PART A : 3 Transformer Design Software - TDPro supports & Computes
TRANSFORMER TYPES Distribution,
Power,
Isolation, Ultra Isolation, Lighting,
Converter and Inverter Duty
REFERANCESTANDARDS IS2026 ANSI GOST
IS1180 CBIP SABS
IS11171 ECBC WAPDA
IEC 60076 EU-ECO
RATING 5 KVA to 80000 KVA, 3 phases up to 138 KV class, with 2 windings ( plus
regulating winding beyond 10 MVA)
COOLING TYPES Dry type (VPI & CRT) and
Mineral Oil cooled
Ester Oil cooled
CORE MATERIALS CRGO and
AMORPHOUS
CORE CONSTRUCTION Wound Shell Type
Wound Core Type
Rectangular Type
Amorphous Shell Type
Amorphous Core Type
Circular / Circular Stacked Core &
Flat / Flat Core
Elliptical
EI
WINDING MATERIAL Copper,
Aluminum &
Copper- Clad Aluminum
Cu and Al for HV and LV respectively
WINDING TYPES CO-CO
Layer-Layer Layer –CO Layer – Disc
Foil – Layer Foil – CO Foil – Disc
Disc – Disc
APPROVAL DOCUMENTS Guaranteed Technical Particular (GTP),
Core Area,
Flux Density,
No Load Loss No Load Current,
Load Loss,
Radiators Thermal Ability,
Hot Spot Temp,
Current Density Calculation,
Oil Absorption details &
Symmetrical Short Circuit Details
PART B: 3 TRANSFORMER DESIGN SOFTWARE (TDPro)
PART C: FEATURES OF 3 TRANSFORMER DESIGN SOFTWARE
• TDPro includes following modules
• Transformer Basic information • Short Circuit force calculation
• Windings and insulation • Temperature gradient
• Core and coil assembly • Noise level
• Tank, Radiator& Conservator
• To make a new design just input or select basic parameters like
• KVA rating • Cooling type
• HT & LV voltage • Phase & no of winding
• Tapping range
• TDPro automatically computes
• Flux density of transformer • Core weight stack wise
• Conduct or size • Width of each stack
• Conductor Arrangement • Length of each stack
• LV turns • Values like Axial and radial
• Día factor forces developed in the
• Core grades windings during short circuits
• Core size • Short circuit force calculation
• No. of HV coils/discs per limb • Temperature gradients for HV
• Size of HV/LV conductor(s) and LV
• Winding type–Helical, Cross • Thermal Time Constant
Over, Foil, Disc winding. • Withstand short circuits with
• Blade width of core winding temperature rise.
• Radiator width & height • Total heat to be dissipated
• Impedance and hence the total number of
• Load loss radiators
• No load losses • Core details
• Eddy loss • Weight of copper with
• Stray loss insulation and without
• Resistance insulation
• Reactance • Conservator size
• Weight of copper, iron, • Oil quantity
insulation, oil, and Mass • Bill of material
weight of transformer
• HV Turns
• By Optimizing design, you will get
• Raw Material Costing of transformer
• Losses -no load loss, eddy loss, stray loss, and load loss of transformer
• Tank dimensions
• Energy efficient transformers
• Hot spot temperature rise calculation.
PART D: BENEFITS OF 3 TRANSFORMER DESIGN SOFTWARE
Because of the optimized design that gets generated quickly in 2 to 3 minutes, it allows
user to edit parameters, as he wishes. You can customize the design to meet your own
inventory needs using various parameters of cores, windings, tank assembly etc. that
costless for you to purchase and are best for easy production.
• Engineering time required to complete a design is reduced to mere minutes. This is
especially valuable when you need to get quick and accurate quotations to your
customers.
• Because all calculations are done automatically, human errors are eliminated which in
turn eliminate costs associated with these. This aspect is also very important to the
productive capacity of your design engineers as design stress is alleviated.
• Check the results and if the results are not satisfied or not matching with your
specifications, change the default values as per your specifications to get the desired
results. You can get results as per your requirements.
• Estimation and costing sheets are generated in the different format (PDF, XL etc.) for
easy access, printing and sending the same via email to clients for approval, in house
departments like design, QC, purchase, estimation, production, dispatch. So TDPro
saves time, energy, and revenue.
• The bill of material will have all component details like, quantity, weight, values of
variable parameters, material code, material specification, reference drawing &
Remark etc.
• Through this software, user will get final output as
O Bill of Material
winding
Core Assembly
Tanking &Finishing
Others like parmawood ring stiffeners etc.
O Generate Guaranteed Technical Parameters (GTP)
o General Arrangement Diagram of Transformer
o Rating Plate
o Terminal Marking Plate
o 2D & 3D Drawings
Part E : 3D/2D OUTPUT’S OF TDPro
1. Frame Part (2D / 3D)
2. Conservator (2D / 3D)
3. Tank (3D /2D)
a)Radiator type with conservator type
b) Corrugated fin with conservator type
PART E : 2D / 3D OUTPUT’s OF TDPRO (Continue………)
c) Elliptical tube radiator type
d) Elliptical tank type
Cover (2D /3D)
PART E :2D / 3D OUTPUT’s OF TDPRO (Continue………)
4. General Arrangement Drawing (2D / 3D)
PART F: Chirab’s Scope
SUPPLY
Sr. No. Item Quantity
1. Transformer Design Software – TDPro CD 1 No.
2. Hardware lock (USB, to be installed on PCs) as As ordered
software license
PART G : Customer Scope
Computer System with
• Intel Core i7Processor@ 3.30 GHz or higher Version,
• RAM 8GB minimum, Hard disk 1 TB minimum + 256 GB SSD minimum
• Minimum 4 GB Graphics Card , 15.6 HD LED
• 64 bit Windows 10 Professional or ultimate SP1 Operating System and Internet
information Service installed.
• Screen Resolution : 1366 x 768.
• Full access with administrative rights.
• TeamViewer Version 9 or higher (download link:
[Link]
2c8/)
• Dot NET framework 4.5 software duly installed
MS Office 2013 or latest version duly installed
• Third party Inventor 3D software license version 2018 or higher has to be procured by the
client separately, if advanced version of TDPro is being bought
PART H: Quotation Request Format
SN Information to be furnished for Quotation To be filled by Purchaser
1 Max Rating of the Transformer to be Designed (kVA)
2 Which Package you wish to buy
(Basic / Advanced)
Basic / Advanced
Basic – Electrical & Documentation
Advanced – Basic + 2D & 3D Drawings*
3 Software License to be valid for how many years
(Max 3 years)
4 How Many Computers you would like to have TDPro
installed?
5 How many Licenses ( Dongles) to be purchased?
(License will be USB Dongle and will work on one
computer at a time)
*Purchaser need to buy Auto Desk Inventor separately
