&EJUJPO
3&$:$-&3(6*%&
4*."5*$
&541
#BTF6OJU
3FGFSFODFQSPEVDU&4#1#"
5IJTEPDVNFOUDPWFSTBMMUIFWBSJBOUTJOUIFSBOHF
&4#1#" &4#1#" &4#1#6 &4#1#6
&4#1%" &4#1%" &4#1%6 &4#1%6
&4#1#" &4#1#" &4#1## &4#1##
&4#1## &4#1## &4#1#$ &4#1#'
&4#1%" &4#1%" &4#1%$
TVQQPSUJOEVTUSZTJFNFOTDPN
About this guide
1
Safety instructions
2
SIMATIC Recommended tool
3
ET 200SP
Recycler Guide for SIMATIC Disassembly instructions
4
ET 200SP BaseUnit
Explanation of substances
and components
5
Product Information
Received material fractions
6
Disclaimer of liability
7
07/2025
A5E54588212-AA
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified persons are those who, because of their training and experience, are familiar with the installation,
assembly, commissioning, operation, decommissioning and disassembly of the product and can recognize risks
and avoid possible hazards.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the application described in the catalog and the associated usage
information. If products and components from other manufacturers are used, these must be recommended or
approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens Aktiengesellschaft. The remaining trademarks in
this publication may be trademarks whose use by third parties for their own purposes could violate the rights of
the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens Aktiengesellschaft A5E54588212-AA Copyright © Siemens 2025.
Digital Industries Ⓟ 08/2025 Subject to change All rights reserved
Postfach 48 48
90026 NÜRNBERG
GERMANY
Table of contents
1 About this guide................................................................................................................................. 5
2 Safety instructions.............................................................................................................................. 6
3 Recommended tool............................................................................................................................. 7
4 Disassembly instructions.................................................................................................................... 8
5 Explanation of substances and components...................................................................................... 14
6 Received material fractions................................................................................................................ 15
7 Disclaimer of liability.......................................................................................................................... 16
Recycler Guide for SIMATIC ET 200SP BaseUnit
4 Product Information, 07/2025, A5E54588212-AA
About this guide 1
In order to conserve important resources, we work on reducing the materials we use and
supporting the recycling economy right from the product design stage. An important way to
achieve this goal is the resource recovery of electronic products at the end of their service
life.
The Siemens Recycler Guides provide recyclers of electronic products with instructions on
how to disassemble products safely in order to maximize resource recycling. The Recycler
Guides provide step-by-step disassembly instructions and material composition information
to help recyclers direct specific materials to specialized recyclers.
Disassembly may only be carried out by specialists trained in the recycling of electronic
devices. The recycler is responsible for independently evaluating and ensuring compliance
with all applicable environmental, health and safety regulations. This includes, among other
things, the legal requirements in the area of management, handling, shipping and disposal as
well as applicable laws to ensure the health and safety of all employees involved.
If you have any questions or feedback regarding this Recycler Guide, please use this email
address (mailto:
[email protected])
Recycler Guide for SIMATIC ET 200SP BaseUnit
Product Information, 07/2025, A5E54588212-AA 5
Safety instructions 2
The recycler is responsible for independently evaluating all activities of its employees in
performing or supporting the work and ensuring compliance with all applicable legal
requirements. This includes, but is not limited to, laws regarding the health and safety of all
employees performing or assisting in that work. The recycler is also responsible for assessing
the workplace and ensuring that the area in which the work is carried out meets all
ergonomic requirements to ensure the protection of its employees.
Danger notice (DIN EN ISO 7010)
Warning against hand injuries Warning against pointed/sharp objects
Wear personal protective equipment throughout the recycling process.
Wear hand protection Wear a mask
Wear eye protection Wear foot protection
Wear protective clothing
WARNING
Electric shock due to residual charges in power components
Due to the capacitors, dangerous voltage is still present for up to 15 minutes after the power
supply has been switched off. Touching live parts can lead to death or serious injury.
Wait 15 minutes before checking that there is no voltage and starting work.
Recycler Guide for SIMATIC ET 200SP BaseUnit
6 Product Information, 07/2025, A5E54588212-AA
Recommended tool 3
To disassemble the product, we recommend using the following tools:
NN
Cutter knife Slotted screwdriver
PP
Embossing tool
Recycler Guide for SIMATIC ET 200SP BaseUnit
Product Information, 07/2025, A5E54588212-AA 7
Disassembly instructions 4
The following guide provides detailed information on how to disassemble the product at the
end of its service life and on what materials you can collect and recycle.
In doing so, you support the recycling economy.
Components of the product
Position Part Material Disassembly step
1 Spring release Polybutylene terephthal Step 4
ate
2 Contact support cover Polyamide Step 3
3 Assembled PCB Electronics Step 4
4 Contact support slide Polyamide Step 1
5 Support Polycarbonate Step 3
6 Assembled PCB Electronics Step 6
7 Clip Polycarbonate Step 6
8 Latch Polycarbonate Step 5
9 Compression spring Stainless steel Step 5
Recycler Guide for SIMATIC ET 200SP BaseUnit
8 Product Information, 07/2025, A5E54588212-AA
Disassembly instructions
Position Part Material Disassembly step
10 Shield connection clamp Copper alloy Step 7
11 Power bus Enclosure: Polyamide Step 7
Plug-in contacts: Cop
per/precious metal/tin
12 Shield connection clamp Copper alloy Step 2
Product group
Designation Order number
BU15-P16+A0+2B 6ES7193-6BP00-0BA0
BU20-P16+A0+2B 6ES7193-6BP00-0BU0
BU15-P16+A0+2D 6ES7193-6BP00-0DA0
BU20-P16+A0+2D 6ES7193-6BP00-0DU0
BU15-P16+A0+2B 6ES7193-6BP00-2BA0
BU20-P16+A0+2B 6ES7193-6BP00-2BU0
BU15-P16+A0+2D 6ES7193-6BP00-2DA0
BU20-P16+A0+2D 6ES7193-6BP00-2DU0
BU15-P16+A10+2B 6ES7193-6BP20-0BA0
BU20-P12+A4+0B 6ES7193-6BP20-0BB0
BU20-P6+A2+4B 6ES7193-6BP20-0BC1
BU20-P8+A4+0B 6ES7193-6BP20-0BF0
BU15-P16+A10+2D 6ES7193-6BP20-0DA0
BU20-P6+A2+4D 6ES7193-6BP20-0DC0
BU20-P12+A0+4B 6ES7193-6BP20-0BB1
BU15-P16+A10+2B 6ES7193-6BP20-2BA0
BU20-P12+A4+0B 6ES7193-6BP20-2BB0
BU20-P12+A0+4B 6ES7193-6BP20-2BB1
BU15-P16+A10+2D 6ES7193-6BP20-2DA0
Recycler Guide for SIMATIC ET 200SP BaseUnit
Product Information, 07/2025, A5E54588212-AA 9
Disassembly instructions
Dismantling the product
Follow these steps for disassembly:
1. Disassembly of the contact support
1. To unlock the contact support slide, use a slotted screwdriver to lever the snap lock on the
contact support.
2. Remove the contact support slide.
2. Disassembly of the shield connection clamp
1. Use a slotted screwdriver to lift the interlocks on the shield connection clamp on each
side.
2. Remove the shield connection clamp.
Recycler Guide for SIMATIC ET 200SP BaseUnit
10 Product Information, 07/2025, A5E54588212-AA
Disassembly instructions
3. Disassembly of the contact support cover
1. Use a cutter knife to cut into the contact support cover on each side. See orange line in
the figure.
2. Remove the cover.
4. Disassembly of all parts of the support
1. Remove the spring release.
2. Remove the contact support cover.
3. Remove the assembled PCB.
4. Remove the contact support slide.
Recycler Guide for SIMATIC ET 200SP BaseUnit
Product Information, 07/2025, A5E54588212-AA 11
Disassembly instructions
5. Disassembly of the latch
1. Use a slotted screwdriver to lever on the right and left sides of the latch at the same time.
2. Remove the latch and the compression spring.
6. Remove the clip and the assembled PCB
1. Use an embossing tool to push the side interlocks inward and lift the top interlock.
2. Remove the clip and the assembled PCB.
Recycler Guide for SIMATIC ET 200SP BaseUnit
12 Product Information, 07/2025, A5E54588212-AA
Disassembly instructions
7. Disassembly of the shield connection clamp and the power bus
1. Press the 4 snap locks on the shield connection clamp with a slotted screwdriver.
2. Remove the shield connection clamp and the power bus.
Recycler Guide for SIMATIC ET 200SP BaseUnit
Product Information, 07/2025, A5E54588212-AA 13
Explanation of substances and components 5
Components according to Directive 2012/19/EU Annex VII
You must remove at least the following substances, mixtures and components from the
product:
Substance/mixture/component Position Disassembly step
PCBs with a surface area greater than 10 cm2 3 Step 4
Plastic with brominated flame-retardants 3 Step 4
Additional information
In order to support the recycling economy, SIEMENS creates transparency that goes beyond
the regulatory requirements. See the table for additional information on smaller PCBs or
displays, as well as metal alloys containing elements that may be critical at the end of the
service life, such as beryllium or lead.
This information does not fall within the scope of Annex VII of Directive 2012/19/EU.
Substance/mixture/component Position Disassembly step
PCBs with a surface area less than 10 cm2 6 Step 6
Recycler Guide for SIMATIC ET 200SP BaseUnit
14 Product Information, 07/2025, A5E54588212-AA
Received material fractions 6
All results from this process must be managed, handled, and disposed of in accordance with
applicable waste laws and regulations including, but not limited to, the Waste Framework
Directive and its national legislation in Europe and worldwide.
The following table contains the most important material fractions. The table does not claim
to be complete.
Position Possible material fractions (not exhaustive)
1 Polybutylene terephthalate (Pbt)
5, 7, 8 Polycarbonate
2, 4, 11 (enclosure) Polyamide
9 Stainless steel
3, 6, 11 (plug-in contact) Copper, precious metals, tin
10, 12 Copper alloy
Recycler Guide for SIMATIC ET 200SP BaseUnit
Product Information, 07/2025, A5E54588212-AA 15
Disclaimer of liability 7
The Recycler Guide is for information purposes only.
This Recycler Guide does not guarantee the composition of any product or that the product
will retain a specific composition for a specific period of time. Therefore, all warranties,
assurances, conditions implied by statute or common law are excluded to the fullest extent
permitted by applicable law.
The Recycler Guide provides information about the disassembly process of an appliance so
that the components can be assigned to the correct recycling channels. Reuse of dismantled
components is not permissible.
Siemens therefore assumes no liability for errors or consequences that may result from
the use of this information to the greatest possible legal extent.
Please note that the data in this Recycler Guide cannot be compared to data calculated based
on product category rules (PCRs) other than the above standards. The values given are only
valid in the specified context and cannot be used directly to create the environmental
compatibility assessment of a plant.
Recycler Guide for SIMATIC ET 200SP BaseUnit
16 Product Information, 07/2025, A5E54588212-AA
