench with customer-installed gas service
size and placement will be agreed on at the time of installation. This conduit.
drawing is to be used as a general reference by engineers, architects,
and designers. Loads and meters vary, so actual gas meter racks will
likewise vary. Actual design can be verified with the Gas Engineer-
ing Department along with questions as to design and placement.
18 11
Chapter 4 Typical Apartment Meter Bank (Three High)
Meter Installation
Before MGE can start the natural gas meter instal- Locations to avoid
lation, you must mark the gas meter location on
engineering plans for design of your meter set. The following meter locations present access
problems or could expose the meter to accidental
damage. We require you avoid the following loca-
Selecting a gas meter location tions:

Safe installation and operation of your gas

service equipment is MGE’s primary concern. An • Public passageways or fire escape routes.
approved natural gas meter location is one that • Under a stairway or walkway.
is in accordance with regulatory requirements
• On building rooftops.
and meets MGE’s construction standards. A good
meter location is one where the meter is: • Unventilated, confined, or inaccessible
places.
• Easy to read and inspect. • Under openable windows (because of regula-
tor relief).
• Accessible for turn on, shut off, maintenance,
change, or removal. • Directly adjacent to vehicular driveways,
delivery doors, or high traffic areas where the
• Protected against electric sparks, exces-
meter may be subjected to vehicular damage.
sive temperatures, flames, and mechanical
(Guard posts may be required if such locations
damage.
are unavoidable. See Guard post and curb
• Adequately ventilated. requirements section.) Figure 7. This is a typical inside meter rack where the floor-
• Protected against vehicular damage. • Near electrical transformers or control rooms. to-ceiling height is less than 8 feet. MGE would install the
rack on an outside wall with meter rows going three high
• Within 3 feet of sources of ignition (such as and extending out to accommodate the number of meters
Required location furnaces, water heaters, switch boxes, fuse desired. This rack will either extend from the wall pen-
boxes, breaker panels, or electrical outlets etration and go left to right or right to left depending on
where arcing can occur). available space. The dimensions are relatively accurate, but
MGE encourages you to locate the meter outside, verification of room needs to be done by MGE’s Gas Engi-
alongside the building, and close to the source of • Within 10 feet of any air intake. neering Department. MGE would prefer the gas regulating
gas supply. equipment to be outside, but if circumstances dictate it
being inside, we will consider installing it with the meter
NOTE: Talk to your local MGE gas engineer for protection set. The wall to the front face of the meter will be approxi-
NOTE: Inside meter locations are used only with MGE’s that may be required for your meter from flooding, snow, or mately 18 inches. MGE requires the contractor to install
approval. ice. meter protection posts and brackets to protect the rack/
meters from damage. All designs of this and clearances
will be verified by the Gas Engineering Department. MGE
also requires the contractor to core holes in the wall of the
building so associated gas pipes can be installed in the base-
ment and vent lines can exit. Exact size and placement will
be agreed on at the time of installation. This drawing is to
be used as a general reference by engineers, architects, and
designers. Loads and meters vary, so actual gas meter racks
will likewise vary. Actual design can be verified with the Gas
Engineering Department along with questions as to design
and placement.

12 17
Typical Large Commercial Gas Meter
Minimum meter clearance requirements Meter set assembly selection

Minimum clearances are measured from the relief To begin the meter set selection process, fill out
vent on the gas meter set assembly or the relief the Application for Gas and Electric Service pro-
valve stack (Figures 4 and 5). vided by the MGE representative. The information
on the worksheet helps the MGE representative
The relief vent or stack exhausts natural
determine the maximum and minimum load and
gas safely into the atmosphere in the event the
delivery pressure of the natural gas service.
regulator on the meter fails to work properly. The
diagrams and measurements provided show the Meter set assembly selection is determined
required minimum distances between building by the customer’s immediate needs. This opti-
features and the relief vent. mizes meter accuracy and minimizes installation
costs.
However, if a customer plans to add load in
the near future and if the meter set assembly
sized for the future load will adequately measure
the present load, MGE will specify a meter set
assembly based on the future load.
The most common meter set assemblies are
the diaphragm and rotary (Figures 4, 5, and 6). If
your commercial structure has multiple tenants,
you may require a manifold meter set (Figures 7
and 8).
Your individual installation may be different.
Figure 6. This is a typical outside meter rack. This installation
could be put inside the building, but the meter location needs
verification by MGE’s Gas Engineering Department. This rack
will extend on an outside wall from left to right or right to left
depending on available space. MGE would prefer the gas regu-
lating equipment to be outside, but if circumstances dictate it
being inside, we will consider installing it with the meter set.
The wall to the front face of the meter is approximately
3 feet. MGE requires the contractor to install meter protection
posts and brackets to protect the rack/meter from damage.
All designs of this and clearances will be verified by the Gas
Engineering Department. MGE also requires the contractor
to core holes in the wall of the building so associated gas pipes
can be installed in the basement and vent lines can exit. Exact
size and placement will be agreed on at the time of installation.
This drawing is to be used as a general reference by engineers,
architects, and designers. Loads and meters vary, so actual gas
meter racks will likewise vary. Actual design can be verified
with the Gas Engineering Department along with questions as
to design and placement.

16 13
Typical Gas Meter for Small Loads Typical Small Commercial Gas Meter

Figure 4. Typical 250 gas meter set assembly for small loads.

Figure 5. Typical 425 through 1000 gas meter set assembly.

14 15
Typical Gas Meter for Small Loads Typical Small Commercial Gas Meter

Figure 4. Typical 250 gas meter set assembly for small loads.

Figure 5. Typical 425 through 1000 gas meter set assembly.

14 15
Typical Large Commercial Gas Meter
Minimum meter clearance requirements Meter set assembly selection

Minimum clearances are measured from the relief To begin the meter set selection process, fill out
vent on the gas meter set assembly or the relief the Application for Gas and Electric Service pro-
valve stack (Figures 4 and 5). vided by the MGE representative. The information
on the worksheet helps the MGE representative
The relief vent or stack exhausts natural
determine the maximum and minimum load and
gas safely into the atmosphere in the event the
delivery pressure of the natural gas service.
regulator on the meter fails to work properly. The
diagrams and measurements provided show the Meter set assembly selection is determined
required minimum distances between building by the customer’s immediate needs. This opti-
features and the relief vent. mizes meter accuracy and minimizes installation
costs.
However, if a customer plans to add load in
the near future and if the meter set assembly
sized for the future load will adequately measure
the present load, MGE will specify a meter set
assembly based on the future load.
The most common meter set assemblies are
the diaphragm and rotary (Figures 4, 5, and 6). If
your commercial structure has multiple tenants,
you may require a manifold meter set (Figures 7
and 8).
Your individual installation may be different.
Figure 6. This is a typical outside meter rack. This installation
could be put inside the building, but the meter location needs
verification by MGE’s Gas Engineering Department. This rack
will extend on an outside wall from left to right or right to left
depending on available space. MGE would prefer the gas regu-
lating equipment to be outside, but if circumstances dictate it
being inside, we will consider installing it with the meter set.
The wall to the front face of the meter is approximately
3 feet. MGE requires the contractor to install meter protection
posts and brackets to protect the rack/meter from damage.
All designs of this and clearances will be verified by the Gas
Engineering Department. MGE also requires the contractor
to core holes in the wall of the building so associated gas pipes
can be installed in the basement and vent lines can exit. Exact
size and placement will be agreed on at the time of installation.
This drawing is to be used as a general reference by engineers,
architects, and designers. Loads and meters vary, so actual gas
meter racks will likewise vary. Actual design can be verified
with the Gas Engineering Department along with questions as
to design and placement.

16 13
Chapter 4 Typical Apartment Meter Bank (Three High)
Meter Installation
Before MGE can start the natural gas meter instal- Locations to avoid
lation, you must mark the gas meter location on
engineering plans for design of your meter set. The following meter locations present access
problems or could expose the meter to accidental
damage. We require you avoid the following loca-
Selecting a gas meter location tions:

Safe installation and operation of your gas

service equipment is MGE’s primary concern. An • Public passageways or fire escape routes.
approved natural gas meter location is one that • Under a stairway or walkway.
is in accordance with regulatory requirements
• On building rooftops.
and meets MGE’s construction standards. A good
meter location is one where the meter is: • Unventilated, confined, or inaccessible
places.
• Easy to read and inspect. • Under openable windows (because of regula-
tor relief).
• Accessible for turn on, shut off, maintenance,
change, or removal. • Directly adjacent to vehicular driveways,
delivery doors, or high traffic areas where the
• Protected against electric sparks, exces-
meter may be subjected to vehicular damage.
sive temperatures, flames, and mechanical
(Guard posts may be required if such locations
damage.
are unavoidable. See Guard post and curb
• Adequately ventilated. requirements section.) Figure 7. This is a typical inside meter rack where the floor-
• Protected against vehicular damage. • Near electrical transformers or control rooms. to-ceiling height is less than 8 feet. MGE would install the
rack on an outside wall with meter rows going three high
• Within 3 feet of sources of ignition (such as and extending out to accommodate the number of meters
Required location furnaces, water heaters, switch boxes, fuse desired. This rack will either extend from the wall pen-
boxes, breaker panels, or electrical outlets etration and go left to right or right to left depending on
where arcing can occur). available space. The dimensions are relatively accurate, but
MGE encourages you to locate the meter outside, verification of room needs to be done by MGE’s Gas Engi-
alongside the building, and close to the source of • Within 10 feet of any air intake. neering Department. MGE would prefer the gas regulating
gas supply. equipment to be outside, but if circumstances dictate it
being inside, we will consider installing it with the meter
NOTE: Talk to your local MGE gas engineer for protection set. The wall to the front face of the meter will be approxi-
NOTE: Inside meter locations are used only with MGE’s that may be required for your meter from flooding, snow, or mately 18 inches. MGE requires the contractor to install
approval. ice. meter protection posts and brackets to protect the rack/
meters from damage. All designs of this and clearances
will be verified by the Gas Engineering Department. MGE
also requires the contractor to core holes in the wall of the
building so associated gas pipes can be installed in the base-
ment and vent lines can exit. Exact size and placement will
be agreed on at the time of installation. This drawing is to
be used as a general reference by engineers, architects, and
designers. Loads and meters vary, so actual gas meter racks
will likewise vary. Actual design can be verified with the Gas
Engineering Department along with questions as to design
and placement.

12 17
Typical Apartment Meter Bank (Four High) Typical Gas Service Line

Figure 8. This is a typical inside meter rack where the floor-to-ceiling

height is 8 feet or more. MGE would install the rack on an outside
wall with meter rows going three high and extending out to accom-
modate the number of meters desired. This rack will either extend
from the wall penetration and go left to right or right to left depend-
ing on available space. The dimensions are relatively accurate, but
verification of room needs to be done by MGE’s Gas Engineering
Department. MGE would prefer the gas regulating equipment to be
outside, but if circumstances dictate it being inside, we will con-
sider installing it with the meter set. The wall to the front face of the
meter will be approximately 18 inches. MGE requires the contractor
to install meter protection posts and brackets to protect the rack/
meters from damage. All designs of this and clearances will be veri-
fied by the Gas Engineering Department. MGE also requires the
contractor to core holes in the wall of the building so associated gas Figure 3. Typical commercial/industrial/multifamily joint
pipes can be installed in the basement and vent lines can exit. Exact utility service trench with customer-installed gas service
size and placement will be agreed on at the time of installation. This conduit.
drawing is to be used as a general reference by engineers, architects,
and designers. Loads and meters vary, so actual gas meter racks will
likewise vary. Actual design can be verified with the Gas Engineer-
ing Department along with questions as to design and placement.
18 11
Typical Gas Main Trench

Meter installation and turn on • See Figure 9 for guard post spacing require-
ments. Maximum spacing is required to pro-
tect meter set assembly and service riser from
Figures 4 and 5 (see pages 14 and 15) show a
damage.
typical small-load gas meter installation after the
meter has been turned on. • Do not install a guard post in line with or to
the sides of the gas meter in order to ensure
When MGE installs the gas meter, the follow-
proper access for maintenance.
ing components will be installed.
Before the gas meter can be turned on, the
fuel line shall be inspected and approved (permit In cases where the meter will be installed behind
signed and approved by the local administrative a curb, observe the following:
authority).
The customers’ gas piping shall be connected • If there is less than 5 feet between the curb
to the meter and at least one piece of utiliza- and the meter, guard posts shall be installed
tion equipment. MGE will not set the meter if per Figure 9.
the appliances are not vented correctly. Also, to • Other guard post designs will be considered.
assist in establising your service, the unit number Please contact MGE Gas Systems Engineer-
being served by a particular meter needs to be ing at (608) 252-7933 or (608) 252-7931 to
marked on the meter bar as well as the doorway. discuss those options.
To arrange for the gas meter turn on, please
call MGE at (608) 252-7222. Call by 3:00 p.m. for
same-day gas meter turn on for up to two meters.
For facilities with more than two meters, call MGE
to schedule meter turn on.
NOTE: This applies on regular business days, subject to
delays associated with major storms, supply interruptions,
or other adverse events beyond MGE’s control.
Figure 2. Typical commercial gas main line trench.

Guard post and curb requirements

For commercial/industrial and multifamily

meters, guard posts shall be, at a minimum:
• 4-inch diameter steel pipe, 6-foot long, filled Figure 9. Commercial/industrial and multifamily meter
with wet concrete. guard post requirements.

• Each guard post shall be embedded in a mini-

mum of a 15-inch diameter by 30-inch high
concrete base with at least 24 inches of the
guard post encased in the base.

10 19
Chapter 5 Chapter 3
Pressure Gas Natural Gas Installation
What is ‘pressure gas?’ Upgrading facilities
to accommodate pressure delivery
The standard delivery pressure for MGE is Ordering gas service Bringing the natural gas main
8 inches of water column (w.c.), which is approxi- Occasionally, existing MGE gas facilities (such as to a new commercial, industrial,
mately one-quarter pound per square inch (psi). mains, services, or meter set assemblies) are not To order individual service lines, call our New Ser- or multifamily facility
This is the lowest delivery pressure provided by adequate to meet the new or additional pressure vice Installation Department at (608) 252-7373 or
MGE. Anything higher than 8-inch w.c. is consid- delivery requirements of multifamily, commercial, complete a Gas and Electric Service Application
Step 1: Application process
ered “pressure gas” or “pressure delivery.” or industrial customers. Existing customer-owned with the following information:
fuel line and other equipment may also be under- Please complete and sign the Application for
In addition, 8-inch w.c., the most common Service and provide MGE with an original scaled
sized if load is being added. • Service address, including suite number
pressures used by multifamily, commercial, and copy of the approved site plan(s) drawings and,
industrial customers, are 2 psi and 5 psi. (Higher There are various solutions to this problem. • Engineering site plan with corresponding if available, a disk with the electronic files of the
pressures are also available by special request MGE may choose to: meter location plans in a .dgn or .dwg file format. Include lot
based on application.) • Increase the size or pressure of the gas mains. lines and driveways and omit extraneous informa-
• Pressure required at meter connection point
NOTE: Pressures other than those listed above require tion.
special review and approval by MGE. • Increase the size of the service piping. • Loads for each individual meter
• Increase the metering capacity of the existing Step 2: Design process
If you desire pressure delivery, discuss the • Contact name and mailing address
requirements with your customer service repre- meter set assembly. MGE creates the design for gas main, gas service,
sentative. and metering to serve your facility and applies for
At times, the costs to make these changes appropriate easements and permits. This process
are the customer’s responsibility. At other times, averages four to six weeks.
Requirements for pressure delivery the responsibility for these costs is that of MGE. Step 3: Construction scheduling process
Please contact MGE to make this determination. When ready, please call a construction schedul-
For your safety and to maintain system integrity, ing representative to discuss your anticipated
the following basic requirements must be met construction schedule.
before MGE can provide you with pressure deliv-
ery:
• MGE must be assured that providing such
service is not detrimental to the Company or
its other customers.
• Your use of such service is or will be in accor-
dance with MGE’s rates, tariffs, and stan-
dards.

20 9
Chapter 2 Appendices
Codes and Property Issues
Appendix A

Relevant inspections and local codes Easements and public right-of-way issues • MGE’s Natural Gas Service Territory Map

This handbook provides most of the informa- As part of the installation process, MGE will:
tion and requirements needed to bring natural Appendix B
• Apply for any necessary easements prior to
gas to your building site. However, it does not
installation using the customer’s information.
include all possible standards and specifica- • Natural Gas Safety
tions required by MGE or state, federal, or local • Apply for all necessary permits for the portion
code. If you need additional information, contact of the work done in the public right-of-way.
your MGE representative, your local government • Request Diggers Hotline utility locations.
agency, or state authority.
• Dig trench to install all necessary gas facili-
This handbook shall not be interpreted to con- ties.
flict with the regulations of the State of Wisconsin
or other regulatory bodies having jurisdiction. • Backfill and be responsible for the trench dug
MGE’s requirements may be more stringent. Local to install gas facilities.
codes and requirements related to the planned • If MGE is digging the trench on private prop-
work should be addressed before any construc- erty, MGE will provide and install the bedding
tion begins. material to protect the pipe.

8 21
Appendix A
MGE’s Natural Gas Service Territory Map
Job site safety requirements Locating other utilities

In case of emergency involving a service line or State law requires that anyone planning to dig
main break, call our Customer Service Center at must notify Diggers Hotline three working days
1-800-252-1111 and 9-1-1. before you dig: 1-800-242-8511.
MGE asks that customers follow these safety The locator uses the following color codes to
requirements: identify underground utilities:
• Buildings should be framed and sided at the
meter location before we can set a gas meter. Color Utility
MGE may not install meter set assemblies Yellow Gas, oil, steam, petroleum, or gaseous
against foundations only. materials
Red Electric power lines, cables, conduit,
• A meter may be installed, but gas will not be
and lighting cables
turned on until your fuel line has been pres-
sure tested and an approved permit has been Orange Communication, alarm, or signal lines; cables,
obtained from and signed off by the local conduit, cable TV
administrative authority. Blue Water, irrigation, and slurry lines
Green Sewers and drain lines
• Our crew will ask you to extinguish any smok-
White Proposed excavation
ing material or open flame that presents a
Pink Temporary survey markings
danger to the operation prior to a line purge.

Figure 10. Natural gas service territory within and

contiguous to Dane County

22 7
 Appendix B
Natural Gas Safety
3. Flexible copper tubing (may require two- If you smell the rotten egg smell of odorized
pound pressure delivery). Since its code natural gas, call MGE any time, 24 hours a day, at What is natural gas? What to do if you suspect
approval, flexible copper tubing (Type K or L (608) 252-1111 or 1-800-245-1123 and we will a natural gas leak
copper with 1,000° silver-soldered joints) has check it for you. For emergencies, call 9-1-1. Natural gas is 96 percent methane, a natural
received positive feedback from contractors. Caution: When excavating near buried gas piping, compound formed as plants, trees, and other The odorant added to the gas will enable you
Copper tubing is another good alternative for locate the piping first and excavate by hand. organic matter break down. While natural gas is to detect a small gas leak; however, using your
natural gas house piping that is flexible and combustible, it ignites only within a narrow range nose is not the only way to detect a leak. Bubbles
reliable. between 4 and 14 percent gas-in-air mixture. In blowing in a puddle or a hissing sound also may
smaller or greater concentrations, it will not burn. indicate a natural gas leak. If you suspect a natu-
NOTE: The International Fuel Gas Code regulates the For this reason, natural gas is a more stable fuel ral gas leak, follow these steps to ensure your
design and installation of fuel lines and appliances. The source than propane or gasoline. The exhaust safety and the safety of those around you:
International Fuel Gas Code also contains charts to cor- Factors that can delay installation from a properly working natural gas appliance is
rectly size your fuel line. Use this book as a reference when
designing your gas lines. It will be your responsibility to No one wants to have their project delayed. essentially carbon dioxide and water vaporûthe
• Leave the building immediately and leave the
ensure that a mechanical permit or a gas piping permit is We have identified the following circum- same substances released when we exhale.
obtained from your city or county building department and
door open on the way out.
that the building department performs an inspection of the
stances as common impediments to installing Natural gas is colorless and has no smell in
service lines: ✓✓Do not use a telephone inside the affected
completed installation. its natural state. A harmless odorant, mercaptan ,
building or do anything that might cause a
is added to create a distinct scent, so it is easy to
• Debris in the work area or along the route spark.
detect even the smallest natural gas leak. In addi-
Underground fuel line piping of the proposed service extension. tion, natural gas is 40 percent lighter than air. ✓✓Do not light a match.
Fuel gas piping between your gas meter and your • Building is not framed and sided at the Unlike propane, which will tend to pool close to ✓✓Do not turn on a light switch.
natural gas appliances or equipment, in most meter location for the meter set assembly the ground, if natural gas escapes, it will rise and
cases, will belong to you. If any of this piping runs dissipate safely into the atmosphere. ✓✓Do not attempt to put out flames if a gas
installation.
underground, such as to serve a hot tub, pool, leak ignites.
shop, other building or for a natural gas fueled • Requested meter location is not usable
• Use a neighbor’s phone or find a pay phone
standby generator, it needs to be maintained. or fails to meet minimum clearances (see Things to know about natural gas safety and call MGE at (608) 252-1111. (If you must
It is your responsibility to maintain this piping. Chapter 4, Selecting a gas meter location).
use your cellular phone, be sure you are well
If your buried piping is not maintained, it may • The foundation is not sufficiently back- When using any energy source, it is wise to be away from the building.)
leak or corrode. Be sure to periodically inspect filled to support the meter or service aware of and follow certain precautions to keep
• For emergencies, call 9-1-1.
buried pipes for leaks, and if the piping is metal- piping. yourself and those around you safe. Here are
lic, inspect for corrosion. Make sure repairs are some of the things you should know to safely
• Alterations that must be made to meet
done immediately to correct any unsafe condi- obtain gas service and use it safely once it has
local codes are not completed.
tion. A corrosion control company or a plumbing been established in your structure.
or heating contractor can help inspect and repair • In some cases, MGE will require a con-
it. crete pad to support the gas meter.
Call before you dig!
If you plan to excavate near your buried
piping, it should be located in advance and the
Be sure to call to have all underground utilities
excavation should be done by hand. A locating
located any time you plan to dig on your property.
service can help locate the piping if you are not
sure of its location. For free locating of utility- Call Diggers Hotline at 1-800-242-8511 to
owned lines (typically from the street to your have all underground utilities on your property
meter), call Diggers Hotline three business days identified at least three working days before you
in advance at 1-800-242-8511. dig.
NOTE: This is required even if you think you know there are
no other utilities where you intend to dig.

6 23
 Chapter 1
Steps to a Smooth Installation
When and how to shut off gas service In a nonemergency situation
The basics: understanding the installation What natural gas equipment
When an emergency strikes, it is not always nec- If you need gas service to be shut off for a tem- will be installed in your new facility?
essary to shut off your natural gas service. Know- porary, nonemergency situation, shut off service
at the fuel-line valve located near the particular Before MGE installs your natural gas facilities, it is
ing when and how to shut off natural gas service
appliance . important to understand the overall components Next, you will need to decide what natural gas
can save you from being without gas service
of an installation. You are responsible for your equipment will be installed so you can inform
needlessly.
natural gas fuel line and appliance hookup. MGE MGE of your estimated natural gas load. Evaluate
is responsible for the installation of the natural your total natural gas load by adding up the Btu
gas main, service, and meter (see Figure 1). inputs for all equipment being installed (immedi-
When to shut off your gas service ate and future), and tell us the desired pressure
delivery at the point of connection to the meter.
It is necessary to shut off your gas service at the Remember, besides space and water heat-
service shutoff valve at the meter only when you ing, natural gas can be used for air-conditioning,
hear or smell natural gas leaking. clothes drying, cooking, pool and spa heating,
barbecues, fireplaces, patio heaters, and genera-
tors. Be sure to consider all the options.
How to shut off your gas service
in an emergency situation
Customer fuel line
If there is an emergency situation and you need The fuel line is the gas piping (installed, owned,
to shut off gas service at your meter, follow these and maintained by the customer) that runs from
three steps: the meter to the customer’s equipment. There are
three types of fuel lines you can use:
Step Action Figure 1. Example of typical gas system components.
1. Locate the service shutoff valve (usually the first
fitting) on the natural gas supply pipe coming Getting started with 1. Rigid steel piping. Typically, threaded, rigid
out of the ground near the meter. the installation process steel pipe is used for natural gas piping. This
type of pipe has been used in the gas industry
Before the installation process can begin, you for a long time and is a reliable alternative for
2. Use a long-handled wrench to turn the valve need to know the following: house piping.
one-quarter turn so the lever is crosswise to the
pipe.
2. Flexible corrugated stainless steel tubing
Is there a gas main located near your site? (may require two-pound pressure delivery).
This is a new alternative that is gaining
To determine if a natural gas main is located near
3. Once the gas is off, leave it off. Call MGE to popularity because of ease of installation.
your building site, call MGE Gas Engineering at
inspect the system, check, and relight appli- Although flexible, corrugated stainless steel
(608) 252-7933 or (608) 252-7931.
ances. tubing (CSST) and fitting material is more
If there is no gas main located near your build- expensive to purchase than rigid steel pipe.
ing site, MGE will need to review and estimate
the feasibility of extending gas facilities to you. If
MGE determines that extending a gas main to you
is needed, main extension charges may apply.

Figure 11. Gas service shutoff valve

24 5
Overview:
Bringing Natural Gas to Your Building Site
What is carbon monoxide? Know the early symptoms
of carbon monoxide poisoning
T his checklist notes the steps to bring natural gas to your
construction site. The information in this handbook
applies to MGE customers who require new nonresidential
plans (if new construction) and the legal
description or tax parcel identification. Carbon monoxide (CO) is an odorless, taste-
less, and invisible gas which can build up when If you think someone is suffering from carbon
natural gas service. If additional information is needed, • Call MGE after your fuel line has been any fuel-burning equipmentûan automobile,
contact a local MGE customer construction services repre- monoxide poisoning, move the person outside to
inspected and approved by your city or county fireplace, natural gas or oil furnace, wood stove,
sentative. fresh air immediately and seek medical help.
building department so MGE may unlock the propane heater, charcoal grill, or kerosene heater
valve, turn on the meter, and light your appli- has insufficient air to burn the fuel completely. Early symptoms include:
GAS ENGINEERING DEPART- ances (if necessary). Carbon monoxide exposure can be dangerous. • Dizziness
MENT ✓✓Removal of the lock or operation of the
• Flu-like symptoms
Commercial/Industrial and Multifamily shutoff valve may damage this equipment. Safety precautions
Customer Responsibilities: Only authorized MGE personnel can remove • Weakness
the lock and operate the valve. Here are suggestions to guard against carbon
monoxide exposure in any structure: • Nausea and vomiting
• Call MGE Gas Engineering Department to
• Use only fuel-burning equipment inside the • Partial loss of muscular control
determine if a natural gas main is located near
your building site.
MGE’s Responsibilities: structure that is designed to operate indoors. • Drowsiness
Vented gas equipment must vent to the out-
• Decide on your gas equipment and inform • Determine and inform you of gas availability. • Consider calling 9-1-1 if you have
side according to the manufacturer’s specifi-
MGE of its requirements. these symptoms
• Perform an economic feasibility study, if appli- cations.
✓✓MGE offers different delivery pressure cable. • Make sure fuel-burning equipment is main-
options that depend upon equipment load tained and operated safely and properly.
and equipment pressure requirements, • Notify you of:
which may result in special meter set and ✓✓Charges, if any. • Never run an automobile engine, lawn mower,
customer installation requirements. portable generator, or any combustion engine
✓✓Right-of-way or easement requirements. in an enclosed space.
• Complete and return the Gas Service Applica-
✓✓Additional permit requirements, if neces- • Keep flues and chimneys free of debris and
tion (provided by an MGE representative) via:
sary. clear of soot buildup.
✓✓The internet at https://www.mge.com/
• Install the natural gas main, service, and • Consider the installation of a carbon monox-
my_mge/serviceforms/installation/service-
meter set assembly. ide detector, particularly near sleeping areas
installation.asp
• Turn on and test your natural gas meter. in a structure.
✓✓Fax to MGE New Services at (608) 252-
5623, or
✓✓Mail to: Scheduling:
Madison Gas and Electric Co.
New Services • Scheduling will be based on a mutually
Post Office Box 1231 agreed-upon time frame that is consistent
Madison, Wisconsin 53701-1231 with your needs, permit requirements, and
• Provide MGE Gas Engineering Department design criteria.
with an approved, complete set of civil site

4 25
Appendix C Preface
Codes and jurisdictions
Protection of Gas System from Back Pressure
or Vacuum What this handbook contains
This handbook shall not be interpreted to conflict
with the regulations of the State of Wisconsin
This handbook contains common information on or other regulatory bodies having jurisdiction.
A device shall be installed to protect MGE’s equip- Interconnection for Standby Fuels nonresidential service which includes:
ment/system should our customer’s equipment MGE’s requirements may be more stringent. Local
create a vacuum or back pressure (192.355)(a). • Commercial and industrial buildings codes and requirements related to the planned
Where a supplementary gas for standby use is
work should be addressed before any construc-
Natural gas compressors connected to MGE’s connected downstream from a meter or a service • Apartment complexes tion begins.
system shall be connected through a check valve regulator where a meter is not provided, equip-
• Multifamily structures
capable of withstanding the outlet pressure of the ment to prevent backflow shall be installed
compressor. (NFPA 5.3.2.1).
How to contact MGE
A three-way valve installed to admit the standby MGE’s service territory map
supply and at the same time shut off the regular
supply of natural gas shall be permitted to be Please direct any technical questions regarding
For your reference, the Territory Map in Appen- the information in this booklet to MGE’s Gas
used for this purpose (NFPA 5.3.2.2). dix A provides the general boundaries for MGE’s Engineering Department at (608) 252-7933 or
natural gas service. (608) 252-7931.
If you have any general billing questions
regarding your account, contact one of our cus-
Glossary of terms
tomer service representatives at (608) 252-7222
or 1-800-245-1125 from 7:00 a.m. to 7:00 p.m.
For your convenience, glossary terms appear in weekdays. You may also contact us by e-mail at
bold italics throughout the handbook the first mge@mge.com.
time they are referenced (e.g., meter).

MGE’s service providers

Scheduling
MGE contracts with a partner company, KS
The time needed for engineering, scheduling, Energy, to provide construction services. The
and construction of the work will vary depending project manager and employees who install your
upon the complexity of the job and the volume of service may work for these service providers on
work requested by MGE customers. Contact your MGE’s behalf.
operations scheduling representative at (608)
252-7373 for current construction scheduling.

26 3
 Glossary
Chapter 4: Meter Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Selecting a Gas Meter Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Appliance shutoff valve - A valve readily acces- DOT (Department of Transportation) -
Required Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 sible and operable by the customer, located on U.S. Department of Transportation Office of
the fuel line at or very near the appliance. Pipeline Safety initiates and enforces regulations
Locations to Avoid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 relating to gas pipeline safety nationwide. Wis-
• Open position - Valve handle is parallel with
Minimum Meter Clearance Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 consin State Department of Transportation initi-
the line.
ates and enforces regulations relating to the use
Meter Set Assembly Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 • Closed position - Valve is crosswise or at a of public rights-of-way in the state.
Meter Installation and Turn-On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 right angle to the fuel line.
Guard Post and Curb Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Dry Utility - Power, phone, cable, or natural gas.
Backfill - Earth or other material used to refill a
trench. Also the act of refilling a trench.
Chapter 5: Pressure Gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Easement - A legal document entitling its holder
What is Pressure Gas? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 the right to use a specified parcel of property.
British thermal unit (Btu) - Quantity of heat nec- Easements give MGE the right to install under-
Requirements for Pressure Delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
essary to raise one pound of water one degree ground natural gas facilities on private property.
Upgrading Facilities to Accommodate Pressure Delivery . . . . . . . . . . . . . . . . . . . . 20 Fahreneheit at sea level pressure. The heating
quality of the gas. (One cubic foot of natural gas
contains about 1,000 Btu.) Emergency - A situation in which there is an
Appendices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 immediate threat to life or property. In the case of
Appendix A: MGE’s Natural Gas Service Territory Map . . . . . . . . . . . . . . . . . . . . . 22 natural gas, an emergency is an immediate threat
Carbon dioxide (CO2 ) - A gas which is a product and/or the uncontrolled escape of gas.
Appendix B: Natural Gas Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 of combustion, resulting when carbon unites with
What is Natural Gas? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 sufficient oxygen to produce complete combus-
tion. When natural gas burns completely, it Fuel line - Gas piping from the meter to the appli-
Things to Know About Natural Gas Safety . . . . . . . . . . . . . . . . . . . . . . . . . . 23 produces carbon dioxide and water vapor as well ance that is owned and maintained by the cus-
- Call Before You Dig! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 as heat. tomer.
- What to do if You Suspect a Natural Gas Leak . . . . . . . . . . . . . . . . . . . . . . 23
When and How to Shut Off Gas Service . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Carbon monoxide (CO) - A poisonous combustible Ignition temperature of natural gas - Natural gas
gas produced by the incomplete combustion of ignites at about 1,100 degrees Fahrenheit.
- When to Shut Off Your Gas Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
carbon or reduction of carbon dioxide.
- How to Shut Off Your Gas Service in an Emergency Situation . . . . . . . . . . . . . . 24
Ignitor - Any device used to light gas. A spark
- In a Nonemergency Situation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Combustion - The process of burning requiring ignitor uses an electric spark generated across an
- Gas Service Shutoff Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 three components: fuel, air, and ignition tem- air gap for this purpose.
What is Carbon Monoxide? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 perature.

- Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 • Complete combustion of natural gas results in Joint utility trench - Two or more utilities occupy-
carbon dioxide and water vapor; harmless. ing a common trench.
- Know the Early Symptoms of Carbon Monoxide Poisoning . . . . . . . . . . . . . . . . 25
• Incomplete combustion of natural gas can
produce carbon monoxide and aldehydes;
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 potentially hazardous. Load (Gas) - The connected load is calculated by
totaling the Btu rating for all gas appliances con-
nected to the meter.

2 27
 Table of Contents
Main (Gas) - The distribution line (or pipe) that Natural gas - A naturally occurring mixture of
serves as a common source of supply for more flammable hydrocarbon and nonhydrocarbon Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
than one service line. Owned and maintained by gases found in porous geologic formations What This Handbook Contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
MGE. beneath the earth’s surface often in association
with petroleum. It’s supplied as a fuel for millions MGE’s Service Territory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
of applications worldwide. The chemical composi- Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Manifold - Usually two or more natural gas meters tion is approximately 96 percent methane,
on one service line and regulator. 2 percent ethane, and 2 percent inert gases. Scheduling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Codes and Jurisdictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Mercaptan - An organic chemical odorant added Propane gas (C3H8 ) - A colorless flammable gas How to Contact MGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
to natural gas to give it a distinctive smell to alert found in petroleum and natural gas. It is odor- MGE’s Service Providers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
customers in case of leaks. Natural gas is odor- ized to make it easy to detect (smells sort of like
less in its natural state. Mercaptan smells some- garlic), heavier than air (specific gravity of 1.5),
thing like rotten eggs. and has a Btu of 2,544 per cubic foot, whereas Overview: Bringing Natural Gas to Your Building Site . . . . . . . . . . . . . . . . . . . . . . . . . . 4
natural gas contains about 1,000 Btu per cubic
foot.
Meter - A device for measuring and recording the Chapter 1: Steps to a Smooth Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
volume of gas used. The Basics: Understanding the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Rate - Method of charging for energy usage. In the
case of natural gas, for therms used. Getting Started With the Installation Process . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Meter set assembly shutoff valve - A positive Is There a Gas Main Located Near Your Site? . . . . . . . . . . . . . . . . . . . . . . . . . 5
shutoff valve on all metering and/or service regu-
lating facilities. The valve is located immediately Regulator (also Pressure regulator) - A device to What Natural Gas Equipment Will Be Installed in Your New Facility? . . . . . . . . . . . . 5
upstream (on the service line side) of the meter lower the gas pressure. District regulators lower Customer Fuel Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
set assembly. the pressure in mains. Meter regulators lower
pressure at the meter, and appliance regulators Underground Fuel Line Piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
• Open position - Valve handle is parallel with
the line (gas is flowing through the meter). lower pressure at the appliance. Factors That Can Delay Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

• Closed position - Valve is crosswise or at a Job Site Safety Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

right angle to the fuel line (gas is not flowing Right-of-way - A collection of easements and/ Locating Other Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
through the meter). or permits allowing the holder to specific limited
use of a parcel(s) of property (such as running a
gas main through private properties or a dedi- Chapter 2: Codes and Property Issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Methane gas (CH4 ) - A hydrocarbon gas that is cated area for use by the public for travel and Relevant Inspections and Local Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
the main component of natural gas (about 96 per- utilities). This term refers to the land itself, not
cent). It is colorless, odorless, and flammable and the right of passage over it. (See also Easement.) Easements and Public Right-of-Way Issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
the same substance produced in some swamps,
sewers, and landfills.
Riser - The portion of the service that terminates Chapter 3: Natural Gas Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
aboveground at the structure to support the Ordering Gas Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Multiple meter - Two or more meter sets branch- meter.
ing off separate risers. Bringing the Natural Gas Main to a New Commercial, Industrial, or Multifamily Facility . . . 9
Step 1: Application Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Riser valve - See meter set assembly shutoff
valve. Step 2: Design Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Step 3: Construction Scheduling Process . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

28 1
 Service - The pipe which carries gas from the Stub - The portion of the gas service from the
main to the customer’s meter. main to the property line.

Service shutoff valve - A convenient shutoff Therm - A therm of gas contains 100,000 Btu of
located outside of the customer’s building. If energy and is roughly equivalent to 100 cubic
the meter is located outside of the building, the feet of gas.
meter set assembly shutoff valve may also be the
service shutoff valve. In some commercial service
applications this buried valve may be located in Trench - An excavated ditch of specific depth and
the right-of-way at the customer’s property line. width into which underground utility lines are
installed.

© Copyright 2007, Madison Gas and Electric Co.

✓✓Fall 2012 Edition

29
 Gas Service
Handbook
Commercial/Industrial &
Multifamily Developments

MADISON GAS AND ELECTRIC CO. • MADISON, WISCONSIN

GS1315 09/27/2012